Ransome Direct Fired Vaporizers RH50, RH80 & RH120 The RH Series vaporizer consists of a vertical ASME pressure vessel that is directly heated by a gas fired burner. Millivolt powered burner controls maintain consistent vapor temperature. They are completely self contained and require no outside power supply, making them an excellent choice for remote instalations or those with unreliable power supply. Capacities are available in 50, 80 and 120 GPH. UL Ransome 9V Relight System Installed optionally, the Ransome 9V Relight System protects against pilot outage due to unusally turbulatent atmospheric conditions, and is operated by four 9V batteries and two Solar Panels and is for use in the field where 1V line power is unavailble. UL RH240 RH240 Direct-Fired LP-Gas Vaporizer Ransome s RH240 Series provides an economical, dependable source of Liquified Petroleum (LP) gas vapour for a wide range of applications up to 240 gallons per hour. RH240 units are completely self-contained and require no outside power source. UL RH200 thru RH00 The larger RH Series vaporizers are similiar in design to the smaller models, with the exception of the liquid level controls, which require 1V AC power. Capacities are available from 200-00 GPH, making them a compact and economical choice for larger installations. XE0120-009 UL SURREY 1.855.258.3835 CALGARY 1.866-629.7847 EDMONTON 1.800.661.7770 SASKATOON 1.800.667.5886
Ransome Water-Bath Vaporizers RW Series Water-Bath Vaporizer Selection Chart - RW Series The RW Series vaporizer consists of a vertical ASME pressure vessel, submerged in a water-bath and heated by a gas fired burner. Millivolt powered burner controls maintain consistent water temperature. They respond well to fluctuation in demand and are an excellent choice in cold climates or were heavy ends are a problem. Capacities are available from 0 to 900 gallons per hour. ID Series Water-Bath Horizontal Vaporizer The ID Series vaporizer consists of a horizontal ASME pressure vessel, submerged in a heated water-bath. A microprocessor based burner control system controls the firing of a forced draft burner to maintain water temperature. They are designed for continuous, unattended duty in all climates with capacities available from 500 to 6000 GPH making them an excellent choice for utilities and large industrial Selection Chart - ID Series WWW.MAXQUIP.CA WINNIPEG 1.844.278.5771 OAKVILLE 1.800.801.8512 MONTREAL 1.877.629.7847
Ransome Electric Vaporizers RE Series Electric Vaporizer The RE Series vaporizer consists of a vertical carbon steel ASME pressure vessel that is electrically heated with replaceable cartridge heating elements. They are microprocessor controlled and perform well under adverse weather conditions. All units are rated for Class I, Div II hazardous locations and require less set-back than gas fired vaporizers. Capacities are available from 25 to 400 GPH. RE-A Series Electric Vaporizer (Economy) The RE-A Series Economy vaporizer utilizes the same pressure vessel, heating elements and operating controls as the standard models but it constructed without a cabinet. Functionally, it is identical to our standard electric vaporizer, with all the same features and benefits. RE Series Electric Tank Heater The RE Series tank heater consists of a horizontal ASME pressure vessel fitted with a (pressure operated) flanged immersion heater. Tank heaters are used to maintain pressure by supplementing the natural vaporization capabilities of the storage tank during peak demand or other conditions that cause a loss of tank pressure. Capacities are available from 12 to 600 GPH. SURREY 1.855.258.3835 CALGARY 1.866-629.7847 EDMONTON 1.800.661.7770 SASKATOON 1.800.667.5886
Ransome Steam/Water Vaporizers VS Series Steam Vaporizer The VS Series vaporizer consists of a vertical shell and tube heat exchanger that is heated by saturated steam at 15 to 50 psig. Steam and condensate flows are accurately controlled to maintain the desired vapor temperature. They are designed for continuous, unattended duty in hazardous locations with capacities ranging from 55 to 11,800 GPH, making them an excellent choice for large industrial applications where steam is available. VS Series Hot Water Vaporizer The VS Series hot water vaporizer is a steam heated unit that has been adapted for use with 180 degree hot water, which reduces its capacity by 50%. Water flow is accurately controlled to maintain vapor temperature. They are designed for continuous, unattended duty in hazardous locations with capacities ranging from 27 to 5,900 gallons per hour, making them an excellent choice for large industrial application where a source of hot water is available. Millions of BTU/HR Propane Capacity CF/HR GAL/HR Approx. Required BTY/HR Minimum Heated Hot Water 60 F to 180 F GPH Approximate Shipping Weight LB KG Ransome Model 2.51 4.75 15. 30.20 45.75 65.65 9.80 172.70 249.80 352.30 539.87 1,000 1,819 6,004,508 18,195 27,292 43,668 68,777 99,344 140,1 214,701 28 50 165 330 500 750 1,200 1,890 2,730 3,850 5,900 53,570 97,400 321,420 642,840 974,000 1,461,000 2,435,000 3,896,000 5,318,040 7,291,900 11,493,200 15 25 25 25 50 890 1,000 1,125 1,250 1,500 1,805 2,360 2,915 3,470 4,025 4,580 404.5 454.5 511.4 568.2 681.8 820.5 72.7 1325 1577.3 1829.5 2081.8 VHW 55 VHW 0 VHW 330 VHW 660 VHW 00 VHW 1500 VHW 2400 VHW 380 VHW 5460 VHW 00 VHW 11800 WWW.MAXQUIP.CA WINNIPEG 1.844.278.5771 OAKVILLE 1.800.801.8512 MONTREAL 1.877.629.7847
Ransome Mixer Vaporizers PAM Series Direct-Fired Vaporizer/Air Mixer The PAM Series vaporizer/mixer consists of an RH series vaporizer and an M series mixer packaged together to produce a propane/air mixture with a heating value equivalent to natural gas. With output pressure from 5-30 psig and capacities from 14.7 to 3.2 million BTU/HR they are the simplest and most affordable choice in standby equipment for many commercial, agricultural and industrial applications. PAMW Series Water-Bath Vaporizer/Air Mixer The PAMW Series vaporizer/mixer consists of an RW series vaporizer and an M series mixer packaged together to produce a propane/air mixture equivalent to natural gas. With output pressues of 5-30 psig and capaciities from 14.7 to 3.2 million BTU/HR they are the most affordable choice for those applications requiring a water-bath vaporizer M Series Venturi Mixer The M Series mixer uses a venturi to produce a propane/air mixture with a heating value equivalent to natural gas. When connected to an indirect fired vaporizer they are ideal for use in hazardous locations due to their Class I Div II rating. With output pressues of 5-30 psig and capacities from 14.7 to 3.2 million BTU/HR they are an affordable choice in standby equipment for many commercial, agricultural and industrial applications. ST750 Surge Tank The ST750 Surge Tank is a necessary part of every PAM, PAMW and M Series mixer installation due to their cycling nature. The tank has a 750 gallon water capacity and is ASME rated for 50 psig. Designed with flanged openings, it will connect to the mixer directly or with the optional 5 ft. spool connector. The ST750 Trim Kit completes the installation with the necessary relief valve and accessories. SURREY 1.855.258.3835 CALGARY 1.866-629.7847 EDMONTON 1.800.661.7770 SASKATOON 1.800.667.5886
Ransome Mixer Vaporizers PAME Series Electric Vaporizer/Air Mixer The PAME Series vaporizer/mixer consists of an RE Series vaporizer and an M series mixer packaged with an integral 500 gallon surge tank. Compact in size with a Class I, Div II rating, it is ideal for sites with minimal clearance. With capacities of 7.3 and 14.7 million BTU/HR, it is a simple and compact option in standby equipment for many commercial and small industrial applications. MPM Series Modulating Proportioning Mixer The MPM Series mixer is a highly accurate, electronically controlled unit designed to produce precise propane/air mixtures. Designed for continuous, unattended duty, they are often the choice for utilities and other large industrial applications. Available with output pressures of - 200 psig and capacities from 22.1 to 78 million BTU/HR. SSVM Series Tank Heater Venturi Mixer LP-Gas is a highly concentrated source of energy, with 2516 BTU s per cubic foot fross heat content. It is too rich to use as a direct substitute for natural gas without the proper dilution. Ransome Manufacturing s series of Mixers or Vaporizer/Mixers blends in just the right amount of air for an equivalent mixture. A mixture with specific gravity of 1.21 (1480 BTU/Cu. Ft.) will approximately match 0.6 specific gravity natural gas with 00 BTU/Cu. Ft. gross heat content. Please contact your local Maxquip branch if you require detailed breakdowns or schematics. The SSVM is a complete propane storage, vaporization and mixing system, all in one very unique package. With propane tank sizes up to 1999 gallons and mixer capacities up to 14.7 million BTU/HR it is the most compact emergency standby system on the market today. Ideally suited for hospitals, schools and other small commercial applications. WWW.MAXQUIP.CA WINNIPEG 1.844.278.5771 OAKVILLE 1.800.801.8512 MONTREAL 1.877.629.7847
Ransome Electric LP-Gas Vaporizer Standard Features: Ransome s unique mechanical liquid level inlet valve. It provides positive shutoff of LP-Gas liquid, preventing liquid from entering the outlet. Electronic Temperature Controller. The controller operates the heater circuit(s) for the desired outlet vapor temperature set point. The controller also monitors for high temperature and turns off heater in the event of a high temperature condition. Electric resistance heater. Provides the heat required for vaporization. ASME stamped relief valve. Each vaporizer unit is adequately protected in accordance with NFPA 58 and California Title 8 codes. 240/480V AC, 3PH, 60 Hz Input power. No other power is required. (380V AC, 3PH, 50Hz China ONLY) All sizes are capable of infinite turndown and will maintain a ready supply of vapour from zero load to full capacity. At no load, only enough heat will be generated to maintain set point temperature. Standard electrical configuration Class I, Division I. SURREY 1.855.258.3835 CALGARY 1.866-629.7847 EDMONTON 1.800.661.7770 SASKATOON 1.800.667.5886
Premier Ductable Unit Heaters These versatile heaters are great for small or large work spaces, renovation jobs, and any applications where low noise or an enclosed flame is important. Premier heaters can be used to provide heat or simple air circulation inside, or be ducted in from the outside. LP, NG, and dual fuel models available Versatile indoor or outdoor placement of heater Direct-fired = 99.97% fuel efficiency High volume of air output for maximum heat distribution Dependable, electronic spark ignition Switch fuels easily with simple valve turn on dual fuel units Tri-shield fi nish provides superior protection against abrasion and corrosion Built-system for maximum safety and ease of troubleshooting Easy to transport Vent mode for circulation of air Dual fuel models include dual fuel regulator 20 remote start thermostat standard 12 extendable ducting (optional-part #26346 (12 ) for 80 & 170 models, and part #22835 (18 ) for 350 models) CSA certified Quiet operation Can be used with or without ducting Enclosed flame promotes safer work environments Btu/h Rating Heated Air Output (CFM) Fuel Consumption (max.) LP Gas (lbs./hr.) Natural Gas (cu.ft/hr.) Two Stage Output Amps (starting/continuous operation) Amps (standard 15 amp circuit) Motor Horsepower Dimensions (in.) Length Width Height Shipping Weight (lbs.) 80 170 170 DF 350 350 DF 80,000 170,000 170,000 175,000/350,000 350,000 450 1,200 1,200 2,500 2,500 3.7 7.9 7.9 16.2 16.2 80 170 170 350 350 No No No Yes No 5.0 / 1.5 7.3 / 5.0 7.3 / 5.0 25.0 / 9.0 25.0 / 9.0 Yes Yes Yes Yes* Yes* 1/8 1/3 1/3 1 1 29.5 32.3 32.3 48.3 48.3 13.5 24.3 24.3 28.0 28.0 22.0 32.0 32.0 41.0 41.0 79.0 161.0 162.0 320.0 320.0 *Amps spike over 15 during initial start-up. Check breaker capability. Now with 2 year warranty. WWW.MAXQUIP.CA WINNIPEG 1.844.278.5771 OAKVILLE 1.800.801.8512 MONTREAL 1.877.629.7847
Premier 80 Parts Schematic Item Description Part Number 1 Regulator Propane Gas 26377 Natural Gas 21999 2 Handwheel with Spring Propane Gas 26395 3 Universal Hose Kit, 15 ft. Hose w/ Adapters 24600 4 Adapter 1/2 NPT x 5/8-18 06655 5 Ell 09309 6 Screw 09425 7 Valve, Gas Control Propane Gas 22076 Natural Gas 22078 8 Manifold Assembly w/ Orifice Propane Gas 26391 Natural Gas 26438 9 Orifice, Burrner Propane Gas 571625 Natural Gas 571626 Transformer 26412 11 Thermostat Kit 09454 12 Washer, Bolt, Spacer 25866 13 Harness, Wire, Burner End 26383 14 Wire, Igniter 25840 15 Control Ignition 25865 16 Bracket, Ignition Control 26411 17 Support Leg 26378 18 Harness, Wire, Motor End 26382 19 Base 26380 20 Bracket.Igniter/Sensor 571663 21 Igniter 25841 22 Burner 26484 23 Screws and S acers 571211 Item Description Part Number 23 1 Re Screws ulator and Spacers 571211 24 Switch, High Limit, Burner End (275 F) 03933 25 Chamber, Heat 571666 26 Harness, Wire, Status Lights 26381 27 Switch, Selector 26385 28 Cord, Power 26379 29 Light.Stat us, 24 Volt 26392 30 Light.Status, 120 Volt 26393 31 Hanger, Hose 571619 32 Door Assembly, Burner End 26434 Propane Gas Natural Gas 26433 33 Handle 25859 34 Case Assembly 26389 Propane Gas Natural Gas 26387 35 Door Assembly, Fan End 26435 36 Thermostat Bracket 26401 37 Latch, Door 26437 38 Fan Assembly 26384 39 Motor 20292 40 Motor Mount 571686 41 Fan 570304 42 Switch, High Limit, Fan End (250 F) 571671 43 Housing,Fan 571612 44 Switch,Air Proving 26485 45 Bracket, Burner 571649 46 Bracket, Flame Arrestor 571609 47 Handle.Door 26479 SURREY 1.855.258.3835 CALGARY 1.866-629.7847 EDMONTON 1.800.661.7770 SASKATOON 1.800.667.5886
Premier 170 Parts Schematic PREMIER 170 PART SCHEMATIC 42 43 52 41 40 31 35 39 34 32 38 33 36 50 37 47 48 46 45 29 30 49 27 23 26 44 19 22 21 24 25 11 28 20 18 14 A 4 12 9 A 13 16 17 15 A 5 51 6 2 1 8 7 3 WWW.MAXQUIP.CA WINNIPEG 1.844.278.5771 OAKVILLE 1.800.801.8512 MONTREAL 1.877.629.7847
Premier 170 Parts List Item Description Part Number 1 Regulator Propane Gas Natural Gas 26419 09795 2 Hand Wheel with Spring Propane Gas 26395 3 Universal Hose Kit, 15 ft. Hose w/ Adapters 24600 4 Wheel Kit 26418 5 Axle 26415 6 Cotter Pin 26417 7 Kit, Leg Bracket 26413 8 Bolt and Washer 25866 9 Handle, Bracket, Burner End 26426 Handle, Bracket, Motor End 26427 A Nut, Bolt & Washer 26443 11 Wire Harness, Motor End 26406 12 Wire Harness, Burner and Gas Control End 26407 13 Transformer 26412 14 Adapter,Hose, 1/2 NPT x 5/8-18 Propane Gas Natural Gas 06655 25873 15 Ell 09309 16 Valve, Gas Control Propane Gas Natural Gas 22076 22078 17 Screw 09425 18 Manifold Assembly with Orifice Propane Gas Natural gas 26404 26441 19 Bracket, Ignition Control 264 20 Ignition Control 25865 21 Orifice Propane Gas Natural gas 21573 09787 22 Wire, Igniter 25840 23 Igniter 25841 24 Bracket, Igniter 25843 25 Burner with Mounting Hardware 25842 26 Burner Mounting Hardware 571211 27 Switch, High Limit, Burner End (275 F) 25869 28 Chamber, Heat 26403 29 Cord, Power 26379 30 Thermostat Kit w/ 20 ft. Cord 09454 31 Wire Harness, Status Lights 26408 32 Light,Status, 120 Volt 26393 33 Light,Status, 24 Volt 26392 34 Switch, Heat/Vent, Rocker 26385 35 Plug 25747 36 Bracket, Regulator Storage 26402 37 Bracket, Thermosat Storage 26401 38 Handle, Sliding 571760 39 Hanger, Hose 571619 40 Latch, Door 26437 41 Door, Burner End Propane gas Natural Gas 26432 26431 42 Case Assembly Propane Gas Natural Gas 26398 26397 43 Door, Louvered, Motor End 26430 44 Housing Assembly w/motor, Fan, High Limit and Air Proving Switches 26439 45 Motor 25834 46 Mount, Motor 25835 47 Fan 25849 48 Switch, High Limit, Motor End (190 F) 25846 49 Switch, Air Proving 25858 50 Housing, Fan 26440 51 Base 26414 52 Handle,Door 26479 Warranty Policy HEATER L.B. White Co., Inc. warrants that the component parts of its heater are free from defects in material and workmanship, when properly installed, operated, and maintained in accordance with the Owner s Manual safety guides and labels contained with each unit. If, within 12 months from the date of purchase by the end user, any component is found to be defective, L.B. White Co., Inc. will at its option, repair or replace the defective part or heater, with a new part or heater, F.O.B., Onalaska, Wisconsin. A warranty card on file at L.B. White will automatically qualify the heater and its component parts for warranty consideration. If a warranty card is not on file, a copy of the bill of sale will be required to establish warranty qualification. If neither is available, the warranty period will be 12 months from date of shipment from L B. White. PARTS L.B. White Co., Inc. warrants that replacement parts purchased from the company and used on the appropriate L. B. White heater are free from defects both in material and workmanship for 12 months from the date of purchase by the end user. Warranty is automatic if a component is found defective within 12 months of the date code marked on the part. If the defect occurs more than 12 months later than the date code but within 12 months from the date of purchase by the end user, a copy of a bill of sale will be required to establish warranty qualification. The warranty set forth above is the exclusive warranty provided by L.B. White, and all other warranties, including any implied warranties or merchantability or fitness for a particular purpose, are expressly disclaimed. In the event any implied warranty is not hereby effectively disclaimed due to operation of law, such implied warranty is limited in duration to the duration of the applicable warranty stated above. The remedies set forth above are the sole and exclusive remedies available hereunder. L.B. White will not be liable for any incidental or consequential damages directly or indirectly related to the sale, handling or use of the heater, and in any event L.B. White s liability in connection with the heater, including for claims based on negligence or strict liability, is limited to the purchase price. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. REPLACEMENT PARTS & SERVICE Contact your local Maxquip branch for replacement parts and service or call the L.B. White Co., Inc. at (800) 345-7200 for assistance. Be sure that you have your heater model number and configuration number when calling. SURREY 1.855.258.3835 CALGARY 1.866-629.7847 EDMONTON 1.800.661.7770 SASKATOON 1.800.667.5886