REMOVE EXISTING WALL MOUNTED RADIATOR SILL HEIGHT @ 2'-0 1/2" LINE OF CEILING CHANGE LINE OF CEILING CHANGE TO BARREL VAULT CEILING Family Room EXISTING WOOD BURNING FIREPLACE TO BE REMOVED AND INSTALL NEW GAS FIREPLACE INSERT - TO BE CONFIRMED Kitchen / Dining Table 15'- EXISTNG MEXICAN TILE FLOORS TO BE REMOVE AND REPLACED WITH NEW OAK WOOD FLOORS TO MATCH EXSTING WIDTH / PATTERN / STAIN BY ROSEWOOD FLOORING NOTE : HYDRONIC FLOOR HEATING SYSTEM REMOVE EXISTING WOOD FLOOR AND REPLACE WITH NEW OAKWOOD FLOORS TO MATCH FAMILY ROOM EXISTING FREESTANDING STEREO CABINET TO BE REMOVED C/H 6'-9-1/4" DN EXISTING FLOOR PLAN EXISTING FLOOR PLAN SCALE: 1/4" = 1'-0" ID-1
REMOVE EXISTING WALL MOUNTED RADIATOR SILL HEIGHT @ 2'-0 1/2" LINE OF CEILING CHANGE TO BARREL VAULT CEILING Family Room ID-6 1 EXISTING WOOD BURNING FIREPLACE MANTLE AND HEARTH TO BE REMOVED AND INSTALL NEW GAS FIREPLACE INSERT - TO BE CONFIRMED AS PER SPECIFICATIONS Kitchen / Dining Table 15'- C/H 14'-6-1/2" LINE OF MARBLE FACED WALL TV ABOVE GAS FIREPLACE INSERT BELOW ST-1 S-1 LINE OF FLOATING CABINETRY NEW SOLID OAK FLOORING TO MATCH EXISTING WIDTH / PATTERN / STAIN BY ROSEWOOD FLOORING NOTE: NEW HYDRONIC FLOOR HEATING SYSTEM EXISTING WALNUT CABINETRY TO REMAIN C/H 6'-9-1/4" DN FIREPLACE CABINETRY PLAN FIREPLACE CABINETRY PLAN VIEW SCALE: 1/4" = 1'-0" ID-2
REMOVE EXISTING WALL MOUNTED RADIATOR SILL HEIGHT @ 2'-0 1/2" CP-01 FINISH SCHEDULE LEGEND- TYPICAL Note: Refer to Finishes Schedule in Drawing Set CP-01 CARPET / BROADLOOM INCLUDING CARPET TILES LINE OF CEILING CHANGE TO BARREL VAULT CEILING CF-01 FB-01 CUSTOM FINISH - SPECIALTY FAUX / GOLD + SILVER LEAF / ANTIQUING FABRIC - WALL PANELS / MILLWORK ETC GL-01 FABRIC - WALL PANELS / MILLWORK ETC Family Room EXISTING WOOD BURNING FIREPLACE MANTLE AND HEARTH TO BE REMOVED AND INSTALL NEW GAS FIREPLACE INSERT - TO BE CONFIRMED AS PER SPECIFICATIONS L-01 LM-01 LIGHTS - ANY HARD WIRED LIGHT FIXTURE FLOORING - LAMINATE Kitchen / Dining Table 15'- C/H 14'-6-1/2" LINE OF MARBLE FACED WALL TV ABOVE GAS FIREPLACE INSERT BELOW S-1 LT-01 MW-01 LAMINATE - PLASTIC / WOOD / METAL LAMINATES CUSTOM MILLWORK / CABINETRY / MOULDINGS / CASING / BASEBOARDS / DOORS ETC FOR EITHER STAIN ( ST ) OR PAINT ( PT ) FINISH MR-01 MIRROR FINISH - CLEAR / TINTED / ETCHED / PRINTED MT-01 METAL - ANY METAL FINISH INCLUDING STAINLESS STEEL / BRASS ETC LINE OF FLOATING CABINETRY PM-01 PT-01 PLASTER MOULDINGS - CROWN / CEILING / WALL PAINT FINISH - WALLS / CEILING / MILLWORK / CABINETRY ETC, FINISHES: EGGSHELL ( E ) / FLAT ( F) / SEMI GLOSS ( SG ) HIGH GLOSS ( HG ) SATIN ( S ) EXISTING WALNUT CABINETRY TO REMAIN C/H 6'-9-1/4" NEW SOLID OAK FLOORING TO MATCH EXISTING WIDTH / PATTERN / STAIN BY ROSEWOOD FLOORING NOTE: NEW HYDRONIC FLOOR HEATING SYSTEM PB-01 RB-01 S-01 SS-01 ST-01 T-01 PLUMBING FIXTURE - TO INCLUDE ALL PLUMBING FIXTURES FLOORING - RUBBER STONE - MARBLE / GRANITE / QUARTZ / PORCELAIN SLAB MATERIAL SOLID SURFACE - COUNTERTOP / BACKSPLASH STAIN FINISH - MILLWORK / CABINETRY TILE - STONE / QUARTZ / GLASS / PORCELAIN / METAL ETC. VL-01 WC-01 FLOORING - VINYL WALLCOVERING - VINYL / PAPER / FABRIC DN WD-01 HARDWOOD - FLOORING SOLID WOOD / ENGINEERED FURNITURE PLAN VIEW SCALE: 1/4" = 1'-0" FURNITURE PLAN ID-3
REMOVE EXISTING WALL MOUNTED RADIATOR SILL HEIGHT @ 2'-0 1/2" LINE OF CEILING CHANGE TO BARREL VAULT CEILING Family Room EXISTING WOOD BURNING FIREPLACE MANTLE AND HEARTH TO BE REMOVED AND INSTALL NEW GAS FIREPLACE INSERT - TO BE CONFIRMED AS PER SPECIFICATIONS Kitchen / Dining Table 15'- C/H 14'-6-1/2" LINE OF MARBLE FACED WALL TV ABOVE GAS FIREPLACE INSERT BELOW S-1 LINE OF FLOATING CABINETRY NEW SOLID OAK FLOORING TO MATCH EXISTING WIDTH / PATTERN / STAIN BY ROSEWOOD FLOORING NOTE: NEW HYDRONIC FLOOR HEATING SYSTEM EXISTING WALNUT CABINETRY TO REMAIN C/H 6'-9-1/4" DN FLOOR FINISHES PLAN FLOOR FINISHES PLAN SCALE: 1/4" = 1'-0" ID-4
REMOVE EXISTING WALL MOUNTED RADIATOR SILL HEIGHT @ 2'-0 1/2" JB LIGHTING LEGEND JUNCTION BOX FOR PENDANT FIXTURE. G.C. TO PROVIDE BLOCKING FOR WEIGHT OF FIXTURE. WS WALL SCONCE TO BE MOUNTED AT 66' A.F.F. UNLESS OTHERWISE NOTED RECESSED POTLIGHT 5'-5 1/2" 5'-9" LINE OF CEILING CHANGE TO BARREL VAULT CEILING CL F SP L.E.D. RECESSED CABINET LIGHT EXHAUST FAN IN-CEILING RECESSED SPEAKER Family Room 3'-6 3/4" EXISTING WOOD BURNING FIREPLACE MANTLE AND HEARTH TO BE REMOVED AND INSTALL NEW GAS FIREPLACE INSERT - TO BE CONFIRMED AS PER SPECIFICATIONS WP FLUORESCENT LIGHT FIXTURE SURFACE MOUNTED LIGHT FIXTURE RECESSED WATERPROOF LIGHT FIXTURE Kitchen / Dining Table 15'- 3'-8" 8'-0 1/4" C/H 14'-6-1/2" 3'-6 3/4" LINE OF MARBLE FACED WALL TV ABOVE GAS FIREPLACE INSERT BELOW S-1 UC 3 UNDER CABINET LIGHTS SINGLE POLE SWITCH THREE WAY SWITCH D 3'-8" 2'-8 3/4" 3'-11 1/2" STAINLESS STEEL CEILING FAN 3'-3 1/2" 2'-4 3/4" D D CUSTOM LACQUER FINISH CABINETRY BOTH SIDES OF MARBLE FACED FIREPLACE / TV DISPLAY WALL LINE OF FLOATING CABINETRY UNDER SHELF / CABINET LOW VOLTAGE STRIP LIGHTING SWITCHED AS SHOWN NEW SOLID OAK FLOORING TO MATCH EXISTING WIDTH / PATTERN / STAIN BY ROSEWOOD FLOORING NOTE: NEW HYDRONIC FLOOR HEATING SYSTEM D DA GFI WP DIMMER SWITCH DOOR ACTIVATED SWITCH ELECTRICAL LEGEND DUPLEX RECEPTACLE (REGULAR 110V DUPLEX OUTLET) GFI REGULAR 110V DUPLEX OUTLET WITH GROUND FAULT INTERRUPTER WATERPROOF RECEPTACLE WITH GROUND FAULT INTERRUPTER FOR EXTERIOR EXISTING WALNUT CABINETRY TO REMAIN C/H 6'-9-1/4" CV CENTRAL VACUUM HALF SWITCH 110V DUPLEX RECEPTACLE 220 VOLT DUPLEX OUTLET HARDWIRE (FOR KITCHEN EXHAUST AND MOTORIZED DRAPERY) FLOOR RECEPTACLE 110V DUPLEX OUTLET FLUSH WITH FINISHED FLOOR DN TELEPHONE INTERNET TELEVISION, WALL MOUNTED RECEPTACLE REFLECTED CEILING PLAN SCALE: 1/4" = 1'-0" TELEPHONE RECEPTACLE FLUSH WITH FINISHED FLOOR INTERNET RECEPTACLE FLUSH WITH FINISHED FLOOR NOTE: ALL RECEPTACLES TO BE HORIZONTAL IN BASEBOARD UNLESS OTHERWISE NOTED. NOTE: ALL RECEPTACLES TO BE MOUNTED AT 12" A.F.F. UNLESS OTHERWISE NOTED. REFLECTED CEILING PLAN ID-5
CUSTOM LACQUER / MAPLE CABINETRY INCLUDING COUNTERTOP FOR STAIN FINISH INTERIOR / EXTERIOR - NACRE MULTI RECEPTICLE STRIPS FLUSH TO COUNTERTOP BUILD OUT CABINET BACK PANEL TO ACCOMODATE SHALLOW RECEPTICLE BOX INSTALLATION 2'-2 1/2" LOW VOLTAGE LIGHTING IN CABINET BULKHEAD 1'- 2'-2 1/2" TV / SPEAKER BAR AND FIREPLACE ELECTRICAL REQUIREMENTS TO BE CONFIRMED WITH IGNE FERRO / AUTOMATED ENTERTAINMENT 32" / 44" STEREO / TV EQUIPMENT ELECTRICAL RECEPTICLES @ 32" AND 44" AFF 44" 2" 1'-2" 1'-8" LED STRIP LIGHTING RECESSED INTO MAPLE SHELVING SITE DIMENSION 3'-6 3/4" 3'-6 3/4" 3'-1 3/4" PLAN @ FIREPLACE / MEDIA WALL / CUSTOM CABINETRY Scale: 1/2" = 1'-0" 15'-6 3/4" RE POSITION EXISTING LOW VOLTAGE LIGHTING IN EXISTING CEILING NOTE: SWITCHING EXISTING LINE OF EXISTING CEILING @ 8'- 4 1 2" NOTE: START OF BARREL VAULT CEILING LINE OF PULLOUT ALBUM DRAWERS BELOW - SEE ELEVATION SITE DIMENSION 8'-11" 4'-6 1/4" LACQUER CABINETRY WITH INTERIOR ADJUSTABLE SHELVING TOUCH LATCH DOOR PANELS NOTE: LACQUER FINISH INTERIOR / EXTERIOR EXISTING WINDOW TRIM FOR PAINT FINISH DRYWALL FOR PAINT FINISH WOOD BASEBOARD FOR PAINT FINISH 4 1/2" 1 1/2" 1 ID-6 5" REMOVABLE SLOTTED TOEKICK TO ALLOW ACCESS TO SUBWOOFER SUB DF 10 4"HIGH X 16"WIDE X16"DEEP NOTE: LACQUER FINISH SLOT INTERIORS PT-1 4'-9" 4'-0" 4'-0" 1'-2" CALACATTA ORO SLAB MARBLE FIREPLACE/TV WALL ELEVATION @ FIREPLACE / MEDIA WALL / CUSTOM CABINETRY Scale: 1/2" = 1'-0" ST-1 MARBLE SEAM 8 1/2" SAMSUNG 65" UN65F9000 UHD TV RECESSED AND FLUSH TO MARBLE NOTE: GREY METAL FRAME BY IGNE FERRO 5 3/4" S-1 CENTRE SPEAKER BAR BEHIND GREY METAL MESH AND FRAME BY IGNE FERRO KINGSMAN MARQUIS MQRB5143N AS PER IGNE FERRO SPECIFICATIONS FLUSH TO MARBLE SURROUND GREY METAL SIDE PANELS AND FRAME BY IGNE FERRO LOW VOLTAGE RECESSED LIGHTING LACQUERED MILLWORK FACIA FLUSH TO MARBLE FLUSH TO CABINET FACE PT-1 MARBLE SEAM STEREO EQUIPMENT SHELVING PROVIDE ELECTRICAL RECEPTICLES BEHIND FLUSH SEAM 2-3/8 TV EQUIPMENT SHELVING PROVIDE ELECTRICAL RECEPTICLES BEHIND MW-2 PT-2 LED STRIP LIGHTING RECESSED IN SHELVING TURNTABLE ON COUNTER NOTE: PROVIDE COUNTERTOP GROMMET TO ALLOW PLUG INTO RECEPTICLE BELOW 1'-9 1/2" 5'-4" 1'-9 1/2" 4'-6 1/4" CRITICAL CABINET DIMENSION 4'-5 3/4" CRITICAL DIMENSION TO BE CONFIRMED BY IGNE FERRO CENTRE LINE OF TV FLUSH SEAM CENTRE LINE OF FIREPLACE CRITICAL CABINET DIMENSION 1 ID-6 NATURAL AIR FLOW 2-3/8 REVEAL DETAIL AT TOP OF DOOR PANEL TO ALLOW FOR NATURAL AIR FLOW AND HEAT ESCAPE VENTILATION GRILLE AIR INTAKE MAPLE CABINETRY INCLUDING COUNTERTOP FOR STAIN FINISH INTERIOR / EXTERIOR 1 1/2" RECORD ALBUM PULL OUT DRAWERS BELOW ACCESSORY TOUCHLATCH DRAWERS ABOVE UNDER CABINET LED STRIP LIGHTING OPEN BELOW STAINED BACK PANEL 2-3/8 1/2" 2" 1 1/2" 5" 1'-3" 1'-2 3/4" 1 1/4" 4 1/2" 1'-9 3/4" 1 1/4" 3'-0" 8'-4 1/2" 2" 2" 2" 6" MW-2 1'-0 1/2" 1'-8" 1'-8" 1'- PT-1 1'-2" PT-2 1 1/4" SECTION @ CUSTOM CABINETRY Scale: 1/2" = 1'-0" LOW VOLTAGE RECESSED LIGHTING REVEAL DETAIL AT TOP OF DOOR PANEL TO ALLOW FOR NATURAL AIR FLOW AND HEAT ESCAPE LED STRIP LIGHTING RECESSED INTO UNDERSIDE OF SHELVING DOUBLE WALL SWITCHES IN CABINET GABLE DIMMABLE LIGHT SWITCH FOR CABINETRY LIGHTING + WALL RECEPTICLE TURNTABLE WIRING TROUGH REMOVABLE METAL OR WOOD DIVIDER TO ACCOMODATE DEPTH OF ALBUMS VENTILATION GRILLE SATIN NICKEL FINISH SIZE: 14.5" X 3" LED STRIP LIGHTING RECESSED INTO UNDERSIDE OF CABINET 1 ID-6 CABINETRY ELEVATION @ FIREPLACE ID-6
4'-7" 5'-2" 5'-2" 3 1/2" 6" 8" 7" 6" 6" 2'-8" 2'-8" 12" X 24" SILVER WHITE POLISHED MARBLE TILE SUPPLIER: CIOT MARBLE COUNTERTOP SEE ELEVATION + DETAILS 12" X 24" SILVER WHITE POLISHED MARBLE TILE SUPPLIER: CIOT MARBLE PATTERN : 1/3 COUNTERTOP SEE ELEVATION + DETAILS PLAN VIEW - FOYER / POWDER ROOM TILE PATTERN OPTION A PLAN VIEW - FOYER / POWDER ROOM TILE PATTERN C Scale: 3/8" = 1'-0" Scale: 3/8" = 1'-0" 4'-7" 5'-2" 2'-8" FOYER + POWDER RM. TILE PATTERN 12" X 24" SILVER WHITE POLISHED MARBLE TILE SUPPLIER: CIOT MARBLE PATTERN : BRICK COUNTERTOP SEE ELEVATION + DETAILS PLAN VIEW - FOYER / POWDER ROOM TILE PATTERN B Scale: 3/8" = 1'-0" ID-7
4'-7" 5'-2" 2'-4" 2'-8" 3 1/2" 6" 8" 12" X 24" SILVER WHITE POLISHED MARBLE TILE SUPPLIER: CIOT MARBLE 7" T-1 6" 6" 2'-8" COUNTERTOP SEE LARGER PLAN + ELEVATION INCLUDING PLUMBING FIXTURE SPECIFICATIONS ST-2 PULLOUT DRAWER WITH FULL EXTENTION DRAWER HARDWARE - TOUCH LATCH OPERATION NOTE: MARBLE FACING APPLIED TO DRAWER / MARBLE FLUSH TO MARBLE COUNTERTOP EDGE PROFILE 4 1/2" COUNTERTOP / BACKSPLASH WITH 3/8" TOP EDGE BEVEL NOTE 1 1/2" BUILDUP EDGE PROFILE WITH 3/8" BEVEL WATERWORKS HENRY FAUCET - POLISHEDNICKLE FINISH / MANCHESTER MRLVCU UNDERMOUNT SINK NOTE: PTRAP AND ALL FITTINGS BELOW SINK TO BE POLISHED NICKLE FINISH NOTE: OPTIONAL LED STRIP LIGHTING SWITCHED TO EXISTING SWITCHING GANG ST-2 PLAN VIEW - FOYER / POWDER ROOM TILE PATTERN OPTION A Scale: 3/8" = 1'-0" PLAN VIEW - CUSTOM MARBLE VANITY Scale: 3/4" = 1'-0" 8" LUTRON HORIZONTAL RECEPTACLE COLOUR: WHITE (WH) ARCHITECTURAL MATT 3/4" MARBLE BACKSPLASH WITH 3/8" TOP BEVEL 4 1/2" LARGE VENETIAN STYLE MIRROR ON BACK WALL MR-1 WALLCOVERING TO MATCH FOYER KRAVET: WINFIELD THYBONY ASIAN ESSENCE WOS3459 VISCOSE / SILK 36" WIDTH WC-1 3 1/2" 1 1/2" 1 3/4" MARBLE BUILTUP EDGE PROFILE FLUSH TO VANITY MARBLE APRON ST-2 MARBLE DRAWER / APRON FLUSH TO COUNTERTOP PROFILE PULLOUT DRAWER WITH FULL EXTENTION DRAWER HARDWARE - TOUCH LATCH OPERATION NOTE: MARBLE FACING APPLIED TO DRAWER / MARBLE FLUSH TO MARBLE COUNTERTOP EDGE PROFILE NOTE: OPTIONAL LED STRIP LIGHTING SWITCH TO BE GANGED WITH EXISTING SWITCHING WATERWORKS HENRY FAUCET - POLISHED NICKLE FINISH / MANCHESTER MRLVCU UNDERMOUNT SINK NOTE: P-TRAP AND ALL FITTINGS BELOW SINK TO BE POLISHED NICKLE FINISH NOTE: OPTIONAL LIGHT GREYTINTED MIRROR ON BACK WALL MR-2 POWDER ROOM - MARBLE VANITY EXISTING BASEBOARD FOR PAINT FINISH MW-3 ELEVATION - CUSTOM MARBLE VANITY Scale: 3/4" = 1'-0" ID-8
2'-4" MAPLE DRAWER BOX FOR LACQUER PAINT FINISH PROVIDE FOR FULL EXTENTION DRAWER SLIDES AND SELF CLOSING HARDWARE 3/4" MARBLE DRAWER FACE SECURED TO MAPLE DRAWER BOX - LACQUER PAINT FINISH NOTE: ALL INTERIOR / EXTERIOR CABINET FRAME AND DRAWER TO BE LACQUER PAINT FINISH - COLOUR TO BE SPECIFIED BY DESIGNER TO MATCH MARBLE SLAB SILVER WHITE POLISHED MARBLE - SUPPLIER CIOT LINE OF EXISTING WALL LINE OF EXISTING WALL 10 3/4" CUSTOM MARBLE VANITY - DRAWER SECTION 1 3/4" MARBLE BUILTUP EDGE PROFILE FLUSH TO VANITY MARBLE DRAWER FACE 3" TOP VIEW Scale: 3' = 1'-0" MAPLE DRAWER BOX FOR LACQUER PAINT FINISH PROVIDE FOR FULL EXTENTION DRAWER SLIDES AND SELF CLOSING HARDWARE 5" 3/4" MARBLE DRAWER FACE SECURED TO MAPLE DRAWER BOX - LACQUER PAINT FINISH NOTE: ALL INTERIOR / EXTERIOR CABINET FRAME AND DRAWER TO BE LACQUER PAINT FINISH - COLOUR TO BE SPECIFIED BY DESIGNER TO MATCH MARBLE SLAB SILVER WHITE POLISHED MARBLE - SUPPLIER CIOT LED STRIP LIGHTING 1/4"TINTED MIRROR ON BACK WALL ABOVE EXISTING BASEBOARD CUSTOM MARBLE VANITY - PROFILE LINE OF EXISTING DRYWALL MARBLE VANITY - DETAILS ID-9 Scale: 3" = 1'-0"
4'-7" 5'-2" INSTALL NEW LUTRON HORIZONTAL RECEPTACLE COLOUR: WHITE (WT) ARCHITECTURAL MATT 1'-4" 1'-4" DELETE EXISTING RECEPTACLE AND PATCH DRYWALL READY FOR WALL COVERING INSTALLATION RECESSED MR-16 POT LIGHTS 34 1 2 " HORIZONTAL 16" 1'-4" 5" HORIZONTAL RECEPTACLE 34 1/2" 11 1/2" RECESSED MR16 POT LIGHTS UNDERCABINET STRIP LIGHTING 11 1/2" 1'-4" INSTALL NEW LUTRON HORIZONTAL RECEPTACLE COLOUR: WHITE (WT) ARCHITECTURAL MATT NOTE: REMOVE AND PATCH EXISTING RECEPTICAL BELOW VANITY NOTE: OPTIONAL LED STRIP LIGHTING SWITCHED TO EXISTING SWITCHING GANG COUNTERTOP / BACKSPLASH WITH 3/8" TOP EDGE BEVEL NOTE 1 1/2" BUILDUP EDGE PROFILE WITH 3/8" BEVEL D D 3 GANG LUTRON SKYLARK CONTOUR DIMMER SWITCHES / COVER PLATES COLOUR: WHITE ( WT) ARCHITECTURAL MATTE PLAN VIEW - CUSTOM MARBLE VANITY Scale: 1 2" = 1'-0" RECESSED MR16 POT LIGHTS PLAN VIEW - FOYER / POWDER ROOM LIGHTING PLAN Scale: 3/8" = 1'-0" WALLCOVERING TO MATCH FOYER KRAVET: WINFIELD THYBONY ASIAN ESSENCE WOS3459 VISCOSE / SILK 36" WIDTH 8'-6" 3 1/2" LARGE MIRROR SIZE AS SHOWN 54" WIDE X 54" HIGH 5'-6" MARBLE DRAWER / APRON FLUSH TO COUNTERTOP PROFILE 1 3/4" MARBLE BUILTUP EDGE PROFILE FLUSH TO VANITY MARBLE APRON NOTE: LED STRIP LIGHTING SWITCH TO BE GANGED WITH EXISTING SWITCHING ELEVATION - CUSTOM MARBLE VANITY Scale: 1/2" = 1'-0" NOTE: OPTIONAL LIGHT GREYTINTED MIRROR ON BACK WALL EXISTING BASEBOARD FOR PAINT FINISH POWDER ROOM LIGHTING PLAN ID-10
FINISH SCHEDULE NOTE: TO BE READ IN CONJUNCTION WITH CURRENT INTERIOR DESIGN DRAWING SET PROJECT NAME : OLEARY RESIDENCE - FAMILY ROOM RENOVATIONS DATE: 17/01/12 REVISIONS : 17/01/11 / 17/01/08 ROOM NAME / NUMBER ITEM MATERIAL FINISH CODE SPECIFICATIONS GROUT SPECIFICATIONS SOURCE / SUPPLIER SPECIAL REMARKS FOYER RM # 100 FLOOR OAK CHANTILLY PATTERN WALLS BASEBOARD WALL PANEL OAK DOORS DOOR CASING WALL PANELLING CEILING CEILING BEAMS + CORBELS CROWN MOULDING WINDOW FRAME WINDOW CASINGS OAK OAK DRYWALL PT-1 MAPAI LIVING ROOM RM # 101 FLOOR OAK CHANTILLY PATTERN WALLS OAK BASEBOARD WALL PANEL OAK DOORS OAK DOOR CASING WALL PANELLING CEILING CEILING BEAMS + CORBELS CROWN MOULDING WINDOW FRAME WINDOW CASINGS DINING ROOM RM # 102 FLOOR OAK CHANTILLY PATTERN WALLS OAK BASEBOARD WALL PANEL OAK DOORS OAK DOOR CASING WALL PANELLING CEILING CEILING BEAMS + CORBELS CROWN MOULDING WINDOW FRAME WINDOW CASINGS FINISH SCHEDULE DETAILS + SECTIONS JANUARY, 2017 ID-11