manual W365H, W375H, W305H, W330H, W380H, W3240H, W3300H Exacta & Clarus Control 438 9200-0 06.34
Contents 3 Contents Technical data... :... 2: Transportation and unpacking... 2: Siting and floor... 3: Mechanical installation... 4: Water connections... 5: Drain connection... 6: Steam connection... 7: Connection of external liquid supplies... 8: Electrical installation... 9: Function checks... 0: The manufacturer reserves the right to make changes in design and materials specifications. Safety This machine can only be used with water. Never use dry cleaning agents. Do not allow children to operate the machine. Do not hose down or spray the machine with water. All mechanical and electrical installation must be carried out by qualified personnel. Do not bypass the door locking device. Should the machine malfunction, please report the fault to the technician responsible for the machine.
Technical data : Technical data Innerdrum volume diameter Drum speed wash extraction Heating electricity steam hot water G-factor Weight, net litres mm rpm kw kg W365H W375H W305H W330H W380H W3240H W3300H 65 75 05 30 80 240 300 520 520 595 650 725 795 795 52 52 49 49 44 42 42 00 00 025 980 930 890 820 5.4/7.5 5.4/7.5 7.5/0 3 8 23 23 x x x x x x x x x x x x x x 350 350 350 350 350 350 300 44 59 20 267 350 400 509 Connections W365H W375H W305H W330H W380H W3240H W3300H Water valves connection BSP Rec. water pressure kpa Functioning limits for water valve kpa Capacity at 300 kpa l/min Drain valve outer Ø mm Draining capacity l/min Steam valve connection BSP Rec. steam pressure kpa Functioning limits for steam valve kpa DN20 DN20 DN20 DN20 DN20 DN20 DN20 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 200-600 200-600 200-600 200-600 200-600 200-600 200-600 50-000 50-000 50-000 50-000 50-000 50-000 50-000 20 20 20 20 60 60 60 50/75 50/75 50/75 75 75 75 75 70 70 70 70 70 70 70 DN5 DN5 DN5 DN5 DN5 DN5 DN5 /2" /2" /2" /2" /2" /2" /2" 300-600 300-600 300-600 300-600 300-600 300-600 300-600 50-800 50-800 50-800 50-800 50-800 50-800 50-800 438 942-4/04
:2 Technical data Electrical connection 2 Cold water 3 Hot water 4 Hard water 5 Steam connection 6 Drain 7 Liquid detergent supply 8 Control panel 9 Soap box 0 Door opening, W365H, W375H: ø 30, W305H: ø 365, W330H: ø 395, W380H, W3240H: ø 435 A B C D E F G H I K L M N O P R S W365H 720 690 5 355 720 825 45 030 220 00 35 90 830 360 00 240 W375H 720 690 5 355 720 825 45 030 220 00 35 90 830 360 00 240 W305H 830 705 300 365 740 90 45 5 220 095 35 995 90 45 00 295 W330H 90 785 325 435 825 035 25 245 25 225 300 25 00 305 455 W380H 970 870 40 470 90 20 5 330 230 290 35 205 370 40 00 335 485 W3240H 020 95 445 500 955 55 00 360 25 320 300 240 350 360 00 360 50 W3300H 020 060 445 500 35 55 00 360 25 320 300 380 00 360 330 W365H, W375H, W305H, W330H A 8 9 B 5 G O 2 3 I L 4 7 0 C 6 F N M K D 528 5282 5283 E 6 R P Front Right side Rear side W380H, W3240H, W3300H 9 A 8 B 5 S G 2 M L I 2 3 4 7 0 C F K H 6 D 5377 5379 5378 E 6 R Front Right side Rear side 438 942-4/04 P
Technical data :3 Frequency of the dynamic force Hz Max floor load at extraction kn W365H W375H W305H W330H W380H W3240H W3300H 8.3 8.7 7. 6.4 5.5 4.8 3.7.6±0.5.8±0.5 2.3±0.5 3.0±0.5 3.9±.0 4.5±.0 5.5±.3 438 942-4/04
2: Transportation and unpacking, W365H, W375H, W305H 2 3 The machine is delivered complete with expansion bolts etc. packed inside the machine in the drum. The machine is delivered bolted onto the transport pallet and packed in a crate or box. Remove packing from the machine. Remove front panel. Remove the bolts between the machine and pallet. Mount front panel. When the machine is lifted off the pallet: Make sure that the machine does not come down on the floor with either of the rear corners first. The side panel of the machine can be damaged. Mount the feet. Place the machine on its final position. Level the machine with the feet of the machine. The machine also comes with transport safety devices (four plate angles between the support and the drum). In order to remove the safety devices: Remove front and rear panel. Remove both front metal angels. Remove both rear metal angels. The machine may not be moved with the transport securities removed. Save the transport securities for future use. 2 3 5327A 5325 5326 438 942-6/04
2:2 Transportation and unpacking, W330H, W380H, W3240H, W3300H 4 The machine is delivered complete with expansion bolts etc. packed inside the machine in the drum. The machine is delivered bolted onto the transport pallet and packed in a crate or box. Remove packing from the machine. Remove front and rear panel. Remove the bolts between the machine and pallet. Mount front and rear panel. Mount the feet. 5 NOTE! Regarding W3300H note the positioning of the two front feet. Place the machine on its final position. Level the machine with the feet of the machine. 5 5340 4 The machine also comes with transport safety devices (two plate angles between the support and the drum). In order to remove the safety devices: 6 Remove the two side panels. Remove the two transport securities. The machine may not be moved with the transport securities removed. Save the transport securities for future use. 6445 6 534 438 942-6/04
3: Siting and floor Install the machine close to a floor drain or open drain. In order to make installation and servicing the machine easier the following clearances are recommended: At least 500 mm between the machine and the wall behind and min. 50 mm on both sides of the machine whether installed next to the wall or other machines. 5327 438 942-8/0
4: Mechanical installation Mark and drill 2 holes (ø 8 mm) about 40 mm deep (W365-W305) and ø 0 mm and 50 mm deep (W330-W3240) in the positions shown. C A D A B C D E F G H W365H 495 460 0 30 375 70 40 00 B W375H 495 460 0 30 375 70 40 00 W305H 575 465 30 40 455 85 35 95 W330H 635 490 35 75 55 95 60 0 G H W380H 75 545 25 205 595 85 60 5 W3240H 790 65 5 80 670 75 60 5 F E W3300H 903 835 60 80 670 75 60 75 Front 5358 = position of feet = drilling points for expander bolts The machine shall be lifted in the bottom frame. Place the machine over the two drilled holes. Check that the machine is placed in level. Adjust with the feet. It is of utmost importance that the machine is placed in level, from side to side as well as front to rear. If the machine is not properly leveled, it may result in out-of-balance without a real out of balance in the drum. Insert the expansion bolts supplied in the holes drilled in the floor. Fit the washers and nuts, and tighten well. 438 943-0/05
5: Water connections All intake connections to the machine are to be fitted with manual shut-off valves and filters, to facilitate installation and servicing. Water pipes and hoses should be flushed clean before installation. After installation hoses should hang in gentle arcs. All connectors present on the machine must be connected up. The table shows the possible connection options, which will depend on the water types to be connected to the machine. Check the machine plates too. All water connectors must be connected up, otherwise the wash program will not function correctly. Hoses are to be of an approved type and grade, to comply with national regulations. The water pressure data is as follows: min: 50 kpa (0,4 kp/cm 2 ) max: MPa (0 kp/cm 2 ) recommended: 200-600 kpa (2-6 kp/cm 2 ) If the water pressure is below the min. value, the wash result can not be guaranteed for certain program. 438 943-2/07
5:2 Water type Water connection 2 3 4 2 3 cold cold ** cold and hot cold hot ** cold and hot cold hot cold*/ ** hot 4 W365H, W375H/N, W385N/M 5336 * For detergent container. 2 ** Only machine with Clarus Control. Extra water valve which can be used for hard water if soft water is connected to. This valve can also be used for water reuse from tank. If pump is used, it is only a water connection without valve. 3 2 4 W365H, W375H/N, W385N/M, W305H/N/M W330H/N/M 5328 2 W380H/N/M, W3240H, W3250N/M, W3300H W3330N 4 3 5339 438 943-2/06
6: Drain connection Connect a 75 mm (3") (alt. 50 mm, 2" and only W365-W305) pipe or rubber hose to the machine s drain pipe, ensuring a downward flow from the machine. Avoid sharp bends which may prevent proper draining. The drainage pipe should be located over a floor drain, drainage channel or the like so that the distance between the outlet and the drain is at least 25 mm ("). 5330 438 943-4/02
7: Steam connection The steam supply to the machine should be fitted with manual shut-off valves and filters to facilitate installation and servicing. A The connection hose must be of type ISO/307-983 or equivalent. Connection size at filter: DN 5 (BSP /2"). Steam pressure required: minimum: 50 kpa (0.5 kp/cm 2 ) 586 maximum: 800 kpa (8 kp/cm 2 ) 2 Remove the cover (A). 2 Mount the articulated nipple to the steam valve. 3 Mount the steam valve on the machine. 5862 4 Mount nipple, strainer and elbow. Note the direction of the strainer. Mount steam hose to the elbow. Check that there are no sharp angles or bends on the connected steam hose. 3 5 Mount the hose with wires between steam valve and machine. Connect wires in the steam valve. Connect ground cable to the terminal ground connection. Mount the cable connector on X46 on distribution card. 2 5863 5864 3 X46 5865 438 962-0/02
8: Connection of external liquid supplies Electrical installation must be carried out by an authorized personnel! L L2 L3 N T T2 T3 N All optional equipment connected must be EMC-approved to EN 5008- or EN 50082-2. 2 Distribution card A can be used to control external functions, output and input signals. Outputs (0-240V AC): Only Clarus Control A B 533 X7:,2 Signal "Door locked, program on" X72: 0 V (common) X72:2 Liquid supply 2 Card A X72:3 Liquid supply 2 X72:4 Liquid supply 3 X72:5 Liquid supply 4 X73: Detergent box (Y) X73:2 Detergent box 2 (Y2) X73:3 Detergent box 3 (Y3) X73:4 Detergent box 4 (Y4) X73:5 Detergent box 2 (Y22) Inputs: X70:,2 Paus/PC5 X70:3,4 Start/Stop 6052 438 943-6/04
8:2 3 Outputs (0-240V AC): Only Exacta Control X70 See Payment system 3 Card A X72: 0 V(common) (Door locked) X72:2 L (Door locked) X72:3 Liquid supply (Prewash) X72:4 Liquid supply 2 (Main wash) X72:5 Liquid supply 3 (Softener) 4 X72:6 Liquid supply 4 (Mop chemicals)* X72:7 Liquid supply 5 (Bleach) * Only for program 2M, 2M2 and 2M4. X73: Heating X73:2 Detergent box 2 (Y2) X73:3 Cold water (Y5) X73:4 Detergent box 2 (Y22) X73:5 Hot water (Y25) X73:6 Inverted drain X73:7 Drain Payment system FlexSystem X70: Price programming X70:2 Price programming X70: and X70:2 connection for price programming switch. X70:3 0 V (common) 5233A X70:4 ±24V X70:3 and X70:4 to be connected to FlexSystem. 4 5233A 438 943-6/04
8:3 4 5 PCB (COGES) X70: N X70:2 Available, signal when door is closed but program not started. X70:3 Booked, opto- input (20-230V) 5 4 6 X70:4 Booked, opto- input PCB (Camping) X70:3 Booked, opto- input (20-230V) X70:4 Booked, opto- input 5607 6 5608 438 943-6/04
8:4 4 7 4 7 Electrolux Booking System X70: L (230V), output X70:2 N, output X70:3 Booked, opto- input X70:4 Booked, opto- input Central Payment (France)/External start X70: L (230V), output X70:2 N, output X70:3 Start, opto- input (20-230V) 7 X70: X70:2 X70:3 X70:4 X70:4 Start, opto- input Price reduction 4 X70: Timer, opto- input (20-230V) X70:2 Timer, opto- input 4 8 External coin-meter X70: 0V (common), output X70:2 Coin 2 X70:3 Coin 8 X70:4 Price programming 560 438 943-6/04
8:5 9 If more signals are required the machine can be equipped with a second distribution card B (only Clarus Control). Outputs (200-240V AC): 9 Card B X75: 0 V (common) X75:2 Liquid supply 5 X75:3 Liquid supply 6 X75:4 Liquid supply 7 X75:5 Liquid supply 8 X76: 0 V (common) X76:2 Drain lock X76:3 Drain A X76:4 Drain B X76:5 Drain C X76:6 Inlet A X76:7 Inlet B X76:8 Inlet C X77: Buzzer (N) X77:2 Buzzer (L) Inputs: X74:,2 Switch between heating /heating 2 X74:3,4 No function 5743 438 943-6/04
9: Electrical installation Electrical installation must be carried out by an authorized personnel! Machines with frequency-controlled motors can be incompatible with certain types of earth leakage circuit breaker. It is important to know that the machines are designed to provide a high level of personal safety, which is why items of external equipment such as earth leakage circuit breakers are not necessary. If you still want to connect your machine across an earth leakage circuit breaker, please remember the following: contact a skilled, authorised installation company to ensure that the appropriate type of breaker is chosen and that the dimensioning is correct for maximum reliability, connect only one machine per earth leakage circuit breaker it is important that the earth wire is properly connected, including to the earth leakage circuit breaker. Mount a multi-pole switch prior to the machine to facilitate installation and service operations. The connecting cable should hang in a gentle curve. Fuse size, see table. Single-phase connection: Connect the earth and other two wires as shown in example in the figure. NAC AC 5332 5333A 438 943-8/09
9:2 Three-phase connection: 2 Connect the earth, neutral and phase wires as shown in example 3AC and 3N AC in the figure. When the installation is completed, check: that the drum is empty. that the machine operates by turning on the mains switch, starting the machine and using RAPID ADVANCE to reach the spin cycle (see operations manual). 2 3AC 3 IMPORTANT 45V 3AC machines can be supplied with 380, 400 or 45V. 240V AC machines can be supplied with 220, 230 or 240V. In the machine there is a transformer (not on models with Classic control) placed in the front control unit (under the top cover). This transformer is preset for 240V which is applicable for machines intended for 240V - or 3AC and 45V 3AC. If your supply voltage is 220 or 230V, - or 3AC or 380 or 400V 3AC the jumper on the transformer has to be moved to 230V-COM instead of COM-240V. If the jumper is not moved in the above described cases there is a risk that the machine will not work in installation sites with undervoltage. 3N AC 3 5333 5334 438 943-8/09
9:3 W365H Heating Voltage Total Fuse alternative alternative kw A No heating or Steam heating El heating 200 V 3 AC 0 208-240 V AC 0 200 V 3 AC 5.6 20 220-240 V AC 2.2 6 220-240 V AC 3.2 6 230/240 V AC 4.4 20 220-240 V AC 7.3 35 220-240 V 3 AC 3.2 0 220-240 V 3 AC 7.3 20 240 V AC 5.4 25 230/240 V 3 AC 4.4 6 230/240 V 3 AC 5.8 6 380-45 V 3/3N AC 3.2 0 400/45 V 3/3N AC 4.4 0 380/400/45 V 3/3N AC 5.8 0 380-45 V 3/3N AC 7.3 6 440/480 V 3 AC 7.9 6 380-45/220-240 V 3/3N AC 7.3 6/20 45/240 V 3N/3/ AC 7.9/5.4 6/25 438 943-8/09
9:4 W375H Heating Voltage Total Fuse alternative alternative kw A No heating or Steam heating El heating 00-20 V AC. 6 200 V 3 AC. 0 208-240 V AC. 0 200 V 3 AC 5.6 20 220-240 V AC 2.3 6 220-240 V AC 3.2 6 230/240 V AC 4.4 20 240 V AC 5.4 25 220-240 V AC 5.4 25 220-240 V AC 7.4 35 220-240 V 3 AC 3.2 0 230/240 V 3 AC 4.4 6 220-240 V 3 AC 5.4 6 220-230 V 3 AC 7.0 20 220-240 V 3 AC 7.4 25 380-45 V 3/3N AC 3.2 0 400/45 V 3/3N AC 4.4 0 380-45 V 3/3N AC 5.4 0 380-45 V 3/3N AC 7.4 6 440/480 V 3 AC 7.9 6 380-45/220-240 V 3/3N AC 7.4 6/25 45/240 V 3/3N/ AC 7.9/5.4 6/25 438 943-8/09
9:5 W305H Heating Voltage Total Fuse alternative alternative kw A No heating or Steam heating El heating 200 V 3 AC.3 0 208-240 V AC.3 0 200 V 3 AC 5.6 20 220-240 V 3 AC 3.2 6 240 V AC 5.5 25 240 V AC 7 35 230/240 V AC 5.3 25 220-240 V AC 7.4 35 220-240 V AC 9.7 50 220-240 V 3 AC 3.2 0 230/240 V 3 AC 5.3 6 220-240 V 3 AC 7.4 25 208-240 V 3 AC 9.2 35 220-240 V 3 AC 9.7 35 380-45 V 3/3N AC 3.2 0 400-45 V 3/3N AC 5.3 0 380-45 V 3/3N AC 7.4 6 380-45 V 3/3N AC 9.7 6 440/480 V 3 AC 7.9 6 440/480 V 3 AC 0.5 6 380-45/220-240 V 3/3N AC 7.4 6/25 380-45/220-240 V 3/3N AC 9.7 6/35 45/240 V 3/3N AC 7.9/5.5 6/25 45/240 V 3/3N AC 0.5/5.7 6/35 438 943-8/09
9:6 W330H Heating Voltage Total Fuse alternative alternative kw A No heating or Steam heating El heating 200 V 3 AC.3 0 208-240 V AC.6 0 200 V 3 AC 9.5 35 220-240 V AC 2.5 63 208-240 V 3 AC.8 35 220-240 V 3 AC 2.5 35 380-45 V 3N/3 AC 2.5 20 45 V 3N AC 2.5 25 440/480 V 3 AC 3.5 20 380-45/220-240 V 3N/3 2.5 20/35 438 943-8/09
9:7 W380H Heating Voltage Total Fuse alternative alternative kw A No heating or Steam heating El heating 200 V 3 AC 2.3 6 208-240 V AC 2.3 6 240 V AC 2.9 63 200 V 3 AC 3.4 50 220-240 V 3 AC. 50 220-240 V 3 AC 7.5 50 380-45 V 3N/3 AC 7.5 35 440/480 V 3 AC 8.9 35 380-45/220-240 V 3N/3 AC 7.5 35/50 380-45/220-240 V 3N/3 AC. 35/50 45/240 V 3N/3/ 8.9/2.9 35/63 W3240H Heating Voltage Total Fuse alternative alternative kw A No heating or Steam heating El heating 200 V 3 AC 2.6 6 208-240 V AC 2.6 6 480 V 3 AC 2.6 0 200 V 3 AC 5.5 50 240 V AC 4.3 63 220-230 V 3 AC 3.3 50 240 V 3 AC 4.3 50 208-240 V 3 AC 8.3 63 240 V 3 AC 20.9 63 380-400 V 3N/3 AC 3.3 35 380-400 V 3N/3 AC 9.4 35 45 V 3/3N AC 4.3 35 45 V 3N AC 20.9 35 440 V 3 AC 22. 35 480 V 3 AC 23.9 35 380-400/220-230 V 3N/3 9.4 35/63 45/240 V 3N/3 20.9 35/63 45/240 V 3N/3/ 20.9/4.3 35/63 438 943-8/09
9:8 W3300H Heating Voltage Total Fuse alternative alternative kw A No heating or Steam heating El heating 200 V 3 AC 2. 6 208-240 V AC 2. 0 240 V AC 4.3 63 200 V 3 AC 5.6 50 220-230 V 3 AC 9.4 63 220-230 V 3 AC 3.3 50 240 V 3 AC 4.3 50 240 V 3 AC 20.9 63 380-400 V 3N AC 3.3 35 380-400 V 3/3N AC 9.4 35 45 V 3N AC 4.3 35 45 V 3N AC 20.9 35 440 V 3 AC 22.2 35 480 V 3 AC 24 35 380-400/220-230 V 3N/3 AC 9.4 35/63 45/240 V 3N/3 20.9 35/63 45/240 V 3N/ 20.9/4.3 35/63 438 943-8/09
9:9 How to convert heating elements from 3AC to AC (400-45V 3AC to 230-240V AC) on W365H, W375H and W305H. 3 Take off isolator cover plate and front panel to expose heating elements. Remove the cables A. 3 400-45V 3AC A 5835 4 Take off wire L3 (A) from terminal L3 on isolator Q and from terminal 6 on heating relay K2. Take off wire L2 (B) from terminal L2 on isolator Q and reconnect it to terminal N (neutral) instead. The heating elements have coloured insulators on the tips, ine is red, the other is white. Connect the ends of the two wires from contactor K2 terminal to the red end of the two elements. These are your element feeds. Connect the ends of the two wires from contactor K2 terminal 3 to the white tips of the two heating elements. These are your neutral returns. Check that all your terminals and wires are secure, then test the machine on a short wash 60 C to ensure that it does heat up. Fasten isolator cover front panel to the machine. Note! The wires from terminal 5 on contactor K2 to the redundant heating element can be safely left on. 4 A B W0000 438 943-8/09
Function checks 0: Function checks, Exacta Perform the following checks once the machine is installed: Open the manual water valves. Turn on the power at the external switch. 2 Put detergent into compartment 2. Choose a high-temperature program. Press the START button. If the machine is coin-operated insert the amount of coins or tokens shown on the display. 60 2 Once the display counter shows 0, press START. Check: 524, 57 that the drum rotates normally and that there are no unusual noises. 2 that there are no leaks in water supply/drain connections. that water passes through the detergent compartment and fabric conditioner compartments. that the door cannot be opened during a program. that the machine is heating (if the machine is equipped with heating). Normal spin machine (N-model) Check: that the drum rotates clock-wise seen from the front. 534 438 944-0/0
0:2 Function checks Function checks, Clarus Control Manual operation Switch on the machine's main switch. Open the manual valves for water and for steam if the machine has steam heating. In the operating manual, chapter "Manual operation", one can find how to operate the machine manually. Check that the drum is empty and close the door. Close the drain valve. Operate the machine manually to fill with cold water, then hot water. Check that these water supplies are connected as they should be. Start the motor on wash action, and check that the motor is revolving clockwise and anticlockwise alternately, as normal for wash action. Start heating by entering a final temperature and then pressing START. Check that the steam valve opens or the heating element relay reacts, as appropriate. Check that all sources of detergent supply are working as they should, including the built-in detergent supply compartments, where present. Check the water and steam connections and the drain valve for signs of any leakages. Empty the water from the machine and open its door. 438 944-0/0
www.electrolux.com/professional Share more of our thinking at www.electrolux.com