0GU3025 2007.5 TL170SD Single Handle Lavatory Faucet Installation and Owner s Manual RENESSE English Español Français Contents Important Safeguards------------1~2 Specifications -------------------------3 Before Installation--------------------3 Set-Up Drawing -----------------------4 Components ---------------------------5 Installation Procedure ---------6~9 How to Use ---------------------------10 Maintenance --------------------11~12 Troubleshooting --------------------13 Replacement Parts------------------14 Warranty -------------------------------15 Thank you for your recent purchase of the TOTO product. Please read the enclosed information to ensure the safe use of your product..
Important Safeguards (For your safety, please follow the instructions below) Read the Important Safeguards section thoroughly before installing the product. The following symbols indicate safe and proper use of the product. Failure to observe them may reult in injury or property damage. The following table demonstrates the use of safety symbols in this manual. Warning Caution Failure to observe this symol may result in serious injury. Failure to observe this symbol may result in injury or property damage. Absolutely Do NOT. Do not disassemble Mandatory! Do Not Do not disassemble Do not Touch Warning Do not reverse the hot and cold water inlet. You may be scalded if they are reversed. Do not use hot water supply that is higher than 185 F (85 C). If water is hotter than 185 F is used, do not use steam for hot water supply. If it is broken, property damage, scalding, and other injuries may occur. Do not disassemble or modify the item in any way not described in this manual. If the system is broken, property damage, scalding and other injuries are likely to occur. While using hot water do not touch the spout and spout body directly. You may get scalded when they are hot. C Cold water HOT H Hot water Less than 185 (85 C) Ah! Do Not Caution Do not strike or kick the product If the system is broken, property damage, scalding, and other injuries may occur. Do not use the product at temperature exceding what local codes allows. If parts are damaged, property damage, scalding and other injuries may occur. Freezing 1
Mandatory Warning To use hot water, you must turn the handle on the cold side first, then turn the handle on the hot side slowly and adjust the temperature. When the valve at the hot side is opened, hot water may cause scalding. Before using hot water, check with your hand that the temperature is appropriate. When the handle on the hot side is turned, hot water may cause scalding After water is turned off, leave the handle in turned off, leave the hand in the coldside or in the middle. The next time hot water is used, the hot water remaining in the valve may cause scalding. Ah! Check water leakage and looseness in the pipe (cabinet and inspection hole etc.) regular. Do not If the system has deteriorated or worn-out, property damages, scalding and other injuries may occur. The pressure of the water supply can not be lower than that of the hot water. The hot water pressure must be lower than the pressure of the cold water side. No looseness HOT No leakage If the hot water pressure is higher than that of the cold water, you will not be able to adjust the temperature normally, and you may be scalded. Ah! Slowly 2
Specifications Cold and hot water pressure Minimum pressure Maximum pressure Maximum use temperature Suitable Water Quality Suitable ambient temperture Supply Connection Flow Rate 20psi ( 0.14MPa) (flowing pressure) 125psi (0.86MPa) (static) Less than 185 F (85 C) Water that meets National/Primary drinking water regulation 34 104 F (2 C 40 C) 3/8 NPSM Max. 2.2gpm (8.32L/min) Before installation If the water supply pressure is higher than 0.86MPa, you should buy a reducing valve to reduce the pressure to the range of 0.2-0.3MPa. To use the faucet comfortably, the recommended pressure is about 0.2-0.3MPa. To prevent being scalded due to malfunction, the water supply pressure must be higher than the hot water pressure, or you can make them equal. In addition, if you inrease the pressure of the hot water, it must still be lower than that of water supply side. To prevent being scalded due to malfunction, the recommended hot water supply temerature is 140 F. 3
Components *Observe all local plumbing codes. *Make sure that water supply is shut off. *Read these instrutions carefully to ensure proper installation. *For new lavatory installation, install the faucet before installing the lavatory. Check that you have the following parts from the package. Lever Faucet main body parts Spout mounting flange Flat washer Lock washer Outlet Push button (only for faucet with pop-up drain) Spout mounting nut Gasket Connector Assembly Flex Hose (Hot) Flex Hose (Cold) Spout Key Flat packing Gasket Winged packing Installation and Owner s Manual Some parts may be different depending on the model. 4
Set-Up Drawing *Some parts may differ from the illustration depending on the model. 5 0 HOT 5 0 COLD 5-5/16 (135mm) 6-7/16 (163mm) (OPEN) 5 (127mm) (CLOSE) 2-15/16 (75mm) 1-11/16 (43 mm) Deck Thickness Max. 1-3/16 (30 mm) 5-5/16 (135mm) 3-11/16 (94 mm) 8-9/16 (218 mm) Pop-up Drain cable connector counter hole φ 1-5/16 to 1-7/16 (φ35±2 mm) 18-3/16 (462 mm) 1-1/4 OD (32 mm OD) cable length = 13-13/16 (350 mm) 3/8 NPSM 5
Installation Procedure 2 Install the spout 3 Connect the cold/hot flex hoses 5 Pop-up drain with cable. (Only for faucet with Pop-up drain). Close 4 Pop-up Drain with Cable installation 1 Clean the cold/hot water supply pipes 1 Clean the cold/hot water supply pipes Before installation dirt and debris in the cold/ hot water supply pipes must be washed out Important 2 Install the spout. Wipe dirt away around the instllation hole. Spout Measure the installation holes, select from the two kinds of packing to suit your needs. Section Insert the packing through the cold/hot water supply hoses into the groove in the bottom of the main faucet body and into the installation hole. Insert the spout mounting flange, flat washer, lock washer and nut through the faucet mounting shaft in that order, face the spout to from the front and attach the parts. Packing Faucet mounting shaft Hot water supply hose spout mounting flange Flat washer Lock Washer Nut Faucet mounting shaft Cold Water supply hose 6
3 Connect the cold/hot water supply hoses *Put the gasket into the connectors and tighten the connectors in the stop valves; use the tool to fasten them. *Put the gasket into the cap nuts of the cold/hot flex hoses, screw in the connector, use the tool to fasten them. Flex hose (Hot) Flex hose (Cold) Cap nut Gasket Connector Gasket Stop valve 7
Cautions for installing flex hoses You have to bend the hoses, but be careful not to break them. The minimum bending radius of the hose is 2 3/8 (60mm), if you bend it over the limit, it will break, which may cause early damage. During installation, do not bend the hose from the end surface of the main faucet body too far. Do not pull the hose violently. This may break the hose. Avoid unnecessary contact of similar hoses. If the external reinforced layer of the hose is damaged due to friction, the hose performance will deteriorate. Hot water supply hose R=2 3/8 (60mm) and higher R= 2 3/8 (60mm) and higher Cold water flex hose Good Bad Bad Bad 8
4 Pop-up Drain with Cable Installation (Only for Faucet with Pop-up Drain) - Apply pipe tape to the flange threads. flange - Insert flange into the drain hole. drain body - Assemble the gasket. flange nut and lock nut. lock nut drain gasket flange nut - Apply pipe tape to the end threads of flange threads and install the tail piece to drain body -Make sure that cable faces toward the faucet. - Connect the cable base connector with cable handle connector. drain body locknut lavatory cable Push button tailpiece faucet handle cable handle connector cable base connector clip press the clip to be able to connect cable drain body pop up Push button cable handle connector groove, to which connection is to be made u-cup seal drain seal nut cable base connector clip tailpiece cable 9
How to Use How to adjust the temperature Lever Turn the lever For cold water, turn it to the right side, for hot water, turn it to the left side. If it is fully turned to the left side, the water temperature is at its highest. Left side (Hot) Right side (Cold) To prevent scalding due to malfunction, the recommended hot water supply temperature is 140 F (60 C). Open and close the Pop-up valve (Only for Faucet with Pop-up drain ) Push Push button Push the push button. When the pop-up is closed, water can be kept in the washbasin. Close Push it again, the drain is opened and water will drain out. Drain Push Push button Open Drain 10
Maintenance For best performance and sanitary environment, please maintain it everyday. Maintain the outlet Aerator Spout key Unscrew 1. Unscrew the aerator. Use attached special tool to remove it. 2. Use a brush to clear the dirt and debris from the aerator. 3. Install the aerator. Use spout key provided to install it. Aerator Be careful not to lose the parts when they are removed. Brush Use a cloth to clean it Slight dirty Use water and a damp cloth to wipe away the dirty completely. Seriously dirty Use a cloth with dilute detergent to wipe away the dirt, then wash and dry it. 11
Notes: Do not use the following materials, which are harmful to the faucet surface finish. Acidic cleaning agents, alkaline cleaning agents, bleaches except for the TOTO scale cleaner. Solvents like thinner and benzene Cleaning agents like cleanser or grinding powder that contain coarse particles Nylon scrubbers and brushes Cleaning Drain 1.For maintenance press the push button at first Push Push button pop up Unscrew Open drain body pop up Unscrew the pop up counter clockwise and take it out of the drain body Cleaning utensil such as small brush can be used to clean the pop up small brush Looseness in the main body pop up No looseness Confirm looseness in the main body If you still use it when the main body breaks loose, it will cause leakage due to the load on the pipe. In case of looseness, request for service to the installer, distributor or Tech Support. 12
Troubleshooting Before contacting a repairman, check the following common problems and solutions. If the problems perists, contact your dealer or tech support Problem Too hot Tool Cold Temperature can not be adjusted easily. Water flows without stop Flow is too small Check Is the stop valve on the cold side fully opened? Is the stop valve on the hot side fully opened? Does the water heater give enough hot water Is the stop valve on the cold/ Hot sides fully opened? Does the water heater give adequate water? Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened? Is the aerator blocked with debris? When gas water heater device is used with the product, is the switching method set properly? Is the outlet hole frozen? Solution Adjust flow with stop valve Adjust flow with stop valve Check settings and functions on the hot water device Adjust water flow with stop valve Check settings and functions on water heater with professional help Is the aerater blocked? Clean the aerator Page 9 Lower the lever handle to stop position. Use stop valve to adjust flow. Clean the aerator. Set the gas hot water device properly with professional help. Check local codes with professional help and apply hot water to the outlet. Refer to If you do not understand the position of the stop valves, ask the installer for help. You can encounter the following during use. This is not a problem P.7 P.9 Problem The handles become harder to turn than when you started to use the product. Explanation The parts of the product need breaking for a few days before they become stable. This is not a problem 13
Replacement Parts No. Description 1 Drain Assembly 2 Spout Kit 3 Set screw 4 5 Lever Valve cover 6 7 8 Cartridge aerator Spout mounting kit 9 Flex hose (Cold) 10 Flex hose (Hot) 11 Connector assembly 2 3 4 5 6 1 7 8 10 9 11 14
WARRANTY LIFETIME LIMITED WARRANTY Warranty applies to selected residential faucets only. 1. TOTO warrants its faucets ( Product ) to be free from defects in materials and workmanship during normal residential use for as long as the original consumer end-user purchaser owns their home. This limited lifetime warranty is extended only to the original consumer end-user purchaser and only so long as the Product remains in use by the original consumer end-user purchaser in its original place of installation in the purchaser s residence. This warranty applies only to Product purchased and installed in North America. 2. TOTO obligations under this warranty are limited to repair or replacement, at TOTO s option, of Product or parts found to be defective in normal residential use, provided that such Product was properly installed and used in accordance with the owner s manual. TOTO reserves the right to make such inspections as may be necessary in order to determine the cause of the defect. 3. This warranty does not apply to the following items: Damage or loss sustained in a natural calamity such as fire, earthquake, flood, thunder, electrical storm, etc. Damage or loss resulting from any accident, unreasonable use, misuse, abuse, negligence, or improper care, cleaning or maintenance of the Product. Damage or loss resulting from sediments or foreign matter contained in a water system. Damage or loss resulting from improper installation or from installation of the Product in a harsh and/or hazardous environment, or improper removal, repair or modication of the Product. Damage or loss resulting from the use of an abrasive cleanser. 4. If the Product is used commercially, TOTO warrants the Product to be free from defects in materials and workmanship for one (1) year from the date the Product is installed, with all other terms of this warranty applicable except the duration of the warranty. 5. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE. 6. To obtain warranty repair service under this warranty, you must take the Product or deliver it prepaid to a TOTO service facility with proof of purchase (original sales receipt) together with a letter stating the problem, or contact a TOTO distributor or products service contractor, or write directly to TOTO U.S.A., INC., 1155 Southern road, Morrow, Georgia 30260, (888) 295-8134. If, because of the size of the Product or nature of the defect, the Product cannot be returned to TOTO, receipt by TOTO of written notice of the defect together with proof of purchase (original sales receipt) shall constitute delivery. In such case, TOTO may choose to repair the Product at the purchaser s location or pay to transport the Product to a service facility. THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY TOTO. REPAIR, REPLACEMENT OR OTHER APPROPRIATE ADJUSTMENT AS PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE ORIGINAL PURCHASER. TOTO SHALL NOT BE RESPONSIBLE FOR LOSS OF THE PRODUCT OR FOR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY THE ORIGINAL PURCHASER, OR FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL, OR COSTS OF REPAIRS BY OTHERS, OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED. IN NO EVENT WILL TOTO S RESPONSIBILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR USE OR FOR A PARTICULAR PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU. 2007 TOTO USA, Inc. á 1155 Southern Road, Morrow GA 30260 Phone (888)-295-8134 Fax (800)-699-4889 www.totousa.com TOTO USA, INC. is a wholly owned subsidiary of TOTO Ltd. Printed in August, 2007 0GU3025