Tech Data Sheet D0170GB Fire Detection /01 AP00 SERIES INTELLIGENT ALARM DEVICES Intelligent AP00 series alarm devices for FX fire detection system The intelligent AP00 series alarm devices are used in the FX NET fire detection system. They have been designed to reduce significantly the total cost of installation. Product performance has been optimised to allow the maximum permissible number of devices to be installed on an intelligent loop. The sounders and strobes are installed in exactly the same manner as an intelligent fire detector. Both the wall-mounted and detector base devices use the B01AP detector base. At final commissioning, the sounder or strobe simply twists into the base and the installation is complete. This simple but effective concept significantly reduces the time and cost of installing audible visual warning devices when compared with previous designs. In addition, fire systems designers benefit from the flexibility of being able to change the type of installed device if the protected building is reconfigured by the occupiers. Fault finding is also easy. The suspect device is removed with a simple twist action without having to disconnect any loop wiring; a replacement is then mounted into the base. Wall mount devices Detector base devices WSO-PR-I WSO-PR-N BSO-PP-I BSO-PP-N BSS-PR-I BSS-PR-N NOTE! The products BSS-PR-I and BSS-PR-N are not approved to EN- (Visual Alarm Devices) and must not be used as a visual alarm device or to provide a primary warning notification in fire.
Tech Data Sheet D0170GB Fire Detection Mechanical dimensions Wall mount devices Detector base devices 11 11 WSO-PR-xxx BSO-PP-xxx, BSS-PR-xxx Electrical installation, Base B01AP (+) (-)1 (+) SHIELD Deep Base BPW-E010 and Waterproof Base WPW-E010 FX SLC addressable loop Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: +8 10 11
Tech Data Sheet D0170GB Fire Detection Mechanical installation Bases/IP rating Mounting Affix B01 AP base to suitably flat wall or ceiling. Terminate the cable to the appropriate terminals. For surface mount wiring the cable can enter the B01 AP base via the break outs provided. Select the appropriate tone and volume settings via the DIP switch. Locate the main assembly on to the base by rotating until it locks into place. Wall mount: B01AP Base (IP1C) Detector base mount: Deep Base BPW-E010 (IP) Waterproof Base WPW-E010 (IP) If the waterproof option is required then the wall gasket must be fitted behind the deep base, and the sealing o-ring fitted after attaching the low profile base. Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: +8 10 11
Tech Data Sheet D0170GB Fire Detection Anti tamper lock The B01 AP base also includes a tamper resistant feature that when activated prevents removal of the unit without the use of a special tool. This method is consistent with the a tamper feature across all devices using this base. This prevents the device being turned to enable its release. Wall mount: Examples: Address setting 0 7 1 0 8 10 11 1 1 1 1 x10 7 8 1 0 x1 Address setting 1 7 1 0 8 10 11 1 1 1 1 x10 7 8 1 0 x1 Detector base mount: Note! Address setting 01 is used with the FX- LC loop controller. Volume and tone setting (WSO-, BSO- and BSS-) Volume setting is selected by SW and SW7 of the 8 way DIP switch (see table 1). The appropriate tone set is selected by SW1 to of the 8 way DIP switch (see table ). The nd stage tone (related to the 1 st stage tone) is controlled by the fire panel via the protocol. Address setting The address setting in the devices is simply done with two rotary decimal switches, thus having a range of 1 1. In addition the panel can distinguish between detector addresses, I/O-module addresses and sounder addresses, and thus providing a total address capacity per loop of 001 1 and 01, altogether 18 addresses. Two rotary switches are located either side of the dip switch unit. Table 1 7 8 1 0 10 11 1 1 1 x10 SW SW7 Volume setting OFF OFF High OFF ON Medium ON OFF Low ON ON Low OFF = 0, ON = 1 1 ON ON 1 7 8 1 8 Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: +8 10 11
Tech Data Sheet D0170GB Fire Detection Table DIP setting O=Off/1=On SW 1,,,, No Pattern Nominal Frequency Switching Frequency Description Standard 0,0,0,0,0 1 Alternating /0 Hz French Fire Sound (100ms/00ms) AFNOR NFS -001 7 1,0,0,0,0 Alternating 800/70 1Hz BS8 Pt1 8 0,1,0,0,0 Alternating 800/70 Hz Alternating tone BS8 Pt1 telecoms FP10.1 8 1,1,0,0,0 Alternating 00/00 Hz Alternating High Frquency 10 0,0,1,0,0 Alternating 00/100 Hz Security Alarm 10 1,0,1,0,0 Alternating 88/ Hz 8 0,1,1,0,0 7 Continuous 0 All Clear 1 1,1,1,0,0 8 Continuous 70 BS8 Pt1 0,0,0,1,0 Continuous 100 1,0,0,1,0 10 Continuous 80 HF Continuous 0,1,0,1,0 11 Sweep 00-1000 Raising from 10Hz to 1000Hz in 10 seconds, then 0 seconds at 1000Hz, then falling from 1000Hz to 10Hz in 10 seconds, then 0 seconds at 10 Hz, then repeating. Total period 80 seconds. Gasalarm Tone 1,1,0,1,0 1 Intermittent 0 0.s on,0.s off AS0 alert tone AS0 1 0,0,1,1,0 1 Sweep 00-100 0.s off,.7s off AS0 evacuate tone AS0 1 1,0,1,1,0 1 Intermittent 0.Hz 10ms on, 10ms off Swedish Alarm Tone 7 0,1,1,1,0 1 Intermittent 70 0.8Hz 0.s on, 1s off Intermittent Tone BS8 Pt1 8 1,1,1,1,0 1 Intermittent 70 0.Hz 1s on, Backup alarm LF & 1s off BS8 Pt1 BS8 Pt1 8 0,0,0,0,1 17 Intermittent 80 1Hz Backup alarm HF & BS8 Pt1 nd Tone BS8 Pt1 10 1,0,0,0,1 18 Intermittent 70 1Hz 00ms on, 00ms off BS8 Pt1 BS8 Pt1 8 0,1,0,0,1 1 Intermittent 0 0.Hz (0.s on, 0.s off)*, 1.s off ISO801 1 1,1,0,0,1 0 Continuous 800 Hz 10ms on, 100ms off BS8 Pt1 0,0,1,0,1 1 Sweep 00-100 (0.s on, 0.s off)*, Temporal ISO801 1.s off Evacuation tone Temporal 1 1,0,1,0,1 Sweep 100-00 0.Hz 1s on, Evacuate, DIN tone & 0.01s off PFEER DIN, PFEER 0 0,1,1,0,1 Sweep 00-80 7Hz Fast Sweep Vds Vds 10 1,1,1,0,1 Sweep 00-100 0.sec off.sec on Slow whoop evacuate Netherlands NEN 7 8 0,0,0,1,1 Sweep 800-70 0Hz LF buzz BS8 Pt1 BS8 Pt1 8 1,0,0,1,1 Sweep 800-70 7Hz Fast sweep LF BS8 Pt1 BS8 Pt1 8 0,1,0,1,1 7 Sweep 800-70 1Hz Medium sweep LF buzz BS8 Pt1, BS8 Pt1 VdS 8 Vds 1,1,0,1,1 8 Sweep 00-80 0Hz High frequency buzz 10 0,0,1,1,1 Sweep 00-1000 7Hz Fast whoop 8 1,0,1,1,1 0 Sweep 00-100 - 0.1 Hz rise 1 s, 00 stable s, fall 1s Siren style tone 8 0,1,1,1,1 1 Sweep 800-1000 Hz 8 1,1,1,1,1 Sweep 00-80 1Hz 10 nd Stage Tone Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: +8 10 11
Tech Data Sheet D0170GB Fire Detection Table Typical current consumption DIP setting O=Off/1=On No Wall mount devises Detector base mount devises SW 1,,,, (WSO) (WSO) (WSO) (BSO/BSS) (BSO/BSS) (BSO/BSS) High Medium Low High Medium Low 0,0,0,0,0 1.0/../.8 1./../.7./. 1.1/. 1,0,0,0,0./8.7./. 1./.7./7.8.0/. 1./. 0,1,0,0,0./8..8/.1 1./.7./7.7.0/. 1./. 1,1,0,0,0./8../. 1.7/.0./7..1/. 1./.8 0,0,1,0,0.7/10.0./. 1.8/.1./8../. 1./. 1,0,1,0,0./../.8 1./.7.0/8../. 1./. 0,1,1,0,0 7.0/8../.8 1./.7.8/8.1./. 1.1/. 1,1,1,0,0 8.8/8.1./. 1./.7./7.8 1./. 1./. 0,0,0,1,0.8/8.1./. 1./.8./7.8.0/. 1./. 1,0,0,1,0 10./8..7/.0 1./.8./7.8.1/. 1./.7 0,1,0,1,0 11./8.8./.8 1./.7.0/8..1/. 1./.7 1,1,0,1,0 1./../. 1.1/../8..1/. 1.0/. 0,0,1,1,0 1 10./1.7./. 1.7/.0.1/1..0/. 1./. 1,0,1,1,0 1.0/8../.7 1./..7/8.0./. 1.1/. 0,1,1,1,0 1.8/8.1./. 1./.7./7.7 1./. 1./. 1,1,1,1,0 1.8/8.1./. 1./.7.8/8.1 1./. 1./. 0,0,0,0,1 17./8..7/.0 1./.8./7.8.1/. 1./.7 1,0,0,0,1 18.8/8.1./. 1./.7./7.8 1./. 1./. 0,1,0,0,1 1./7..1/. 1./../7.7 1./. 1./. 1,1,0,0,1 0./8../. 1./../7..0/. 1./. 0,0,1,0,1 1 11.1/1..1/. 1./. 10./1.8./.8 1./. 1,0,1,0,1 10./1../. 1.7/.0./1..8/.1 1./. 0,1,1,0,1.0/8../. 1./..8/8.1./.7 1.7/.0 1,1,1,0,1 10./1../.8 1.7/.0.0/1..0/. 1./. 0,0,0,1,1.0/7../. 1./..7/7.0 1./. 1./. 1,0,0,1,1./7.8./.8 1./.7./7..0/. 1./. 0,1,0,1,1 7.1/8..8/.1 1./.7./7..0/. 1./.7 1,1,0,1,1 8./8../. 1.8/.1./7../.7 1./. 0,0,1,1,1./8.7./.8 1./..8/8.1 1./. 1./. 1,0,1,1,1 0 10.1/1../.7 1.7/.0./1..8/.1 1./. 0,1,1,1,1 1./8..7/.0 1./.7.8/8.1.1/. 1./.7 1,1,1,1,1./8../. 1./..0/8../.7 1./. Note! For Isolated variants add 0.1mA to high, medium, low values above. Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: +8 10 11
Tech Data Sheet D0170GB Fire Detection 7 Technical data Wall Mount Devices WSO-PR-xxx Description Sounder Operating voltage 1 to VDC(isolation) (VDC typical) 1 to VDC (non isolation) (VDC typical) Quiescent current 0µA Max current consumption (sound) (isolation).77ma (High Volume Tone 8@ V) Max current consumption (sound) (non isolation).8ma (High Volume Tone 8@ V) Sound Output to EN- db(a)±db (High Volume Tone 8@ V) Operating Temperature - to 70 C Relative Humidity Up to % (±%) non-condensing IP Rating IPC (with B01 AP base) IP (with Deep base BPW-E010) IP (with Waterproof base WPW-E010) Colour Red Weight 7g Terminal Size max.mm Number of Tones Volume Setting High, Medium, Low Product codes WSO-PR-I, isolation FFS071177 WSO-PR-N, non isolation FFS071178 Bases IP rating Product codes B01AP IP1 FFS071000 BPW-E010 IP FFS07117 WPW-E010 IP FFS07117 Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: +8 10 11
Tech Data Sheet D0170GB Fire Detection 8 Detector Base Mount Devises BSO-PP-xxx BSS-PR-xxx Description Sounder Sounder Strobe Operating voltage 1 to VDC (non isolation) (VDC typical) 1 to VDC (isolation) (VDC typical) Quiescent current 0µA Max current consumption (sound).7ma 8.0mA (isolation) (High Volume Tone 8@ V) Max current consumption (sound) (non isolation) (High Volume Tone 8@ V).mA 7.8mA Sound Output to EN- db(a)±db (High Volume Tone 8@ V) Beacon Flash Rate N/A 1 Hz Operating Temperature - to 70 C Relative Humidity Up to % (±%) non-condensing IP Rating IPC (with B01 AP base) IP (with Deep base BPW-E10) IP (with Waterproof base WPW-E10) Colour White Weight 1g 00g Lens Colour Red Terminal Size max.mm Number of Tones Volume Setting High, Medium, Low Product codes BSO-PP-I, isolation BSO-PP-N, non isolation FFS071171 FFS07117 BSS-PR-I, isolation BSS-PR-N, non isolation FFS07117 FFS07117 NOTE! The products BSS-PR-I and BSS-PR-N are not approved to EN- (Visual Alarm Devices) and must not be used as a visual alarm device or to provide a primary warning notification in fire. Bases IP rating Product codes B01AP IP1 FFS071000 BPW-E010 IP FFS07117 WPW-E010 IP FFS07117 Schneider Electric Fire & Security Oy Sokerilinnantie 11 C, 000 Espoo, Finland Telephone: +8 10 11