Dit document mag slechts op een stand-alone PC worden geinstalleerd. Gebruik op een netwerk is alleen. toestaan als een aanvullende licentieovereenkomst voor netwerkgebruik met NEN is afgesloten. This document may only be used on a stand-alone PC. Use in a network is only permitted when a supplementary license agreement for us in a network with NEN has been concluded. Nederlandse norm NEN-EN-IEC 61753-091-2 (en) Fibre optic interconnecting devices and passive components - Performance standard - Part 091-2: Non-connectorized single-mode fibre optic pigtailed circulators for category C - Controlled environment (IEC 61753-091-2:2012,IDT) ICS 33.180.20 januari 2013
NEN-EN-IEC 61753-091-2 Als Nederlandse norm is aanvaard: - EN 61753-091-2:2013,IDT - IEC 61753-091-2:2012,IDT Nederlands Elektrotechnisch Comité THIS PUBLICATION IS COPYRIGHT PROTECTED DEZE PUBLICATIE IS AUTEURSRECHTELIJK BESCHERMD Apart from exceptions provided by the law, nothing from this publication may be duplicated and/or published by means of photocopy, microfilm, storage in computer files or otherwise, which also applies to full or partial processing, without the written consent of the Netherlands Standardization Institute. The Netherlands Standardization Institute shall, with the exclusion of any other beneficiary, collect payments owed by third parties for duplication and/or act in and out of law, where this authority is not transferred or falls by right to the Reproduction Rights Foundation. Auteursrecht voorbehouden. Behoudens uitzondering door de wet gesteld mag zonder schriftelijke toestemming van het Nederlands Normalisatie-instituut niets uit deze uitgave worden verveelvoudigd en/of openbaar gemaakt door middel van fotokopie, microfilm, opslag in computerbestanden of anderszins, hetgeen ook van toepassing is op gehele of gedeeltelijke bewerking. Het Nederlands Normalisatie-instituut is met uitsluiting van ieder ander gerechtigd de door derden verschuldigde vergoedingen voor verveelvoudiging te innen en/of daartoe in en buiten rechte op te treden, voor zover deze bevoegdheid niet is overgedragen c.q. rechtens toekomt aan de Stichting Reprorecht. Although the utmost care has been taken with this publication, errors and omissions cannot be entirely excluded. The Netherlands Standardization Institute and/or the members of the committees therefore accept no liability, not even for direct or indirect damage, occurring due to or in relation with the application of publications issued by the Netherlands Standardization Institute. Hoewel bij deze uitgave de uiterste zorg is nagestreefd, kunnen fouten en onvolledigheden niet geheel worden uitgesloten. Het Nederlands Normalisatie-instituut en/of de leden van de commissies aanvaarden derhalve geen enkele aansprakelijkheid, ook niet voor directe of indirecte schade, ontstaan door of verband houdend met toepassing van door het Nederlands Normalisatie-instituut gepubliceerde uitgaven. 2013 Nederlands Normalisatie-instituut Postbus 5059, 2600 GB Delft Telefoon (015) 2 690 390, Fax (015) 2 690 190
NEN-EN-IEC 61753-091-2 Nederlands voorwoord Voor de in deze norm vermelde normatieve verwijzingen bestaan in Nederland de volgende equivalenten: vermelde norm Nederlandse norm titel IEC 60793-2-50:2008 NEN-EN-IEC 60793-2- 50:2008 Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres IEC 60794-2-50 NEN-EN-IEC 60794-2-50 Optical fibre cables - Part 2-50: Indoor cables - Family specification for simplex and duplex cables for use in terminated cable assemblies IEC 61300-2-1 NEN-EN-IEC 61300-2-1 Fibre optic interconnecting devices and passive procedures - Part 2-1: Tests - Vibration (sinusoidal) IEC 61300-2-4 NEN-EN-IEC 61300-2-4 Optische-vezelverbindingselementen en passieve componenten - Basisbeproevings en - meetprocedures - Deel 2-4: Beproevingen - Retentie van de vezel/kabel IEC 61300-2-9 NEN-EN-IEC 61300-2-9 Fibre optic interconnecting devices and passive procedures - Part 2-9: Tests - Shock IEC 61300-2-14 NEN-EN-IEC 61300-2-14 Fibre optic interconnecting devices and passive procedures - Part 2-14: Tests - Optical power handling and damage threshold characterization IEC 61300-2-19 NEN-EN-IEC 61300-2-19 Fibre optic interconnecting devices and passive procedures - Part 2-19: Tests - Damp heat (steady state) IEC 61300-2-22 NEN-EN-IEC 61300-2-22 Fibre optic interconnecting devices and passive procedures - Part 2-22: Tests - Change of temperature IEC 61300-2-42 NEN-EN-IEC 61300-2-42 Fibre optic interconnecting devices and passive procedures - Part 2-42: Tests - Static side load for connectors IEC 61300-2-44 NEN-EN-IEC 61300-2-44 Fibre optic interconnecting devices and passive procedures - Part 2-44: Tests - Flexing of the strain relief of fibre optic devices IEC 61300-3-2 NEN-EN-IEC 61300-3-2 Fibre optic interconnecting devices and passive procedures - Part 3-2: Examinations and measurements - Polarization dependent loss in a single-mode fibre optic device IEC 61300-3-7 NEN-EN-IEC 61300-3-7 Fibre optic interconnecting devices and passive procedures - Part 3-7: Examinations and measurements - Wavelength dependence of attenuation and return loss of single mode components IEC 61300-3-28 NEN-EN-IEC 61300-3-28 Fibre optic interconnecting devices and passive procedures - Part 3-28: Examinations and measurements - Transient loss IEC 61300-3-32 NEN-EN-IEC 61300-3-32 Fibre optic interconnecting devices and passive procedures - Part 3-32: Examinations and measurements - Polarization mode dispersion measurement for passive optical components
EUROPEAN STANDARD EN 61753-091-2 NORME EUROPÉENNE EUROPÄISCHE NORM January 2013 ICS 33.180.20 NEN-EN-IEC 61753-091-2:2013 English version Fibre optic interconnecting devices and passive components - Performance standard - Part 091-2: Non-connectorized single-mode fibre optic pigtailed circulators for category C - Controlled environment (IEC 61753-091-2:2012) Dispositifs d'interconnexion et composants passifs à fibres optiques - Norme de performance - Partie 091-2: Circulateurs à fibres optiques unimodales munis de fibres amorces non connectorisées pour la catégorie C - Environnements contrôlés (CEI 61753-091-2:2012) Lichtwellenleiter - Verbindungselemente und passive Bauteile - Betriebsverhalten - Teil 091-2: Nicht mit Steckverbindern versehene Einmoden-Lichtwellenleiter- Zirkulatoren mit Pigtails der Kategorie C - Kontrollierte Umgebung (IEC 61753-091-2:2012) This European Standard was approved by CENELEC on 2012-11-16. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61753-091-2:2013 E
NEN-EN-IEC 61753-091-2:2013 EN 61753-091-2:2013-2 - Foreword The text of document 86B/3364/CDV, future edition 1 of IEC 61753-091-2, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61753-091-2:2013. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement latest date by which the national standards conflicting with the document have to be withdrawn (dop) 2013-08-16 (dow) 2015-11-16 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61753-091-2:2012 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61300-3-38 NOTE Harmonized as EN 61300-3-38. IEC 61753-1 NOTE Harmonized as EN 61753-1. IEC 62077 NOTE Harmonized as EN 62077.
NEN-EN-IEC 61753-091-2:2013-3 - EN 61753-091-2:2013 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60793-2-50 2008 Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres EN 60793-2-50 2008 IEC 60794-2-50 - Optical fibre cables - Part 2-50: Indoor cables - Family specification for simplex and duplex cables for use in terminated cable assemblies EN 60794-2-50 - IEC 61300-2-1 - Fibre optic interconnecting devices and Part 2-1: Tests - Vibration (sinusoidal) IEC 61300-2-4 - Fibre optic interconnecting devices and Part 2-4: Tests - Fibre/cable retention IEC 61300-2-9 - Fibre optic interconnecting devices and Part 2-9: Tests - Shock IEC 61300-2-14 - Fibre optic interconnecting devices and Part 2-14: Tests - High optical power IEC 61300-2-19 - Fibre optic interconnecting devices and Part 2-19: Tests - Damp heat (steady state) IEC 61300-2-22 - Fibre optic interconnecting devices and Part 2-22: Tests - Change of temperature IEC 61300-2-42 - Fibre optic interconnecting devices and Part 2-42: Tests - Static side load for connectors EN 61300-2-1 - EN 61300-2-4 - EN 61300-2-9 - EN 61300-2-14 - EN 61300-2-19 - EN 61300-2-22 - EN 61300-2-42 - IEC 61300-2-44 - Fibre optic interconnecting devices and Part 2-44: Tests - Flexing of the strain relief of fibre optic devices EN 61300-2-44 -
NEN-EN-IEC 61753-091-2:2013 EN 61753-091-2:2013-4 - Publication Year Title EN/HD Year IEC 61300-3-2 - Fibre optic interconnecting devices and Part 3-2: Examinations and measurements - Polarization dependent loss in a single-mode fibre optic device IEC 61300-3-7 - Fibre optic interconnecting devices and Part 3-7: Examinations and measurements - Wavelength dependence of attenuation and return loss of single mode components EN 61300-3-2 - EN 61300-3-7 - IEC 61300-3-28 - Fibre optic interconnecting devices and Part 3-28: Examinations and measurements - Transient loss EN 61300-3-28 - IEC 61300-3-32 - Fibre optic interconnecting devices and Part 3-32: Examinations and measurements - Polarisation mode dispersion measurement for passive optical components EN 61300-3-32 -
NEN-EN-IEC 61753-091-2:2013 INTERNATIONAL STANDARD NORME INTERNATIONALE IEC 61753-091-2 Edition 1.0 2012-10 Fibre optic interconnecting devices and passive components Performance standard Part 091-2: Non-connectorized single-mode fibre optic pigtailed circulators for category C Controlled environments Dispositifs d'interconnexion et composants passifs à fibres optiques Norme de performance Partie 091-2: Circulateurs à fibres optiques unimodales munis de fibres amorces non connectorisées pour la catégorie C Environnements contrôlés IEC 61753-091-2:2012
Bestelformulier Stuur naar: NEN Standards Products & Services t.a.v. afdeling Klantenservice Antwoordnummer 10214 2600 WB Delft NEN Standards Products & Services Postbus 5059 2600 GB Delft Vlinderweg 6 2623 AX Delft Ja, ik bestel ex. NEN-EN-IEC 61753-091-2:2013 en Fibre optic interconnecting devices and passive components - Performance standard - Part 091-2: Nonconnectorized single-mode fibre optic pigtailed circulators for category C - Controlled environment 64.30 T (015) 2 690 390 F (015) 2 690 271 www.nen.nl/normshop Wilt u deze norm in PDF-formaat? Deze bestelt u eenvoudig via www.nen.nl/normshop Gratis e-mailnieuwsbrieven Wilt u op de hoogte blijven van de laatste ontwikkelingen op het gebied van normen, normalisatie en regelgeving? Neem dan een gratis abonnement op een van onze e-mailnieuwsbrieven. www.nen.nl/nieuwsbrieven Gegevens Bedrijf / Instelling T.a.v. O M O V E-mail Klantnummer NEN Uw ordernummer BTW nummer Postbus / Adres Postcode Plaats Telefoon Fax Factuuradres (indien dit afwijkt van bovenstaand adres) Postbus / Adres Postcode Plaats Datum Handtekening Retourneren Fax: 015 2 690 271 E-mail: klantenservice@nen.nl Post: NEN Standards Products & Services, t.a.v. afdeling Klantenservice Antwoordnummer 10214, 2600 WB Delft (geen postzegel nodig). Voorwaarden De prijzen zijn geldig tot 31 december 2018, tenzij anders aangegeven. Alle prijzen zijn excl. btw, verzend- en handelingskosten en onder voorbehoud bij o.m. ISO- en IEC-normen. Bestelt u via de normshop een pdf, dan betaalt u geen handeling en verzendkosten. Meer informatie: telefoon 015 2 690 391, dagelijks van 8.30 tot 17.00 uur. Wijzigingen en typefouten in teksten en prijsinformatie voorbehouden. U kunt onze algemene voorwaarden terugvinden op: www.nen.nl/leveringsvoorwaarden. LEREN, WERKEN EN GROEIEN MET NEN preview - 2018