FAQ & INSTALLATION MANUAL 08. Maintenance & care. Materials & finishes 3. To place an order 4. Returns 5. How to suspend the light?. Cord and ceiling connection 7. Colour options of the cord 8. Touch dimmer button 9. External dimming system 0. Divar wall lamp. Warranty. Dammages 3. Not responsible for the following 4. Notes
. MAINTENANCE & CARE. MATERIALS & FINISHES CARE AND MAINTENANCE To maintain the finished quality of your ANOUR product, please follow the cleaning procedures provided below. The instructions for the care and maintenance are provided to you as a service. No warranty is implied since results may vary. Before cleaning, the light must be turned off and unplugged from mains supply. Whilst cleaning, please be extremely careful. POLISHED COPPER BRUSHED COPPER POLISHED BRASS BRUSHED BRASS MAINTENANCE AND CARE OF POLISHED SURFACE The product should only be treated with a polishing cream made for the specific material. We recommend BRASSO BROWNED COPPER BROWNED BRASS MAINTENANCE AND CARE OF BROWNED SURFACE & BLUED STEEL The product should only be cleaned with a dry soft cloth. Only if required, a thin coat of acid free natural oil can be applied on the surface and wiped afterwards with a clean soft cloth. OXIDISED COPPER BLACK ALUMINIUM MAINTENANCE AND CARE OF BRUSHED SURFACE For regular cleaning, the product should only be cleaned with a dry soft cloth. To remove small scratches and scuff marks, you can firmly rub the surface (in the same direction of the brushed finish) with the rough green side of a sponge. RUSTED STEEL OAK MAINTENANCE AND CARE OF RUSTED AND OXIDISED SURFACE For regular cleaning, please use a feather duster. BLUED STEEL BLACK STAIN OAK MAINTENANCE AND CARE OF MARBLE Dust frequently with a clean, soft cloth. Wash periodically with a cloth dampened with warm water, and if necessary, a small amount of mild dishwashing liquid. Use a second damp cloth to remove the soap. CARRARA MARBLE WALNUT Please be careful with liquids around the touch dimmer and cable insulation areas. For more information, consult the FAQ on anour.dk or contact us at contact@anour.dk Anour finishes are created in our Copenhagen workshop by our artisans. Our raw materials copper, brass, steel and wood have an innate character and a corresponding ageing process. Due to the handmade process, each product is unique and may vary in finish. 3
3. TO PLACE AN ORDER. CORD & CEILING CONNECTION Please visit our website www.anour.dk to place an order. Orders are subject to payment in full with order. Transport cost is included within the EU. Goods will be ready to ship with a lead time of 8 weeks. Lead time starts when we have received payment in full. Queries can be sent to contact@anour.dk OPTION : The cord goes directly through a hole to the ceiling. Recommended for suspended ceiling panels Ceiling 4. RETURNS Cord Because all products are handmade and made to order, we cannot accept returns. 5. HOW TO SUSPEND THE LIGHT? Above a table top, we recommend leaving a distance of 0 70 cm between the top of the table and the bottom edge of the pendant. Between the side edge of the table and the side edge of the lamp, we recommend leaving 30 50 cm. Above a kitchen island, a little more space will be needed. We recommend 70 85 cm between the worktop of the island and the bottom edge of the pendant. Please make sure the hanging height of the light is to your satisfaction before cutting the wire/cord. Lamp OPTION : Use cord clips to direct the connection away from the ceiling suspension towards the nearest electrical output. Ceiling Lamp 7. COLOUR OPTIONS OF THE CORD Table 0 50cm 0 70cm The suspension wire is always in steel, but the textile cord of the light is available in several colours. Unless otherwise stipulated, we will supply the light with our standard colour combination. Standard combinations: Brass, brushed Grey cord Brass, polished Grey or black cord Brass, browned Brown cord Copper, brushed Copper cord Copper, Polished Copper cord Copper, browned Brown cord 0 50cm Steel, rusted Brown cord Steel blued Grey or black cord 70 85cm Kitchen Island Black Grey Brown Copper 4 5
Note: Please advise us if you request a cord longer than the 3 metres standard length. DIVAR (50 50cm) Only white cord DIVAR (00 cm) Only black cord. WARRANTY The warranty period is years for Denmark and year for other EU and noneu countries. 8. TOUCH DIMMER BUTTON. DAMMAGES Damages on delivery must be documented and reported within 5 working days of receipt. ANOUR will not be responsible for any repair or replacement of damaged goods reported after this time. If damage has occured during shipment, all packaging must be retained and the goods must be signed for either as damaged or not checked. Failure to do so may invalidate any claim. 9. EXTERNAL DIMMING SYSTEM Tap once to switch on. Tap again to switch off. Double tap to reach max/min light. Maintain your finger on the button to dim the light. RECEPTION OF THE LIGHT // CLAIM PROCESS. Check for any visible damage to the packaging. If yes, report it immidiately to the delivery man and on your shipping receipt.. Open the package and check the contents. 3. If there is any visible damage to the product, please document and notify us immediately with photos and your order number. Our lights feature an integrated touch dimmer button that does not function with an external dimmer. If an external dimming option is required we can supply our lights DALI or 0 Volt compatible at an additional charge. However, we recommend that you consult your electrician first. Please note, we do not supply the system or switch for your installation. 0. DIVAR LAMP 3. NOT RESPONSIBLE FOR THE FOLLOWING Damage caused by incorrect cleaning solutions or methods. Damage caused by incorrect installation or assembly by the customer or the customer s agent. Damage caused by exposure to weather and poor environment. Changes in the appearance of the finishes designed to change with age. Any cost of installation, removal or reinstallation. Restoration or repair work. Any parts purchased from other suppliers, for our light fixtures. The DIVAR wall lamp comes standard with m cord and a plug in power supply (EU or UK). 4. NOTES There is no ceiling cap provided with the IMODEL. Power supply EU / UK Please note that we currently only offer lights to the US without power supply. We advise you to purchase the switchex system from diodeled directly. This is an UL certified external dimmer/driver from a renowned US company. Link: http://www. diodeled.com/switchex/ 7
. DIVAR MODEL DIMENSIONS INSTALLATION MANUAL 08 5, kg 500 500. DIVAR 4. X MODEL 5, kg. I MODEL 5. G MODEL 400 000 3. Y MODEL. U MODEL 5 3,3 kg 900 500 IMPORTANT. Read our instructions before installing and using the product 5 4, kg If you have any problems with the electrical installation, contact an electrician. Be sure to turn off the power before you start the installation. In some countries, all electrical installation must be carried out by professional electricians only. For further information, contact the relevant authorities. 400 000 5 5, kg Our products are for indoor use only. Check on a regular basis that the cord and other parts are not damaged. In this case, the product must not be used. Save these instructions for future use. We use LED as a light source for our products. For replacement of LED contact Anour. The product should not be dismantled as it may get damaged. The product should not come into direct contact with water. 950 00 500 0 950 00 5, kg Our products are marked with the symbol of the crossed out wheelie bin. That means that the product should not be disposed of with other household waste. Our products must be recycled in accordance with local environmental regulations for the disposal of waste. In complying with this you will help to minimize any adverse effect on human and environmental health. If you have any questions please contact Anour. x3* x3* x3* x3* x3* Power supply EU / UK Note: There is no ceiling cap provided with the IModel lamp. 3mm Ø mm STANDARD CONFIGURATION The DIVAR wall lamp comes standard with m cord and a plug in power supply (EU or UK). Then you have also different options to integrate the driver in the wall and have DALI or 0v dimming system. Please see page 0. 8 9
. DIVAR MODEL. DIVAR MODEL INSTALLATION INSTRUCTIONS INTEGRATION AND DIMMING SYSTEM OPTION : Touch dimmer CORD DRIVER: 74 x 5 x 30 mm CORD / 0 meters TOUCH DIMMER BUTTON 30 V 3 4 OPTION : 0V x cm* ~ 50 mm. CORD DRIVER: 74 x 5 x 30 mm 5 DK Stram kun møtrikken forsigtigt efterlad ca. mm. DK Hurtigt tryk på lysdæmperen < 3 sek = Tænd/Sluk. Tryk og hold på lysdæmperen > 3 sek = dæmp/forøg. CORD / 0 meters Plug the Power supply EU / UK EN Tighten the bolt gently Leave approximately mm. IMPORTANT! EN Quick tap on the light dimmer hold on the light dimmer > 3 sec = brighten /dim. 0 V 30 V OPTION 3: DALI STANDARD CONFIGURATION The DIVAR wall lamp comes standard with m cord and a plug in power supply (EU or UK). Then you have also different options to integrate the driver in the wall and have DALI or 0v dimming system. Please see page 0. CORD CORD / 0 meters DALI DIMBox 87 x 5 x 30 mm DRIVER: 74x5x30mm 30 V 0
. I MODEL WITH CORD DIMENSIONS. I MODEL WITH CORD INSTALLATION INSTRUCTIONS 00 cm 3 cm 54 cm 3 cm 5, cm 3,5 cm 3,3 kg DK Se punkt 9 for opmåling See point 9 EN for measurements 3 4 50 cm 33 cm 84 cm 33 cm 5, cm 3,5 cm 5 kg 5 7 8 00 cm 38 cm 4 cm 38 cm 5, cm 3,5 cm,5 kg 50 cm 5, cm 3,5 cm 48 cm 54 cm 48 cm cm 48 cm 04 cm 48 cm 8 kg 5, cm 3,5 cm 0 kg 9 0 Se side for mål See page for dimensions Ca./approx. 5 cm OFF / SLUKKET L N 3 4 5 ON / TÆNDT Ø 4, Ø 5,5 7 DK x x x3 x x x EN DK EN Brug for hjælp? Ring til os: 45 9 99 79 Need help? Please call us: 45 9 99 79 Ø 5,5 () mm 3
I MODEL CORDLESS Installation manual 8 Please, read our instructions before installing and using the product. 7 9 If you have any problems with the electrical installation, contact an electrician. Be sure to turn off the power before you start the installation. In some countries, all electrical installation must be carried out by professional electricians only. For further information, contact the relevant authorities. Our products are for indoor use only. Check on a regular basis that the cord and other parts are not damaged. In this case, the product must not be used. Save these instructions for future use. We use LED as a light source for our products. For replacement of LED contact Anour. The product should not be dismantled as it may get damaged. The product should not come into direct contact with water. Our products are marked with the symbol of the crossed out wheelie bin. That means that the product should not be disposed of with other household waste. Our products must be recycled in accordance with local environmental regulations for the disposal of waste. In complying with this you will help to minimize any adverse effect on human and environmental health. If you have any questions please contact Anour. contact@anour.dk (07) Positive pole 4 0 Button 5 Negative pole cross the steel wires 3 30V. Measure distance between the suspension points. See below.. Drill holes and fasten the plastic ceiling components. 3. Position the driver box (see diagram below), drill holes and fasten it. 4. Attach the wires to the nipples and tightly fasten the wires to the lamp. The positive pole is the suspension point closest to the button. 5. Insert the steel wires in the plastic ceiling components. Assure that the wires are aligned. cross the steel wires.. Insert the wire in the terminal and the wire in the terminal. You can change the position of the poles by repositioning the wire gripers. 7. Adjust the height of the lamp by pressing the wire griper and then, cut the excess wire, as shown. We recommend suspending the light with a distance of / 0cm above a dinning table. For kitchen table tops, we recommend / 70cm. 8. Connect the primary power cable to the terminals on the primary side of the power supply and then, fasten the screw of the safety cap. Should be performed according to safety regulations. 9. Cut out one input for the primary power cable (3 options shown) in the plastic lid and then attach the lid to the power supply (magnetic closure). 0. On / Off / Dimming. Quick tap on the button on the lamp = On/Off. Hold finger on the button = brighten or dim. Double tap: for max or min brightness If the button does not respond, turn off main power for the duration of 30 sec and try again. DIMENSIONS DRIVER BOX POSITION OPTIONS : DIAGRAM (TOP VIEW) EQUIPMENT 3,3 kg 3 cm 54 cm 3 cm 00 cm Ø 4, Ø 5,5 33 cm 84 cm 33 cm 50 cm 5 kg 38 cm 4 cm 38 cm 00 cm,5 kg x 8m x Driver box: 340x3,5x3 mm (LxWxH) 48 cm 54 cm 48 cm 50 cm 8 kg Suspension point Ø 5,5 () mm 48 cm 04 cm 48 cm cm 0 kg Driver box Lamp Wire 4 5
Y MODEL CORDLESS 5 Installation manual Please, read our instructions before installing and using the product. cross the steel wires 4 If you have any problems with the electrical installation, contact an electrician. Be sure to turn off the power before you start the installation. In some countries, all electrical installation must be carried out by professional electricians only. For further information, contact the relevant authorities. 7 Our products are for indoor use only. Check on a regular basis that the cord and other parts are not damaged. In this case, the product must not be used. Save these instructions for future use. We use LED as a light source for our products. For replacement of LED contact Anour. The product should not be dismantled as it may get damaged. The product should not come into direct contact with water. Our products are marked with the symbol of the crossed out wheelie bin. That means that the product should not be disposed of with other household waste. Our products must be recycled in accordance with local environmental regulations for the disposal of waste. In complying with this you will help to minimize any adverse effect on human and environmental health. If you have any questions please contact Anour. contact@anour.dk (07) 8 3 EQUIPMENT Ø 4, Ø 5,5 x3 Driver box: ø75 x 30 mm Ø 5,5 () mm. Position & measurement.. Drill 3 holes, place the anchors and fasten the ceiling bracket. 3. Attach the wires to the nipples and tightly fasten the wires to the lamp. The positive pole is the suspension point closest to the touch button. 4. Insert the 3 wires through the holes of the rosette cover 5. Insert the 3 wires in the 3 wire grippers. Follow the color code to Insert the wires in the terminals and the wires in the terminals. DIAGRAM 30V Touch button 0 0 400. Connect the primary power cable to the terminals on the primary side of the power supply and then, fasten the screw of the safety cap. 7. Close the box / Magnetic closure 8. On / Off / Dimming. Tap on the button on the lamp: less than 3 sec = On/Off. Touch the button: more than 3 sec = brighten or dim. Double tap: for max or min brightness Should be performed according to safety regulations. If the button does not respond, turn off main ø80 = 4,5 kg power for the duration of 7 30 sec and try again. 80 5. Adjust the position of the lamp and then cut the excess of wire. We recommend suspending the light with a distance of / 0cm above a dinning table.
X MODEL CORDLESS 5 Installation manual cross the steel wires Please, read our instructions before installing and using the product. If you have any problems with the electrical installation, contact an electrician. Be sure to turn off the power before you start the installation. In some countries, all electrical installation must be carried out by professional electricians only. For further information, contact the relevant authorities. 4 7 Our products are for indoor use only. Check on a regular basis that the cord and other parts are not damaged. In this case, the product must not be used. Save these instructions for future use. 3 8 We use LED as a light source for our products. For replacement of LED contact Anour. The product should not be dismantled as it may get damaged. The product should not come into direct contact with water. Our products are marked with the symbol of the crossed out wheelie bin. That means that the product should not be disposed of with other household waste. Our products must be recycled in accordance with local environmental regulations for the disposal of waste. In complying with this you will help to minimize any adverse effect on human and environmental health. If you have any questions please contact Anour. contact@anour.dk (07) EQUIPMENT Ø 4, Ø 5,5 Driver box: ø75 x 30 mm Ø 5,5 () mm. Position & measurement.. Drill 4 holes, place the anchors and fasten the ceiling bracket. 3. Attach the 4 wires to the nipples and tightly fasten the wires to the lamp. The positive pole is the suspension point closest to the touch button. 4. Insert the 4 wires through the holes of the rosette cover 5. Insert the 4 wires in the 4 wire grippers. Follow the colour code to insert the wires in the terminals and the wires in the terminals. 30V DIAGRAM Touch button 500 0 5. Adjust the position of the lamp and then cut the excess of wire. We recommend suspending the light with a distance of / 0cm above a dinning table.. Connect the primary power cable to the terminals on the primary side of the power supply and then, fasten the screw of the safety cap. 7. Close the box / Magnetic closure 8. On / Off / Dimming. Tap on the button on the lamp: less than 3 sec = On/Off. Touch the button: more than 3 sec = brighten or dim. Double tap: for max or min brightness Should be performed according to safety regulations. If the button does not respond, turn off main 8 power for the duration of 9 ø00 = 7,5 kg 30 sec and try again.
G MODEL CORDLESS Installation manual 8 Please, read our instructions before installing and using the product. 7 9 If you have any problems with the electrical installation, contact an electrician. Be sure to turn off the power before you start the installation. In some countries, all electrical installation must be carried out by professional electricians only. For further information, contact the relevant authorities. Our products are for indoor use only. Check on a regular basis that the cord and other parts are not damaged. In this case, the product must not be used. Save these instructions for future use. We use LED as a light source for our products. For replacement of LED contact Anour. The product should not be dismantled as it may get damaged. The product should not come into direct contact with water. Our products are marked with the symbol of the crossed out wheelie bin. That means that the product should not be disposed of with other household waste. Our products must be recycled in accordance with local environmental regulations for the disposal of waste. In complying with this you will help to minimize any adverse effect on human and environmental health. If you have any questions please contact Anour. contact@anour.dk (07) Positive pole 4 0 Negative pole cross the steel wires 5 3 30V. Measure distance between the suspension points. See below.. Drill holes and fasten the plastic ceiling components. 3. Position the driver box (see diagram below), drill holes and fasten it. 4. Attach the wires to the nipples and tightly fasten the wires to the lamp. The positive pole of the lamp is indicated on the lamp with a red point. 5. Insert the steel wires in the plastic ceiling components. Assure that the wires are aligned. cross the steel wires.. Insert the wire in the terminal and the wire in the terminal. You can change the position of the poles by repositioning the wire gripers. 7. Adjust the height of the lamp by pressing the wire griper and then, cut the excess wire, as shown. We recommend suspending the light with a distance of / 0cm above a dinning table. For kitchen table tops, we recommend / 70cm. 8. Connect the primary power cable to the terminals on the primary side of the power supply and then, fasten the screw of the safety cap. Should be performed according to safety regulations. 9. Cut out one input for the primary power cable (3 options shown) in the plastic lid and then attach the white lid to the power supply (magnetic closure). 0. Adjust the angle of the lamp by rotating the body. (Rotation 30 ) DIMENSIONS DRIVER BOX POSITION OPTIONS : DIAGRAM (TOP VIEW) EQUIPMENT Ø 4, Ø 5,5 3 cm 00 cm x 8m x Driver white box: 340x3,5x3 mm (LxWxH) 50 cm Suspension point Ø 5,5 () mm Driver box 0 50 cm Lamp Wire
U MODEL CORDLESS Installation manual cross the steel wires 3 Please, read our instructions before installing and using the product. If you have any problems with the electrical installation, contact an electrician. Be sure to turn off the power before you start the installation. In some countries, all electrical installation must be carried out by professional electricians only. For further information, contact the relevant authorities. Our products are for indoor use only. Check on a regular basis that the cord and other parts are not damaged. In this case, the product must not be used. Save these instructions for future use. Ṉegative pole 7 8 9 We use LED as a light source for our products. For replacement of LED contact Anour. The product should not be dismantled as it may get damaged. The product should not come into direct contact with water. Our products are marked with the symbol of the crossed out wheelie bin. That means that the product should not be disposed of with other household waste. Our products must be recycled in accordance with local environmental regulations for the disposal of waste. In complying with this you will help to minimize any adverse effect on human and environmental health. If you have any questions please contact Anour. contact@anour.dk (07) 5 Positive pole 4 0 Positive pole 30V. Measure distance between the suspension points. See below.. Drill holes and fasten the plastic ceiling components. 3. Position the driver box (see diagram below), drill holes and fasten it. 4. Attach the wires to the nipples and tightly fasten the wires to brackets of the lamp. 5. The positive pole is the suspension point closest to the logo Anour placed on the profile of the lamp.. Insert the steel wires in the plastic ceiling components. Assure that the wires are aligned. cross the steel wires. 7. Insert the wire in the terminal and the wire in the terminal. You can change the position of the poles by repositioning the wire gripers. 8. Adjust the height of the lamp by pressing the wire griper and then, cut the excess wire, as shown. We recommend suspending the light with a distance of / 0cm above a dinning table. For kitchen table tops, we recommend / 70cm. 9. Connect the primary power cable to the terminals on the primary side of the power supply and then, fasten the screw of the safety cap. Should be performed according to safety regulations. 0. Cut out one input for the primary power cable (3 options shown) in the plastic lid and then attach the white lid to the power supply (magnetic closure). DRIVER BOX POSITION OPTIONS : DIAGRAM (TOP VIEW) EQUIPMENT DIMENSIONS Ø 4, Ø 5,5 cm 37,5 cm 50 cm 37,5 cm x 8m x Driver white box: 340x3,5x3 mm (LxWxH) Suspension point Ø 5,5 () mm 50 cm 50 cm Driver box 3 00 cm Lamp Wire