NAME OF WORK - IIM AHMEDABAD - LIBRARY BOQ OF ELV WORKS Description Unit Qty Rate 1 INFORMATION & COMMUNICATIONS TECHNOLOGY (DATA) 1.1 Supply & laying of 25 mm dia. Open/conceal manner medium gauge rigid PVC pipe with GI Rmtr 5,100 pulling wire. Supply & laying of 40 mm dia. Open/conceal manner medium gauge rigid PVC pipe with GI Rmtr 800 pulling wire. Telephone / Data Networking Cabling Supply and laying of specified make Low Smoke Zero Halogen (LSZH) U/UTP CAT6A cable in prelaid PVC conduits or pipes or raceways or cable trays, but without the cost of conduits or pipes or raceways or cable trays. The cable is to be drawn from individual 1.2 workstation area/device/io to the nearest distribution rack or networking rack. It shall be within the scope of integrator/contractor to carry out and submit scanner readings Rmtr 8,400 for all IOs meeting the requirements of relevant EIA/TIA standards as per CAT6A cabling requirements. The integrator/contractor shall submit a detail IO maps, labelling and documentation related to terminations. 1.3 SITC of U/UTP CAT6A RJ-45/RJ-45 Patch Cords Solid Conductor of various lengths a 3ft Nos. 200 b 7ft Nos. 200 1.4 SITC of single U/UTP CAT6A I/O of specified make including mounting inside singlex or duplex or quad faceplate and MS backbox assembly as required as per drawing, inclusive of termination of U/UTP CAT6A cable at each IO at workstation area/device. 200 a b c SITC of singlex faceplate and corresponding MS backbox assembly for installation of 1 U/UTP CAT6A Ios SITC of duplex faceplate and corresponding MS backbox assembly for installation of 2 U/UTP CAT6A IOs SITC of quad faceplate and corresponding MS backbox assembly for installation of 4 U/UTP CAT6A IOs 07 Nos. 38 0
1.8 1.9 Description Unit Qty Rate SITC of U/UTP CAT6A Gigabit patch panel pre-loaded with 24 ports in 1U form factor, with universal A/B labeling and 110 connector terminations on rear of panel allowing for quick and easy installation of 22 to 24 AWG cable, inclusive of termination of u/ftp CAT6A cables at all 24 ports. FIBER OPTIC CABLE & COMPONENTS SITC and Laying of fiber optic cable of 6 cores, Singlemode, Outdoor, Armoured to be laid in prelaid conduits/rcc hume pipes/hdpe/dwc/cable trays/trenches/in underground soil, as applicable, excluding the cost of soft-soil or hard-soil digging. 5 Rmtr 200 1.10 SITC of wall mounted modular shelf / LIU for optical splicing/termination of 12 core singlemode fiber optic cable as per design specifications. It shall be complete with adaptor panels, adaptors and splice trays for using LC type termination. Masking/blanking/dustcover for unused/unmounted adaptor ports, inclusive of all mechanical accessories. 1.11 SITC of 19" rack mounted modular shelf / LIU for optical splicing/termination of 12 core singlemode fiber optic cable as per design specifications. It shall be complete with adaptor panels, adaptors and splice trays for using LC type termination. Nos. 3 Masking/blanking/dustcover for unused/unmounted adaptor ports, inclusive of all mechanical accessories. 1.12 SITC of LC-LC duplex fiber optic patch cords of 2 mtr/6 ft., singlemode Nos. 6 1.13 SITC of LC type pre-terminated fiber optic cable pigtails of 2 mtr/6 ft., singlemode 2 1.14 Splicing / Termination of Fiber Optic Fiber Cable Cores using Fusion splicing with preterminated LC pigtails, dressing and proper fixing in splice trays. 2 1.15 1.16 Supply, Installation, Testing and Commissioning of External splicing kits or joints for optical splicing of outdoor fiber optic cable, IP 66 rated. NETWORKING ENCLOSURES SITC of 19" wide mounting frame Networking Enclosures of various sizes and capacities complete with all accessories, including all provisions to ensure that it is rodent-proof, i.e., use of suitable glands etc. at all cable entry and exit points. a 15U, 600mmW x 600mmD, wall mounted, 2 x 90cfm fans b 22U, 800mmW x 800mmD, floor mounted, 4 x 90cfm fans c 42U, 1000mmW x 1000mmD, floor mounted, 4 x 90cfm fans Total 1
Description Unit Qty Rate 2 VIDEO SURVEILLANCE / CCTV SYSTEM 2.1 Supply & laying of 25 mm dia. open/conceal manner heavy guage rigid PVC pipes. Rmtr 1,100 2.2 2.3 Supply and laying of specified make Low Smoke Zero Halogen (LSZH) U/UTP CAT6A cable in prelaid PVC conduits / pipes / raceway, but without the cost of raceway or pipe. Rmtr 1,800 SITC of U/UTP CAT6A RJ-45/RJ-45 Patch Cords Solid Conductor of various lengths a 3ft Nos. 48 b 7ft Nos. 48 2.5 Supply and Installation of U/UTP CAT6A RJ-45 I/O of specified make including single faceplate and MS backbox assembly, inclusive of termination of CAT6A cable at each IO at workstation area / device / desktop / or at a patch panel inside a rack. Nos. 48 2.6 2.7 2.8 SITC of Full High Definition Network Cameras, indoor CS-Mount type, 1/3 CMOS/MOS/CCD sensor, 5-50mm varifocal lens, minimum resolution 2MP (1920x1080), 1080p resolution at frame rates 30fps or better, H.264 High profile, JPEG support, Day/Night operation, ONVIF Profile S compliant, complete with IK10 rated vandal resistant housing and Power on Ethernet (PoE) based on 802.3a/f. SITC of Network Video Recorder(s) with a capacity to store the content for upto 32 cameras for 24Hrs x30days at 25fps and 1080p including hard disks for required duration and frame rates and capable of recording of at least additional 50% cameras for future expansion. Vendor shall submit bandwidth and storage calculator for the proposed camera models. It shall be inclusive of Video Management Software and licences for the specified number of cameras. SITC of Client PC with Intel Core i7 870 or higher processor with 8 GB of RAM DDR3, 1 TB SATA II hard drive for OS and VMS applications, 1 GB PCI-Express x 2 dual-head video adapter, 1600 x 1200 or higher screen resolution, 100/1000 Ethernet Network Interface Card and 16x DVD+/- RW Drive along with appropriate Operating System, with minimum 21'' LED display. Nos. 48 Nos. 2
2.9 Description Unit Qty Rate SITC of 55" Full HD LED Professional Display for Monitoring with at least 2 x HDMI/DVi ports, 1 x USB and 1 x LAN, bezel dimensions not exceeding 5-8mm and inclusive of mounting accessories. Nos. 2 Total 2 3 FIRE ALARM SYSTEM 3.1 Supply & laying of 25 mm dia. open/conceal manner heavy gauge/hms PVC conduits. Rmtr 800 3.2 Supply & Laying of FRLS type 2x1.5 Sq mm flexible cable for fire alarm system. Rmtr 1,000 3.3 SITC of Microprocessor based networkable addressable type fire alarm control panel with display. The panel should be equipped with 1 installed loop with each loop having a capacity of connecting a minimum of 150 addressable detectors and 150 addressable modules or a mix of up to 250 detectors and devices in any combination, operating at 240 volts AC power supply, and equipped with automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working. The panel shall be supplied with all accessories, control modules and power supplies in the required quantities as per site requirements for all types of field devices to make the system fully operational. The panel shall be UL 9th Edition Listed and FM Approved. Interconnecting of multiple panels shall be possible via hardware interfaces and software. A copper supporting interface shall be supplied by default. Irrespective of whether or not mentioned in the BoQ, all necessary interfaces - such as hardware including any fiber optics modules, if required and/or software - for 3.4 3.5 Supply, Installation, Testing and Commissioning of interface for interconnecting multiple fire alarm system panels over fiber optics media based communication, transceivers or optics must support 100Mbps. Supply, Installtion, Testing and Commissioning of Repeater Panel with 6 inch or 640- characters display. The LCD shall display all events / detectors, devices status of complete systems in the networkas per technical specification etc. as required.
3.6 3.7 Description Unit Qty Rate Supply, Installtion, Testing and Commissioning of Addressable photo+thermal Multi- Sensing Type Detector (heat+smoke) with mounting base, LED, Address Switch, inclusive of detector base and complete with all accessories as required. The detector shall be UL listed. The detector shall include mounting arrangements for direct installation on ceiling/slab. Supply, Installtion, Testing and Commissioning of Addressable Photoelectric/Smoke Detector with mounting base, LED, Address Switch, inclusive of detector base and complete with all accessories as required. The detector shall be UL listed. The detector shall include mounting arrangements for direct installation on ceiling/slab. 2 Nos. 90 3.8 Supply, Installtion, Testing and Commissioning of Addressable Rate of Rise Cum Fixed Temperature detector with mounting base, LED, Address Switch to program the detectors and complete with all accessories as required. The detector shall be UL listed. The detector shall include mounting arrangements for direct installation on ceiling/slab. 3.9 Supply, Installation, Testing and Commissioning of Addressable Beam Detector (Tx-Rx pair) Nos. 6 including mounting base along with Interface module to connnect to the loop. 3.1 Supply, Installtion, Testing and Commissioning of Addressable Manual Pull Station with Key 5 Reset. 3.11 Supply, Installation, Testing and Commissioning of Addressable Relay module. Nos. 5 3.12 Supply, Installation, Testing and Commissioning of Addressable Monitor module. Nos. 5 3.13 3.14 3.15 3.16 Supply, Installtion, Testing and Commissioning of Addressable type isolator modules for isolating shorted, dewired and loose circuits between two successive fault isolators with automatic resetting arrangement. Supply, Installtion, Testing and Commissioning of Sounder and Strobe as per NFPA72 edition; inclusive of control modules. The strobes shall be capable of being synchronized for better evacuation. SITC of Response Indicator with matching screws complete with GI Junction box, cable lugs at cable end and ferruling and any other hardware as appropriate. Supply, Installtion, Testing and Commissioning of Addressable Duct detector complete with all accessories for mounting inside HVAC ducts as required. Nos. 6 5 2 Nos. 3
Description Unit Qty Rate Supply, Installation, Testing & Commissioning of Fire Command Workstation including Graphical User Interface based software. This shall include any cards, modules, hardware interfaces based on TCP/IP Ethernet communications protocol over fiber optics based media and softwares for providing connectivity and communication between multiple fire alarm system panels. 3.17 The GUI based main network software shall be capable of graphically representing each node being monitored with floor plans and icons depicting the actual locations of the various systems; and / or sensors locations. The GUI software shall be located in control room and shall monitor all the blocks panel connected with each other. Graphic software will interface with fire network via network interface card and shall be able to control and monitor voice evaquation and two way communication system. It shall be inclusive of necessary server grade hardware and min. 42" professional LED Total 3 4 ACCESS CONTROL SYSTEM 4.1 Supply & laying of 25 mm dia. open/conceal manner heavy guage rigid PVC pipes. Rmtr 50 4.2 Supply and laying of specified make Low Smoke Zero Halogen (LSZH) U/UTP CAT6A cable in prelaid PVC conduits / pipes / raceway, but without the cost of raceway or pipe. Rmtr 50 4.3 CAT6A U/UTP RJ-45/RJ-45 Patch Cords Solid Conductor 3ft Nos. 2 CAT6A U/UTP RJ-45/RJ-45 Patch Cords Solid Conductor 7ft Nos. 2 4.5 Supply and Installation of U/UTP CAT6A RJ-45 I/O of specified make including single faceplate and MS backbox assembly, inclusive of termination of CAT6A cable at each IO at workstation area / device / desktop / or at a patch panel inside a rack. Nos. 2 4.6 SITC and laying of 6Core X0.5Sqmm Multistrand Copper Cable Nos. 20 SITC and laying of 4Core X0.5Sqmm Multistrand Copper Cable Nos. 20
Description Unit Qty Rate SITC of ACS smart card based door controller having 1 Door Controller and in-built 4.7 reader Nos. 2 with power over ethernet and 12V DC. 4.8 SITC of smart card based exit reader. Nos. 2 4.9 SITC of GUI based Application Software for Access Control Configuration & Management. 4.1 SITC of Emergency Break Glass Unit Nos. 2 4.11 SITC of Emergency Electro Magnetic locks 600 lbs with All Necessary Accessories Nos. 2 4.12 SITC of Contactless smart Card based on technology MIFAREÂ, DESFire EV1, MIFAREÂ Classic. 0 Total 4 5 PUBLIC ADDRESS SYSTEM 5.1 Supply & laying of 25 mm dia. open/conceal manner heavy guage rigid PVC pipes. Rmtr 600 5.2 5.3 SITC of 2-Core 1.5 sq.mm (15AWG) flexible cable for connecting loudspeakers from power amplifiers. Main Unit / Network Controller for Public Address System consisting of Central Digital Signal Processor module, 2 x 16-character LCD Display, 8 Supervised Control Inputs and 4 Audio Inputs, Ethernet Interface for Configuration and Diagnostics & Logging functions, Digital message storage capable of storing at least up to last 200 faults messages, RS232 Interface for logging, OFC Network Inteface capability, PC Interface and inclusive of connectivity provisions with Fire Alarm System. It will support essential capabilities such as - pre-programmed emergency messages, background music & configurable multiple zones and be compliant with EN60849 or equivalent internationally accepted EVAC standards. PA system controller shall support important availability features such as loudspeaker line (zone) monitoring and loudspeaker monitoring without requiring any additional cabling for Rmtr 750
5.4 Description Unit Qty Rate Class D Power Amplifier - minimum 200 watts for the amplification of audio signals for speakers. The amplifier shall support minimum 2 zones each of minimum 200 watts. It shall be possible to select output voltages of 100 V, 70 V or 50 V, The power amplifier will have a 2 x 16-character display for status display and must be usable free-standing (tabletop) or in a 19" rack mounting arrangement. 5.5 5.6 5.7 5.8 Class D Power Amplifier - minimum 400 watts for the amplification of audio signals for speakers. The amplifier shall support 1 zone. It shall be possible to select output voltages of 100 V, 70 V or 50 V, The power amplifier will have a 2 x 16-character display for status display and must be usable free-standing (tabletop) or in a 19" rack mounting arrangement. Main/primary digital paging microphone capable of supporting upto 6 zones, inclusive of provision to announce over background music and a press-to-talk key, It should have an Analog-to-digital audio conversion circuit within the call station and a digital signal processor, which can be used for audio processing. Supply, Installtion, Testing and Commissioning of Digital Remote Paging/PA Microphone with High Quality Condenser Gooseneck Style Microphone, with facility of 6 Keypad buttons for zone selection, relay of pre recorded messages/alarm messages/tones/call routines, up gradable to any number of zone selection, by adding keypad etc. connectivity Fibre/ CAT-5 cable. For installation at a remote location with necessary interfaces and cables. Ceiling Loud Speaker: Max. Power 9 W,Rated Power 6 Watts, Rated Voltage: 100 volts,effective frequency range :(80 Hz to 16000 Hz). Speakers should be capable of being monitored. Nos. 40 5.9 Wall Mounted Speaker: Max. Power 25 W,Rated Power 15 Watts, Rated Voltage: 100 volts, Effective frequency range :(80 Hz to 16000 Hz). Speakers should be capable of Nos. 7 being monitored. 5.10 Speaker Volume Controller for 100v line signals. It enable the user to conveniently adjest volume for of a Speaker or group of Speakers. It is available in different Power rating like 12 W, 36 W and 100 W versions, Built-in 24 V DC override relay. These volume controls and program selectors comply with the relevant safety and installation regulations of EN 60065. 5.11 SITC of set of cables for putting the complete PA system into operation. Set 1
Description Unit Qty Rate 5.12 External background music source & accessories- DVD/Tuner/MP3 5.13 Web based Software Application for System Configuration, Management & Diagnostics 5.14 NETWORKING ENCLOSURES SITC of 19" wide mounting frame Networking Enclosures of various sizes and capacities complete with all accessories, including all provisions to ensure that it is rodent-proof, i.e., use of suitable glands etc. at all cable entry and exit points. 22U, 800mmW x 800mmD, floor mounted, 4 x 90cfm fans Total 5