Boiler Steam Iron Philips Consumer ifestyle Service Manual PRODUCT IFORMATIO Features Iron - Careeza soleplate - Steam rate (Max): 110 g/min - Steam trigger with lock - Steam hose length: 1.8 m TECHICA IFORMATIO Voltage : 220-240 V Frequency : 50-60 Hz Power Iron : 800 W Boiler : 1370 W Dimension (F-box) : 350 x 350 x 250 mm ( x W x H) Weight (with packing) : 6.4 kg Stand - Inox boiler - Boiler pressure: 4.5 bar - Fixed water tank volume: 1.0 - Cord length: 2.0 m - Flex & hose-cord storage hook - Easy rinse Safety Information - This product meets the requirements regarding interference suppression on radio and TV. - After the product has been repaired, it should function properly and has to meet the safety requirements as officially laid down as this moment. Water advice If the tap water in your area is very hard, it is advisable to mix the tap water with an equal amount of demineralised water. Easy to rinse The new design of the rinse cap makes it very easy to rinse the boiler regularly. Simply unscrew the cap and pour out the dirty water into the sink. o hassle with coins, extra tubes or anything of this sort. Fixed water tank The fixed water tank that is incorporated into the stand allows re-filling anytime during ironing. Since water is not re-filled directly into the boiler, there is no waiting time for boiler to cool down. Published by Philips Consumer ifestyle Printed in the etherlands Copyright reserved Subject to modification 08/08
DISASSEMBY ADVICE - IRO BACKPATE 1 SWIVE 2 HOSE CORD ASSY 3 Remove Screw A Disassemble BACKPATE 1 Remove Screw B1, B2 Remove Clamping plate Remove Quick-connect S, E,, Disassemble SWIVE 2 Remove HOSE CIP 10 Disassemble Steam hose Disassemble HOSE CORD ASSY 3 Steam hose S Black HOSE CIP 10 Green E B2 B1 Brown Power cord Fig 1. Wiring at rear HOUSIG (Part 1) Clamping plate IAY 4 AMP ASSY 7 MICROSWITCH ASSY 9 TRIGGER 12 THERMOSTAT DIA ASSY 14 HOUSIG PRITED 16 SOEPATE COVER 17 THERMOSTAT BUSH 19 RUBBER HOSE 20 BRASS JOIT 21 SOEPATE ASSY 23 Remove Screw A Disassemble BACKPATE 1 Disassemble TRIGGER 12 Tip: Disassemble TRIGGER by inserting a sharp object into the gap at the rear of the trigger & prying upward. Remove Screw C Release Inlay rear catch Disassemble IAY 4 Disassemble AMP ASSY 7 Disassemble MICROSWITCH ASSY 9 Disassemble THERMOSTAT ASSY 14 S Black (Microswitch) (Micro switch) (amp assy) Fig 2. Wiring at rear HOUSIG (Part 2) White (amp assy) Fig 3. Remove Screws D1, D2, D3 Disassemble HOUSIG PRITED 16 Remove Screws E1, E2, E3 Remove HOSE CIP 22 Disassemble SOEPATE COVER 17 2-7
PARTS IST - IRO & EECTRICA DIAGRAM Pos Service code Description 1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19 20 21 22 23 4239 026 30740 4239 026 30750 4239 021 41080 4239 021 47570 4239 026 08280 4239 026 30790 4239 021 46060 4239 026 01220 4239 021 42390 4239 010 10110 4239 026 30780 4239 014 54370 4239 021 47590 4239 026 30770 4239 021 47580 4239 026 30760 4239 015 70150 4239 026 13220 4239 015 56530 4239 010 09350 4239 010 10280 4239 021 41290 Backplate Swivel Hose cord assy Inlay on SOS assy amp cover Steam lock amp assy amp holder Microswitch assy Hose clip - Iron Trigger Trigger spring Thermostat dial assy Rattle spring Housing printed Soleplate cover Ryton ring Thermostat bush Braided rubber hose - non SOS Brass joint Hose clip - braided rubber hose Soleplate assy 230 V Thermistor 1 Trigger Switch Boiler Electronics S Pump M Thermal Fuse Boiler Heating Element Electrovalve Thermostat Thermal Fuse Heating Element STAD IRO Fig 4. Electrical diagram 3-7
EXPODED VIEW - IRO 2 3 5 6 12 A 13 C 1 7 8 9 4 D2 D3 10 B1 B2 15 Cord clamp D1 21 14 16 E2 22 20 E1 E3 17 19 22 18 23 4-7
DISASSEMBY ADVICE - STAD TRAY RUBBER CAP 30 TRAY ASSY 33 DOOR ASSY 35 Remove TRAY RUBBER CAP 30 (3x) Remove Screw F1, F2, F3 Disassemble TRAY ASSY 33 Remove Screw G Disassemble DOOR ASSY 35 FROT PAE PRITED 37 POWER BOARD 43 IGHT SWITCH 44 Remove TRAY RUBBER CAP 30 (3x) Remove Screw F1, F2, F3 Disassemble TRAY ASSY 33 Remove Screw H1, H2 Disassemble FROT PAE 37 Disassemble IGHT SWITCH 44 Disassemble POWER BOARD 43 PARTS IST - STAD Pos Service code Description 30 33 34 35 36 37 38 39 40 41 42 44 45 4239 015 57990 4239 021 47640 4239 021 47600 4239 021 47680 4239 026 30800 4239 021 47620 4239 021 39540 4239 017 10420 4239 017 09890 4239 015 56880 4239 010 10260 4239 017 11110 4239 022 61560 Tray rubber cap Tray assy Water tank assy Door assy Hose cord cap Front panel printed Boiler assy High End Thermistor Electrovalve Braided rubber hose - boiler Inox clamp - boiler ight switch Control board-pump assy High End WATER TAK ASSY 34 HOSE CORD CAP 36 BOIER ASSY 38 BRAIDED RUBBER HOSE - BOIER 41 PUMP ASSY 45 IET TUBE - PUMP 46 DE-AIR TUBE 47 RISE RUBBER COUPIG 50 RISE BUSH 51 RISE CAP ASSY 52 Remove TRAY RUBBER CAP 30 (3x) Remove Screw F1, F2, F3 Disassemble TRAY ASSY 33 Remove Screw H1, H2 Disassemble FROT PAE 37 Disassemble HOSE CORD CAP 36 Disassemble RISE CAP ASSY 52 Disassemble RISE BUSH 51 Disassemble RISE RUBBER COUPIG 50 Remove Screws K1, K2, K3, K4 Disconnect IET TUBE - PUMP 46 Disconnect DE-AIR TUBE 47 Disassemble WATER TAK ASSY 34 Disassemble BRAIDED RUBBER HOSE - BOIER 41 Disassemble PUMP ASSY 45 Remove Torx screws 1, 2, 3 Disassemble TOP SPACER 48 Disassemble BOIER ASSY 38 Pos Service code Description 46 47 48 49 50 51 52 55 56 57 58 65 4239 015 56860 4239 015 56870 4239 026 26120 4239 026 26110 4239 015 56760 4239 026 30820 4239 021 47630 4239 000 10100 4239 021 47610 4239 015 52340 4239 026 05990 4239 026 26480 Inlet tube - pump De-air tube Top spacer Bottom spacer Rinse rubber coupling Rinse bush Rinse cap assy Cordset EU Stand bottom assy Bung Filling cup De-air valve High End ote: For Pos 45, please replace both components together when either one is faulty. The 2 components come as a service kit. 5-7
EXPODED VIEW - STAD F3 30 33 58 F1 F2 G 35 K1 H1 K2 H2 41 34 36 37 52 51 50 47 40 46 45 65 1 2 3 42 38 48 49 44 39 55 56 Cord clamp Clamping plate K3 K4 57 6-7
= = REPAIR ISTRUCTIOS - Due to the high wattage of the iron, only the specified cord set must be used. - Should damage be observed on the HOSE-CORD ASSY 3 or CORDSET 55, they must be replaced. Continued usage is not allowed. - When replacing the MICROSWITCH ASSY 9, please dress the 2 attached wires such that they are free of tension. Pulling force on the wires may affect the steam triggering. - To avoid damage to the sealing & components of the BOIER ASSY 38, EVER clean the boiler assy with vinegar, descaling agent or other corrosive chemicals. - When replacing EECTROVAVE 40 or PUMP ASSY 45, please be reminded to apply loctite at the joints for good sealing. - After the product has been repaired, it should function properly and has to meet the safety requirements & legal regulations as laid down & officially established at this moment. - The following tests are common checks that are conducted on a repaired product before it is returned to the consumer. 1. Soleplate temperature Check that soleplate temperature is within IEC requirement. Measure the temperature of the soleplate after the iron has reached steady state i.e connected to the mains for at least 15 minutes. The table below shows the temperature requirement. Soleplate temperature (Deg C) Marking Minimum Maximum ominal + Tolerance Material, for example (1 dot) 70 120 95 ± 25 Acetate, elastane, polyamide, polyproylene (2 dots) 100 160 130 ± 30 Cupro, polyester, silk, triacetate, viscose, wool (3 dots) 140 210 175 ± 35 Cotton, linen Testpoint 2. eakage current Check that leakage current is within IEC requirement. Measure leakage current between IVE/EUTRA & EARTH. IEC requirement is that at 230 V supply, the EARTH leakage current must be less than 0.75 ma. 3. Water leakage / Functionality Check that there is no water leakage from any part of the product during operation. Check that the functionality of the product (product dependent) eg. steaming, variable steam, SOS, ASO etc is working properly. 4. oose part Check that there are no loose parts eg. extra screw in the product that can cause short-circuit or product malfunction. 7-7