Owner's Manual (00 Gallon Lawn Service Skid Sprayer) Technical Specifications. Horsepower Recoil Start Engine Roller Cast Iron Pump 0 Gallons Per Minute at 0 PSI Pressure Gauge-Adjustable Pressure Range Suction Line Filter Handgun-0' Handgun /" Hose Dual Jet Agitation Operation Add gas and oil to the engine as specified in the engine manual. Check the side port of the engine gear case for lubricant. Add more lubricant if necessary. See the engine manual for type of lubricant needed. It is important to test the sprayer with plain water before attempting actual spraying. This will enable you to check the completed sprayer for leaks in the plumbing system.. Open tank lid and be sure the tank is clean and free of foreign material. Fill the tank about one half full with plain water.. Open the valve in the strainer assembly and allow water to flow to the pump. (The valve is located at this point to enable the strainer to be taken apart for cleaning.) CAUTION: Always be sure that water has reached the roller pump before starting your sprayer. If the pump is run dry, serious damage to the pump will result. General Information Thank you for purchasing this product. The purpose of this manual is to assist you in operating and maintaining your skid sprayer. Please read it carefully, as it furnishes information which will help you achieve years of trouble-free operation. Warranty/s/Service Products are warranted for one year from date of purchase against manufacturer or workmanship defects. Commercial users have a 0 day warranty. Your authorized dealer is the best source of replacement parts and service. To obtain prompt, efficient service, always remember to give the following information.... It is always best to start the sprayer at little or no pressure. This sprayer is equipped with a spring loaded relief valve. Turn the valve handle out to decrease pressure and in for increased pressure. The location of the relief valve and other important components may be found by referring to the exploded view drawings.. The pumping system includes an agitator which will help keep the solution in suspension. Pressure to the agitator should never exceed 00 PSI. When spraying at pressures over 00 PSI, use the brass valve (in the hose reel/agitator plumbing assembly) to throttle the pressure to the agitator by closing the valve. As solution is forced through the agitator, the venturi action triples the flow through the agitator. The valve in the line may shut off the agitation completely when not needed, or it can throttle the amount of solution going to the agitator if too much agitation occurs.. You may now start the sprayer engine following the engine manufacturers instructions. Let the sprayer run at low pressure until water has reached the handgun, and all air has been purged from the handgun line.. The pressure should now be increased to -0 PSI. Operate the sprayer at this increased pressure for - minutes, thoroughly testing the unit before adding chemicals.. The sprayer should now be ready for adding chemicals. - Correct Description and/or part number. - Model number/serial number of your sprayer. descriptions and part numbers can be obtained from the illustrated parts list section(s) of this manual. Whenever you need parts or repair service, contact your distributor/dealer first. For warranty work, always take your original sales slip, or other evidence of purchase date, to your distributor/dealer. www.fimcoindustries.com 000 FIMCO Lane, P.O. Box 00, North Sioux City, SD 0 Toll Free Phone: 00--00 : Toll Free Fax: 00--00 Form No. [00 (0/0)] Printed in the U.S.A.
Delta Jet Agitator (00) w/color-coded Inserts Blue /" Orifice White /" Orifice Strap/Buckle Detail Strap Attachment to a "Bent" Buckle Black /" Orifice Red /" Orifice Venturi action more than triples the effective flow of liquid, for thorough agitation. Orifice Color Black Red Blue White Performance Chart Orifice P.S.I. Inlet Flow (G.P.M.) /". /" /" /"... Outlet Flow (G.P.M.).... Approx. " Operation As solution is forced through the agitator, the venturi action triples the flow through the agitator. The valve in the line may shut off the agitation completely when not needed, or it can throttle the amount of solution going to the agitator if too much agitation occurs. The nylon straps are to be inserted in and out of the slots in the buckle, as shown. Be sure the straps are snug before tightening the hook bolts. In most cases, it will be necessary to re-tighten the straps after filling the tank with liquid. PISTON TYPE PRESSURE RELIEF/REGULATING VALVES Bypasses excess liquid. Adjustable to maintain control of line pressure at any pressure within the valve operating range. Selected pressure setting firmly held in place by locknut. Extra large passages to handle large flows. & () 0 Model 0 - Polypropylene with stainless steel spring - Excellent chemical resistance - EPDM O-Rings - For pressure to 0 p.s.i. - /" port for pressure gauge - Choice of /" or /" NPT (M) inlet & (F) outlet connections FIMCO 00 Mfg Description 0-/-PP 0-/-PP /" Poly Valve /" Poly Valve.00.00 PK-AB0-KIT Repair Kit, s Marked **. No. 0 Mfg 00 Description ** CP-SS Retaining Pin ** CP-SS Spring ** CP--EPR O-Ring, EPDM Rubber Pipe Plug, /" MNPT CP-PP - Poly Body (/" NPT) CP-PP - Poly Body (/" NPT) 00 CP-NY Adjusting Cap, Nylon (Gray) 0. 00 CP-PP Spring Retainer. 0 CP-PP Lock Ring. 0 CP-PP Guide Seat. How to order: Specify valve number (Example: 0-/-PP Polypropylene) Page
#0 (-Roller Pump) Exploded View/s 0 0 No * 00 * 00 * 0 Description O-Ring Gasket Viton Seal (Standard) Super Roller (Standard)..00. 00-00 0-00 Shaft Key (Stainless Steel) 00 Body (Cast Iron w/seal) 0.00 Pump Speed (RPM) 00.0 0 p.s.i. Performance data for pump No. 0 0 p.s.i.... 00 p.s.i.... 0 p.s.i.. 00 p.s.i. 0.. 0 p.s.i. 0.0 0 p.s.i.... 0 0 0 0 00 00 00 End Plate (Cast Iron). Bearing Cover.0 Shaft Bearing Cover.0 Sealed Ball Bearing H.H.C.S., /"- x /" Key... Rotor (Phenolic).00 * = s Available ONLY in Repair Kit # ($.) No. Description ** Gasket, Nylon ** Seat Plug, Seat Plate, Washer, & Core Sub-Assembly ** Packing Washer, Type Stainless Steel ** Packing, Leather 000 Inlet Body, Aluminum.0 000 Handle Body, Aluminum. 000 Stop Adjustment Nut, Steel - Zinc Plated. 00 Locknut, Steel - Zinc-Plated. 00 Stem Nut, Steel - Nickel Plated. 0 0000 Tubing, Aluminum. 00 Washer, Stainless Steel. 00 Spring Guide Washer, Type Stainless Steel. 00 00 00 00 0 0 00 0 00 00 0 00 0 0 00 0 0 Spring for Stop Adjustment Nut, Stainless Steel Trigger Stop Spring, Stainless Steel Main Spring, Stainless Steel Cap, Aluminum Orifice Disc, Stainless Steel Gasket, Nylon Trigger Guard, Steel - Nickel Plated Guide Vane, Nylon Nozzle Housing, Aluminum Rivet, Steel - Zinc Plated Spring Screw, Steel - Zinc Plated Screw, Stainless Steel Packing Screw, Aluminum Trigger Stop, Steel - Nickel Plated Stem, Type Stainless Steel Spring Stud, Stainless Steel Trigger Guide, Steel - Nickel Plated Trigger, Steel - Nickel Plated..... 0...0......0.0.. 0 0 Exploded View/s : Handgun #0 ** = Available in Spare s Kit ONLY! 0 (#PK-AB-AL-KIT) ($.) Page
Exploded View LSS-0 (0) F 0 D......... DETAIL D (xs). 0. DETAIL F........0....................... Page
No s : LSS-0 (0) Description 00 /"-0 Hex Whiz (Flange) Locknut. 00 /"- Hex Whiz (Flange) Locknut. 00 /"- Hex Whiz (Flange) Locknut. 000 Nylon Elbow, /" MNPT x /" HB. 00 Nylon Elbow, /" MNPT x /" HB. 0 /" x /" Galv. Pipe Nipple.0 00 Delta Jet Agitator. 00 Garden Hose Washer.0 00 Hose, /"- Brd. x 0". 0 00 Hose, /"- Brd. x ". 00 Hose, /"- Brd. x ". 00 Hose, /"- Brd. x 0 Ft.. 00 Hose, /"- Brd. x 0". 00 Hose, /"- Brd. x 0". 00 Hose, /"- Brd. x ".0 00 H.H.C.S., /"- x /" (Full Thread). 0 /" x " Hook Bolt. 0 Round U-Bolt, /"-0 x " x /" (/" Thread).0 0 Handgun Holder Bracket. 0 00 /" N.P.T. Galv. Hex Pipe Cap. 00 Hose Clamp, /". 0 Hose Clamp (/"-/"). 00 Nylon Elbow, /" U.N.F. x /" HB. 00 Steel Fitting, /" MNPT x /" HB. 00 Rubber Grommet (Black). 00 Tank Strap Buckle, Bent. 0 /"- x " Flange Whiz Lock Screw. 0 Nylon Strap ( /" x ").00 0 GunJet Spray Gun. 0 Gauge, Liquid-Filled, 0-00# p.s.i.. 00 00 Gallon Horizontal Tank.00 Manual Hose Reel.00 Hose Reel Mount.00 Engine/Pump Sub-Assembly 00.00. 0 Reverse Rotation -Roller Pump.. 0. H.P. Engine w/ Gear Reduction.. 00 Adapter & Kit (Coupler).. 00 /" Square Keystock x /" Long.0. 000 /" Square Keystock x /" Long.. 0 Torque Bracket.. 0 /"- x /" Flange Lock Screw.. 0000 Rubber-Headed Machine Screw Bumper (#0-).. 00 #0- Hex Whiz (Flange) Locknut..0 0000 Nylon Fitting, /" MNPT x /" HB.. 00 Shield.. 00 Lockwasher, /". Strainer Assembly.0. 0 Strainer Bracket.. 00 /"- Hex Whiz (Flange) Locknut.. Strainer... 0 Strainer Cap... 00 Strainer Bowl (Nylon).0.. 0 Viton Gasket.0.. Screen (0 Mesh).. 00 Round U-Bolt, /"- x /" x /".. 0000 Nylon Fitting, /" MNPT x /" HB.. 00 Nylon Close Nipple, /" MNPT.. 0 /" (T-00) Brass Ball Valve. Hose Reel/Agitator Plumbing Assembly (LSS-0).. 00 /" Galvanized Close Nipple.. 000 /" NPT Galvanized Tee.. /" T-00 Brass Ball Valve.. 00 Nylon Fitting, /" MNPT x /" HB.. 00 Nylon "Tee" Fitting, /" FNPT.0. 00 Nylon Reducing Bushing, /" MNPT x /" FNPT.. 00 Steel Fitting, /" MNPT x /" HB. Pressure Relief Valve Assembly.. 00 Nylon Close Nipple, /" MNPT.. 00 Nylon Gauge Tee, /" FNPT.. Pressure Relief Valve, (/" NPT).00. 00 Nylon Fitting, /" MNPT x /" HB.. 00 Nylon Fitting, /" MNPT x /" HB. 0 Skid (00 Gallon (RED). After Spraying After use, fill the sprayer tank part way with water. Start the sprayer, and allow the clear water to be pumped through the plumbing system and out through the spray nozzles. Refill the tank about half full with plain water and use FIMCO Tank Neutralizer and Cleaner, and repeat cleaning instructions above. Flush the entire sprayer with the neutralizing/cleaning agent, then flush out one more time with plain water. Follow the chemical manufacturer's disposal instructions of all wash or rinsing water. For the boom, (if applicable) remove the tips and screens from the nozzle assemblies. Wash these items out thoroughly. Blow the orifice clean and dry. If the orifice remains clogged, clean it with a fine bristle (NOT WIRE) brush, or with a toothpick. Do not damage the orifice. Water rinse and dry the tips before storing. WARNING: Some chemicals will damage the pump valves if allowed to soak untreated for a length of time! ALWAYS flush the pump as instructed after each use. Winter Storage Drain all water out of your sprayer, paying special attention to the pump, handgun, and valve(s). These items are especially prone to damage from chemicals and freezing weather. The sprayer should be winterized before storage by pumping a solution of RV antifreeze through the entire plumbing system. This antifreeze solution should remain in the plumbing system during the winter months. When spring time comes and you are preparing your sprayer for the spray season, rinse the entire plumbing system out, clearing the lines of the antifreeze solution. Proper care and maintenance will prolong the life of your sprayer. ( s are Subject to Change) Page