Originl operting instructions SLS 96 Protective throughem photoelectric sensors Dimensioned drwing en 09-2010/11 602075 65m 39m 10-30 V DC 500 Hz Protective throughem photoelectric sensor with high performnce reserve in visile red light or infrred light, up to ctegory 2 in ccordnce with ISO 13849-1 Roust metl housing with glss cover or plstic housing, protection clss IP 67 for industril ppliction 2 indictors ech t the trnsmitter nd receiver for displying their sttus when commissioning nd in opertion Optics heting for use with low tempertures Connection vi M12 connector or terminl comprtment A B C D E F G H I Green indictor diode Yellow indictor diode Trnsmitter/receiver Opticl xis Device plug M12x1 Screwed cle glnd M16x1.5 for Ø 5 10mm Countersinking for SK nut M5, 4.2 deep Connection terminls Cle entry Electricl connection We reserve the right to mke chnges DS_SLS_96_en.fm IEC 60947... IEC 60947... Accessories: (ville seprtely) IP 67 U L US C LISTED Mounting systems (BT 96, BT 96.1, UMS 96, BT 450.1-96) M12 connectors (KD ) Redy-mde cles (K-D ) Test monitoring units TNT 35 (Prt No. 50033058) BT 96-ARH lignment id (Prt No. 50080502) Sensorscope SAT 5 (lignment control, Prt No. 50109545) Terminls Connector, 4-pin Trnsmitter Leuze electronic GmH + Co. KG In der Brike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 info@leuze.de www.leuze.com SLS 96 M/P - 08
Specifictions Infrred light Red light Sfety-relevnt dt Type in ccordnce with IEC/EN 61496 type 2 Performnce Level (PL) in ccordnce with PL d ISO 13849-1 1) Ctegory in ccordnce with ISO 13849 1) ct. 2 Men time to dngerous filure (MTTFd) 400 yers Service life (TM) 20 yers Opticl dt Typ. operting rnge limit 2) 0 65m 0 39m Operting rnge 3) 0 50m 0 30m Light source LED (modulted light) LED (modulted light) Wvelength 880nm 660nm Timing Sensor switching frequency 500Hz Sensor response time 1ms Dely efore strt-up 200ms Electricl dt Operting voltge U 4) B 10 30VDC (incl. residul ripple) Residul ripple 15% of U B Open-circuit current 50mA Switching output PNP trnsistor Function light switching Signl voltge high/low (U B -2V)/ 2V Output current mx. 100mA Indictors Green LED redy Yellow LED light pth free Yellow LED, flshing light pth free, no performnce reserve Trnsmitter Green LED redy Yellow LED trnsmitter ctive Mechnicl dt Plstic housing Metl housing Housing polycronte diecst zinc Optics cover plstic glss Weight 150g 380g Connection type terminls or M12 connector Environmentl dt Amient temp. (opertion/storge) -20 C +60 C/-40 C +70 C Protective circuit 5) 1, 2, 3 VDE sfety clss 6) II, ll-insulted Protection clss IP 67 LED clss 1 (cc. to EN 60825-1) Stndrds pplied IEC 60947-5-2 Options Optics heting for temperture chnges, prevents fogging Low temperture to -35 C Activtion input ctive Trnsmitter ctive/not ctive 8V/ 2V Activtion/disle dely 1ms Input resistnce 10KΩ ±10% 1) In comintion with suitle test monitoring unit, e.g. TNT 35 2) Typ. operting rnge limit: mx. ttinle rnge without performnce reserve 3) Operting rnge: recommended rnge with performnce reserve 4) For UL pplictions: for use in clss 2 circuits only 5) 1=trnsient protection, 2=polrity reversl protection, 3=short circuit protection for ll outputs 6) Rting voltge 250VAC Tles Infrred light 0 50 65 Red light 0 30 39 Operting rnge [m] Typ. operting rnge limit [m] Remrks SLS = Pir consisting of SLSS = Trnsmitter SLSE = SLS 96K/P-1070-T2-2 SLSS 96K-1080-T2-24 SLSE 96K/P-1070-T2-21 SLS 96K/P-1070-T2-4 SLSS 96K-1080-T2-45 SLSE 96K/P-1070-T2-41 SLS 96K/P-1200-T2-2 SLSS 96K-1210-T2-24 SLSE 96K/P-1200-T2-21 SLS 96K/P-1200-T2-4 SLSS 96K-1210-T2-45 SLSE 96K/P-1200-T2-41 SLS 96K/P-1207-T2-2 SLSS 96K-1210-T2-24 SLSE 96K/P-1207-T2-21 SLS 96K/P-1207-T2-4 SLSS 96K-1210-T2-45 SLSE 96K/P-1207-T2-41 SLS 96M/P-1070-T2-2 SLSS 96M-1080-T2-24 SLSE 96M/P-1070-T2-21 SLS 96M/P-1070-T2-4 SLSS 96M-1080-T2-45 SLSE 96M/P-1070-T2-41 SLS 96M/P-1071-T2-2 SLSS 96M-1090-T2-24 SLSE 96M/P-1071-T2-21 SLS 96M/P-1071-T2-4 SLSS 96M-1090-T2-45 SLSE 96M/P-1071-T2-41 SLS 96M/P-1200-T2-2 SLSS 96M-1210-T2-24 SLSE 96M/P-1200-T2-21 SLS 96M/P-1200-T2-4 SLSS 96M-1210-T2-45 SLSE 96M/P-1200-T2-41 SLS 96 M/P - 08 2010/11
Protective throughem photoelectric sensors Order guide 1) Selection tle Order code SLS 96K/P-1070-T2-2 Prt No. 50081292 (Tr) Prt No. 50081293 (Re) SLS 96K/P-1070-T2-4 Prt No. 50031559 (Tr) Prt No. 50031561 (Re) Equipment Housing metl plstic Light source red light (30m) infrred light (50m) Connection terminls M12 connector Fetures optics heting/low temperture ctivtion input filter for multi-xis opertion SLS 96K/P-1200-T2-2 Prt No. 50028009 (Tr) Prt No. 50028010 (Re) SLS 96K/P-1200-T2-4 Prt No. 50028011 (Tr) Prt No. 50028012 (Re) SLS 96K/P-1207-T2-2 Prt No. 50028009 (Tr) Prt No. 50035078 (Re) SLS 96K/P-1207-T2-4 Prt No. 50028011 (Tr) Prt No. 50041109 (Re) SLS 96M/P-1070-T2-2 Prt No. 50025213 (Tr) Prt No. 50025192 (Re) SLS 96M/P-1070-T2-4 Prt No. 50025215 (Tr) Prt No. 50025193 (Re) SLS 96M/P-1071-T2-2 Prt No. 50029454 (Tr) Prt No. 50029455 (Re) SLS 96M/P-1071-T2-4 Prt No. 50080478 (Tr) Prt No. 50080479 (Re) SLS 96M/P-1200-T2-2 Prt No. 50025209 (Tr) Prt No. 50031562 (Re) SLS 96M/P-1200-T2-4 Prt No. 50031249 (Tr) Prt No. 50031250 (Re) 1) Version 2010 A-Z Leuze electronic GmH + Co. KG In der Brike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 SLS 96 M/P - 08 info@leuze.de www.leuze.com
Sfety notices Before using the sfety sensor, risk evlution must e performed ccording to vlid stndrds. For mounting, opertion nd tests, this document s well s ll pplicle ntionl nd interntionl stndrds nd regultions must e oserved, printed out nd hnded to the ffected personnel. Before working with the sfety sensor, completely red nd oserve the documents pplicle to your tsk. In prticulr, the following ntionl nd interntionl legl regultions pply for the commissioning, technicl inspections nd work with sfety sensors: - Mchinery directive 2006/42/EC - Use of Work Equipment Directive 89/655/EEC supplemented y Directive 95/63 EC - Accident-prevention regultions nd sfety rules - Other relevnt stndrds - Stndrds, e.g. ISO 13855 Symols Attention! SLS 96 Wrning sign This symol indictes possile dngers. Plese py especilly close ttention to these instructions! These symols identify the trnsmitter. These symols identify the receiver. Sfety sensor re of ppliction The protective throughem photoelectric sensor is n ctive optoelectronic protective device only in connection with sfetyrelevnt control system, in which the cyclicl testing of trnsmitter nd receiver is crried out in ccordnce with EN 61496-1, up to ctegory 2 nd PL d in ccordnce with EN ISO 13849-1. Attention! The sfety sensor protects persons t ccess points or t points of opertion of mchines nd plnts. The sfety sensor only detects persons upon entry to the dnger re; it does not detect persons who re locted within the dnger re. For this reson, strt-up/restrt interlock is mndtory. No protective function without dequte sfety distnce. The power supply unit used to operte the photoelectric sensor hs to e le to compenste for chnges nd interruptions of the supply voltge cc. to EN 61496-1. Also oserve the sfety notices in the documenttion of the connected test device! Additionl mesures must e tken to ensure tht the AOPD does not experience dngerous filure due to glre from other light sources. Proper use The sfety sensor must only e used fter it hs een selected in ccordnce with the respectively vlid instructions nd relevnt stndrds, rules nd regultions regrding occuptionl sfety nd sfety t work, nd fter it hs een instlled on the mchine, connected, commissioned, nd checked y competent person. Foreseele misuse Any use other thn tht defined under the "Proper use" or which goes eyond tht use is considered improper use. The user must ensure tht no opticl influence on the AOPD occurs through other forms of light ems, e.g. through - wireless control devices on crnes, - rdition from welding sprks, - strooscopic lights. Competent personnel Prerequisites for competent personnel: - He hs suitle technicl eduction. - He knows the instructions for the sfety sensor nd the mchine. - He hs een instructed y the responsile person on the mounting nd opertion of the mchine nd of the sfety sensor. SLS 96 M/P - 08 2010/11
Protective throughem photoelectric sensors Responsiility for sfety Mnufcturer nd opertor must ensure tht the mchine nd implemented sfety sensor function properly nd tht ll ffected persons re dequtely informed nd trined. The mnufcturer of the mchine is responsile for: - Sfe implementtion of the sfety sensor. - Imprting ll relevnt informtion to the opertor. - Adhering to ll regultions nd directives for the sfe commissioning of the mchine. The opertor of the mchine is responsile for: - Instructing the operting personnel. - Mintining the sfe opertion of the mchine. - Adhering to ll regultions nd directives for occuptionl sfety nd sfety t work. - Regulr testing y competent personnel. Sfety distnces Attention! The protective throughem photoelectric sensor must e instlled with the correctly clculted sfety distnce s well s suitle em distnces from potentilly dngerous motion: if n interruption of the light em occurs, the dnger re my only e reched once the mchine hs lredy come to ded stop. c Trnsmitter Deflection mirror 400 mm 900 mm c Bem distnces in ccordnce with ISO 13855 Numer of ems Heights ove reference plne, e.g. floor [mm] Additionl distnce C [mm] 1 750 1200 2 400, 900 850 3 300, 700, 1100 850 4 300, 600, 900, 1200 850 The sfety distnce S etween photoelectric sensor nd dnger re is clculted using the following formul (ISO 13855): S = (K T) + C S: Sfety distnce [mm] etween photoelectric sensor nd dnger re. K: Approch speed (constnt = 1600 mm/s). T: Time dely [s] etween interruption of the light em nd stnd-still of the mchine. C: Sfety constnt (dditionl distnce) = 850mm or 1200mm, see tle ove. Leuze electronic GmH + Co. KG In der Brike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 SLS 96 M/P - 08 info@leuze.de www.leuze.com
Multi-xle instlltion SLS 96 With multi-xle instlltion the light ems hve to run prllel to the reference plne (e.g. floor) nd must e ligned mutully prllel. For this the em direction must e set oppositely in ech cse. Otherwise the light ems could cuse mutul interference nd distur proper functioning. Trnsmitter Distnce to reflecting surfces When mounting, sufficiently lrge distnce from the opticl xis to reflecting surfces must e selected. d 4 c f e 4 c d e f Distnce to the reflecting surfce Protected field width Reflecting surfce Trnsmitter Oject Commissioning Alignment of the sensors Mount photoelectric sensors with corresponding fixing rckets from Leuze electronic. Apply operting voltge to trnsmitter nd receiver nd ctivte trnsmitter vi ctivtion input (see "Electricl connection"). Green LEDs on trnsmitter nd receiver nd yellow LED on trnsmitter illuminte. Position receiver until the yellow LED illumintes. LED links yellow: Light pth free, ut no performnce reserve; clen nd redjust photoelectric sensor, or check operting conditions. Sfety notices for test function 1.To perform testing correctly the ctivtion input of the SLS 96 trnsmitter must e connected to test monitoring unit. 2.The test durtion during ccess protection must not exceed 150ms. 3.Susequent to sensor ctivtion the output switching elements of the test monitoring unit must remin in the 'off' stte for t lest 80ms so tht the downstrem equipment cn e switched off sfely when the photoelectric sensor is used for ccess protection. 4.In order to comply with points 2 nd 3, the use of Leuze electronic test monitoring units (TNT 35, MSI-m) is recommended. SLS 96 M/P - 08 2010/11
Protective throughem photoelectric sensors Check The checks should ensure tht the Optoelectronic Protective Devices hve een used cc. to the ntionl/interntionl regultions, in prticulr in ccordnce with the mchine nd work-equipment directive. Check efore initil commissioning Oserve the ntionlly nd interntionlly vlid regultions. Is the required sfety distnce (protective field of the sfety sensor to the next point of opertion) mintined? Is the sfety sensor effective during the entire dngerous movement nd in ll djustle operting modes of the mchine? It must not e possile to clim over, clim under or circumvent the light pth. Ensure tht the sensor only detects persons upon entry to the dnger re nd does not detect whether persons re locted within the dnger re. Is strt-up/restrt interlock present? Before they egin work, hve competent person trin the operting personnel in their respective tsks. Regulr testing y competent personnel The relile interction of sfety sensor nd mchine must e periodiclly tested in order to detect chnges to the mchine or impermissile tmpering with the sfety sensor. Hve ll tests performed y competent personnel. Oserve the ntionlly nd interntionlly pplicle regultions nd the time periods specified therein. Dily check of the effectiveness of the sfety sensor It is extremely importnt to exmine the effectiveness of the protective field dily so tht it is ensured tht e.g even with djustments to e.g. prmeters, the protective function is ctive t ll points. Interrupt the light em etween the trnsmitter nd receiver (test rod Ø 30mm) - in front of the trnsmitter. - in the middle etween the trnsmitter nd receiver. - in front of nd ehind the deflection mirror. It must not e possile to initite the dngerous stte during em interruption. Disposl For disposl oserve the pplicle ntionl regultions regrding electronic components. Leuze electronic GmH + Co. KG In der Brike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 SLS 96 M/P - 08 info@leuze.de www.leuze.com
SLS 96 M/P - 08 2010/11