Applications Damage service Building drying Water works Dry storing FEATURES

MOBILE DEHUMIDIFIER Function The is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container. Applications Damage service Building drying Water works Dry storing FEATURES Dehumidifier High capacity Low energy consumption Strong and robust cabinet of powder coated hot galvanized steel Epoxy coated evaporator and condenser. Adjustable handle Plastic bumpers Low weight Stackable. Large wheels Water container Water container with handles Automatic stop when water container is full or removed. Permanent drainage can be established with optional ½ hose connection Condensate pump in a cassette as optional extra Electronic control Digital touchpad control panel with display Accurate hour and kwh counter (reading) RH and C monitoring (reading) RH setting Easy fault-finding Service monitoring function Defrosting Active, demand-controlled defrosting which is activated through a temperature sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator. Digital touchpad control panel: 1. On-off switch 2. Reading of room temperature 3. Indicator for normal operation (green lamp) 4. Reading of RH value / setting of RH value 5. Indicator for full water container (yellow lamp) 6. Failure indicator (red lamp) 7. Hour counter / setting of service intervals 8. kwh counter

TECHNICAL DATA Model Operating range humidity 40-100% RH Operating range temperature 3-32 C Air volume 250 m³/h Power supply 230 V/50 Hz Max. ampere consumption 2,7 A Max. power consumption 0,590 kw Refrigerant R 134a Compressor type Rotary Sound level (at 1 metre) 56 db(a) Water container capacity 7 litres Colour cabinet RAL 7044 Colour water container RAL 7015 Colour control panel RAL 9005 Protection class IP X4 Filter PPI 15/G1 Wheel size Ø 250 mm Wheel and water container material PP Control panel material ABS Weight 32 kg CAPACITY CURVES C 35 40% 60% 80% 30 25 20 15 10 5 0 L/H 0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 Specific energy consumption (SEC) 0,45 kwh/l at 30 C & 80% RH 0,81 kwh/l at 20 C & 60% RH Accessories ½ drain outlet Remote hygrostat Wall bracket Dual voltage kit Condensate pump in a cassette (see separate data sheet) DIMENSIONS 427 Also available in this series: (see separate data sheets) 427 427 426 740 736 740 506 506 506 All dimensions are in mm.

MOBILE DEHUMIDIFIER Function The is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container. Applications Damage service Building drying Water works Dry storing FEATURES Dehumidifier High capacity Low energy consumption Strong and robust cabinet of powder coated hot galvanized steel Epoxy coated evaporator and condenser. Adjustable handle Plastic bumpers Low weight Stackable. Large wheels On the back two Ø100 mm flex. air ducts may be connected (max. length of 5 m) (accessory) Built-in 1 kw heating element Supplied with high pressure fan Water container Water container with handles Automatic stop when water container is full or removed. Permanent drainage can be established with optional ½ hose connection Condensate pump in a cassette as optional extra Electronic control Digital touchpad control panel with display Accurate hour and kwh counter (reading) RH and C monitoring (reading) RH setting Easy fault-finding Service monitoring function Digital touchpad control panel: 1. On-off switch 2. Reading of room temperature 3. Indicator for normal operation (green lamp) 4. Reading of RH value / setting of RH value 5. Indicator for full water container (yellow lamp) 6. Failure indicator (red lamp) 7. Hour counter / setting of service intervals 8. kwh counter Defrosting Active, demand-controlled defrosting which is activated through a temperature sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.

TECHNICAL DATA Model Operating range humidity 40-100% RH Operating range temperature 3-32 C Air volume 350 m³/h* Power supply 230 V/50 Hz Max. ampere consumption 2,6 A Max. power consumption with heating element 1,56 kw Max. power consumption without heating element 0,56 kw Refrigerant R 134a Compressor type Rotary Sound level (at 1 metre) 60 db(a)** Water container capacity 7 litres Colour cabinet RAL 7044 Colour water container RAL 7015 Colour control panel RAL 9005 Protection class IP X4 Filter PPI 15/G1 Wheel size Ø 250 mm Wheel and water container material PP Control panel material ABS Weight 34 kg *Measured without air ducts mounted. **Measured with air ducts mounted. CAPACITY CURVES C 35 40% 60% 80% 30 25 20 15 10 5 0 0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 L/H Specific energy consumption (SEC) 0,39 kwh/l at 30 C & 80% RH 0,76 kwh/l at 20 C & 60% RH Accessories ½ drain outlet Remote hygrostat Wall bracket Dual voltage kit Condensate pump in a cassette Flex. air ducts Ø100 mm (see separate data sheet) DIMENSIONS 426 Also available in this series: (see separate data sheets) 426 426 506 506 750 736 750 506 All dimensions are in mm. Material must comply Material to Directive must comply 2002/95/EC to Directive of the European 2002/95/EC Parliament. of the European (RoHS) Parliament. (RoHS) Sheetmetal flatstate Sheetmetal is based on flatstate Dantherm is based A/S process on Dantherm equipment A/S process and is equipment and is Material must comply Material to Regulation must comply (EC) No to Regulation 1907/2006 of (EC) the No European 1907/2006 parliament. of the European (REACH) parliament. only entended (REACH) as a only guide. entended as a guide.

Material Material must must comply comply to Directive to Directive 2002/95/EC 2002/95/EC of the of European the European Parliament. (RoHS) (RoHS) Sheetmetal Sheetmetal flatstate flatstate is based is based on Dantherm on Dantherm A/S process A/S process equipment equipment and is and is Material Material must must comply comply to Regulation to Regulation (EC) (EC) No 1907/2006 No 1907/2006 of the of European the European parliament. parliament. (REACH) (REACH) only only entended entended as a as guide. a guide. Linear Linear dimensions without without tolerances tolerances according according to DS/EN to DS/EN 22768-1 22768-1 medium medium Surface Surface appearance according according to reference to reference BEND BEND RADII: RADII: Angular Angular dimensions without without tolerances: tolerances: ± 1 ± 1 table table LZT 142 LZT 0001, 142 0001, category category 8 8 MATERIAL: REV. REV. BY: BY: 3511 3511 MOBILE DEHUMIDIFIERS CDT TECHNICAL DATA Model Operating range humidity 40-100% RH Operating range temperature 3-32 C Air volume 350 m³/h Power supply 230 V/50 Hz Max. ampere consumption 3,6 A Max. power consumption 0,82 kw Refrigerant R 407C Compressor type Rotary Sound level (at 1 metre) 59 db(a) Water container capacity 14 litres Colour cabinet RAL 7044 Colour water container RAL 7015 Colour control panel RAL 9005 Protection class IP X4 Filter PPI 15/G1 Wheel size Ø 250 mm Wheel and water container material PP Control panel material ABS Weight 43 kg CAPACITY CURVES C 35 40% 60% 80% 30 25 20 15 10 5 0 L/H 0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8 Specific energy consumption (SEC) 0,50 kwh/l at 30 C & 80% RH 0,66 kwh/l at 20 C & 60% RH Accessories ½ drain outlet Remote hygrostat Wall bracket Dual voltage kit Condensate pump in a cassette (see separate data sheet) DIMENSIONS Also available in this series: (see separate data sheets) 545 542 825 823 825 740 736 740 540 540 825 740 545 540 539 All dimensions are in mm.

MOBILE DEHUMIDIFIER Function The is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which is collected in the water container. Applications Damage service Building drying Water works Dry storing FEATURES Dehumidifier High capacity Low energy consumption Strong and robust cabinet of powder coated hot galvanized steel Epoxy coated evaporator and condenser. Adjustable handle Plastic bumpers Low weight Stackable. Large wheels On the back two Ø100 mm flex. air ducts may be connected (max. length of 5 m) (accessory) Built-in 1 kw heating element Supplied with high pressure fan Water container Water container with handles Automatic stop when water container is full or removed. Permanent drainage can be established with optional ½ hose connection Condensate pump in a cassette as optional extra Electronic control Digital touchpad control panel with display Accurate hour and kwh counter (reading) RH and C monitoring (reading) RH setting Easy fault-finding Service monitoring function Digital touchpad control panel: 1. On-off switch 2. Reading of room temperature 3. Indicator for normal operation (green lamp) 4. Reading of RH value / setting of RH value 5. Indicator for full water container (yellow lamp) 6. Failure indicator (red lamp) 7. Hour counter / setting of service intervals 8. kwh counter Defrosting Active, demand-controlled defrosting which is activated through a temperature sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator.

Material Material must comply must comply to Directive to Directive 2002/95/EC 2002/95/EC of the European of the European Parliament. Parliament. (RoHS) (RoHS) Sheetmetal Sheetmetal flatstate flatstate is based is on based Dantherm on Dantherm A/S process A/S process equipment equipment and is and is Material Material must comply must comply to Regulation to Regulation (EC) No (EC) 1907/2006 No 1907/2006 of the European of the European parliament. parliament. (REACH) (REACH) only entended only entended as a guide. as a guide. Linear dimensions Linear dimensions without without tolerances tolerances according according to DS/EN to 22768-1 DS/EN 22768-1 medium medium Surface Surface appearance appearance according according to reference to reference BEND RADII: BEND RADII: Angular Angular dimensions dimensions without without tolerances: tolerances: ± 1 ± 1 table LZT table 142 LZT 0001, 142 category 0001, category 8 8 MATERIAL: MATERIAL: REV. BY: REV. BY: THICKNESS: THICKNESS: DATE: DATE: 3511 3511 Material must com Material must com Linear dimensions Angular dimensio TH UN TH IN W WR ALL AR AN MOBILE DEHUMIDIFIERS CDT TECHNICAL DATA Model Operating range humidity 40-100% RH Operating range temperature 3-32 C Air volume 560 m³/h* Power supply 230 V/50 Hz Max. ampere consumption 3,7 A Max. power consumption with heating element 1,83 kw Max. power consumption without heating element 0,83 kw Refrigerant R 407c Compressor type Rotary Sound level (at 1 metre) 62 db(a)** Water container capacity 14 litres Colour cabinet RAL 7044 Colour water container RAL 7015 Colour control panel RAL 9005 Protection class IP X4 Filter PPI 15/G1 Wheel size Ø 250 mm Wheel and water container material PP Control panel material ABS Weight 46 kg *Measured without air ducts mounted. **Measured with air ducts mounted. CAPACITY CURVES C 35 40% 60% 80% 30 25 20 15 10 5 0 L/H 0 0,2 0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8 2,0 Specific energy consumption (SEC) 0,47 kwh/l at 30 C & 80% RH 0,83 kwh/l at 20 C & 60% RH Accessories ½ drain outlet Remote hygrostat Wall bracket Dual voltage kit Condensate pump in a cassette Flex. air ducts Ø100 mm (see separate data sheet) DIMENSIONS 542 Also available in this series: (see separate data sheets) 542 542 825 823 825 740 736 740 S 540 540 825 740 540 539 All dimensions are in mm.

Material must comply Material to must Directive comply 2002/95/EC to Directive of the 2002/95/EC European of Parliament. the European (RoHS) Parliament. (RoHS) Sheetmetal flatstate Sheetmetal is based flatstate on Dantherm is based A/S on process Dantherm equipment A/S process and equipment is and is Material must comply Material to must Regulation comply (EC) to Regulation No 1907/2006 (EC) of No the 1907/2006 European of parliament. the European (REACH) parliament. only (REACH) entended only as a entended guide. as a guide. Linear dimensions Linear without dimensions tolerances without according tolerances DS/EN according 22768-1 to DS/EN medium22768-1 medium Surface appearance Surface according appearance to reference according to BEND reference RADII: BEND RADII: Angular dimensions Angular without dimensions tolerances: without ± 1 tolerances: ± 1 table LZT 142 0001, table category LZT 142 0001, 8 category 8 MATERIAL: MATERIAL: REV. BY: REV. BY: THICKNESS: THICKNESS: WEIGHT: 99141.12g WEIGHT: 99141.12g DATE: DATE: THIS DRAWING IS FURNISHED THIS DRAWING WITH THE IS FURNISHED WITH THE REF.: ohrref.: ohr UNDERSTANDING THAT UNDERSTANDING THE ESSENCE THAT THE ESSENCE THERE OF WILL NOT BE THERE REPRODUCED OF WILL NOT BE REPRODUCED IN WHOLE OR IN PART IN WITHOUT WHOLE OR IN PART WITHOUT DATE: 25-05-2012 DATE: 25-05-2012 351193 351193 Material must co Material must co Linear dimensio Angular dimens MOBILE DEHUMIDIFIERS CDT TECHNICAL DATA Model Operating range humidity 40-100% RH Operating range temperature 3-32 C Air volume 725 m³/h Power supply 230 V/50 Hz Max. ampere consumption 4,9 A Max. power consumption 1,12 kw Refrigerant R 407c Compressor type Rotary Sound level (at 1 metre) 62 db(a) Water container capacity 14 litres Colour cabinet RAL 7044 Colour water container RAL 7015 Colour control panel RAL 9005 Protection class IP X4 Filter PPI 15/G1 Wheel size Ø 250 mm Wheel and water container material PP Control panel material ABS Weight 47 kg CAPACITY CURVES C 35 40% 60% 80% 30 25 20 15 10 5 0 0 0,5 1,0 1,5 2,0 2,5 3,0 L/H Specific energy consumption (SEC) 0,43 kwh/l at 30 C & 80% RH 0,67 kwh/l at 20 C & 60% RH Accessories ½ drain outlet Remote hygrostat Wall bracket Dual voltage kit Condensate pump in a cassette (see separate data sheet) DIMENSIONS 542 905 820 Also available in this series: (see separate data sheets) 542 542 905 820 905 903 820 816 540 539 All dimensions are in mm. 540 540 CDT MK 60 II MK II

MOBILE DEHUMIDIFIER Function The is a robust, cost-effective and energy-efficient, reliable mobile dehumidifier. It works in accordance with the condensation principle. A fan draws the humid air into the dehumidifier and through an evaporator coil. When passing through the evaporator the air is cooled down to below its dew point temperature, and its content of water vapour is condensed into water, which falls into the drip tray and then is led to the drain. Applications Damage service Building drying Water works Dry storing FEATURES Dehumidifier High capacity Low energy consumption Strong and robust cabinet of powder coated hot galvanized steel Epoxy coated evaporator and condenser. Adjustable handle Plastic bumpers Low weight Large wheels Water drain Fitted with a drain outlet for connection to a ½ water hose Electronic control Digital touchpad control panel with display Accurate hour and kwh counter (reading) RH and C monitoring (reading) RH setting Easy fault-finding Service monitoring function Defrosting Active, demand-controlled defrosting which is activated through a temperature sensor on the evaporator. Defrosting is done by means of hot refrigerant being fed through the evaporator. Digital touchpad control panel: 1. On-off switch 2. Reading of room temperature 3. Indicator for normal operation (green lamp) 4. Reading of RH value / setting of RH value 5. Indicator for full water container (yellow lamp) 6. Failure indicator (red lamp) 7. Hour counter / setting of service intervals 8. kwh counter

Material must comply to Directive Material 2002/95/EC must comply of the to European Directive Parliament. 2002/95/EC (RoHS) of the European Parliament. Sheetmetal (RoHS) flatstate is based on Sheetmetal Dantherm flatstate A/S process is based equipment on Dantherm and is A/S process equipment and is Material must comply to Regulation Material (EC) must No comply 1907/2006 to Regulation of the European (EC) No parliament. 1907/2006 (REACH) of the European only entended parliament. as a (REACH) guide. only entended as a guide. Linear dimensions without tolerances Linear dimensions according without to DS/EN tolerances 22768-1 medium according to DS/EN 22768-1 Surface mediumappearance according Surface to reference appearance BEND according RADII: to reference BEND RADII: Angular dimensions without tolerances: Angular dimensions ± 1 without tolerances: ± 1 table LZT 142 0001, category table 8 LZT 142 0001, category 8 MATERIAL: MATERIAL: REV. BY: REV. BY: THICKNESS: THICKNESS: WEIGHT: 355066.95g DATE: WEIGHT: 355066.95g DATE: 35119 35119 980 Material mus Material mus Linear dimen Angular dim MOBILE DEHUMIDIFIERS CDT TECHNICAL DATA Model Operating range humidity 40-100% RH Operating range temperature 3-32 C Air volume 1000 m³/h Power supply 230 V/50 Hz Max. ampere consumption 7,2 A Max. power consumption 1,64 kw Refrigerant R 407c Compressor type Rotary Sound level (at 1 metre) 62 db(a) Colour cabinet RAL 7044 Colour control panel RAL 9005 Protection class IP X4 Filter PPI 15/G1 Wheel size Ø 250 mm Wheel material PP Control panel material ABS Weight 62 kg CAPACITY CURVES C 35 40% 60% 80% 30 25 20 Specific energy consumption (SEC) 0,42 kwh/l at 30 C & 80% RH 0,71 kwh/l at 20 C & 60% RH DIMENSIONS Accessories Remote hygrostat Dual voltage kit (see separate data sheet) Also available in this series: (see separate data sheets) 980 895 593 980 977 895 894 593 15 10 5 0 L/H 0 0,5 1,0 1,5 2,0 2,5 3,0 3,5 4,0 4,5 593 All dimensions are in mm.

ACCESSORIES CDT Illustration Accessory Description CDT-type Hygrostat When a hygrostat is connected the dehumidifier can operate continuously dependent on the relative humidity in the room. Dantherm No. Two versions are available: Hygrostat with 0,4 m cable, jack plug and fitting Hygrostat with 3 m cable and jack plug All All 396242 396241 ½ draining tap and screwed hose connector Ball tap, brass screwed hose connector and clamp for mounting on the water container All 396243 Condensate pump in a cassette Cassette with built-in condensate pump Vertical lift of up to 3 metres Length of tube: 10 metres CDT 30/30S / 40S/60 075616 075617 Wall bracket Using the wall bracket the dehumidifier can be hung on the wall CDT 30/30S 396247 / 40S/60 396248