Unity 180 Premium Whirlpool 180/80/62 cm Operating and installation instructions Is there a problem with your product or do you have any questions? Please feel free to contact our hotline: 020-8528 1729 1
Index Accessories and sketch 3 Safety instructions 4 Part names 5 Operating the touch displays 6 Installation mounting 7 Care and maintenance 8 Required installation tools 8 2
Ladies and Gentlemen, Thank you for choosing our product. For safety reasons, please take some time to read this manual before installing and starting up carefully. Please open the packaging with suitable tools. Accessories and sketch: 1 x waterfall faucet and gasket 1 x hand shower and hand shower hose Fixing material for the skirt with wall mounting 3
Safety instructions 1. Children and people who require care should not bathe without supervision. Persons with heart problems, high blood pressure or diabetes, and other serious illnesses should use the spa with increased caution or after consulting a physician. 2. Persons with heart problems or high blood pressure are discouraged from using a hot tub. 3. Alcohol consumption or very high physical exhaustion may represent a hazard during use. 4 Do not wipe the surface of the hot tub with hard objects, or heat it, in order to avoid damage to the product. Clean the spa with a soft cloth and neutral detergent. 5 Do not use acidic or alkaline cleaners. 6 When entering and exiting the hot tub, be careful of slipping. 7 Please note that there may be an increased risk of slipping on the tank bottom caused by residue bath additives. 8 All water connections and electrical work (VDE 100/700) must be performed by a specialist. 9 The water pump has dry run protection and can only be placed in operation when the water level sensors are covered with water. 10 The hot tub may not be completely filled. The water pump, air pump and ozone generator need air circulation to ensure that the heat can be dissipated. 4
Part names 1. Back jets 2. Side jets 3. Ground air nozzles 4. Overflow 5. Touch display 6. LED light 7. Outflow 8. Air injection vent 9. Hand shower 10. Waterfall faucet 11. Water inlet valve 12. Hot water 13. Changeover switch 14. Cold water 15. Waterstop 5
Using the touch screen Operating the Touch Display 1. Main switch on/off 2. Air pump on/off 3. Heater on/off 4. Display 5. Adjustment possibilities temperature, radio volume, frequency 6. Radio frequency 7. Radio 8. Key lock on/off 9. Lighting on 10. Ozone disinfection on/off 11. Radio volume 12. Main switch on/off Switching the Whirlpool On/Off and Using the Key lock Function Push the main switch (12). When the whirlpool is turned on, the blue background light of the touch display is visible and the ambient temperature is displayed (4). Each key has a background light. If there is no further activity, the key lock will automatically turn on after one minute. You can turn off the key lock by pressing the Key lock off key for three seconds. Water Pump and Temperature In order to turn the water pump on and off, press the corresponding key (1). If the water level is too low, a symbol will appear on the display (4) and the key (1) will flash. In order to regulate the temperature in the whirlpool, press the heater key (3) when the pool is full and the water pump is running. You can use keys + and - (5) to regulate the temperature. The default temperature when the heater is switched on is 45 C. The adjustable temperature range lies between 25 C and 45 C. Radio Press the radio key (7) once to turn the radio on. When the radio is on, the frequency is shown on the display (4). In order to start the automatic frequency search, press the Radio frequency key (6) for about half a second. To carry out a manual frequency search, press the Radio frequency key (6) and the frequency on the display (4) will start flashing. While the frequency is flashing, you can adjust it using the + and - keys (5). 6
Installation instructions Installation of water connections (before initial use): 1. Secure the hand shower and the waterfall and connect them to the fitting. 2. Connect the hot tub to your water connections. 3. Connect the drain pipe to your sewer connection. First activation (before final assembly): 1. Fill the hot tub with water until the water level sensors (black rectangle on the outside of the tub) are covered. 2. Check all pipes and nozzles for leaks and leave the whirlpool in this state for about 30 minutes. Please do not leave the hot tub unattended during this time and regularly check the tightness of the pipes and nozzles. 3. After point 2 has been completed successfully, please test all functions and let the spa run continuously for 30 minutes. Please leave the hot tub unattended and check tightness of the pipes, nozzles and pumps regularly during this time. 4. Once points1, 2 and 3 have been completed successfully, the final assembly can take place. Final assembly: 1. Put your hot tub in the intended place of use. 2. Now adjust the feet of the hot tub, and pay attention to the horizontal alignment. Also ensure the feet are adjusted so that the skirting fits. 3. Now mount the wall brackets (located in the installation combo kit) which came with the whirlpool. On every side, ensure that the metal brackets are aligned correctly to make sure the hot tub is secured. Attention: Under no circumstances should the tub be used without these wall mountings. Now check the exact height of the hot tub, which must be filled with water at this time and ensure that the height of the feet matches the skirting used. 4. The sides of the hot tub must be sealed to the wall with silicone. 5. Install the skirt, if present. 6. Please wear the head protective gear. 7. Installing the skirting: First attach the skirting holder to the edge of the tub. Next, attach the double angle to the wall. Measure the distance to the floor and make note of it on the skirting. Observe the Quick Start Guide that comes with the KOMBI-Mounting set. 7
Care and maintenance 1. For the daily cleaning of the tub, use a soft cloth and regular household detergent. Please avoid cleaners that contain acetone or ammonia. For disinfection, never use formic acid- or formaldehyde-containing agents. The automatic ozone disinfection kills germs and bacteria. 2. Calcium deposits on the surface can be removed with cleaners, please also refer to page 4, item 5 for more information. 3. For the removal of superficial scratches, we recommend the use of 2000s sandpaper. After which the sanded surface must be polished. 4. If the suction nozzles or jets become clogged with hair etc., they can be unscrewed and cleaned. 1. Measuring tape 2. Wrench (adjustable) 3. Screwdriver 4. Silicone 5. Spirit level 6. Cutting knife Necessary installation tools (not included) 8