SECTION 32 14 00 BRICK PAVERS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2013-2015 ARCAT, Inc. - All rights reserved PART 1 GENERAL 1.1 SECTION INCLUDES A. Pedestrian/light vehicular pavers. B. Heavy vehicular pavers. C. Relieved edge pavers. D. Relieved edge and lugged pavers. E. Danish hand mould pavers. F. Paver step treads. G. Permeable pavers. 1.2 RELATED SECTIONS A. Section 32 13 16.23 - Stamped Concrete Paving. B. Section 32 10 00 - Bases, Ballasts, and Paving. C. Section 09 63 40 - Stone Flooring. 1.3 REFERENCES A. ASTM International, Inc. (ASTM): 1. ASTM C 902 - Standard Specification for Pedestrian and Light Traffic Paving Brick. 2. ASTM C 1272 - Standard Specification for Heavy Vehicular Paving Brick. 1.4 SUBMITTALS A. Submit under provisions of Section 01 30 00 - Administrative Requirements. B. Product Data: Manufacturer's data sheets on each product to be used, including: 1. Preparation instructions and recommendations. 32 14 00-1
2. Storage and handling requirements and recommendations. 3. Cleaning methods. C. Verification Samples: For each product and finish specified, two full-size samples representing actual products, colors and textures. 1.5 QUALITY ASSURANCE A. Manufacturer Qualifications: All primary products specified in this section will be supplied by a single manufacturer with a minimum of ten years experience. B. Installer Qualifications: All products listed in this section are to be installed by a single installer with a minimum of five years demonstrated experience in installing products of the same type and scope as specified. C. Mock-Up: Provide a completely assembled, typical wall areas installed with related accessories, in composite configurations designed to fulfill the performance criteria, and representative of the design as shown on the Drawings. 1. Locate mock-up in location as directed by the Architect. 2. Do not proceed with remaining work until workmanship is approved by Architect. 3. Mock-up area may become part of finished work. 4. Mock-up area may not become part of finished work. 1.6 DELIVERY, STORAGE, AND HANDLING A. Deliver, store and handle materials and products in strict compliance with manufacturer's instructions and recommendations and industry standards. B. Store materials in manufacturer's original sealed, labeled packaging until ready for installation and in accordance with manufacturer's instructions. Protect from damage. 1.7 PROJECT CONDITIONS A. Maintain environmental conditions (temperature, humidity and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits. 1.8 WARRANTY A. Manufacturer's Standard Material Warranty: At project closeout, provide to Owner or Owners Representative an executed copy of the manufacturer's standard limited warranty against manufacturing defect, outlining its terms, conditions, and exclusions from coverage. PART 2 PRODUCTS 2.1 MANUFACTURERS A. Acceptable Manufacturer: Endicott Clay Products Co., which is located at: 57120 707th Rd.; Endicott, NE 68350; Tel: 402-729-3315; Fax: 402-729-5804; Email:request info (endicott@endicott.com); Web:www.endicott.com B. Substitutions: Not permitted. C. Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements. 2.2 PEDESTRIAN/LIGHT VEHICULAR PAVERS 32 14 00-2
A. Pedestrian/Light Vehicular Pavers: Nominal 4 inch x 8 inch brick pavers with wirecut surface 1. Actual Product Size: 4 x 8 x 1-1/4 inches (102 x 203 x 32 mm). 2. Actual Product Size: 4 x 8 x 2-1/4 inches (102 x 203 x 57 mm). 3. Actual Product Size: 3-5/8 x 7-5/8 x 1-1/4 inches (102 x 203 x 32 mm). 4. Actual Product Size: 3-5/8 x 7-5/8 x 2-1/4 inches (102 x 203 x 57 mm). 5. Compliance: ASTM C 902, Class SX, Type 1. 6. Compliance: ASTM C 1272, Type R, application PS. 7. Compliance: ASTM C 1272, Type R, application PX. 8. Compliance: ASTM C 1272, Type F, application PS. 9. Compliance: ASTM C 1272, Type F, application PX. 10. Color: Rose Blend. 11. Color: Red Blend. 12. Color: Burgundy Blend. 13. Color: Bordeaux Blend. 14. Color: Copper Canyon. 15. Color: Coppertone. 16. Color: Medium Ironspot No. 77. 17. Color: Medium Ironspot No. 46. 18. Color: Dark Ironspot. 19. Color: Manganese Ironspot. 20. Pattern: Herringbone 90 degree Pattern 10 ' T' spacers/sf; including perimeter 21. Pattern: Herringbone 45 degree Pattern 10 ' T' spacers/sf; including perimeter 22. Pattern: Running Bond Pattern 10 ' T' spacers/sf; including perimeter 23. Pattern: Basket Weave Pattern 7.5 ' T' spacers/sf and 1.5 ' +' spacers/sf; including perimeter B. Pedestrian/Light Vehicular Pavers: Nominal 8 inch x 8 inch brick pavers with wirecut surface 1. Actual Product Size: 8 x 8 x 2-1/4 inches (203 x 203 x 57 mm). 2. Actual Product Size: 7-5/8 x 7-5/8 x 2-1/4 inches (194 x 194 x 57 mm). 3. Actual Product Size: 7-5/8 x 7-5/8 x 1-1/4 inches (194 x 194 x 32 mm). a. Surface Texture: Finished on five sides, one 8 x 8 inch face unfinished. 4. Compliance: ASTM C 902, Class SX, Type 1. 5. Compliance: ASTM C 1272, Type R, application PS. 6. Compliance: ASTM C 1272, Type R, application PX. 7. Compliance: ASTM C 1272, Type F, application PS. 8. Compliance: ASTM C 1272, Type F, application PX. 9. Color: Rose Blend. 10. Color: Red Blend. 11. Color: Burgundy Blend. 12. Color: Bordeaux Blend. 13. Color: Copper Canyon. 14. Color: Coppertone. 15. Color: Medium Ironspot No. 77. 16. Color: Medium Ironspot No. 46. 17. Color: Dark Ironspot. 18. Color: Manganese Ironspot. 19. Pattern: Herringbone 90 degree Pattern 10 ' T' spacers/sf; including perimeter 20. Pattern: Herringbone 45 degree Pattern 10 ' T' spacers/sf; including perimeter 21. Pattern: Running Bond Pattern 10 ' T' spacers/sf; including perimeter 22. Pattern: Basket Weave Pattern 7.5 ' T' spacers/sf and 1.5 ' +' spacers/sf; including 32 14 00-3
perimeter C. Pedestrian/Light Vehicular Pavers: Nominal 4 inch x 12 inch brick pavers with wirecut surface 1. Actual Product Size: 4 x 12 x 2-1/4 inches (102 x 305 x 57 mm). 2. Actual Product Size: 3-5/8 x 11-5/8 x 2-1/4 inches (92 x 295 x 57 mm). 3. Compliance: ASTM C 902, Class SX, Type 1. 4. Compliance: ASTM C 1272, Type R, application PS. 5. Compliance: ASTM C 1272, Type R, application PX. 6. Compliance: ASTM C 1272, Type F, application PS. 7. Compliance: ASTM C 1272, Type F, application PX. 8. Color: Rose Blend. 9. Color: Red Blend. 10. Color: Burgundy Blend. 11. Color: Bordeaux Blend. 12. Color: Copper Canyon. 13. Color: Coppertone. 14. Color: Medium Ironspot No. 77. 15. Color: Medium Ironspot No. 46. 16. Color: Dark Ironspot. 17. Color: Manganese Ironspot. 18. Pattern: Herringbone 90 degree Pattern 10 ' T' spacers/sf; including perimeter 19. Pattern: Herringbone 45 degree Pattern 10 ' T' spacers/sf; including perimeter 20. Pattern: Running Bond Pattern 10 ' T' spacers/sf; including perimeter 21. Pattern: Basket Weave Pattern 7.5 ' T' spacers/sf and 1.5 ' +' spacers/sf; including perimeter 2.3 HEAVY VEHICULAR PAVERS A. Heavy Vehicular Pavers: Nominal 4 inch x 8 inch brick pavers with wirecut surface texture as manufactured by Endicott Clay Products Co. 1. Actual Product Size: 4 x 8 x 2-5/8 inches (102 x 203 x 67 mm). 2. Compliance: ASTM C 902, Class SX, Type 1. 3. Compliance: ASTM C 1272, Type R, application PS. 4. Compliance: ASTM C 1272, Type R, application PX. 5. Compliance: ASTM C 1272, Type F, application PS. 6. Compliance: ASTM C 1272, Type F, application PX. 7. Color: Rose Blend. 8. Color: Red Blend. 9. Color: Burgundy Blend. 10. Color: Bordeaux Blend. 11. Color: Copper Canyon. 12. Color: Coppertone. 13. Color: Medium Ironspot No. 77. 14. Color: Medium Ironspot No. 46. 15. Color: Dark Ironspot. 16. Color: Manganese Ironspot. 17. Pattern: Herringbone 90 degree Pattern 10 ' T' spacers/sf. 18. Pattern: Herringbone 45 degree Pattern 10 ' T' spacers/sf. 19. Pattern: Running Bond Pattern 10 ' T' spacers/sf. 20. Pattern: Basket Weave Pattern 7.5 ' T' spacers/sf and 1.5 ' +' spacers/sf. 2.4 RELIEVED EDGE PAVERS A. Relieved Edge Pavers: Nominal 4 inch x 8 inch brick pavers with wirecut surface texture as 32 14 00-4
manufactured by Endicott Clay Products Co. 1. Actual Product Size: 4 x 8 x 2-1/4 inches (102 x 203 x 57 mm). 2. Actual Product Size: 4 x 8 x 2-5/8 inches (102 x 203 x 67 mm). 3. Compliance: ASTM C 902, Class SX, Type 1. 4. Compliance: ASTM C 1272, Type R, application PS. 5. Compliance: ASTM C 1272, Type R, application PX. 6. Compliance: ASTM C 1272, Type F, application PS. 7. Compliance: ASTM C 1272, Type F, application PX. 8. Relieved Edges: 1/8 inch x 1/8 inch. 9. Color: Rose Blend. 10. Color: Red Blend. 11. Color: Burgundy Blend. 12. Color: Bordeaux Blend. 13. Color: Copper Canyon. 14. Color: Coppertone. 15. Color: Medium Ironspot No. 77. 16. Color: Medium Ironspot No. 46. 17. Color: Dark Ironspot. 18. Color: Manganese Ironspot. 19. Pattern: Herringbone 90 degree Pattern 10 ' T' spacers/sf; including perimeter 20. Pattern: Herringbone 45 degree Pattern 10 ' T' spacers/sf; including perimeter 21. Pattern: Running Bond Pattern 10 ' T' spacers/sf; including perimeter 22. Pattern: Basket Weave Pattern 7.5 ' T' spacers/sf and 1.5 ' +' spacers/sf; including perimeter 2.5 RELIEVED EDGE AND LUGGED PAVERS A. Relieved Edge/Lugged Pavers: Nominal 4 inch x 8 inch brick pavers with wirecut surface 1. Actual Product Size: 4 x 8 x 2-1/4 inches (102 x 203 x 57 mm). a. Lugs: 1/8 inch (3 mm). 2. Actual Product Size: 4 x 8 x 2-1/4 inches (102 x 203 x 57 mm). a. Lugs: 1/4 inch (6 mm). 3. Actual Product Size: 4 x 8 x 2-5/8 inches (102 x 203 x 67 mm). a. Lugs: 1/8 inch (3 mm). 4. Actual Product Size: 4 x 8 x 2-5/8 inches (102 x 203 x 67 mm). a. Lugs: 1/4 inch (6 mm). 5. Compliance: ASTM C 902, Class SX, Type 1. 6. Compliance: ASTM C 1272, Type R, application PS. 7. Compliance: ASTM C 1272, Type R, application PX. 8. Compliance: ASTM C 1272, Type F, application PS. 9. Compliance: ASTM C 1272, Type F, application PX. 10. Color: Rose Blend. 11. Color: Red Blend. 12. Color: Burgundy Blend. 13. Color: Bordeaux Blend. 14. Color: Copper Canyon. 15. Color: Coppertone. 16. Color: Medium Ironspot No. 77. 17. Color: Medium Ironspot No. 46. 18. Color: Dark Ironspot. 19. Color: Manganese Ironspot. 2.6 HANDICAP DETECTABLE WARNING PAVERS 32 14 00-5
A. Handicap Detectable Warning Pavers: Nominal 4 inch x 8 inch brick pavers with wirecut surface 1. Actual Product Size: 4 x 8 x 1-1/4 inches (102 x 203 x 32 mm). 2. Actual Product Size: 4 x 8 x 2-1/4 inches (102 x 203 x 57 mm). 3. Actual Product Size: 3-5/8 x 7-5/8 x 1-1/4 inches (92 x 194 x 32 mm). 4. Actual Product Size: 3-5/8 x 7-5/8 x 2-1/4 inches (92 x 194 x 57 mm). 5. Surface Protrusions: 8 raised protrusions per paver unit; 0.2 inches (5 mm) in height, tapering from 0.9 inches (23 mm) at the base to 0.75 inches (19 mm). 6. Compliance: ASTM C 902, Class SX, Type 1. 7. Compliance: ASTM C 1272, Type R, application PS. 8. Compliance: ASTM C 1272, Type R, application PX. 9. Compliance: ASTM C 1272, Type F, application PS. 10. Compliance: ASTM C 1272, Type F, application PX. 11. Color: Rose Blend. 12. Color: Red Blend. 13. Color: Burgundy Blend. 14. Color: Bordeaux Blend. 15. Color: Copper Canyon. 16. Color: Coppertone. 17. Color: Medium Ironspot No. 77. 18. Color: Medium Ironspot No. 46. 19. Color: Dark Ironspot. 20. Color: Manganese Ironspot. 21. Pattern: Herringbone 90 degree Pattern 10 ' T' spacers/sf; including perimeter 22. Pattern: Herringbone 45 degree Pattern 10 ' T' spacers/sf; including perimeter 23. Pattern: Running Bond Pattern 10 ' T' spacers/sf; including perimeter 24. Pattern: Basket Weave Pattern 7.5 ' T' spacers/sf and 1.5 ' +' spacers/sf; including perimeter 2.7 DANISH HAND MOULD PAVERS A. Danish Hand Mould Pavers: Nominal 4 inch x 8 inch brick pavers with wirecut surface 1. Actual Product Size: 3-5/8 x 7-5/8 x 2-5/8 inches (92 x 194 x 67 mm). 2. Color: Coppertone. 3. Color: Medium Ironspot No. 77. 4. Color: Medium Ironspot No. 46. 5. Color: Dark Ironspot. 6. Color: Manganese Ironspot. 7. Compliance: ASTM C 902, Class SX, Type 1. 8. Pattern: Herringbone 90 degrees. 9. Pattern: Herringbone 45 degrees. 10. Pattern: Running Bond Pattern. 11. Pattern: Basket Weave Pattern. 2.8 PAVER STEP TREADS A. Paver Step Treads: Brick paver step treads with wirecut surface texture as manufactured by Endicott Clay Products Co. 1. Actual Product Size: 11-5/8 x 3-5/8 x 2-1/4 inches (295 x 92 x 57 mm). 2. Actual Product Size: 7-5/8 x 7-5/8 x 2-1/4 inches (194 x 194 x 57 mm). 3. Radiused Edges: 1/2 inch (12 mm) radius on two adjacent 3-5/8 inch (92 mm) edges. 4. Compliance: ASTM C 902, Class SX, Type 1. 5. Compliance: ASTM C 1272, Type R, application PS. 32 14 00-6
6. Compliance: ASTM C 1272, Type R, application PX. 7. Compliance: ASTM C 1272, Type F, application PS. 8. Compliance: ASTM C 1272, Type F, application PX. 9. Color: Rose Blend. 10. Color: Red Blend. 11. Color: Burgundy Blend. 12. Color: Bordeaux Blend. 13. Color: Copper Canyon. 14. Color: Coppertone. 15. Color: Medium Ironspot No. 77. 16. Color: Medium Ironspot No. 46. 17. Color: Dark Ironspot. 18. Color: Manganese Ironspot. 2.9 PERMEABLE PAVERS A.. 1.. PART 3 EXECUTION 3.1 EXAMINATION AND PREPARATION A. Prepare substrates using the methods recommended by the manufacturer for achieving best result for the substrates under project conditions. B. Do not proceed with installation until substrates have been prepared using the methods recommended by the manufacturer and deviations from manufacturer's recommended tolerances are corrected. Commencement of installation constitutes acceptance of conditions. C. If preparation is the responsibility of another installer, notify Architect in writing of deviations from manufacturer's recommended installation tolerances and conditions. 3.2 INSTALLATION A. Install pavers accordance with manufacturer's instructions and in proper relationship with adjacent construction. 3.3 PROTECTION A. Protect installed products until completion of project. B. Touch-up, repair or replace damaged products before Substantial Completion. END OF SECTION 32 14 00-7