ONV.GL XAMINA i ION C.R i 11-ICA Certificate No: MEDB00000AT Application of: Council Directive 96/98/EC of 20 December 1996 an Marine Equipment as amended by directive 2014/93/EU, issued as "Forskrift om Skipsutstyr" by the Norwegian Maritime Directorate. This Certificate is issued by DNV GL AS under the authority of the Government of the Kingdom of Norway. This is to certify: That the "A" Class divisions, fire integrity with type designation(s) Steel corrugated bulkhead Issued to G+H AG Ludwigshafen am Rhein Rheinland-Pfalz, Germany is found to comply with the requirements in the following Regulations/Standards: Annex A.1, item No. A.1/3.11a and Annex B, Module B in the Directive. SOLAS 74 as amended, Regulation 11-2/3.2.5 and IMO 2010 FTP Code. Further details of the equipment and conditions for certification are given overleaf. I-10vik, 2015-10-19 for DNV GL AS This Certificate is valid until 2020-02-05 Notified Body No.: 0575 G 15i,tJ Vielar Dolonen DNV GL local office: Mar in Gjelstad Head of Department Essen Surveyor G U A LI 18 84.> D N L SJq eße 0 NORWEGIAN ACCREDITAPON PROD 019 The Certificate is subject to terms and conditions overleaf. Any significant changes in design or construction of the product, or amendments to the Directive or Standards referenced above may render this Certificate invalid. The product liability rests with the manufacturer or his representative in accordance with Council Directive 96/98/EC, as amended. The Mark of Conformity may only be affixed to the product and a Declaration of Conformity may only be issued when the production/product assessment module referred to in the council directive, is fully complied with. Form code: MED.Ba Revision: 2015-07 www.dnvgl.com Page 1 of 3 DNV GL 2014. DNV GL and the Horizon Graphic are trademarks of DNV GLAS.
Job Id: 344.1-004262-4 Certificate No: MEDB00000AT Product description "Steel corrugated bulkhead" Composed of a corrugated steel bulkhead made of 2 mm steel core with corrugation dimensions: 58.49x175.47x35 mm, pitch 233.96 mm. The bulkhead is insulated with two layers of mineral wool of type U SeaProtect 66 (density 66 kg/m3) from G+H AG. Each layer is min. 40 mm thick, and is fitted on top of the corrugations with staggered joints. 30 mm thick additional insulation may be fitted inside the corrugation of the bulkhead. The insulation is fasten with 3 mm steel pins and 30 or 38 mm steel washers. Distance between pins is maximum 300 mm. See drawing mentioned under Type Examination documents for further details Application/Limitation Approved for use as a non-loadbearing fire retarding vertical division of Class A-60. Insulation of the same type (U SeaProtect from Saint-Gobain Isover G+H AG) with density up to 86 kg/m3 may be used. The use of this product shall be limited to applications specifically approved by the Administration in question, see IMO 2010 FTP Code part 3, Appendix 1, items 1.12 and 1.13. The construction shall in any case not be used as part of main fire zone bulkheads and stairways enclosures on passenger ships (see also IMO MSC/Circ.1005). The insulation materials and adhesives used have to be approved according to the Marine Equipment Directive and bear the Mark of Conformity. This requirement may also be applicable for surface materials used, if required by relevant rules and regulations. Each product is to be supplied with its manual for installation and maintenance. Type Examination documentation Test report nos. PGA10522 dated 29 September 2014 from Danish Institute of Fire and Security Technology (DBI), Hvidovre, Denmark. Assessment report no. PHA10498c (minimum thickness and density) dated 13 October 2014 and no. PHA10699A (no insulation in corrugation) dated 3 August 2015 both from Danish Institute of Fire and Security Technology (DBI), Hvidovre, Denmark. Drawing no. (6 pages) dated 18 June 2014 from G+H AG. Tests carried out Tested according to IMO 2010 FTP Code part 3. Marking of product The product or packing is to be marked with name of manufacturer, type designation, fire technical rating, the MED Mark of Conformity and USCG A val Number if applicable (see Page 3). is \:45s 64 L'i NZi C51 :301 Form code: MED.Ba Revision: 2015-07 www.dnvgl.com Page 2 of 3 ei
Job Id: 344.1-004262-4 Certificate No: MEDB00000AT Mark of Conformity The manufacturer is allowed to affix the Mark of Conformity according to Article 11 in the Council Directive 96/98/EC on Marine Equipment and shall issue a Declaration of Conformity, only when the module D or E or F of Annex B in the same directive is fully complied with. Module D: Module E: Module F: The quality system for production and testing shall be approved by the Notified Body. The quality system for inspection and testing shall be approved by the Notified Body. Compliance of the products to type as described in this EC Type-Examination Certificate must be verified by the Notified Body who also shall issue a Certificate of Conformity. USCG Approval An U.S. Coast Guard approval number will be assigned to the equipment when the production module has been completed and will appear on the production module certificate (module D, E or F), as allowed by the "Agreement between the United States of America and the EEA EFTA states on the mutual recognition of Certificates of Conformity for Marine Equipment" signed 17 October 2005. Form code: MED.Ba Revision: 2015-07 www.dnvgl.com Page 3 of 3