Floor warming products 2013 V 10.12.2012
DOMOTHERM CLASSIC TWIN/S MAT An ideal solution for the whole house Ultra thin cable (2mm) Energy efficient Easy to install Domotherm Twin/s can be installed under: Tiles, Marble flooring (wet installation) Laminated wooden floors (dry installation) Carpet (dry installation) Other flooring materials that are applicable for floor heating or warming. As "wet installation" (in the tile glue) or "dry installation". Technical data: FWM 2 S 1-975 domoteck Mat output 120W/m 2 150W/m 2 Output Cable 9.6W/lm 12W/lm Voltage 230V Thickness of wire 2.00mm Ribbon width 25mm Protection class/means 1+30mA RCD Supply lead connection One side - twin conductor Base Material Red Fiberglass + Al Spacing 8cm (25% coverage) Supply lead length 2 x 3m The Domotherm Twin/s is manufactured with a screened heating cable which is integrated within a wide thin heating distribution strip. This process offers great advantages such as: Larger percentage of heat transfer over the floor Short setup & response times Desired temperatures reached quickly & efficiently Safe from electrical shock hazards Its flat structure (2mm) minimizes floor elevation and ensures a more uniform distribution of heat. The Domotherm twin/s is designed and manufactured in accordance to the highest safety standards. The Domotherm twin/s can be easily applied to existing floors, ideal for renovations. The Domotherm twin/s is available in two outputs: 120W/m 2, 150W/m 2, Floor Warming Products
DOMOTHERM CLASSIC TWIN/S MAT Technical Applications WET Installation Resistance wire Reinforced insulation 1 2 Adhesive tape Heat Super strong aramid FEP Coating Shielded Braiding distribution strip 3 Plan the layout Attach one of Domoteck s testing instruments a Thermostat Place insulation boards and coat the surface with a primer Spread first layer of tile glue b c Flooring FWM embedded in tile glue Insulation of the building Press down the mat OR Spread second layer of tile glue OPTIONAL To improve efficiency DOMOTECK recommends using insulation boards in your installation a b Thermostat Fix the mat with various fixing means Pour self-leveling concrete 7 8 Flooring FWM installed on insulation boards Place floor covering e.g. tiles Set the thermostat Insulation of the building For full installation details please refer to product installation manual FLOOR WARMING PRODUCTS
DOMOTHERM CLASSIC TWIN/S MAT Technical Applications 1 DRY Installation 2 Resistance wire Reinforced insulation Adhesive tape Heat distribution strip Plan the layout Attach one of Domoteck s testing instruments 3 4 Super strong aramid FEP Coating Shielded Braiding Roll out the CCPE Roll the mat over the CCPE 5 6 Thermostat Flooring Frame the mat with a blind net Place floor covering FWM Installed on CCPE 4mm 7 8 Insulation of the building e.g. carpet Set the thermostat domoteck s warranty policy Domoteck s products are guaranteed by a 10-year Limited Product Warranty, and are designed to safely operate in accordance to the life-span of the application in which they are installed. For full installation details please refer to product installation manual FLOOR WARMING PRODUCTS
TILES WOODEN CARPET DOMOTHERM MAT An ideal solution for the whole house Ultra thin cable (2mm) Energy efficient Easy to install Domotherm Mats can be installed under: Tiles, Marble flooring (wet installation) Laminated wooden floors (dry installation) Carpet (dry installation) Technical data: FWM 1 S 1-970 domoteck Mat output 120W/m 2 150W/m 2 Output Cable 7.5W/lm 9.4W/lm Voltage 230V Thickness of wire 2.00mm Ribbon width 25mm Protection class/means 1+30mA RCD Supply lead connection One side - single conductor Base Material Red Fiberglass + Al Spacing 6.25cm (40% coverage) Supply lead length 3 x 3m The Domotherm Mat is manufactured with a screened heating cable which is integrated within a wide thin heating distribution strip. This process offers great advantages such as: Larger percentage of heat transfer over the floor Short setup & response times Desired temperatures reached quickly & efficiently Safe from electrical shock hazards Its flat structure (2mm) minimizes floor elevation and ensures a more uniform distribution of heat. The Domotherm mat is designed and manufactured in accordance to the highest safety standards. The Domotherm Mat can be easily applied to existing floors, ideal for renovations. The Domotherm Mat is available in Two outputs: 120W/m 2, 150W/m 2, Four widths: 0.50m, 0.75m, 1.00m, 1.50m Floor Warming Products
DOMOTHERM MAT Technical Applications WET Installation Resistance wire Reinforced insulation 1 2 Adhesive tape Heat distribution strip Super strong aramid FEP Coating Shielded Braiding 3 Plan the layout Attach one of Domoteck s testing instruments a Thermostat Place insulation boards and coat the surface with a primer Spread first layer of tile glue b c Flooring FWM embedded in tile glue Insulation of the building Press down the mat OR Spread second layer of tile glue OPTIONAL To improve efficiency DOMOTECK recommends using insulation boards in your installation a b Thermostat Fix the mat with various fixing means Pour self-leveling concrete 4 5 Flooring FWM installed on insulation boards Place floor covering e.g. tiles Set the thermostat Insulation of the building For full installation details please refer to product installation manual FLOOR WARMING PRODUCTS
DOMOTHERM MAT Technical Applications 1 DRY Installation 2 Resistance wire Reinforced insulation Adhesive tape Heat distribution strip 3 Plan the layout Attach one of Domoteck s testing instruments 4 Super strong aramid FEP Coating Shielded Braiding Roll out the CCPE Roll the mat over the CCPE 5 6 Thermostat Flooring Frame the mat with a blind net Place floor covering FWM Installed on CCPE 4mm 7 8 Insulation of the building e.g. carpet Set the thermostat domoteck s warranty policy Domoteck s products are guaranteed by a 10-year Limited Product Warranty, and are designed to safely operate in accordance to the life-span of the application in which they are installed. For full installation details please refer to product installation manual FLOOR WARMING PRODUCTS
CLASSIC MAT Even floor temperatures due to cable spacing (6.25mm) Extra safe-reinforced insulation No air gaps-due to textile mesh Domoteck s Classic Mat is designed with a double insulated cable and sheathed to activate the RDC/GFCI, woven into a textile mesh which will best absorb the tile glue or self leveling concrete. Available in two outputs: 120W/m 2 160W/m 2 for installation Technical data: FWM 2 S 1-813 domoteck Output Mat 120W/m² 160W/m² Output Cable 7.5W/lm 10Wlm Voltage ~032V Last layer of cable PVC Thickness of mat/wire ~3.5mm Protection class/means I + 30mA RCD Connection One side - Twin conductor Cable color Red - Textile 10N Orange Space between heating wires 6.25cm Supply lead length 4.0m Recommended for under: Tiles and natural stone under tiles/natural stone etc. Standard lengths: 2, 4, 6, 8, 10, 12,14 & 16 meters. Floor Warming Products
CLASSIC MAT Technical Applications Installation Reinforced Insulation Shielded Grounding PVC Jacketing 1 2 Resistance Wires Super Strong aramid FEP Coating 3 Plan the layout Attach one of Domoteck s testing instrument a Thermostat Flooring Place insulation boards and coat the surface with a primer b c Spread first layer of tile glue FWM embedded In tile glue Insulation of the building OPTIONAL To improve efficiency DOMOTECK recommends using insulation boards in your installation Using a roller press down the mat a OR Spread second layer of tile glue b Thermostat Flooring Using various fixing means fix the mat to the insulation 4 5 Pour self-leveling concrete FWM installed on insulation boards Insulation of the building Place floor covering e.g. tiles Set the Thermostat For full installation details please refer to product installation manual FLOOR WARMING PRODUCTS
NEW TF-S THERMOFLOOR COMFORT MAT Features & Benefits A streamlined, 0.5m heating mat specially designed for medium and large areas Ultra thin (only 3mm thick) heating wire integrated in textile net for flexibility and effective tile glue absorption Thin wire spacing (85mm) allows for even floor temperatures Reinforced insulation for durability and higher dielectric strength Sticky mat to ensure secure pre-installation layout Simple and quick installation Domoteck s TF-S Thermofloor Economy Mat is designed with a double insulated cable and sheathed to activate the RCD/ GFCI for electrical safety. It is fully integrated into a textile mesh, which will best absorb the tile glue or self leveling concrete. The TF-S Thermofloor Economy Mat : Produced in 0.5m standard width Comes in standard lengths of 2, 3, 4, 5, 6, 8, 10, 12, 14 & 16 meters Available in 150W/m 2 output for installation under tiles etc. TECHNICAL DATA: Output mat Output wire Voltage Last layer of wire Thickness of mat/wire Protection class/means Connection Base material Wire color Space between heating wires Supply lead length FWM 2 S 1-239 DOMOTECK 150W/m² 11.11W/lm ~032V XLPE ~3mm I + 30mA RCD One side White, 10N Textile Sticky Red 74mm 3m Width - Length - Output 150W/ m² m m m² 0.50 2-16 1-8 150-1200 Recommended for under: Tiles and Natural Stone. It is also possible to install it under other floor coverings such as: Parquet, Laminate, Linoleum or Carpets, however, in these cases the mat must be integrated into a 10mm layer of self-leveling concrete. Floor Warming Products
TF-S THERMOFLOOR COMFORT MAT Technical Applications Installation Resistance Wires Reinforced Insulation Shielded Grounding XLPE Jacketing 1 2 Super strong aramid FEP Insulation Plan the layout Attach one of Domoteck s testing instruments 3 4 Thermostat Spread first layer of tile glue Using a roller press down the mat Flooring FWM embedded In 5mm tile glue 5 5 OR Insulation of the building Sub floor Spread second layer of tile glue Pour self-leveling concrete 6 7 Thermostat OPTIONAL DOMOTECK recommends using insulation boards in your installation to improve efficiency Place floor covering e.g. tiles Set the thermostat Flooring FWM installed on insulation boards For full installation details please refer to product installation manual Insulation of the building Optional Installation Set FLOOR WARMING PRODUCTS
THINNEST MAT IVC High level of safety due to IVC (invisible connection) Perfect for renovation ultra thin cable 2.6mm No air gaps due to cable woven in textile mesh Domoteck's Thinnest Mat is assembled as an IVC ("Invisible connection") enabling the element to be 100% water proof, providing an optimal level of safety particularly in wet locations. TECHNICAL DATA: Output Mat Output Cable Voltage Last layer of cable Thickness of the mat wire Protection class/means Connection Cable Color Space between heating wires Supply Lead Length FWM 1 B 1-871 DOMOTECK 120W/m² 160W/m² 7.5W/lm 10W/lm ~230V PA ~2.6mm 1+ 30mA RCD Two side connection IVC Transparent- Orange 6.25cm 2 x 3.0m Recommended for under: Tiles and natural stone although it can be installed under other floor coverings such as: parquet, laminate, linoleum or carpets, in these cases the mat must be integrated into a 10mm layer of self-leveling concrete. The Thinnest Mat s cable is woven into a textile mesh allowing the system to be totally embedded in the tile glue/self leveling concrete. An ultra thin cable (2.6mm) making it the perfect product for renovation in both residential & commercial properties. The Thinnest Mat is available in standard lengths: 2, 4, 6, 8, 10, 12, 14 & 16 meters. Floor Warming Products
THINNEST MAT IVC Technical Applications Installation Braided Grounding Polyamide jacketing 1 2 Reinforced Resistance Wires Insulation Super Strong aramid FEP Insulation 3 Plan the layout Attach one of Domoteck s testing instruments a Thermostat Place insulation boards and coat the surface with a primer Spread first layer of tile glue b c Flooring FWM embedded In 5mm tile glue Sub floor Insulation of the building Using a roller press down the mat a OR b Spread second layer of tile glue Thermostat OPTIONAL DOMOTECK recommends using insulation boards in your installation to improve efficiency Using various fixing means fix the mat to the insulation boards 4 5 Pour self-leveling concrete Flooring FWM installed on insulation boards Insulation of the building Place floor covering e.g. tiles Set the thermostat For full installation details please refer to product installation manual FLOOR WARMING PRODUCTS
ALUMINUM MATTWIN/S The Aluminum Mat Twin/S cable is Extra safe due to screened cable Perfect heat transfer due to aluminum foil screened, meaning the electrical wire is doubly insulated to withstand 4,000V. In addition, the copper wires are wrapped around a double insulated heating wire, which becomes a sensor activating the RCD/ GFCI in case of mechanical or thermal malfunctions. Technical data: Output Mat Output Cable Voltage Last layer of cable Thickness of the mat wire Protection class/means Connection Cable Color Space between heating wires Supply Lead Length FWM 2 S 1-536 domoteck 100W/m² 150W/m² 5.0 W/lm 7.5W/lm ~230V Screened ~2.0 mm 1 + 30mA RCD + Aluminum Foil One side - Twin conductor Silver - White Textile + Aluminum Foil 5cm 0.2m The aluminum foil allows an even heat distribution across the entire floor. The Aluminum Mat Twin/S is designed for a dry no-fuss installation under wooden flooring, and can also be installed over most existing hard floor surfaces such as tiles. Available in two outputs: 100W/m² for well insulated floors (e.g. wooden, carpet) 150W/m² for poorly insulated floors Recommended for under: Parquet & laminates. (e.g. stone, concrete) Floor Warming Products
ALUMINUM MAT TWIN/S Technical Applications Installation Resistance Wires Reinforced Insulation Shielded Grounding 1 2 Super Strong aramid FEP Coating Plan the layout Attach one of Domoteck s testing instruments 3 4 Domoteck can supply the insulation CCPE (closed polyethylene cell ) in Rolls of 1 x 10M OR Roll out the CCPE Roll the AL-Mat over the CCPE Tiles 0.50 x 0.50 5 6 For leveling the installation Domoteck can also supply the blind net in rolls of 0.50M x 10M 5m 2 Frame the Al-mat with a blind net Place floor covering 7 Thermostat Set the thermostat For full installation details please refer to product Flooring installation manual FWM Installed on CCPE 4mm Insulation of the building FLOOR WARMING PRODUCTS
FS-ALUMINUM MAT Fixed size-simplifies planning & installation The FS Aluminum Mat is specially designed as a fix sized mat to simplify the planning and installation process for both installers & DIY alike. The FS Aluminum Mat must be connected to the main electric box through an RCD (30mAMps) which not only protects the warming element but also increases personal Technical data: FWM 1 N 1-510 domoteck Output mat 100W/m² 150W/m² Output cable 5W/lm 7.5/lm Voltage ~230V Last layer of cable PA Thickness of mat wire ~2.0mm Protection class/means 1 + 30mA RCD + aluminum foil Connection One side - Single conductor Cable color Silver-White Textile + Aluminum Foil Space between heating wires 5.0cm Supply lead length 2x3m + Earthing wires Recommended for under: Parquet & Laminates. safety. To enable easier installation the FS Aluminum Mat has a single cable, assembled with a one point connection to the electrical wiring system of the building. Perfect heat distribution due to the aluminum foil. Recommended for under: Wooden floors. The Fixed Size Aluminum Mat is available in: Two outputs: 100W/m 2, 150W/m 2 Fixed size width: 0.50m Floor Warming Products
FS-ALUMINUM MAT Technical Applications Installation Resistance Reinforced insula- 1 2 Super strong aramid FEP Coating Plan the layout Attach one of Domoteck s testing instruments Domoteck can supply the insulation CCPE (closed polyethylene cell ) in 3 4 Rolls of 1 x 10M OR Tiles 0.50 x 0.50 For leveling the installation Domoteck can also supply the blind net in rolls of 0.50M x 10M 5m 2 Roll out the CCPE 5 6 Roll the AL-mat over the CCPE Frame the Al-mat with a blind net Place floor covering Thermostat Thermostat 7 Flooring Wooden FWM Installed on 4mm layer of CCPE Set the thermostat For full installation details please refer to product Insulation of the building installation manual FLOOR WARMING PRODUCTS
ALUMINUM MAT SINGLE/S Screened cable-extra safe Perfect heat transfer-due to aluminum foil The Aluminum Mat-Single/S cable is screened meaning the electrical wire is doubly insulated to withstand 4,000V, plus the copper wires are wrapped around a double insulated heating wire which becomes a sensor activating the RCD/GFCI in case of mechanical or thermal malfunctions. The Aluminum Mat-Single/S is a special floor warming element designed for dry Technical data: Output Mat Output Cable Voltage Last layer of cable Thickness of the mat wire Protection class/means Connection Cable Color Space between heating wires Supply Lead Length FWM 1 S 1-531 domoteck 100W/m² 150W/m² 5.0 W/lm 7.5W/lm ~230V Screened ~1.8 mm 1 + 30mA RCD + Aluminum Foil Two side - Single conductor Silver - White Textile + Aluminum Foil 5cm 2 x 0.2m + Earthing wires installation under wooden flooring. Can be installed over any existing hard flooring surface, such as tiles, self-leveling concrete, stone etc. No fuss - dry installation. Perfect heat distribution due to the aluminium foil. Suitable for under: Parquet and Laminate. Recommended for under: Parquet & laminates. Floor Warming Products
ALUMINUM MAT SINGLE/S Technical Applications Installation Resistance wire Reinforced Shielded 1 2 Super strong FEP Coating Plan the layout Attach one of Domoteck s testing instruments Domoteck can supply the insulation CCPE (closed polyethylene cell ) in 3 4 Rolls of 1 x 10M OR Tiles 0.50 x 0.50 For leveling the installation Domoteck can also supply the blind net in rolls of 0.50M x 10M 5m 2 5 Roll out the CCPE Roll the AL-mat over the CCPE 6 Frame the Al-mat with a blind net Place floor covering 7 Thermostat Set the thermostat Flooring FWM Installed on CCPE 4mm For full installation details please refer to product installation manual Insulation of the building FLOOR WARMING PRODUCTS
ALUMINUM CCPE FS Fixed size-simplifies planning & installation Already stuck to CCPE insulation The Aluminum CCPE FS Mat is specially designed as a fix sized mat to simplify the planning and installation process for both installers & DIY alike. The Aluminum CCPE FS Mat consists of an aluminium mat previously bonded on an insulating layer of CCPE to enable easier installation. Technical data: Output mat Output cable Voltage Last layer of cable Thickness of mat wire Protection class/means Connection Base material Cable color Space between heating wires Supply lead length FWM 1 N 1-945 domoteck 120W/m² 6W/lm ~230V PA ~2.0mm 1 + 30mA RCD One side connection Textile+ Aluminum Foil + CCPE Transparent 5.0cm 2x2m + Earthing wires The Aluminum CCPE FS Mat must be connected to the main electric box through an RCD (30mAMps) which not only protects the warming element but also increases personal safety. To enable easier installation the Aluminum CCPE FS Mat has a single cable, assembled with a one point connection to the electrical wiring system of the building. Perfect heat distribution due to the aluminum foil. Recommended for under: Wooden floors. Fix size width: 0.50m Recommended for under: Parquet & laminates. Floor Warming Products Copyright 2006-2012 All rights reserved. www.decoragroup.com www.domoteck.com & all related companies. The materials in this page, may not be
ALUMINUM CCPE FS Technical Applications Installation Resistance Reinforced insula- 1 2 Super strong aramid FEP Coating Plan the layout Attach one of Domoteck s testing instruments For leveling the installation Domoteck can also supply the blind net in rolls of 0.50M x 10M 5m 2 3 4 Roll out the AL-mat Frame the Al-mat with a blind net 5 6 Thermostat Place floor covering Set the thermostat For full installation details please refer to product Flooring Wooden FWM installation manual Insulation of the building FLOOR WARMING PRODUCTS
Underfloor warming Mats & cables for Bathroom
TFM-S THERMOFLOOR COMFORT KIT Domoteck s basic packaging includes: Heating mat suitable for an area up to 6 m 2 Thermostat CU345 pipe Angle Optional testing equipment However, when the area to be heated is larger than 6m 2 and a mat from the basic packaging is not enough for coverage, Domoteck offers you the perfect solution! A supplementary mat can be purchased and used to perfectly cover the area to be heated. Both mats (the basic and the supplementary one) : 0.3m heating mat specially designed for small & medium areas Narrow cable spacing (85mm) allows for even floor temperatures Ultra thin (only 3mm thick) and reinforced (double) insulated heating cable for higher safety and durability Textile net allows for flexibility and absorbing of tile glue Sticky mat enables a pre-setting of the heating element in the area to be heated Double insulated cable and sheathed to activate the RCD/GFCI TECHNICAL DATA: FWM 2 S 1-239 DOMOTECK Output mat 150W/m² Output cable 11.11W/lm Voltage ~230V Last layer of cable XLPE Thickness of mat/wire ~3mm Protection class/means I + 30mA RCD Connection One side Base material White, 10N PP Sticky Cable color Red Space between heating wires 74mm Supply lead length 3m Recommended for under: Tiles and natural stone. It is also possible to install it under other floor coverings such as: parquet, laminate, linoleum or carpets, however, in these cases the mat must be integrated into a 10mm layer of self-leveling concrete. Basic mat s lengths and outputs / m 2 : Width - Length - Output m m 150W/m 2 0.30 4-20 1.20-6.00 180-900 m 2 Supplementary mat s lengths and output / m 2 : Width - Length - Output m m 150W/m 2 0.30 12-20 3.60-6.00 540-900 m 2 Floor Warming Products
TFM-S THERMOFLOOR COMFORT KIT Technical Applications Installation Resistance Wires Reinforced Insulation Shielded Grounding XLPE Jacketing 1 2 Super strong aramid FEP Insulation Plan the layout Attach one of Domoteck s testing instruments 4 Thermostat installed on outside bathroom wall Spread first layer of tile glue Using a roller press down the mat Flooring 5 5 FWM embedded In 5 mm tile glue Insulation of the building OR Spread second layer of tile glue Pour self-leveling concrete Thermostat installed on outside bathroom wall OPTIONAL DOMOTECK recommends using insulation boards in your installation to improve efficiency 6 7 Place floor covering e.g. tiles Set the thermostat Flooring FWM installed on insulation boards Insulation of the building For full installation details please refer to product installation manual FLOOR WARMING PRODUCTS
TFM-S THERMOFLOOR COMFORT KIT Basic packaging with 0.30 m width & 4-20 m length mat Optional testing equipment Multimeter Supplementary packaging with 0.30 m width & 12-20 m length mat FLOOR WARMING PRODUCTS
TFC-S COMFORT KIT Loose cable Extra safe-reinforced insulation Ideal for complicated areas Domoteck s basic packaging includes: Loose Cable Thermostat CU 345 pipe Angle + AL adhesive tape Technical data: Output Cable 10W/lm Voltage ~230V Last layer of cable XLPE Thickness of wire ~3.0mm Protection class/means I + 30mA RCD Connector One side Cable Color red Supply Lead Length 3.0m FWC 2 S 1-670 domoteck The max. power should be 1600W/Unit n order not to exceed 10mG EMF. Recommended for under: Tiles and natural stone Domoteck s TFC-S Loose cable is designed with a double insulation and is sheathed to activate the RDC/GFCI, in cases of mechanical faults. Domoteck s TFC-S Loose cable is an ideal under floor warming system for awkward and complex areas, such as bathrooms. Suitable for both renovation and new construction projects. The TFC-S Loose cable may be secured to the substrate using aluminum clips and spacers, or alternatively with adhesive strips. Different anchoring means are available. Distances cm W/lm Cable needed for 1m 2 W/m 2 5 (2*2.5cm) 10 20 200 6 (2*3cm) 10 16.6 166 7.5 (3*2.5cm 10 13.3 133 9 (3*3cm 10 11.1 111 10 (4*2.5cm) 10 10 100 Floor Warming Products
TFC-S COMFORT KIT Loose cable Technical Applications Installation Resistance Wires Reinforced Insulation Shielded Grounding XLPE Jacketing 1 2 Super strong aramid FEP Insulation 3 Plan the layout Attach one of Domoteck s testing instrument 4 Thermostat installed on outside bathroom wall Place insulation boards and coat the surface with a primer 5 If using the insulation fix the anchoring means down onto the boards Flooring FWC embedded In tile glue Insulation of the building OPTIONAL To improve efficiency DOMOTECK recommends using Insulation boards in your installation Fix the cable into the anchoring means 6 OR 7 Thermostat installed on outside bathroom wall Spread a layer of tile glue Pour self-leveling concrete 8 9 Flooring FWC installed on insulation boards Insulation of the building Place floor covering e.g. tiles Set the thermostat For full installation details please refer to Product installation manual FLOOR WARMING PRODUCTS
SHOWER MAT High level of safety due to IVC (invisible connection) Supply leads exit from one point enabling easier installation Technical data: FWM 1 B 2-540 domoteck Output Mat 200W/m² Output Cable 16W/lm Voltage ~230V Last layer of cable PVC Thickness of the mat wire ~ 4.3mm Protection class/means I + 30mA RCD Connection Two side - IVC - Single conductor Cable Color Yellow - Grey fiberglass Space between heating wires 8cm Supply Lead Length 2 x 3.0m Recommended for under: Tiles and natural stone Domoteck s Shower Mat is assembled as an IVC ("Invisible connection") enabling the element to be 100% water proof, providing an optimal level of safety particularly in wet locations. The Shower Mat s supply leads are exiting from the same place allowing for an easier connection to the electrical wiring system of the building. Domoteck s Shower Mat - Is an underfloor warming element specifically designed for the shower cubicle, created to make your shower experience complete. The Shower Mat should be connected to the same thermostat that operates the under floor warming system in the bathroom's dry area. The thermostat has an option to disconnect the Shower Mat if so desired. According to IEC 335/296 the heating element must be installed in the floor Floor Warming Products
Size: 80cm x 80cm. SHOWER MAT Technical Applications Installation Braided Grounding PVC jacketing 1 2 Resistance Wires Reinforced Insulation Super Strong aramid FEP Coating 3 Clean the sub floor Attach one of Domoteck s testing instrument 4 Thermostat installed on outside bathroom wall Spread first layer of tile glue 5 6 Press down the mat Flooring tiles or natural stone FWM embedded In tile glue Spread second layer of tile glue OR Pour self-leveling concrete Insulation of the building For full installation details please refer to product installation manual FLOOR WARMING PRODUCTS
EASY FIT Perfect for D. I. Y. you don t have to be a professional Easy installation- just place, stretch & fasten Domoteck grippers: an easy way to fix the mat Domoteck's Easy Fit cable is woven into three elasticated strips extending up to 25% of its original length enabling an easier installation, just place stretch & fasten. Before, you had to drill holes in the floor. Now, thanks to Domoteck grippers, you can easily fix the mat to the floor. You just have to remove the paper from the bottom of the gripper and to fix it to the floor. Insert the grippers into the elastic strips of the mat, stretch the mat and fix the end of the mat to others grippers. Technical data: FWM 2 S 1-559 domoteck Output Mat 160W/m² to 120W/m² Output Cable 10W/lm Voltage ~230V Last layer of cable PVC Thickness of the mat wire ~ 3.5mm Protection class/means I + 30mA RCD Connection One side - Twin conductor Cable Color White - Red textile strips Space between heating wires 6.25cm to 7.8cm (stretchable) Supply Lead Length 4m Recommended for under: Tiles and natural stone The Easy Fit with its stretchable design allows coverage of the selected floor area simply & efficiently. Can be customized on site Easy Fit is available in 0.30m and 0.50m, especially for the bathroom. Please note: When stretching the Easy Fit Mat, take into account the output per m 2 will change. The heating mat output can range between 160W/m² to 100W/m² Therefore adjustments will have to be made accordingly. Floor Warming Products
EASY FIT Installation Technical Applications 1 2 Resistance Wires Reinforced Insulation Shielded Grounding PVC Jacketing Super strong aramid FEP Coating 3 Plan the layout. Mark position of the grippers on the sub floor. If using more than one mat, mark the end of one and strart of another 4 Attach one of Domoteck s testing instrument Thermostat installed on outside bathroom wall Flooring tiles or natural stone Place insulation boards and coat the surface with a primer Fix the grippers on the floor and insert them into the elastic strip. Then close the tab on the strip. FWM embedded 5 6 7 Insulation of the building OPTIONAL To improve efficiency DOMOTECK recommends using Insulation boards in your installation Thermostat installed on outside bathroom wall Attach the end of the elasticated strips to the grippers and stretch the mat 8 9 OR Attach the end of the elasticated strips to the grippers Flooring FWM installed on insulation boards Insulation of the building Spread a layer of tile glue 10 11 Pour self-leveling concrete domoteck s warranty policy Domoteck s products are guaranteed by a 10-year Limited Product Warranty, and are designed to safely operate in accordance to the life-span of the application in which they are installed. Place floor covering e.g. tiles Set the Thermostat For full installation details please refer to product installation manual FLOOR WARMING PRODUCTS
THIN BRAIDED CABLE High level of safety due to IVC (invisible connection) Perfect for renovation due to ultra thin cable 2.6mm Domoteck s Thin Braided Cable is assembled as an IVC ("Invisible connection") enabling the element to be 100% water proof, providing an optimal level of safety particularly in wet locations. Technical data: FWC 1 B 1-681 domoteck Output Cable 10W/lm Voltage ~230V Last layer of cable PA Thickness of wire ~2.6mm Protection class/means 1 + 30mA RCD Connection Two side - IVC - Single conductor Cable Color Orange Supply Lead Length 2 x 4.0m The max. power should be 1600W/Unit in order not to exceed 10mG EMF. Recommended for under: Tiles and natural stone Domoteck s Thin Braided Cable is designed with braiding tinned copper which wraps the insulated heating wires and gives more electrical safety and mechanical strength enabling normal leakage current to go to the ground and activates the RCD in case mechanical fault. The Thin Braided Cable is the thinnest cable (2.6mm) in Domoteck s range making it the perfect product for renovation. Distances cm 5 (2*2.5cm) 6 (2*3cm) 7.5 (3*2.5cm 9 (3*3cm W/lm 10 10 10 10 Cable needed for 1m 2 20 16.6 13.3 11.1 W/m 2 200 166 133 111 For optimal customization the Thin Braided Cable may be secured to the substrate using Aluminium clips and spacers, or alternatively with adhesive strips. Different anchoring means are available. 10 (4*2.5cm) 10 10 100 Floor Warming Products
THIN BRAIDED CABLE Technical Applications 1 Installation 2 Resistance Wires Reinforced Insulation Braided Grounding Polyamide Jacketing Super Strong FEP Plan the layout Attach one of Domoteck s testing instrument aramid Coating 3 4 Thermostat installed on outside bathroom wall Flooring Tiles or Natural FWC embedded In tile glue Insulation of the building Place insulation boards and coat the surface with a primer 5 If using the insulation fix the anchoring means down onto the boards If not fix the anchoring means to the sub floor Fix the cable into the anchoring means Thermostat installed OPTIONAL 6 7 To improve efficiency DOMOTECK recommends using Insulation boards in your installation Flooring tiles or natural stone FWC installed on insulation Spread a layer of tile glue OR Pour self-leveling concrete Insulation of the build- 8 9 domoteck s warranty policy Domoteck s products are guaranteed by a 10-year Limited Product Warranty, and are designed to safely operate in accordance to the life-span of the application in which they are installed. Place floor covering e.g. tiles Set the Thermostat For full installation details please refer to product installation manual FLOOR WARMING PRODUCTS
CLASSIC CABLE Extra safe-reinforced insulation Ideal for complicated areas Domoteck s Classic Cable is designed with a double insulation and is sheathed to activate the RDC/GFCI, in cases of mechanical Technical data: FWC 2 S 2-645 domoteck Output Cable 10W/lm Voltage ~230V First layer FEP Last layer of cable PVC Thickness of wire ~4.5mm Protection class/means I + 30mA RCD Connector One side - Twin conductor Cable Color Green Supply Lead Length 4.0m The max. power should be 1600W/Unit n order not to exceed 10mG EMF. Recommended for under: Tiles and natural stone faults. Domoteck s Classic Cable is an ideal under floor warming system for awkward and complex areas, such as bathrooms. Suitable for both renovation and new construction projects. The Classic Cable may be secured to Distances cm W/lm Cable needed for 1m 2 W/m 2 the substrate using aluminum clips 5 (2*2.5cm) 10 20 200 and spacers, or alternatively with 6 (2*3cm) 7.5 (3*2.5cm 9 (3*3cm 10 10 10 16.6 13.3 11.1 166 133 111 adhesive strips. Different anchoring means are available. 10 (4*2.5cm) 10 10 100 Floor Warming Products
CLASSIC CABLE Installation Technical Applications Resistance wires Shielded Grounding Reinforced Insulation PVC Jacketing 1 2 Super Strong aramid FEP Coating 3 Plan the layout Attach one of Domoteck s testing instrument 4 Thermostat installed on outside bathroom wall Flooring tiles or natural stone FWC embedded In tile glue Insulation of the building OPTIONAL To improve efficiency DOMOTECK recommends using Insulation boards in your installation Place insulation boards and coat the surface with a primer 5 Fix the cable into the anchoring means 6 OR 7 If using the insulation fix the anchoring means down onto the boards Thermostat installed on outside bathroom wall Spread a layer of tile glue Pour self-leveling concrete 8 Flooring tiles or natural stone FWC installed on insulation boards Insulation of the building Place floor covering e.g. tiles Set the thermostat For full installation details please refer to Product installation manual FLOOR WARMING PRODUCTS
Accessories for Mats & Cables Product Name Article No. Application Tube for 12m 1.5m 9721 440 219 Installation of Thermostat 90 0 C Angle AC 704 9721 440 218 Fixing Tube in place 8-12 Installation Kit AC 718 Including pipe 14/2 + angle + corrugated 2.5m + electrical box 9725 470 095 Installation of control unit CCPE Insulation Layer AC 705 1x20 9721 440 089 Installation under the Aluminum Mat CCPE Insulation Tiles AC 705 9721 440 194 Installation under the Aluminum Mat 0.50 x 0.50-6 units 1.5m2 Blind Net AC 707 0.5x10 9721 440 001 To be framed around the Aluminum mat to level off the floor height Plastic Nails AC 714 9721 440 136 Fixing mats into place
Accessories for Mats & Cables Product Name Article No. Application Aluminum adhesive tape 9721 440 199 For fixing cable to the sub floor 50m Fixing Strip Aluminum 9721 440 104 9721 440 110 For Cables - 3.3mm Spacing loops - 25mm Spacing loops - 30mm Fixing Strip Aluminum Length 1m 9721 440 123 For Cables Spacing loops - 50mm ECC 3 (electrical connection chain) 9721 440 894 ECC-connection ECC 5 (electrical connection chain) 9721 440 895 ECC-connection Grippers To fix the Easy fit mat to the floor
Contact Information: info@domoteck.com www.domoteck.com