TM AFTER-SALES SERVICE (Including Spare Part Request) 1800-282-093 603-6286 9000 www.rubine.com.my WARRANTY: Standard 1-year warranty on manufacturing defects. 5-year warranty on cooking hood motor. PRODUCT WARRANTY REGISTRATION: Log on to www.rubine.com.my for product warranty registration and more information on the terms and conditions. Please refer to the serial number labeled on product body or carton box for warranty registration. RCH-IA90SV-GX RCH-IA90SM-GX This specification is subject to change without notice. FIAMMA TRADING SDN. BHD. will not be held responsible for the use of superseded or voided specifications. Fabricator must check for cut-out accuracy. COOKER HOOD FIAMMA TRADING SDN BHD(330476-P) 9-2, Wisma Fiamma No. 20 Jalan 7A/62A, Bandar Manjalara 52200 Kuala Lumpur, Malaysia Tel: 603-6279 8943 Fax: 603-6279 8942
READ AND SAVE THESE INSTRUCTIONS MANUAL CONTENTS TECHNICAL CHARACTERISTICS... 1 BODY SIZE... 1 MAIN PARTS NAME...2-3 INSTALLATION REQUIREMENT...4 INSTALLATION PROCEDURES...4-6 OPERATION INSTRUCTION... 7 MAINTENANCE...8 TO REPLACE LIGHT BULB...8 PARTS REPLACEMENT...9-10 IMPORTANT SAFETY INSTRUCTIONS...11-12 TROUBLE SHOOTINGS...13 Please note that this product is marked with this symbol: According to Waste of Electrical and Electronic Equipment (WEEE) directive, WEEE should be separately collected and treated. If at any time in future you need to dispose of this product, Please do NOT dispose of this product with house hold waste. Please send this product to WEEE collecting points where available. TROUBLE SHOOTINGS CAUTION: Disconnect the power supply before servicing. STATUS CAUSE AND METHOD OF REPAIRING TOOL The power supply is damaged The lamp works but the motor does not run The lamp works but the motor does not run Machine vibration Weakness suction Installation of the model is tilt If the power supply is damaged,please call the technicians to repair. a) Remove the vane guard and rotate the vane by hand,if the vane cannot move smoothly, the core or bearings of the motor may be damaged. In this case, replace with a new motor. b) If the motor stops running and has a bad odor after a moment of operation, the motor wires may be burnout. Replace the motor. c) If the starting wire (yellow) is disengaged from the condenser, it needs to be rewired. d) If the condenser is damaged, replace with a new one. a) Take off the filter and check the connection between air inlet and wind chamber is sealed or not. b) Check the connection between air exhaust pipe and wind chamber leaks oil or not. If"YES, please fill it up with the varnish or the thinner. a) If the motors were not firmly screwed, screw tigh -ten them up. b) If the vane is damaged or unbalanced, replace with a new one. a) The distance is too far between the Hood and the Gas Cooker. b) There are many windows (doors) cause wind con -vection is too strong. c) Because of the Hood is set upon the window, the best solution is that put one three-ply board on the back of the Hood for covering the hollow of window. a) Adjust the height of the model where is hang on the ceiling. b) If the model tilt forward, lock into the wall with wood screw again (the screw peep out around 0.5 ~1 cm from the wall), or check the screws for fix -ing the model are loose or not. Sharp Pincers Bulb does not light Just screw off the lamp shade and replace with a new bulb,then put the lamp shade back. 13
Dear consumer, Thanks for your purchase of our cooker hood and we hope we can fully satisfy all of your needs. Please read entire instructions carefully before proceeding to obtain the best results of using the cooker hood. TECHNICAL CHARACTERISTICS MODEL NO.: RCH-IA90SV-GX, RCH-IA90SM-GX Never wash the control switch with water or other kind of liquid to avoid the liquid might cause electrical problem to the hood. TOTAL POWER: 204 W 6 SPEED MOTOR: 200W LED Lights:12V d.c / 2 2W VOLTAGE: 220V 240V FREQUENCY: 50HZ CONTROL: Multi-functional sensor switch BODY SIZE 32 0 39 0 436 465 Never pull the plug out of the power supply by wet hand to avoid the possibility of electric shock. FILTER: Glass Panel 8 6 5-11 8 0 To clean the motor fan should be undertaken by a qualified person, pay top attention to avoid any distortion of the fan during carrying out the clearance. 900 Disconnect the cooker hood from the power supply if this appliance will not be used for a long time. RCH-IA90SV-GX 8 6 5-11 8 0 32 0 39 0 436 465 Glove Dress the protective glove before you start to clean the hood. Remove the components gently during carrying out the clearance. 900 RCH-IA90SM-GX 12 1
IMPORTANT SAFETY INSTRUCTIONS: MAIN PARTS NAME Do not connect the air outlet to chimney flues or combustion gas ducts. Inner telescopic duct Outer telescopic duct Plastic pipe Electrical box PCB Do not leave naked flames under this hood Shutter Hook Blower box In case of any damage to power cable, replace the broken cable with a new one by qualified person. Blower assembly Synchronous motor Bottom cover LED lamp Switch PCB Oil cup Filter Do clean the hood correctly in accordance with instruction stated or it might cause the possibility of fire accident Motor Manual Blower Glass panel To replace the bulb should be undertaken by a qualified electrician or a competent person. Always use the bulb no more than 2W. 2 RCH-IA90SV-GX 2 11
Loose the screws on lamp panel, then take down the lamp panel. Inner telescopic duct Telescopic duct bracket Outer telescopic duct The temperature humidity sensor Filter Loose the screws on filter, then take down the filter. Plastic pipe Electrical box PCB Hook Shutter Blower box Blower assembly Blower Bottom cover Turn off the blower in clockwise direction. Motor Blower Oil cup Filter Switch PCB To replace negative-ion generator Glass panel Ve ionize LED lamp Glass Turn the negative-ion generator in anti clockwise direction, then take down it. RCH-IA90SM-GX 10 3
INSTALLATION REQUIREMENT 1. Do not install the cooker hood where there are many doors or windows in order to avoid to effecting the exhaust efficiency of the hood caused by air convection. (Fig. 1) PARTS REPLACEMENT Disconnect the power supply before operating. To replace switch 2. Install the cooker hood right above the hob. The recommended distance between the hob and the lower edge of the cooker hood is minimum 300mm and maximum 350mm. (Fig. 2) 3. In order to get the optimum performance, do not elongate the exhaust pipe too long, and try to make the bend of exhaust pipe less and biggest, ensure the connection is airproof. (Fig. 3) Step 1: Take down LED lamps, loose 4PCS screws from LED lamp holes by cross screwdriver. 4. After hanging the unit on the wall, ensure the hood is level and vertical. (Fig. 4) 5. The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must under no circumstances be connected to ventilation ducts for room in which fuel-burning appliances are installed. Fig.2 Fig.3 300~350mm Fig.1 s 2PCS for left side; 2PCS for right side Step 2: Push up and take down the glass panel, remove the oil cup. Loose 2pcs screw by cross screwdriver, then push up and take down the glass. Glass panel Glass Fig.4 LEVEL LEAN Step 3: After taking down the glass panel, loose 4 screws behind glass panel. Remove the switch cover board, loose 2 screws on the switch cover board. Then take down the switch. INSTALLATION PROCEDURES SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES;PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. To replace blower SS panel Loose the screws on SS panel bracket, then take down the SS panel. 4 9
MAINTENANCE CAUTION: NEVER PUT YOUR HAND INTO THE AREA HOUSING WHILE THE FAN IS OPERATING. FOR THE OPTIMAL LEVEL OF OPERATION, CLEAN THE COOKER HOOD SURFACE, FAN, AND ALUMINIUM FILTER REGULARLY. 1. Use only mild soap or detergent solutions to clean the cooker hood surface. Dry surfaces using soft cloth. 2. Using a stainless steel cleaner to bring the glow back into a stainless steel finish. 3. Clean the filter once a week or according to use status. Press the buckle of the filter slightly, take off the filter and put it into warm soapy water using mild detergent, wipe the filter with soft brush. Replace the filter after it is dry. 4. Clean the motor fan and other inside parts once half year or according to use by QUALIFIED PERSON. 5. DO NOT cleaning motor with water or other liquid. M4x16 Shutter Gasket for shutter Blower box Plastic pipe Step 1: Take down all M4x16 screws from shutter, put the shutter on gasket for shutter and overlap the screws holes of the shutter and gasket for shutter. Use all M4x16 screws to install the shutter and gasket for shutter to the hood. Step 2: Put the exhaust pipe to the shutter as picture showed. Rotate in direction of arrow. Make sure the exhaust pipe is fixed and can not be moved. TO REPLACE LIGHT BULB Shutter To replace led lamp Caution: LED lamp can not replace a new bulb, just can replace a new LED Lamp. Make sure all the control switches are off, and he cooker hood is unplugged! Please follow below instructions: Bracket Step 3: Matching the bracket to the holes of the inner duct cover and fix it well with M4 screws. 1.Take out the filters, and cut off the wire connection of the lamp. 2.Press the spring according to the arrow direction, then you can take off the lamp unit. M4 Inner duct cover Matching the bracket to the holes of the Outer duct cover and fix it well with M4 screws. 3.You can replace a new LED lamp unit no more then rating! 4. Then put the lamp unit to the hood in reverse direction. Connect the wire of the lamp. 5. Fit on the filters. Inner duct cover Step 4: Insert the inner duct cover into the outer duct cover. Outer duct cover 8 5
Inner duct cover Outer duct cover Expanding Tube Hook 5x60 Wood Expanding Tube 5x60 Wood 435 1 2 142 3 4 5x60 Wood 460 5 Expanding Tube Step 5: Matching the holes of outer duct cover and blower box, fix the outer duct cover to the blower box using 8pcs of M4 10 screws provided with the fixing tool. As the direction of illustrated. Step 6: Drill holes in the wall using a 8 mm drill bit. Use five screws to fit the hook on the wall in the screw holes like 1,2,3,4,5. Then put the hood to the hook make sure the hood is fixed and can not be moved! Step 7: 1. Draw the inner duct cover up to a suitable high, mark two keyhole of the outer duct cover bracket on the wall with pen. 2. Put down the inner duct cover gently, drill the keyholes in 75-85 mm depth on the horizontal level using 8mm drill. 3. Press the expanding tube provided into the holes. 4. Matching the inner duct cover with the holes, tighten the inner duct cover with two 5x60 wood screws provided. Step 8: Extend the air outlet of the exhaust pipe outof-door. Try to make the bend of the exhaust pipe more than 120. 6 OPERATION INSTRUCTION Touch this button, the hood enter into standby mode; Touch again, the hood is OFF. Touch this button when the hood is working, it will prolong working for 3mins. Touch it twice, the hood will turn off. Touch this button when the hood is in time delay state, the hood will turn off at once. Touch this button one time, the lamps will turn on; Touch it again, the lamps will turn off. Touch this button when the hood is in standby mode, the fan is changed from SOUP to STIR, the air suction is different according to your operation. Keep touching this button for 2 seconds, the motor is off, the hood is out of time delay state. Touch this button when the hood is in standby mode or the hood is working, the indicator of marked function from four functions( BOOST, AIR, PURIFY, ECO ) is flashing. Touch the button of the marked function; Touch the button of function. 7, the hood enters into again, the hood is out of the function: When the hood enters into this function, it will start working in lowest speed (12CBM/H) for 10mins every two hours once the hood is off. Touch the button of function. or there is a power failure, the hood is out of the function: When the hood enters into this function, negative ion generator in hood will produce negative ions. This function will keep on after touching the button of or there is a power failure. function: When the hood enters into this function, according to the current operating status, the hood will turn into BOOST function automatically once BOOST is needed. This function will keep on after touching the button of or there is a power failure. Touch this button to set after choosing the function ( BOOST, AIR, PURIFY, ECO required. Touch this button when the hood is working, the hood will go to the highest speed, with 18CBM/H air suction. Touch again or one minute later, the hood will come back to primary speed. Touch this button when the hood is in standby mode, the hood will go to the highest speed, with 18CBM/H air suction. Touch again or one minute later, the hood will come back to high speed, with 17CBM/H air suction.