Fixture Mount Night Light Controller SPECIFICATIONS Power.....................................120VAC, 60Hz Relay Type..................................Form C, N.O. Load Requirements @120VAC......................................500W.......................... isolated relay rated 5A 250VAC Low Voltage Connections RJ45 connection to FS sensor.. Control in, common, +24VDC 8-Pin connector to LED strip and battery 2-wire output to LEDs............. 400mA @10VDC max. 2-wire output to 9V Ni-MH battery....5-8ma @10VDC max. Line and Load Connections.............. 12-18AWG terminals Operating Temperature.............. 32 to 131 F (0 to 55 C) Dimensions............. 7.5 x 0.75 x 1.5 (190 x 19 x 38mm) Installation Instructions
DESCRIPTION The controller supplies power to FS series occupancy sensors, a light fixture ballast and an LED night light associated with the fixture. It also supplies a trickle charge for a 9Volt battery that provides backup power to the LED night light. The is designed for installation inside the lighting fixture housing. The has a male RJ45 plug attached to a 10 cable. Each FS series 24VDC occupancy sensor is equipped with a cable fitted with a male RJ45 plug. The two devices must be connected using the shielded male-to-male RJ45 connector provided with the. This cable carries power to the sensor and lighting control signals to the. Typically, the is connected to one FS sensor installed inside the lighting fixture, however, each controller can supply power for up to three FS series sensors. FS-CK accessory kits are required to connect multiple sensor wiring configurations. High voltage wiring should use at least 16 AWG wire. Check local building codes. OPERATION The must be used with a Legrand 740 31 momentary switch, provided with the. The switch toggles the fixture between full lighting operation, nightlighting using the LEDs, and no lighting at all. When the light fixture is ON, the FS sensor controls the light. When no motion is detected and the occupancy sensor s delay expires, the light goes OFF and the LED nightlight goes ON. Push the switch button twice to force OFF all lights. During a power failure lasting more than 2 seconds, the uses the 9V battery to power the LEDs. To conserve battery, the LEDs appear dimmer than during normal nightlight operation. The length of time the LEDs are lit during a power failure depends on battery status. To protect the battery, the turns off the LEDs when the battery discharges below a safe level. Low voltage connector to LED and Battery wire assembly provided by fixture manufacturer Shielded male-to-male RJ45 extension connector Low voltage RJ45 connection to FS sensor Line voltage input and Switch wiring 04799r1 120VAC Input HOT NEUTRAL GROUND 12-18AWG CU wire only C US LISTED Appliance Control 88T9 Model: Fixture Nightlight Controller 120VAC, 60Hz @120VAC 5A (N/O) Santa Clara, CA 800.879.8585 ISOLATED RELAY OUTPUTS TO LOAD COM LOAD 04800r1 Green LED Fig 1: connections and operation monitor LED Call 800.879.8585 or 972.578.1699 for Technical Support
INSTALLATION 1. Determine an appropriate mounting location inside the light fixture. 2. Use the holes or mounting slots at both ends of the to secure it to the fixture. 3. Install the LED nightlight strip and the 9Volt rechargeable Ni-MH battery (both provided by fixture manufacturer) in the fixture. 4. Install the FS sensor and make appropriate adjustments as described in the FS installation instructions. 5. Connect the RJ45 from the sensor to the RJ45 on the. 6. Connect the 8-pin low voltage connector from the to the battery and LED connector (supplied by fixture manufacturer). 7. Connect wires to load, switch and electrical supply as described in the wiring section. CAUTION MAKE SURE POWER IS OFF BEFORE INSTALLING THE SWITCH OR CONTROLLER. WIRING 12-16 AWG Low voltage connector to LED and Battery wire assembly provided by fixture manufacturer Cu Only Shielded male-to-male RJ45 extension connector Low voltage RJ45 connection to FS sensor Line voltage input and Switch wiring 04799r1 120VAC Input HOT NEUTRAL GROUND 12-18AWG CU wire only C US LISTED Appliance Control 88T9 Model: Fixture Nightlight Controller 120VAC, 60Hz @120VAC 5A (N/O) Santa Clara, CA 800.879.8585 ISOLATED RELAY OUTPUTS TO LOAD COM LOAD 04800r1 Green LED Fig 2: electrical supply, switch and lighting load wiring Visit our website for FAQs: www.wattstopper.com
Male-to-Male RJ45 Connector FS-205 Sensor 120VAC Input HOT NEUTRAL GROUND 04799r1 12-18AWG CU wire only C US LISTED Appliance Control 88T9 Model: Fixture Nightlight Controller 120VAC, 60Hz @120VAC 5A (N/O) Santa Clara, CA 800.879.8585 ISOLATED RELAY OUTPUTS TO LOAD COM LOAD 04800r1 To 9V Battery 8-Pin Connector To LED Strip Fig 3: RJ45 and 8-Pin connections Call 800.879.8585 or 972.578.1699 for Technical Support
TROUBLESHOOTING Lights will not turn on: Sensor LED does not flash: - Is green LED on? If yes, check RJ45 connections between sensor and. If no, check circuit breaker and wiring to wall switch and. - Check all wire connections. LED does flash: - Press the wall switch to toggle between OFF, nightlight, and full operation. - Check all wire connections and verify the load wire is tightly secured. Is the switch wired correctly? If lights still do not turn on, call 800.879.8585 for technical support. Lights will not turn off: The time delay on the FS sensor can be set from 30 seconds to 30 minutes. Ensure that the time delay is set to the desired delay and that there is no movement within the sensor s view for that time period. To quickly test the unit for proper operation, turn the time delay to minimum and move out of the sensor s view. Lights should turn off after 30 seconds. If lights still do not turn off, call 800.879.8585 for technical support. Call 800.879.8585 or 972.578.1699 for Technical Support
ORDERING INFORMATION Catalog # FS-105 FS-205 FS-305 FS-CK-1 Description Fixture night light package includes: one controller (120VAC, 60Hz), one male-to-male RJ45 connector, one Legrand 740 31 wall switch and cover plate (sensor sold separately) Ceiling tile mount, low voltage PIR occupancy sensor with adjustable time delay and light level Fixture mount, low voltage PIR occupancy sensor with adjustable time delay and light level Fixture or ceiling tile mount, low voltage PIR occupancy sensor, adjustable time delay Extension cables and splitter: two 10 cables with a shielded RJ45 male connector at each end, one shielded RJ45 splitter with female to dual female receptacles All sensors and are White. WARRANTY INFORMATION The Watt Stopper, Inc. warranties its products to be free of defects in materials and workmanship for a period of five (5) years. There are no obligations or liabilities on the part of The Watt Stopper, Inc. for consequential damages arising out of, or in connection with, the use or performance of this product or other indirect damages with respect to loss of property, revenue or profit, or cost of removal, installation or reinstallation. Putting a Stop to Energy Waste 2800 De La Cruz Boulevard, Santa Clara, CA 95050 Technical Support: 800.879.8585 972.578.1699 www.wattstopper.com 04798 r1 11/2004