Intrsion Alarm Systems B465 Universal Dal Path Commnicator B465 Universal Dal Path Commnicator www.boschsecrity.com The B465 Conettix Universal Dal Path Commnicator converts the Pblic Switch Telephone Network (PSTN) digital dialer, or dry contact otpts from an intrsion/ fire control panel to an IP signal for transmission over the Ethernet or celllar network. The B465 Conettix Universal Dal Path Commnicator is UL 864 10th Edition approved per NFPA 72 version 2013. The modle can se its bilt-in Ethernet connection, and/or an optional Conettix plg-in celllar modle (B440/B441/B442/B443) to send reports to the central station receiver. Atomation programming for the spported control panel remains nchanged with the installation of the B465 modle, ths simplifying the installation process This allows for a smooth transition from the PSTN realm into IP. All messages generated internally by the B465 are shown in Contact ID format at the central station. The modle can be powered from a 16.5 VAC transformer or 24 VDC power spply. Compatible with any control panel sing Contact ID, SIA, Plse 3/1 or Plse 4/2 commnication formats (ato detecting) No control panel reprogramming reqired to install Spports Ethernet directly and optional plg-in celllar commnication technologies in single, or mlti-path configrations Spports for configrable inpts and three configrable otpts Approved for Commercial Fire/Brglary applications as sole, primary, or secondary commnication path System overview The B465 simlates dial tone and line voltages when the digital dialer has a report to send. The modle simlates a PSTN connection to the central station. The modle decodes the control panel s PSTN dialer report and sends the decoded reports by IP connection sing Bosch s Conettix Protocol to the Conettix D6600, D6100IPv6, or D6100i Commnication Gateway/Receiver (referred to as the receiver). When the receiver acknowledges receipt of the message, it sends an acknowledgement report to the modle which in trn sends an acknowledgement to the connected control panel. This process maintains tre end-to-end secrity.
18 VAC BATTERY 18VAC + BAT - Y NO C NC RELAY 1 C NO RELAY 2 X MODULE 1 COMMUNICATION MODULE 1 SDI2 Device Bs R Y G B INPUTS 2.2 k End of Line Resistors 1 COM 2 3 COM 4 100BASE-T LINK USB SYSTEM TROUBLE PANEL LINE 1 PANEL LINE 2 C NO 12V 1 COM 2 3 COM 4 PNL LINE 1 PNL LINE 2 RELAY 3 AUX COM ETHERNET RX TX BATTERY AC MODULE RELEASE BAT TMPR EXTERNAL ANNUNC ETHERNET TRBL TX RX AC 2 B465 Universal Dal Path Commnicator 1 Callot ー Description 1 ー Intrsion/fire control panel 2 3 2 ー Control panel phone line connections 3 ー B465 Conettix Universal Dal Path Commnicator 4 ー B44x plg-in celllar commnicator 5 ー Ethernet connection (LAN/WAN) 6 ー Internet 7 ー Celllar commnication to celllar carrier 8 ー Celllar carrier network 9 ー Conettix receiver/gateway 10 ー Conettix receiver/gateway 11 ー Monitoring center atomation Fnctions 4 PSTN inpts (2) When the control panel s PSTN dialer sends a message, the modle simlates a PSTN connection to the central station. The modle connects to the host control panel throgh either one or both of the Phone Line inpts. Both Panel Line 1 and Panel Line 2 of the modle rn 28 VDC and spport Contact ID (4 and 10 digit accont codes), Plse 3/1, Plse 4/2, and SIA commnication formats. The B465 is setp to ato detect the commnication format which eliminates programming steps. IP Commnication options The modle ses the on-board Ethernet connector, and/or optional B440 Conettix Plg-in Commnicator, Celllar (3G), B441 Conettix Plg-in CDMA Celllar Commnicator, B442 Conettix Plg-in GPRS Celllar Commnicator, or B443 Conettix Plg-in HSPA+ Celllar Commnicator to commnicate with a Conettix D6600, Conettix D6100i or a Conettix D6100IPv6 Commnications Receiver/Gateway. Using Conettix IP commnication protocol offers a secre path that incldes anti-replay/anti-sbstittion featres and provides enhanced secrity with p to AES 256-bit encryption. 5 7 8 6 11 9 10 The modle spports Domain Name System (DNS) for central station commnication. DNS provides ease of se, eliminating the need to se static IP addresses as yor reporting destination, and accommodates a simple soltion for central station disaster recovery. Direct wire inpts The B465 provides for on-board inpts. Each inpt fnctions independently and does not interfere with the operation of the others. The modle monitors the inpt loops for normal, shorted, or open conditions between an inpt terminal and any of the inpt common terminals. Inpts are disabled by defalt so no EOL resistors are reqired ntil activated. These for inpts on the B465 connect to dry contact otpts on the control panel and generate Contact ID reports instead of sing a phone line connection/or in addition to sing the control panel phone connection. The available fnctions are: Panel System Troble Panel AC Fail Panel Battery Troble Fire Alarm Fire Troble Brg Alarm Brg Troble Fire Spervisory Each inpt allows the se of dry contacts or powered otpts p to 30 VDC if needed. The inpts se 2.2K EOLs to monitor the dry contact otpts when connected to dry contacts. The inpts recognize the following thresholds when sing dry contacts: 2.0 to 3.0 VDC = Normal, 3.7 to 5.0 VDC = Open, 0.0 to 1.3 VDC = Short. Otpts Incldes three programmable otpt relays rated at 30 VDC, 0.1 A. These otpts can be sed to show the stats of the B465 or they can be connected to the control panel zone inpts for reporting B465 system falts. The three otpts consist of RELAY 1, RELAY 2, and RELAY 3. RELAY 1 is active (energized) once the B465 is rnning. If the B465 detect a problem or loses power, RELAY 1 de-energizes, which can be sed to indicate a system troble on the local control panel's zone inpts, if reqired. Depending on the configration reqired to create a system troble on the control panel, the installer needs to se either the NO and COM or the NC and COM connections. Refer to the control panel manal for the reqired zone configration to obtain the proper inpt response. RELAY 2 is a normally open (NO) relay with contacts that close when the desired fnction programmed is detected. RELAY 3 is a normally open (NO) relay with contacts that close when the desired fnction programmed is detected.
3 B465 Universal Dal Path Commnicator Inpt power spply The B465 ses a 16.5 VAC transformer or 24 VDC voltage for its primary power sorce. The approved transformers are the D1640 plg-in transformer, D1640-CA plg-in transformer, or D1640-120WI transformer. The B465 can optionally be powered from 24 VDC power sorce applied to the AC terminals. B465 modlar connections The B465 modle has three modlar connections. Celllar plg-in connector. Connects to a celllar commnication modle. Tamper connector. Connects the ICP-EZTS Dal Tamper Switch for monitoring the enclosre cover. External Annnciator connector. Connects to the optional B46 modle. On-board LED Indicators The B465 has a total of ten on-board LEDs that indicate the modle's stats (SYSTEM TROUBLE, TX, RX, POWER, BATTERY, HEARTBEAT, Panel Line 1 (ACT),Panel Line 2 ( ACT), 100BASE-T and ETHERNET LINK). B46 External Annnciator (Optional) The B46 is an optional modle that provides external modle LED and sonder stats when installed in a spported enclosre. The modle has 3 LEDs (System Troble, Power, and Battery) which illminate throgh the B46 LED cover. The LED cover snaps into a knockot in the enclosre door. The B46 is compatible with the B10, B10R, B11, B11R, and D8103 enclosres. Certifications and approvals Region USA UL 365 - Police Station Connected Brglar Alarm Units and Systems UL 609 - Local Brglar Alarm Units and Systems UL 636 - Holdp Alarm Units and Systems UL 864 - Control Units and Accessories for Fire Alarm Systems (Commercial Fire) UL 985 - Hosehold Fire Warning System Units UL 1023 - Hosehold Brglar Alarm System Units UL 1076 - Proprietary Brglar Alarm Units and Systems Region ICES-003 - Information Technology Eqipment (ITE) ULC-ORD C1023 - Hosehold Brglar Alarm System Units ULC-ORD C1076 - Proprietary Brglar Alarm Units and System Certification USA UL 20150807-S1871 Parts inclded Qantity CSFM 7300-1615:0253 FDNY- CoA 6214 Component 1 B465 Conettix Universal Dal Path Commnicator 1 Hardware pack 1 Qick Start Gide (hardcopy) 1 Wiring label (hardcopy) 1 Literatre (mini-cd) Technical specifications Properties Dimensions Environmental considerations Relative hmidity Temperatre (operating) Operational se Power reqirements Standby battery crrent 4.40 in x 6.90 in x 1.50 in (111 mm x 175 mm x 38 mm) 5% to 93% at +32 C (+90 F) 0 C to +49 C (+32 F to +120 F) Indoor se only Battery inpt: B465: Idle 150 ma; Alarm 230 ma 24 VDC inpt crrent 24 VDC inpt: B465: Idle 120 ma; Alarm 160 ma Wiring Canada UL 1610 - Central Station Brglar Alarm Units NIST FIPS 197 AES Certification (IP Commnications) CSFM approved FCC Part 15 Class B CAN/ULC S303 - Local Brglar Alarm Units and Systems CAN/ULC S304 - Signal Receiving Centre and Premise CAN/ULC S545 - Residential Fire Warning System Control Terminal wire size 12 AWG to 22 AWG (2.0 mm to 0.65 mm) Transformer secondary wiring length Control panel phone line wiring 15 m (50 ft) maximm nshielded wire 100 Ω loop resistance, maximm nshielded wire
4 B465 Universal Dal Path Commnicator Inpt loop wiring 100 Ω loop resistance, maximm nshielded wire Ethernet wiring 100 m (328 ft) maximm sing Cat 5 wire or better Compatibility Compatible PSTN inpt formats Receivers Celllar Modles Enclosres Transformers Ordering information Ademco Contact ID (SIA DC-05) +10 digit accont codes Plse 3/1, 3/1 Checksm (2300 Hz ACK Tone) Plse 3/1, 3/1 Checksm (1400 Hz ACK Tone) Plse 4/2 (2300 Hz ACK Tone) Plse 4/2 (1400 Hz ACK Tone) SIA (SIA8, SIA20) 110 and 300 bad D6600 D6100i D6100IPv6 B440 Conettix Plg-in Commnicator, Celllar (3G) B441 Conettix Plg-in CDMA Celllar Commnicator B442 Conettix Plg-in GPRS Celllar Commnicator B443 Conettix Plg-in HSPA+ Celllar Commnicator B46 External Annnciator B10 Medim Control Panel Enclosre B10R Medim Control Panel Enclosre (Red) B11 Small Control Panel Enclosre B11R Small Control Panel Enclosre (Red) D8103 Universal Enclosre D8108A Attack Resistant Enclosre D1640 transformer 120 VAC inpt, 16.5 VAC, 40 VA otpt plg-in D1640-CA transformer 120 VAC inpt, 16.5 VAC, 40 VA otpt plg-in D1640-120WI transformer 120 VAC inpt, 16.5 VAC, 40 VA otpt wired in B465 Universal Dal Path Commnicator Compatible with control panels sing a standard digital dialer format. Provides end-to-end secrity. Allows digital dialer control panels to work over an IP network (sch as LAN, WAN, or the Internet). Order nmber B465 Accessories B46 External Annnciator An optional modle that ses adio and LEDs to show System Troble, Power, and Battery stats throgh a knockot on select enclosre doors Order nmber B46 B10 Medim Control Panel Enclosre White, steel enclosre. Accepts an optional lock and tamper switch. Measres 35.6 cm x 31.8 cm x 7.6 cm (14 in x 12.5 in x 3 in). Order nmber B10 B10R Medim Control Panel Enclosre (Red) Red, steel enclosre. Accepts an optional lock and tamper switch. Order nmber B10R B11 Small Control Panel Enclosre White, steel enclosre. Accepts an optional lock and tamper switch. Measres 27.8 cm x 25.9 cm x 8.32 cm (10.9 in x 10.2 in x 3.3 in). Order nmber B11 B11R Small Control Panel Enclosre (Red) Red, steel enclosre. Accepts an optional lock and tamper switch. Measres 27.8 cm x 25.9 cm x 8.32 cm (10.9 in x 10.2 in x 3.3 in). Order nmber B11R D8103 Enclosre Grey steel enclosre measring 41 cm x 41 cm x 9 cm (16 in. x 16 in. x 3.5 in.). Order nmber D8103 D8108A Attack Resistant Enclosre Grey steel enclosre measring 41 cm x 41 cm x 9 cm (16 in. x 16 in. x 3.5 in.). UL Listed. Incldes lock and key set. B520, B4512, and B5512 reqire the B12 monting plate. Order nmber D8108A B12 Monting Plate for D8103 Enclosre Reqired for monting select control panels and other devices in D8103, D8108A, D8109, or BATB Battery Box enclosres. Order nmber B12 D101 Lock and Key Set Short-body lock set with one key spplied. Uses the D102 (#1358) replacement key. Order nmber D101 ICP EZTS Dal Tamper Switch Combination tamper switch with a wire loop for additional tamper otpts. Order nmber ICP-EZTS D1640 Transformer System transformer rated at 16.5 VAC, 40 VA. Order nmber D1640 D1640-CA Transformer For se in Canada. System transformer rated at 16.5 VAC, 40 VA. Order nmber D1640-CA
5 B465 Universal Dal Path Commnicator B440 Conettix Plg-in Celllar Commnicator Dal technology 3G EVDO/CDMA celllar commnicator for secre two-way IP commnication on the Verizon Wireless network. Order nmber B440 B441 Conettix Plg-in Celllar Commnicator Mlti-fnction CDMA celllar commnicator for secre two-way IP commnication on the Verizon Wireless network. Order nmber B441 B442 Conettix Plg-in GPRS Celllar Commnicator Mlti-fnction celllar commnicator that provides IP commnication over a (GPRS) celllar network. Order nmber B442 B443 Conettix Plg-in HSPA+ Celllar Commnicator Mlti-fnction 3G/4G celllar commnicator providing IP commnication over a GPRS/EDGE/UMTS/HSPA+ celllar network. Order nmber B443 Represented by: Erope, Middle East, Africa: Germany: North America: Asia-Pacific: Bosch Secrity Systems B.V. P.O. Box 80002 5600 JB Eindhoven, The Netherlands Phone: + 31 40 2577 284 emea.secritysystems@bosch.com emea.boschsecrity.com Bosch Sicherheitssysteme GmbH Robert-Bosch-Ring 5 85630 Grasbrnn Germany www.boschsecrity.com Bosch Secrity Systems, Inc. 130 Perinton Parkway Fairport, New York, 14450, USA Phone: +1 800 289 0096 Fax: +1 585 223 9180 onlinehelp@s.bosch.com www.boschsecrity.s Robert Bosch (SEA) Pte Ltd, Secrity Systems 11 Bishan Street 21 Singapore 573943 Phone: +65 6571 2808 Fax: +65 6571 2699 apr.secritysystems@bosch.com www.boschsecrity.asia Bosch Secrity Systems 2016 Data sbject to change withot notice 18116851979 en, V13, 01. Ag 2016