Fire Safety Installation Instructions Model ADBX11 Audible Base INTRODUCTION Model ADBX11 The SIEMENS Model ADBX11 Audible Base consists of a standard Series 11 base combined with an audible device. All field wiring terminates at two fourposition terminal blocks located on the back of the unit. The ADBX11 is used with FP11 and FPT11 detectors, P/N 315095921, and FSDP, FSDPT, and FSDT detectors, P/N 315699481. The ADBX11 operates as described below (Refer to Figures 1, 2, 3, 4, and 5). The ADBX11 can generate either steady or temporal tone with the insertion of a jumper at the terminal block. Refer to Tone Selection on page 11. APPLICATION NOTE The ADBX11 is a UL268 listed smoke detector supplementary device which combines detector base and audible device functions. It meets or exceeds the 85 db at 10 foot audibility requirement for smoke alarms as specified in UL217, Single and Multiple Station Smoke Alarms and NFPA 72 for sleeping areas. When used in conjunction with listed, compatible Siemens equipment, the ADBX11 may be used in lieu of single/multiple station smoke alarms to achieve enhanced, systemlevel functionality. Typical applications are sleeping rooms in hotels, guest suites, dormitories, daycare, and residential board and care facilities as designated in NFPA 72. ELECTRICAL RATINGS AND CONSTRAINTS Model ADBX11 Voltage Rating: 1731 VDC Current: Supervisory 0A Alarm 24mA at 25 VDC Constraints: 1. The maximum number of ADBX11s per an MMB1/2, SMB1/2, or CSM4 notification appliance circuit is 60, with no other devices connected, and with the maximum loop current available. Note: The number of ADBX11s cannot exceed the maximum current available to the loop. See the MXL Manual, P/N 315092036, or the MXLIQ Manual, P/N 315093624, for the compatibility details of ALD and notification appliance circuit wiring. Siemens Building Technologies, Inc. 8 Fernwood Road Florham Park, New Jersey 07932 Siemens Building Technologies, Ltd. 2 Kenview Boulevard Brampton, Ontario L6T 5E4 CN P/N 3150962287
* 3.6K, 1/4W RESISTOR, MODEL EL31. ** POLARITY SHOWN IN NORMAL SUPERVISORY STATE AT TERMINALS 1 AND 2 OF ADBX11. PROPER POLARITY MUST BE MAINTAINED OR AUDIBLE BASE WILL NOT OPERATE PROPERLY. EACH AUDIBLE BASE MUST BE TESTED TO VERIFY OPERATION. USE A MODEL MPX2 MOUNTING PLATE TO MOUNT A TRI2R, TRIB6 OR TRI60R IN A SYSTEM 3 ENCLOSURE. TONE SELECTION (SEE PAGE 11). USE A MODEL MPI2 MOUNTING PLATE TO MOUNT A TRIR OR FSTRIR IN A SYSTEM 3 ENCLOSURE. FOR MORE DETAILED WIRING INFORMATION, REFER TO THE FOLLOWING INSTALLATION INSTRUCTIONS, AS APPLICABLE; TRI2R, P/N 315090556; TRIB6R, P/N 315093315; TRI60R, P/N 315092329; TRIR, P/N 315096242; OR FSTRIR, P/N 315699484. 2 Figure 1 Installation/Wiring Diagram for ADBX11 Powered by Auxiliary Power Supply with Battery Backup
3
* 3.6K, 1/4W RESISTOR, MODEL EL31. ** POLARITY SHOWN IN NORMAL SUPERVISORY STATE AT TERMINALS 1 AND 2 OF ADBX11. PROPER POLARITY MUST BE MAINTAINED OR AUDIBLE BASE WILL NOT OPERATE PROPERLY. EACH AUDIBLE BASE MUST BE TESTED TO VERIFY OPERATION. TONE SELECTION (SEE PAGE 11). 4 Figure 2 Installation/Wiring Diagram for ADBX11 Audibles Powered by Auxiliary Power Supply (No Battery Backup)
NOTE: FOR MOUNTING A TRI RELAY MODULE IN A SYSTEM 3 ENCLOSURE: USE A MODEL MPX2 MOUNTING PLATE TO MOUNT A TRI2R, TRIB6R, OR TRI60R, OR USE A MODEL MPI2 MOUNTING PLATE TO MOUNT A TRIR OR FSTRIR. FOR MORE DETAILED WIRING INFORMATION, REFER TO THE FOLLOWING INSTALLATION INSTRUCTIONS, AS APPLICABLE: TRI2R, P/N 315090556; TRIB6R, P/N 315 093315; TRI60R, P/N 315092329; TRIR, P/N 315096242, OR FSTRIR, P/N 315699484. 5
6 Figure 3 Installation/Wiring Diagram for ADBX11 Audibles Powered by System MXL/MXLIQ Main Board
TO NEXT ADBX11, DB11, DB3S, OR DBX3RS 1b 6 1a 5 FROM ALD LOOP OF SYSTEM MXL/MXLIQ CONTROL PANEL ADBX11 AUDIBLE SIGNAL CIRCUIT SHOWN STYLE Y (CLASS B) MAY BE STYLE Z (CLASS A) 8 7 6 5 1 2 3 4 8 7 6 5 1 2 3 4 TONE SELECTION (SEE PAGE 11) * * EOL DEVICE 2.2K, 1/2W P/N 140820380 * ** NAC CIRCUITS POLARITY SHOWN IN SUPERVISORY STATE. PROPER POLARITY MUST BE MAINTAINED OR AUDIBLE BASE WILL NOT OPERATE PROPERLY. ** Make this connection to any of the following Refer to the following Installation Instructions as needed: C SM4 P/N 31509085 4 EACH AUDIBLE BASE MUST BE TESTED TO VERIFY OPERATION. terminations: MAX CURREN T C SM4 2 1 0 3 1 1 1 5 AMP S I CP P/N 31509247 1 I CP/B6 T B1 (3 ) TB1 (6 ) 1 5 AMP S I CPB6 P/N 31509530 6 AMPS 1 5 10 8, 16 6, 4, Z C18B P/N 31509091 0 14, 2, 12, Z C18B 1, 3, 5, 7, 9, 11, 13, 15 Z C24AB P/N 31509126 2 AMPS 1 5 8; 15, 7, 4; 16 12; 3, 11, 14,, Z C24AB 1, 2; 5, 6 ; 9, 10; 13, P AD2 P/N 31509427 5 P AD2 T B2 (4, 6, 8, 10 ) TB2 (3, 5, 7, 9 ) 3 0 AMP S Figure 4 Installation/Wiring Diagram for ADBX11 Audibles Powered by System MXL/MXLIQ Modules 7
ANALOG LOOP CONNECTION SUPERVISED ** STYLE Y SUPERVISED STROBE ACTIVATION SUPV: 9VDC,.5mA ACTIVATED: 24VDC, 1.5A MAX POLARITY SHOWN IN SUPV. CONDITION TB1 1 2 3 4 ICPB6 5 6 JP2 POWER LIMITED * PROGRAM PLUG JP1 DC INPUT RATED 24 27.3 VDC FWR SUPV: 12mA ACTIVATED: 1.5A MAX TB2 6 5 4 3 2 1 * 1 8 2 7 3 6 4 5 ADBX11 1 2 8 7 3 6 4 5 ADBX11 EARTH SHIELD 15K, 1/2W, 5% EOL RESISTOR P/N 140820400 5 6 1a 1b MODULE INPUT SUPPLY FROM PS35, PSR1,OR UL LISTED POWER SUPPLY TO NEXT ADBX11, DB11,DB3S, OR DBX3RS ELECTRICAL: INPUT DC SUPPLY: SUPERVISORY OUTPUT: ACTIVATED: 2427.3 VDC, 18mA MAX 9 VDC, 0.5mA 24 VDC, 1.5A, POWER LIMITED Figure 5 Using ICPB6 to Supervise Power to ADBX11 8
** STYLE Z 15K, 1/2W, 5% EOL RESISTOR P/N 140820400 TB1 1 2 3 4 5 6 ICPB6 PROGRAM PLUG JP2 JP1 * 1 8 2 7 3 6 4 5 ADBX11 1 8 2 7 TB2 6 5 4 3 2 1 * 3 6 4 5 ADBX11 EARTH SHIELD * ** TONE SELECTION (SEE PAGE 11) NAC CIRCUITS POLARITY SHOWN IN SUPERVISORY STATE. PROPER POLARITY MUST BE MAINTAINED OR AUDIBLE BASE WILL NOT OPERATE PROPERLY. 5 6 1a 1b TO NEXT ADBX11, DB11,DB3S, OR DBX3RS NOTE: All wiring must comply with national and local codes. 9
Figure 6 Installation/Wiring Diagram for ADBX11 Audbiles Powered by System FS100 Main Board 2. Maximum line resistance permitted (both wires), not including the end of line resistor, is 3 ohms. A minimum of 14 AWG wire must be used. 3. Ttapping of the notification appliance circuit (Figures 1, 2, 3, 4, and 5) is not allowed. 4. If the ADBX11 is powered by System MXL/MXLIQ (Figures 3, 4, and 5) or FS100 (Figure 6), the notification appliance circuits supply 1.5A. If more than 1.5A is required, use the configuration in Figure 1 or Figure 2 for auxiliary power. See Note on page 1. 5. Connect terminal 6 of the PS35 (Figures 1 and 2) to the minus DC side of the MXL/MXLIQ main power supply for proper ground fault supervision. Note: For additional information on the modules used in an individual system, refer to the Installation Instructions for that particular module or contact your authorized Siemens Building Technologies, Inc. representative. DETECTOR PLACEMENT The FP11, FPT11, FSDP, FSDT and FSDPT detectors can be used with the ADBX11 Detector Base. Refer to the FP11/FPT11 Installation Instructions, P/N 315095921, or the FSDP/FSDT/FSDPT Installation Instructions, P/N 315699481, as applicable for further information. 10
Even though no specific spacings are allocated to the detectors used with this base, use 30 foot center spacing (900 sq ft), as referred to in NFPA Standard 72 National Fire Alarm Code, Chapter 5 and CAN/ULCS524, as a guide or starting point, if practical, in a detector installation layout. This spacing is based on ideal conditions smooth ceiling, no air movement, and no physical obstructions. In all installations (except in special circumstances like computer room underfloors), locate the detector on the ceiling, a minimum of 6 inches from a side wall, or on a wall, between 4 and 6 inches from the ceiling. If questions arise regarding detector placement, it is extremely important that the drawings provided or approved by Siemens Building Technologies, Inc. or by its authorized distributors be followed! The detector placements shown on these drawings were chosen after a careful evaluation of all facets of protecting the area. Environmental factors such as air current, temperature, humidity, air pressure, and the nature of the fire load are carefully considered. Special consideration is given to room or area configuration and the type of ceiling (sloped or flat, smooth or beamed). Siemens Building Technologies, Inc.'s extensive experience in the design of fire detection systems assures optimum detector placement and is reflected in these drawings. Follow sound engineering judgment made by qualified personnel. DETECTOR WIRING (USING THE ADBX11 BASE) (Refer to Figure 6.) Audible base model ADBX11 should be interconnected as shown in the Installation/Wiring Diagrams above and wired to the specific system modules and control panels following the appropriate instructions. For operation with System MXL/MXLIQ, note any limitations on the number of audible bases permitted on each MMB1/2, SMB1/2, or CSM4 audible circuit, depending on the total cable resistance for each audible signal circuit. (See ELECTRICAL RATINGS section.) TONE SELECTION With audible base Model ADBX11, the user can choose either temporal tone or steady tone. (Refer to Figure 7.) For Temporal Tone: Terminals 3 and 4 are shorted (insert a jumper). For Steady Tone: Terminals 3 and 4 are not connected (without a jumper). DETECTOR MOUNTING (USING THE ADBX11 BASE) The detector base comes from the factory prewired. All signaling and initiating circuits are connected directly to the back of the ADBX11 audible base using the fourposition terminal blocks. Note: The Audible Base Model ADBX11 attaches only to a 4inch square electrical box with extension. 11
Figure 7 ADBX11 Audbile Base Terminal Blocks Mounting the Detector Base 1. Route all wires out from the outlet box. 2. When the alarm LED viewing is critical, position the LED mark on the base in the intended direction (Refer to Figure 8). 3. Make connections directly to the audible base terminals located on the back of the base. Refer to the related lnstallation/wiring Diagram. 4. After all bases are installed, check loop continuity. For ADBX11 loop continuity check, refer to the System MXL or MXLIQ Manual Checkout Procedure. 5. If loop continuity is acceptable, proceed with detector head installation. ALARM LED LOCATION WITH DETECTOR INSTALLED IN BASE DO NOT PAINT Figure 8 Positioning the Alarm LED BASE MOUNTING HOLES Siemens Building Technologies, Inc. 8 Fernwood Road Florham Park, New Jersey 07932 Siemens Building Technologies, Ltd. 2 Kenview Boulevard Brampton, Ontario L6T 5E4 CN P/N 3150962287