age 1 of 114 Report o.: STUESO017022702211HS TEST REORT Safety of household and similar electrical appliances art 2 : articular requirements for fans Report umber.... : STUESO017022702211HS Date of issue... : Feb. 27, 2017 Total number of pages... 114 Applicant s name... : Address... : Cantaş iç ve Dış Ticaret Soğutma Sistemleri Sanayi A.Ş. Kore Şehitleri Caddesi o:53, Zincirlikuyu 34394 Şişli / İSTABUL- Turkey Test specification: Standard... : Test procedure... : on-standard test method..: Test Report Form o.... : Test Report Form(s) Originator... : :2002 (Second edition) + A1:2004 +A2:2008 in conj. With IEC 60335-1:2010 (Fifth Edition) Test report ot applicable IEC60335_2_80E DEKRA Certification B.V. Master TRF... : Dated 2012-09 Test item description... : Trade Mark... : Manufacturer... : Model/Type reference... : Air curtain Aircraft GZ THEODOOR TECH CO., LTD o.1-63 hoenix 3 Heng Road, Sino-Singapore KnowIedge City, Luogang District, Guangzhou, China FM-1206T/Y, FM-1209T/Y, FM-1210T/Y, FM-1212T/Y, FM- 1215T/Y, FM-1218T/Y, FM-1220T/Y Ratings... : 220-240V~, 50Hz, Class I, FM-1206T/Y(140W), FM-1209T/Y (160W), FM-1210T/Y(180W), FM-1212T/Y(200W), FM-1215T/Y(230W), FM-1218T/Y(300W), FM-1220T/Y(350W) TRF o. IEC60335_2_80E
age 3 of 114 Report o.: STUESO017022702211HS Summary of testing: Attachment 1: European Group Differences and ational Differences for E 60335-1, E 60335-2-80 and E 62233 according to. Attachment 2: hotos. Tests performed (name of test and test clause): Test according to the following standards were carried out: : 2002 + A1: 2004 + A2: 2008 IEC 60335-1: 2010 E 60335-2-80: 2003 + A1: 2004 + A2: 2009 E 60335-1: 2012 + A11: 2014 E 62233: 2008 Testing location: Standard Technology Union Co., Ltd. o.202, Building A, Jingye Sanjie, Yushu Industrial ark, Guangzhou Economic & Technology Development Zone, Guangzhou, Guangdong, China Model FM-1209T/Y and FM-1220T/Y were subjected to full tests as representative model. Model FM-1220T/Y using 12µf capacitor was subjected for clause 10, 11, 19 and construction checked. Other model was subjected for construction checked. Summary of compliance with ational Differences: European group differences and national differences were taken into account TRF o. IEC60335_2_80E
age 4 of 114 Report o.: STUESO017022702211HS Copy of marking plate The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective CBs that own these marks. otes: 1. As declared by the applicant, the importer (and manufacturer, if it is different) s name, registered trade name or registered trade mark and the postal address will be marked on the products before being place on the market. The contact details shall be in a language easily understood by end-users and market surveillance authorities. 2. Marking on the packaging or in a document accompanying the electrical equipment is only acceptable if It is not possible to place such markings on the product. TRF o. IEC60335_2_80E
age 5 of 114 Report o.: STUESO017022702211HS Test item particulars... : Classification of installation and use... : Supply Connection... : Air curtain Fixed appliance Supply cord fitted without plug, type Y attachment... : ossible test case verdicts: - test case does not apply to the test object...: (ot applicable) - test object does meet the requirement...: (ass) - test object does not meet the requirement...: F (Fail) Testing...: Date of receipt of test item...: Feb. 21, 2017 Date (s) of performance of tests...: Feb. 21, 2017 to Feb. 27, 2017 General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. "(see Enclosure #)" refers to additional information appended to the report. "(see appended table)" refers to a table appended to the report. Throughout this report a comma / point is used as the decimal separator. Manufacturer s Declaration per sub-clause 4.2.5 of IECEE 02: The application for obtaining a Test Certificate includes more than one factory location and a declaration from the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided... : Yes ot applicable When differences exist; they shall be identified in the General product information section. ame and address of factory (ies)... : GZ THEODOOR TECH CO., LTD o.1-63 hoenix 3 Heng Road, Sino-Singapore KnowIedge City, Luogang District, Guangzhou, China General product information: The appliance is fixed appliance for household and indoor used. All the models are identical except the model number, appearance, size and input power. TRF o. IEC60335_2_80E
age 6 of 114 Report o.: STUESO017022702211HS 5 GEERAL CODITIOS FOR THE TESTS Tests performed according to clause 5, e.g. nature of supply, sequence of testing, etc. 5.7 Fans to be used in tropical climates, the tests of clause 10,11 and 13 are carried out at 40 C +/- 2 C (IEC 60335-2-8) Fans marked with ambient operating temperature, the tests of clause 10, 11 and 13 are carried out at marked value +/- 2 C (/A1) 6 CLASSIFICATIO 6.1 rotection against electric shock: Class 0, 0I, I, II, III......: Class I 6.2 rotection against harmful ingress of water At least IX2 for Duct fans (IEC 60335-2-8) 6.101 Classification to climatic conditions : temperature climates, tropical climates (IEC 60335-2-8) Temperature climates 7 MARKIG AD ISTRUCTIOS 7.1 Rated voltage or voltage range (V)......: 220-240V Symbol for nature of supply, or......: ~ Rated frequency (Hz)......: 50Hz Rated power input (W), or......: Rated current (A)......: Manufacturer's or responsible vendor's name, trademark or identification mark......: Model or type reference......: Symbol IEC 60417-5172, for class II appliances FM-1206T/Y(140W) FM-1209T/Y(160W), FM-1210T/Y(180W), FM-1212T/Y(200W), FM-1215T/Y(230W), FM-1218T/Y(300W), FM-1220T/Y(350W) FM-1206T/Y, FM-1209T/Y, FM-1210T/Y, FM-1212T/Y, FM-1215T/Y, FM-1218T/Y, FM-1220T/Y I number, other than IX0......: IX0 TRF o. IEC60335_2_80E
age 7 of 114 Report o.: STUESO017022702211HS Symbol IEC 60417-5180, for class III appliances, unless the appliance is operated by batteries only Symbol IEC 60417-5036, for the enclosure of electrically-operated water valves in external hosesets for connection of an appliance to the water mains, if the working voltage exceeds extra-low voltage For tropical climates marked with letter T (IEC 60335-2-8) Fans intended for operation in location where the local temperature exceeds 40 C shall be marked with the ambient operating temperature. (IEC 60335-2-80/A1) 7.2 Warning for stationary appliances for multiple supply Warning placed in vicinity of terminal cover 7.3 Range of rated values marked with the lower and upper limits separated by a hyphen Different rated values marked with the values separated by an oblique stroke 7.4 Appliances adjustable for different rated voltages, the voltage setting is clearly discernible Requirement met if frequent changes are not required and the rated voltage to which the appliance is to be adjusted is determined from a wiring diagram 7.5 Appliances with more than one rated voltage or one or more rated voltage ranges, marked with rated input or rated current for each rated voltage or range, unless the power input is related to the arithmetic mean value of the rated voltage range Relation between marking for upper and lower limits of rated power input or rated current and voltage is clear 7.6 Correct symbols used Symbol for nature of supply placed next to rated voltage Symbol for class II appliances placed unlikely to be confused with other marking TRF o. IEC60335_2_80E
age 8 of 114 Report o.: STUESO017022702211HS Units of physical quantities and their symbols according to international standardized system 7.7 Connection diagram fixed to appliances to be connected to more than two supply conductors and appliances for multiple supply, unless correct mode of connection is obvious 7.8 Except for type Z attachment, terminals for connection to the supply mains indicated as follows: - marking of terminals exclusively for the neutral conductor (letter ) - marking of protective earthing terminals (symbol IEC 60417-5019) - marking not placed on removable parts 7.9 Marking or placing of switches which may cause a hazard 7.10 Indications of switches on stationary appliances and controls on all appliances by use of figures, letters or other visual means......: This applies also to switches which are part of a control If figures are used, the off position indicated by the figure 0 The figure 0 indicates only OFF position, unless no confusion with the OFF position letters Figure 0 is not used 7.11 Indication for direction of adjustment of controls 7.12 Instructions for safe use provided Details concerning precautions during user maintenance The instructions state that: - the appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction - children being supervised not to play with the appliance For a part of class III construction supplied from a detachable power supply unit, the instructions state that the appliance is only to be used with the unit provided TRF o. IEC60335_2_80E
age 9 of 114 Report o.: STUESO017022702211HS Instructions for class III appliances state that it must only be supplied at SELV, unless it is a battery-operated appliance, the battery being charged outside the appliance For the guards have to be removed purpose for cleaning should: (IEC 60335-2- 80/A1) Ensure that the fan is switched off from the supply mains before removing the guard. 7.12.1 Sufficient details for installation supplied For an appliance intended to be permanently connected to the water mains and not connected by a hose-set, this is stated The installation instructions include the substance of the following: (IEC 60335-2- 80) - the model or type reference of a luminaire - mounting location for partition fans - The installation height for fans intended to be mounted at high level - that precautions for duct and partition fans. 7.12.2 Stationary appliances not fitted with means for disconnection from the supply mains having a contact separation in all poles that provide full disconnection under overvoltage category III, the instructions state that means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules 7.12.3 Insulation of the fixed wiring in contact with parts exceeding 50 K during clause 11; instructions state that the fixed wiring must be protected 7.12.4 Instructions for built-in appliances: - dimensions of space - dimensions and position of supporting and fixing - minimum distances between parts and surrounding structure - minimum dimensions of ventilating openings and arrangement - connection to supply mains and interconnection of separate components TRF o. IEC60335_2_80E
age 10 of 114 Report o.: STUESO017022702211HS - allow disconnection of the appliance after installation, by accessible plug or a switch in the fixed wiring, unless a switch complying with 24.3 7.12.5 Replacement cord instructions, type X attachment with a specially prepared cord Replacement cord instructions, type Y attachment Replacement cord instructions, type Z attachment 7.12.6 Caution in the instructions for appliances incorporating a non-self-resetting thermal cut-out that is reset by disconnection of the supply mains, if this cut-out is required to comply with the standard 7.12.7 Instructions for fixed appliances stating how the appliance is to be fixed 7.12.8 Instructions for appliances connected to the water mains: - max. inlet water pressure (a)......: - min. inlet water pressure, if necessary (a)...: Instructions concerning new and old hose-sets for appliances connected to the water mains by detachable hose-sets 7.13 Instructions and other texts in an official language English version checked 7.14 Marking clearly legible and durable, rubbing test as specified 7.15 Markings on a main part Marking clearly discernible from the outside, if necessary after removal of a cover For portable appliances, cover can be removed or opened without a tool For stationary appliances, name, trademark or identification mark and model or type reference visible after installation For fixed appliances, name, trademark or identification mark and model or type reference visible after installation according to the instructions Indications for switches and controls placed on or near the components. Marking not on parts which can be positioned or repositioned in such a way that the marking is misleading TRF o. IEC60335_2_80E
age 11 of 114 Report o.: STUESO017022702211HS 7.16 Marking of a possible replaceable thermal link or fuse link clearly visible with regard to replacing the link 8 ROTECTIO AGAIST ACCESS TO LIVE ARTS 8.1 Adequate protection against accidental contact with live parts 8.1.1 Requirement applies for all positions, detachable parts removed Lamps behind a detachable cover not removed, if conditions met Insertion or removal of lamps, protection against contact with live parts of the lamp cap Use of test probe B of IEC 61032, with a force not exceeding 1 : no contact with live parts Lamps are not removed. However, during insertion or removal of lamps, no contact with live parts of the lamp cap. () 8.1.2 Use of test probe 13 of IEC 61032, with a force not exceeding 1, through openings in class 0 appliances and class II appliances/constructions: no contact with live parts Test probe 13 also applied through openings in earthed metal enclosures having a non-conductive coating: no contact with live parts 8.1.3 For appliances other than class II, use of test probe 41 of IEC 61032, with a force not exceeding 1 : no contact with live parts of visible glowing heating elements 8.1.4 Accessible part not considered live if: - safety extra-low a.c. voltage: peak value not exceeding 42.4 V - safety extra-low d.c. voltage: not exceeding 42.4 V - or separated from live parts by protective impedance If protective impedance: d.c. current not exceeding 2 ma, and a.c. peak value not exceeding 0.7 ma - for peak values over 42.4 V up to and including 450 V, capacitance not exceeding 0,1 F TRF o. IEC60335_2_80E
age 12 of 114 Report o.: STUESO017022702211HS - for peak values over 450 V up to and including 15 kv, discharge not exceeding 45 C - for peak values over 15kV, the energy in the discharge not exceeding 350 mj 8.1.5 Live parts protected at least by basic insulation before installation or assembly: - built-in appliances - fixed appliances - appliances delivered in separate units 8.2 Class II appliances and constructions constructed so that there is adequate protection against accidental contact with basic insulation and metal parts separated from live parts by basic insulation only Only possible to touch parts separated from live parts by double or reinforced insulation Remove the detachable parts for user maintenance purpose, the basic insulation of internal wiring may be touched provide the equivalent insulating of cords complying with IEC 60227 or IEC 60245. (IEC 60335-2-80/A1) 9 STARTIG OF MOTOR-OERATED ALIACES Requirements and tests are specified in part 2 when necessary 10 OWER IUT AD CURRET 10.1 ower input at normal operating temperature, rated voltage and normal operation not deviating from rated power input by more than shown in table 1.: Test carried out at upper and lower limits of the ranges for appliances with one or more rated voltage ranges, unless the rated power input is related to the arithmetic mean value Appliances are tested with shutters or similar devices in the open position.() 10.2 Current at normal operating temperature, rated voltage and normal operation not deviating from rated current by more than shown in table 2...: Test carried out at upper and lower limits of the ranges for appliances with one or more rated voltage ranges, unless (see appended table) TRF o. IEC60335_2_80E
age 13 of 114 Report o.: STUESO017022702211HS the rated current is related to the arithmetic mean value of the range Appliances are tested with shutters or similar devices in the open position. () 11 HEATIG 11.1 o excessive temperatures in normal use 11.2 The appliance is held, placed or fixed in position as described...: 11.3 Temperature rises, other than of windings, determined by thermocouples Temperature rises of windings determined by resistance method, unless the windings are non-uniform or it is difficult to make the necessary connections 11.4 Heating appliances operated under normal operation at 1.15 times rated power input (W)...: 11.5 Motor-operated appliances operated under normal operation at most unfavourable voltage between 0.94 and 1.06 times rated voltage (V)...: 11.6 Combined appliances operated under normal operation at most unfavourable voltage between 0.94 and 1.06 times rated voltage (V)...: 11.7 Appliances are operated until steady conditions are established. () 11.8 Temperature rises monitored continuously and not exceeding the values in table 3...: If the temperature rise of a motor winding exceeds the value of table 3, or if there is doubt with regard to classification of insulation, tests of Annex C are carried out Sealing compound does not flow out rotective devices do not operate, except components in protective electronic circuits tested for the number of cycles specified in 24.1.4 The appliance is fixed to a vertical support according to instruction 1,06x240V=254,4V (see appended table) TRF o. IEC60335_2_80E
age 14 of 114 Report o.: STUESO017022702211HS The temperature rise limits for appliances for tropical climates are reduced by 15 K. (IEC 60335-2-80) The temperature rise limits for fans marked with an ambient operating temperature are reduced by the difference between the marked value and 25 C. (/A1) 13 LEAKAGE CURRET AD ELECTRIC STREGTH AT OERATIG TEMERATURE 13.1 Leakage current not excessive and electric strength adequate Heating appliances operated at 1.15 times the rated power input (W)...: Motor-operated appliances and combined appliances supplied at 1.06 times the rated voltage (V)...: rotective impedance and radio interference filters disconnected before carrying out the tests 13.2 For class 0, class II and class III appliances, leakage current measured by means of the circuit described in figure 4 of IEC 60990 For other appliances, a low impedance ammeter may be used 1,06x240V=254,4V Leakage current measurements...: (see appended table) 13.3 The appliance is disconnected from the supply Electric strength tests according to table 4...: (see appended table) o breakdown during the tests 14 TRASIET OVERVOLTAGES Appliances withstand the transient over-voltages to which they may be subjected Clearances having a value less than specified in table 16 subjected to an impulse voltage test, the test voltage specified in table 6...: o flashover during the test, unless of functional insulation if the appliance complies with clause 19 with the clearance short-circuited 15 MOISTURE RESISTACE 15.1 Enclosure provides the degree of moisture protection according to classification of the appliance TRF o. IEC60335_2_80E
age 15 of 114 Report o.: STUESO017022702211HS Compliance checked as specified in 15.1.1, taking into account 15.1.2, followed by the electric strength test of 16.3 o trace of water on insulation which can result in a reduction of clearances or creepage distances below values specified in clause 29 15.1.1 Appliances, other than IX0, subjected to tests as specified in IEC 60529...: Water valves containing live parts in external hoses for connection of an appliance to the water mains tested as specified for IX7 appliances The outer part of fans to be installed in the external structure is subjected to subclause 14.2.4(a) of IEC 60529. The outer part of fans is not to be installed in the external structure is protected against the water. (/A1) The fans supplied as rated voltage with shutters or similar devices being the open position. (IEC 60335-2-80/A1) 15.1.2 Hand-held appliance turned continuously through the most unfavourable positions during the test Built-in appliances installed according to the instructions Appliances placed or used on the floor or table placed on a horizontal unperforated support Appliances normally fixed to a wall and appliances with pins for insertion into socket-outlets are mounted on a wooden board For IX3 appliances, the base of wall mounted appliances is placed at the same level as the pivot axis of the oscillating tube For IX4 appliances, the horizontal centre line of the appliance is aligned with the pivot axis of the oscillating tube, and for appliances normally used on the floor or table, the movement is limited to two times 90 for a period of 5 min, the support being placed at the level of the pivot axis of the oscillating tube Wall-mounted appliances, take into account the distance to the floor stated in the instructions TRF o. IEC60335_2_80E
age 16 of 114 Report o.: STUESO017022702211HS Appliances normally fixed to a ceiling are mounted underneath a horizontal unperforated support, the pivot axis of the oscillating tube located at the level of the underside of the support, and for IX4 appliances, the movement of the tube is limited to two times 90 from the vertical for a period of 5 min Appliances with type X attachment fitted with a flexible cord as described Detachable parts subjected to the relevant treatment with the main part However, if a part has to be removed for user maintenance and a tool is needed, this part is not removed 15.2 Spillage of liquid does not affect the electrical insulation Appliances with type X attachment fitted with a flexible cord as described Appliances incorporating an appliance inlet tested with or without an connector, whichever is most unfavourable Detachable parts are removed Overfilling test with additional amount of water, over a period of 1 min (l)...: The appliance withstands the electric strength test of 16.3 o trace of water on insulation that can result in a reduction of clearances or creepage distances below values specified in clause 29 15.3 Appliances proof against humid conditions Checked by test Cab: Damp heat steady state in IEC 60068-2-78 Detachable parts removed and subjected, if necessary, to the humidity test with the main part Humidity test for 48 h in a humidity cabinet 25 C, 93% R.H. Reassembly of those parts that may have been removed The appliance withstands the tests of clause 16 16 LEAKAGE CURRET AD ELECTRIC STREGTH TRF o. IEC60335_2_80E
age 17 of 114 Report o.: STUESO017022702211HS 16.1 Leakage current not excessive and electric strength adequate rotective impedance disconnected from live parts before carrying out the tests Tests carried out at room temperature and not connected to the supply 16.2 Single-phase appliances: test voltage 1.06 times rated voltage (V)...: Three-phase appliances: test voltage 1.06 times rated voltage divided by 3 (V)...: 1,06x240V=254,4V Leakage current measurements...: (see appended table) Limit values doubled if: - all controls have an off position in all poles, or - the appliance has no control other than a thermal cut-out, or - all thermostats, temperature limiters and energy regulators do not have an off position, or - the appliance has radio interference filters With the radio interference filters disconnected, the leakage current do not exceed limits specified...: 16.3 Electric strength tests according to table 7...: (see appended table) Test voltage applied between the supply cord and inlet bushing and cord guard and cord anchorage as specified...: o breakdown during the tests (see appended table) 17 OVERLOAD ROTECTIO OF TRASFORMERS AD ASSOCIATED CIRCUITS o excessive temperatures in transformer or associated circuits in event of short-circuits likely to occur in normal use...: Appliance supplied with 1.06 or 0.94 times rated voltage under the most unfavourable short-circuit or overload likely to occur in normal use (V)...: Basic insulation is not short-circuited Temperature rise of insulation of the conductors of safety extra-low voltage circuits not exceeding the relevant value specified in table 3 by more than 15 K Temperature of the winding not exceeding the value specified in table 8 1,06x240V=254,4V TRF o. IEC60335_2_80E
age 18 of 114 Report o.: STUESO017022702211HS However, limits do not apply to fail-safe transformers complying with sub-clause 15.5 of IEC 61558-1 18 EDURACE Requirements and tests are specified in part 2 when necessary 19 ABORMAL OERATIO 19.1 The risk of fire, mechanical damage or electric shock under abnormal or careless operation obviated Electronic circuits so designed and applied that a fault will not render the appliance unsafe...: Appliances incorporating heating elements subjected to the tests of 19.2 and 19.3, and if the appliance also has a control that limit the temperature during clause 11 it is subjected to the test of 19.4, and if applicable, to the test of 19.5 Appliances incorporating TC heating elements are also subjected to the test of 19.6 Appliances incorporating motors subjected to the tests of 19.7 to 19.10, as applicable Appliances incorporating electronic circuits subjected to the tests of 19.11 and 19.12, as applicable Appliances incorporating contactors or relays subjected to the test of 19.14, being carried out before the tests of 19.11 Appliances incorporating voltage selector switches subjected to the test of 19.15 Unless otherwise specified, the tests are continued until a non-self-resetting thermal cut-out operates, or until steady conditions are established If a heating element or intentionally weak part becomes open-circuited, the relevant test is repeated on a second sample TRF o. IEC60335_2_80E
age 19 of 114 Report o.: STUESO017022702211HS Fans incorporating shutters or similar subjected to the test of cl. 19.101 () 19.2 Test of appliances with heating elements with restricted heat dissipation; test voltage (V), power input of 0.85 times rated power input (W)...: 19.3 Test of 19.2 repeated; test voltage (V), power input of 1.24 times rated power input (W)...: 19.4 Test conditions as in clause 11, any control limiting the temperature during tests of clause 11 short-circuited 19.5 Test of 19.4 repeated on Class 0I and I appliances with tubular sheathed or embedded heating elements. o short-circuiting, but one end of the element connected to the sheath The test repeated with reversed polarity and the other end of the heating element connected to the sheath The test is not carried out on appliances intended to be permanently connected to fixed wiring and on appliances where an all-pole disconnection occurs during the test of 19.4 19.6 Appliances with TC heating elements tested at rated voltage, establishing steady conditions The working voltage of the TC heating element is increased by 5% and the appliance is operated until steady conditions are re-established. The voltage is then increased in similar steps until 1.5 times working voltage or until the TC heating element ruptures (V)...: 19.7 Stalling test by locking the rotor if the locked rotor torque is smaller than the full load torque, or locking moving parts of other appliances Locked rotor, capacitors open-circuited one at a time Test repeated with capacitors short-circuited one at a time, unless capacitor is of class 2 of IEC 60252-1 Appliances with timer or programmer supplied with rated voltage for each of the tests, for a period equal to the maximum period allowed...: Other appliances supplied with rated voltage for a period as specified...: TRF o. IEC60335_2_80E
age 20 of 114 Report o.: STUESO017022702211HS Winding temperatures not exceeding values specified in table 8...: (see appended table) Mounting of separate control () Approximately 50 % of the area of each ventilating opening is blocked. () Winding temperatures not exceeding values specified in table 8 () (see appended table) The temperature rise of the board not exceed: () 50 K, for appliances with T marking; 65 K, for other appliances. 19.8 Multi-phase motors operated at rated voltage with one phase disconnected 19.9 ot applicable. () 19.10 Series motor operated at 1.3 times rated voltage for 1 min (V)...: During the test, parts not being ejected from the appliance 19.11 Electronic circuits, compliance checked by evaluation of the fault conditions specified in 19.11.2 for all circuits or parts of circuits, unless they comply with the conditions specified in 19.11.1 Appliances incorporating an electronic circuit that relies upon a programmable component to function correctly, subjected to the test of 19.11.4.8, unless restarting does not result in a hazard Appliances having a device with an off position obtained by electronic disconnection, or a device placing the appliance in a stand-by mode, subjected to the tests of 19.11.4 If the safety of the appliance under any of the fault conditions depends on the operation of a miniature fuse-link complying with IEC 60127, the test of 19.12 is carried out During and after each test the following is checked: - the temperature of the windings do not exceed the values specified in table 8 - the appliance complies with the conditions specified in 19.13 TRF o. IEC60335_2_80E
age 21 of 114 Report o.: STUESO017022702211HS - any current flowing through protective impedance not exceeding the limits specified in 8.1.4 If a conductor of a printed board becomes open-circuited, the appliance is considered to have withstood the particular test, provided both of the following conditions are met: - the base material of the printed circuit board withstands the test of Annex E - any loosened conductor does not reduce clearance or creepage distances between live parts and accessible metal parts below the values specified in clause 29 19.11.1 Fault conditions a) to g) in 19.11.2 are not applied to circuits or parts of circuits meeting both of the following conditions: - the electronic circuit is a low-power circuit, that is, the maximum power at low-power points does not exceed 15 W according to the tests specified - the protection against electric shock, fire hazard, mechanical hazard or dangerous malfunction of other parts of the appliance does not rely on the correct functioning of the electronic circuit 19.11.2 Fault conditions applied one at a time, the appliance operating under conditions specified in clause 11, but supplied at rated voltage, duration of the tests as specified: a) short circuit of functional insulation if clearances or creepage distances are less than the values specified in clause 29 b) open circuit at the terminals of any component c) short circuit of capacitors, unless they comply with IEC 60384-14 d) short circuit of any two terminals of an electronic component, other than integrated circuits This fault condition is not applied between the two circuits of an optocoupler e) failure of triacs in the diode mode f) failure of microprocessors and integrated circuits g) failure of an electronic power switching device Each low power circuit is short-circuited by connecting the low-power point to the pole of the supply source from which the measurements were made TRF o. IEC60335_2_80E
age 22 of 114 Report o.: STUESO017022702211HS 19.11.3 If the appliance incorporates a protective electronic circuit which operates to ensure compliance with clause 19, the relevant test is repeated with a single fault simulated, as indicated in a) to g) of 19.11.2 19.11.4 Appliances having a device with an off position obtained by electronic disconnection, or a device that can be placed in the stand-by mode, subjected to the tests of 19.11.4.1 to 19.11.4.7, the device being set in the off position or in the standby mode Appliances incorporating a protective electronic circuit subjected to the tests of 19.11.4.1 to 19.11.4.7, the tests being carried out after the protective electronic circuit has operated, except that appliances operated for 30 s or 5 min during the test of 19.7 are not subjected to the tests for electromagnetic phenomena. Surge protective devices disconnected, unless They incorporate spark gaps 19.11.4.1 The appliance is subjected to electrostatic discharges in accordance with IEC 61000-4-2, test level 4 19.11.4.2 The appliance is subjected to radiated fields in accordance with IEC 61000-4-3, test level 3 19.11.4.3 The appliance is subjected to fast transient bursts in accordance with IEC 61000-4-4, test level 3 or 4 as specified 19.11.4.4 The power supply terminals of the appliance subjected to voltage surges in accordance with IEC 61000-4-5, test level 3 or 4 as specified Earthed heating elements in class I appliances disconnected 19.11.4.5 The appliance is subjected to injected currents in accordance with IEC 61000-4-6, test level 3 19.11.4.6 Appliances having a rated current not exceeding 16 A are subjected to the Class 3 voltage dips and interruptions in accordance with IEC 61000-4-11 Appliances having a rated current exceeding 16 A are subjected to the Class 3 voltage dips and interruptions in accordance with IEC 61000-4-34 TRF o. IEC60335_2_80E
age 23 of 114 Report o.: STUESO017022702211HS 19.11.4.7 The appliance is subjected to mains signals in accordance with IEC 61000-4-13, test level class 2 19.11.4.8 The appliance is supplied at rated voltage and operated under normal operation. After 60s the power supply is reduced to a level such that the appliance ceases to respond or parts controlled by the programmable component cease to operate The appliance continues to operate normally, or requires a manual operation to restart 19.12 If the safety of the appliance for any of the fault conditions specified in 19.11.2 depends on the operation of a miniature fuse-link complying with IEC 60127, the test is repeated, measuring the current flowing through the fuse-link; measured current (A); rated current of the fuse-link (A)...: 19.13 During the tests the appliance does not emit flames, molten metal, poisonous or ignitable gas in hazardous amounts Temperature rises not exceeding the values shown in table 9...: Compliance with clause 8 not impaired If the appliance can still be operated it complies with 20.2 Copper is weak part (see appended table) Insulation, other than of class III appliances or class III constructions that do not contain live parts, withstands the electric strength test of 16.3, the test voltage as specified in table 4: - basic insulation (V)...: 1000V - supplementary insulation (V)...: - reinforced insulation (V)...: 3000V After operation or interruption of a control, clearances and creepage distances across the functional insulation withstand the electric strength test of 16.3, the test voltage being twice the working voltage The appliance does not undergo a dangerous malfunction, and no failure of protective electronic circuits, if the appliance is still operable Appliances tested with an electronic switch in the off position, or in the stand-by mode: - do not become operational, or TRF o. IEC60335_2_80E
age 24 of 114 Report o.: STUESO017022702211HS - if they become operational, do not result in a dangerous malfunction during or after the tests of 19.11.4 If the appliance contains lids or doors that are controlled by one or more interlocks, one of the interlocks may be released provided that: - the lid or door does not move automatically to an open position when the interlock is released, and - the appliance does not start after the cycle in which the interlock was released 19.14 Appliances operated under the conditions of clause 11, any contactor or relay contact operating under the conditions of clause 11 being short-circuited For a relay or contactor with more than one contact, all contacts are short-circuited at the same time A relay or contactor operating only to ensure the appliance is energized for normal use is not shortcircuited If more than one relay or contactor operates in clause 11, they are short-circuited in turn 19.15 For appliances with a mains voltage selector switch, the switch is set to the lowest rated voltage position and the highest value of rated voltage is applied 19.101 Fans incorporating shutters or similar that are operated automatically are supplied at rated voltage in the closed or open position, whichever is more unfavourable () 20 STABILITY AD MECHAICAL HAZARDS 20.1 Appliances having adequate stability Tilting test through an angle of 10, appliance placed on an inclined plane/horizontal support, not connected to the supply mains; appliance does not overturn Tilting test repeated on appliances with heating elements, angle of inclination increased to 15 ossible heating test in overturned position; temperature rise does not exceed values shown in table 9 ortable pedestal fans exceeding 1,7 m and exceeding 10 kg tested with a force of 40 at 1,5 m. () TRF o. IEC60335_2_80E
age 25 of 114 Report o.: STUESO017022702211HS 20.2 Moving parts adequately arranged or enclosed as to provide protection against personal injury rotective enclosures, guards and similar parts are non-detachable, and have adequate mechanical strength Enclosures that can be opened by overriding an interlock are considered to be detachable parts Self-resetting thermal cut-outs and overcurrent protective devices not causing a hazard by unexpected closure ot possible to touch dangerous moving parts with the test probe described 20.101 Fan blades, other than those for mounting at high level, shall be guarded, unless: () -they have a hardness less than D 60 Shore, or -they have a peripheral speed less than 15 m/s when the fan is supplied at rated voltage, or -the fan has a power output not exceeding 2 W when supplied at rated voltage. 21 MECHAICAL STREGTH 21.1 Appliance has adequate mechanical strength and is constructed as to withstand rough handling Checked by applying 3 blows to every point of the enclosure like to be weak, in accordance with test Ehb of IEC 60068-2-75, spring hammer test, with an impact energy of 0,5 J The appliance shows no damage impairing compliance with this standard, and compliance with 8.1, 15.1 and clause 29 not impaired If doubt, supplementary or reinforced insulation subjected to the electric strength test of 16.3 If necessary, repetition of groups of three blows on a new sample 21.2 Accessible parts of solid insulation having strength to prevent penetration by sharp implements Test not applicable if the thickness of supplementary insulation is at least 1 mm and reinforced insulation at least 2 mm The insulation is tested as specified, and does withstand the electric strength test of 16.3 Thickness of enclosure: 2,4mm (for switch box) TRF o. IEC60335_2_80E
age 26 of 114 Report o.: STUESO017022702211HS 21.101 Fan guards are subjected to a push and pull force of 20. Dangerous moving parts are not accessible () The test probe is applied with a force not exceeding 5. (/A2) 21.102 Ceiling fans have adequate strength. Load four times mass (...) () 22 COSTRUCTIO 22.1 Appliance marked with the first numeral of the I system, relevant requirements of IEC 60529 are fulfilled OTE 101 The enclosure defined in IEC 60529 does not include guards for fan blades. (IEC 60335-2-80) 22.2 Stationary appliance: means to ensure all-pole disconnection from the supply being provided: - a supply cord fitted with a plug, or - a switch complying with 24.3, or - a statement in the instruction sheet that a disconnection incorporated in the fixed wiring is to be provided, or - an appliance inlet Singe-pole switches and single-pole protective devices for the disconnection of heating elements in single-phase, permanently connected class 01 and class I appliances, connected to the phase conductor 22.3 Appliance provided with pins: no undue strain on socket-outlets Applied torque not exceeding 0.25 m ull force of 50 to each pin after the appliance has being placed in the heating cabinet; when cooled to room temperature the pins are not displaced by more than 1mm Each pin subjected to a torque of 0.4m; the pins are not rotating, unless rotating does not impair compliance with this standard TRF o. IEC60335_2_80E
age 27 of 114 Report o.: STUESO017022702211HS 22.4 Appliance for heating liquids and appliance causing undue vibration not provided with pins for insertion into socket-outlets 22.5 o risk of electric shock when touching the pins of the plug, for appliances having a capacitor with rated capacitance exceeding 0,1 F, the appliance being disconnected from the supply at the instant of voltage peak Voltage not exceeding 34 V 22.6 Electrical insulation not affected by condensing water or leaking liquid Electrical insulation of Class II appliances not affected if a hose ruptures or seal leaks In case of doubt, test as described 22.7 Adequate safeguards against the risk of excessive pressure in appliances containing liquid or gases or having steam-producing devices 22.8 Electrical connections not subject to pulling during cleaning of compartments to which access can be gained without the aid of a tool, and that are likely to be cleaned in normal use 22.9 Insulation, internal wiring, windings, commutators and slip rings not exposed to oil, grease or similar substances, unless the substance has adequate insulating properties 22.10 ot possible to reset voltage-maintained non-selfresetting thermal cut-outs by the operation of an automatic switching device incorporated within the appliance, if: - a non-self-resetting thermal cut-out is required by the standard, and - a voltage maintained non-self-resetting thermal cut-out is used to meet it on-self-resetting thermal motor protectors have a trip-free action, unless they are voltage maintained Reset buttons of non-self-resetting controls so located or protected that accidental resetting is unlikely TRF o. IEC60335_2_80E
age 28 of 114 Report o.: STUESO017022702211HS 22.11 Reliable fixing of non-detachable parts that provide the necessary degree of protection against electric shock, moisture or contact with moving parts Obvious locked position of snap-in devices used for fixing such parts o deterioration of the fixing properties of snap-in devices used in parts that are likely to be removed during installation or servicing The 50 force is not applied to clips used to fasten fan guards. () Instead, a force of 15 is applied in any direction to the clips in an attempt to release them. (IEC 60335-2-80) Tests as described For enclosure 50 push/pull for enclosure and button 22.12 Handles, knobs etc. fixed in a reliable manner Fixing in wrong position of handles, knobs etc. indicating position of switches or similar components not possible Axial force 15 applied to parts, the shape being so that an axial pull is unlikely to be applied Axial force 30 applied to parts, the shape being so that an axial pull is likely to be applied 22.13 Unlikely that handles, when gripped as in normal use, make the operator s hand touch parts having a temperature rise exceeding the value specified for handles which are held for short periods only 22.14 o ragged or sharp edges creating a hazard for the user in normal use, or during user maintenance o exposed pointed ends of self-tapping screws or other fasteners, likely to be touched by the user in normal use or during user maintenance 22.15 Storage hooks and the like for flexible cords smooth and well rounded 22.16 Automatic cord reels cause no undue abrasion or damage to the sheath of the flexible cord, no breakage of conductors strands and no undue wear of contacts Cord reel tested with 6000 operations, as specified Electric strength test of 16.3, voltage of 1000 V applied Button TRF o. IEC60335_2_80E
age 29 of 114 Report o.: STUESO017022702211HS 22.17 Spacers not removable from the outside by hand or by means of a screwdriver or a spanner 22.18 Current-carrying parts and other metal parts resistant to corrosion 22.19 Driving belts not relied upon to provide the required level of insulation, unless constructed to prevent inappropriate replacement 22.20 Direct contact between live parts and thermal insulation effectively prevented, unless material used is non-corrosive, non-hygroscopic and non-combustible 22.21 Wood, cotton, silk, ordinary paper and fibrous or hygroscopic material not used as insulation, unless impregnated This requirement does not apply to magnesium oxide and mineral ceramic fibres used for the electrical insulation of heating elements o such material 22.22 Appliances not containing asbestos 22.23 Oils containing polychlorinated biphenyl (CB) not used 22.24 Bare heating elements, except in class III appliances or class III constructions that do not contain live parts, adequately supported In case of rupture, the heating conductor is unlikely to come in contact with accessible metal parts 22.25 Sagging heating conductors, except in class III appliances or class III constructions that do not contain live parts, cannot come into contact with accessible metal parts 22.26 For class III constructions the insulation between parts operating at safety extra-low voltage and other live parts complies with the requirements for double or reinforced insulation 22.27 arts connected by protective impedance separated by double or reinforced insulation 22.28 Metal parts of Class II appliances conductively connected to gas pipes or in contact with water, separated from live parts by double or reinforced insulation TRF o. IEC60335_2_80E
age 30 of 114 Report o.: STUESO017022702211HS 22.29 Class II appliances permanently connected to fixed wiring so constructed that the required degree of access to live parts is maintained after installation 22.30 arts serving as supplementary or reinforced insulation fixed so that they cannot be removed without being seriously damaged, or so constructed that they cannot be replaced in an incorrect position, and so that if they are omitted, the appliance is rendered inoperable or manifestly incomplete 22.31 either clearances nor creepage distances over supplementary and reinforced insulation reduced below values specified in clause 29 as a result of wear either clearances nor creepage distances between live parts and accessible parts reduced below values for supplementary insulation if wires, screws etc. become loose 22.32 Supplementary and reinforced insulation constructed or protected against pollution so that clearances or creepage distances are not reduced below the values in clause 29 Supplementary insulation of natural or synthetic rubber resistant to ageing, or arranged and dimensioned so that creepage distances are not reduced below values specified in 29.2 Ceramic material not tightly sintered, similar materials or beads alone not used as supplementary or reinforced insulation Insulating material in which heating conductors are embedded is considered to be basic insulation, not reinforced insulation Oxygen bomb test at 70 C for 96 h and 16 h at room temperature 22.33 Conductive liquids that are or may become accessible in normal use and conductive liquids that are in contact with unearthed accessible metal parts are not in direct contact with live parts Electrodes not used for heating liquids For class II constructions, conductive liquids that are or may become accessible in normal use and conductive liquids that are in contact with unearthed accessible metal parts, not in direct contact with basic or reinforced insulation, unless TRF o. IEC60335_2_80E
age 31 of 114 Report o.: STUESO017022702211HS the reinforced insulation consists of at least 3 layers For class II constructions, conductive liquids which are in contact with live parts, not in direct contact with reinforced insulation, unless the reinforced insulation consists of at least 3 layers An air layer not used as basic or supplementary insulation in a double insulation system if likely to be bridged by leaking liquid 22.34 Shafts of operating knobs, handles, levers etc. not live, unless the shaft is not accessible when the part is removed 22.35 For other than class III constructions, handles, levers and knobs, held or actuated in normal use, not becoming live in the event of a failure of basic insulation Such parts being of metal, and their shafts or fixings are likely to become live in the event of a failure of basic insulation, are either adequately covered by insulation material or their accessible parts are separated from their shafts or fixings by supplementary insulation This requirement does not apply to handles, levers and knobs on stationary appliances, other than those of electrical components, provided they are reliably connected to an earthing terminal or earthing contact, or separated from live parts by earthed metal Insulating material covering metal handles, levers and knobs withstand the electric strength test of 16.3 for supplementary insulation 22.36 For appliances other than class III, handles continuously held in the hand in normal use so constructed that when gripped as in normal use, the operators hand is not likely to touch metal parts, unless they are separated from live parts by double or reinforced insulation 22.37 Capacitors in Class II appliances not connected to accessible metal parts and their casings, if of metal, separated from accessible metal parts by supplementary insulation, unless the capacitors comply with 22.42 TRF o. IEC60335_2_80E
age 32 of 114 Report o.: STUESO017022702211HS 22.38 Capacitors not connected between the contacts of a thermal cut-out 22.39 Lamp holders used only for the connection of lamps 22.40 Motor-operated appliances and combined appliances intended to be moved while in operation, or having accessible moving parts, fitted with a switch to control the motor. The actuating member of the switch being easily visible and accessible If the appliance cannot operate continuously, automatically or remotely without giving rise to a hazard, appliances for remote operation being fitted with a switch for stopping the operation. The actuating member of the switch being easily visible and accessible 22.41 o components, other than lamps, containing mercury 22.42 rotective impedance consisting of at least two separate components Values specified in 8.1.4 not exceeded if any one of the components are short-circuited or opencircuited Resistors checked by the test of 14.1 a) in IEC 60065 Capacitors checked by the tests for class Y capacitors in IEC 60384-14 22.43 Appliances adjustable for different voltages, accidental changing of the setting of the voltage unlikely to occur 22.44 Appliances not having an enclosure that is shaped or decorated like a toy 22.45 When air is used as reinforced insulation, clearances not reduced below the values specified in 29.1.3 due to deformation as a result of an external force applied to the enclosure 22.46 For programmable protective electronic circuits used to ensure compliance with the standard, the software contains measures to control the fault/error conditions in table R.1 Software that contains measures to control the fault/error conditions specified in table R.2 is to be specified in parts 2 for particular constructions or to address specific hazards TRF o. IEC60335_2_80E
age 33 of 114 Report o.: STUESO017022702211HS These requirements are not applicable to software used for functional purpose or compliance with clause 11 22.47 Appliances connected to the water mains withstand the water pressure expected in normal use o leakage from any part, including any inlet water hose 22.48 Appliances connected to the water mains constructed to prevent backsiphonage of nonpotable water 22.49 For remote operation, the duration of operation is to be set before the appliance can be started, unless the appliance switches off automatically or can operate continuously without hazard 22.50 Controls incorporated in the appliance take priority over controls actuated by remote operation 22.51 There is a control on the appliance manually adjusted to the setting for remote operation before the appliance can be operated in this mode There is a visual indication showing that the appliance is adjusted for remote operation These requirements not necessary on appliances that can operate as follows, without giving rise to a hazard: - continuously, or - automatically, or - remotely 22.52 Socket-outlets on appliances accessible to the user in accordance with the socket-outlet system used in the country in which the appliance is sold 22.101 Appliances having provision for attaching a luminaire incorporate appropriate terminals and internal wiring. () 23 ITERAL WIRIG 23.1 Wireways smooth and free from sharp edges Wires protected against contact with burrs, cooling fins etc. Wire holes in metal well-rounded or provided with bushings TRF o. IEC60335_2_80E
age 34 of 114 Report o.: STUESO017022702211HS Wiring effectively prevented from coming into contact with moving parts 23.2 Beads etc. on live wires cannot change their position, and are not resting on sharp edges Beads inside flexible metal conduits contained within an insulating sleeve 23.3 Electrical connections and internal conductors movable relatively to each other not exposed to undue stress Flexible metallic tubes not causing damage to insulation of conductors Open-coil springs not used Adequate insulating lining provided inside a coiled spring, the turns of which touch one another o damage after 100 000 flexings for conductors flexed during normal use and at rated voltage, or () 100 flexings for conductors flexed during user maintenance Electric strength test of 16.3, 1000 V between live parts and accessible metal parts ot more than 10% of the strands of any conductor broken, and not more than 30% for wiring supplying circuits that consume no more than 15W 23.4 Bare internal wiring sufficiently rigid and fixed 23.5 The insulation of internal wiring subjected to the supply mains voltage withstanding the electrical stress likely to occur in normal use Basic insulation electrically equivalent to the basic insulation of cords complying with IEC 60227 or IEC 60245, or no breakdown when a voltage of 2000 V is applied for 15 min between the conductor and metal foil wrapped around the insulation 23.6 Sleeving used as supplementary insulation on internal wiring retained in position by clamping at both ends, or be such that it can only be removed by breaking or cutting TRF o. IEC60335_2_80E
age 35 of 114 Report o.: STUESO017022702211HS 23.7 The colour combination green/yellow only used for earthing conductors 23.8 Aluminium wires not used for internal wiring 23.9 Stranded conductors not consolidated by soldering where they are subjected to contact pressure, unless the contact pressure is provided by spring terminals 23.10 The insulation and sheath of internal wiring, incorporated in external hoses for the connection of an appliance to the water mains, at least equivalent to that of light polyvinyl chloride sheathed flexible cord (60227 IEC 52) 24 COMOETS 24.1 Components comply with safety requirements in relevant IEC standards List of components...: (see appended table) If components have not been tested and found to comply with relevant IEC standard for the number of cycles specified, they are tested in accordance with 24.1.1 to 24.1.9 For components mentioned in 24.1.1 to 24.1.9 no additional tests specified in the relevant component standard are necessary other than those specified in 24.1.1 to 24.1.9 Components not tested and found to comply with relevant IEC standard and components not marked or not used in accordance with its marking, tested under the conditions occurring in the appliance Lampholders and starterholders that have not being tested and found to comply with the relevant IEC standard, tested as a part of the appliance and additionally according to the gauging and interchangeability requirements of the relevant IEC standard o additional tests specified for nationally standardized plugs such as those detailed in IEC/TR 60083 or connectors complying with the standard sheets of IEC 60320-1 and IEC 60309 24.1.1 Capacitors likely to be permanently subjected to the supply voltage and used for radio interference suppression or for voltage dividing, complying with IEC 60384-14 Approved TRF o. IEC60335_2_80E
age 36 of 114 Report o.: STUESO017022702211HS If the capacitors have to be tested, they are tested according to Annex F 24.1.2 Safety isolating transformers complying with IEC 61558-2-6 If they have to be tested, they are tested according to Annex G 24.1.3 Switches complying with IEC 61058-1, the number of cycles of operation being at least 10 000 If they have to be tested, they are tested according to Annex H If the switch operates a relay or contactor, the complete switching system is subjected to the test If the switch only operates a motor staring relay complying with IEC 60730-2-10 with the number of cycles of a least 10 000 as specified, the complete switching system need not be tested 24.1.4 Automatic controls complying with IEC 60730-1 with the relevant part 2. The number of cycles of operation being at least: - thermostats: 10 000 - temperature limiters: 1 000 - self-resetting thermal cut-outs: 300 - voltage maintained non-self-resetting thermal cut-outs: 1 000 - other non-self-resetting thermal cut-outs: 30 - timers: 3 000 - energy regulators: 10 000 The number of cycles for controls operating during clause 11 need not be declared, if the appliance meets the requirements of this standard when they are short-circuited Thermal motor protectors are tested in combination with their motor under the conditions specified in Annex D For water valves containing live parts and that are incorporated in external hoses for connection of an appliance to the water mains, the degree of protection declared for subclause 6.5.2 of IEC 60730-2-8 is IX7 24.1.5 Appliance couplers complying with IEC 60320-1 TRF o. IEC60335_2_80E
age 37 of 114 Report o.: STUESO017022702211HS However, for appliances classified higher than IX0, the appliance couplers complying with IEC 60320-2-3 Interconnection couplers complying with IEC 60320-2-2 24.1.6 Small lamp holders similar to E10 lampholders complying with IEC 60238, the requirements for E10 lampholders being applicable 24.1.7 For remote operation of the appliance via a telecommunication network, the relevant standard for the telecommunication interface circuitry in the appliance is IEC 62151 24.1.8 The relevant standard for thermal links is IEC 60691 Thermal links not complying with IEC 60691 are considered to be an intentionally weak part for the purposes of Clause 19 24.1.9 Contactors and relays, other than motor starting relays, tested as part of the appliance They are also tested in accordance with Clause 17 of IEC 60730-1, the number of cycles of operations in 24.1.4 selected according to the contactor or relay function in the appliance...: Approved Approved 24.2 Appliances not fitted with: - switches or automatic controls in flexible cords - devices causing the protective device in the fixed wiring to operate in the event of a fault in the appliance - thermal cut-outs that can be reset by soldering, unless the solder has a melding point of at least 230 C Switches or automatic controls in flexible cords are allowed for appliances not exceeding 25 W. (IEC 60335-2-80) 24.3 Switches intended for all-pole disconnection of stationary appliances are directly connected to the supply terminals and have a contact separation in all poles, providing full disconnection under overvoltage category III conditions TRF o. IEC60335_2_80E
age 38 of 114 Report o.: STUESO017022702211HS 24.4 lugs and socket-outlets for extra-low voltage circuits and heating elements, not interchangeable with plugs and socket-outlets listed in IEC/TR 60083 or IEC 60906-1 or with connectors and appliance inlets complying with the standard sheets of IEC 60320-1 24.5 Capacitors in auxiliary windings of motors marked with their rated voltage and capacitance, and used accordingly Voltage across capacitors in series with a motor winding does not exceed 1,1 times rated voltage, when the appliance is supplied at 1,1 times rated voltage under minimum load 24.6 Working voltage of motors connected to the supply mains and having basic insulation that is inadequate for the rated voltage of the appliance, not exceeding 42 V In addition, the motors comply with the requirements of Annex I 24.7 Detachable hose-sets for connection of appliances to the water mains comply with IEC 61770 They are supplied with the appliance Appliances intended to be permanently connected to the water mains not connected by a detachable hose-set 24.8 Motor running capacitors in appliances for which 30.2.3 is applicable and that are permanently connected in series with a motor winding, not causing a hazard in event of a failure Rated: 450V Measure: 397V Limit: 450V x 1,1=495V One or more of the following conditions are to be met: - the capacitors are of class 2 according to IEC 60252-1 - the capacitors are housed within a metallic or ceramic enclosure - the distance of separation of the outer surface to adjacent non-metallic parts exceeds 50 mm - adjacent non-metallic parts within 50 mm withstand the needle-flame test of Annex E - adjacent non-metallic parts within 50 mm classified as at least V-1 according to IEC 60695-11-10 TRF o. IEC60335_2_80E
age 39 of 114 Report o.: STUESO017022702211HS 24.101 Thermal cut-outs in duct fans in order to comply with cl. 19 are not self-resetting () 25 SULY COECTIO AD EXTERAL FLEXIBLE CORDS 25.1 Appliance not intended for permanent connection to fixed wiring, means for connection to the supply: - supply cord fitted with a plug, - an appliance inlet having at least the same degree of protection against moisture as required for the appliance, or - pins for insertion into socket-outlets 25.2 Appliance not provided with more than one means of connection to the supply mains Stationary appliance for multiple supply may be provided with more than one means of connection, provided electric strength test of 1250 V for 1 min between each means of connection causes no breakdown 25.3 Appliance intended to be permanently connected to fixed wiring provided with one of the following means for connection to the supply mains: - a set of terminals allowing the connection of a flexible cord - a fitted supply cord - a set of supply leads accommodated in a suitable compartment - a set of terminals for the connection of cables of fixed wiring, cross-sectional areas specified in 26.6, and the appliance allows the connection of the supply conductors after the appliance has been fixed to its support - a set of terminals and cable entries, conduit entries, knock-outs or glands, allowing connection of appropriate types of cable or conduit, and the appliance allows the connection of the supply conductors after the appliance has been fixed to its support For a fixed appliance constructed so that parts can be removed to facilitate easy installation, this requirement is met if it is possible to connect the fixed wiring without difficulty after a part of the appliance has been fixed to its support TRF o. IEC60335_2_80E
age 40 of 114 Report o.: STUESO017022702211HS 25.4 Cable and conduit entries, rated current of appliance not exceeding 16 A, dimension according to table 10 (mm)...: Introduction of conduit or cable does not reduce clearances or creepage distances below values specified in clause 29 25.5 Method for assembling the supply cord to the appliance: - type X attachment - type Y attachment - type Z attachment, if allowed in relevant part 2 Type X attachment, other than those with a specially prepared cord, not used for flat twin tinsel cords For multi-phase appliances supplied with a supply cord and that are intended to be permanently connected to fixed wiring, the supply cord is assembled to the appliance by type Y attachment - type Z attachment is allowed for portable fans (IEC 60335-2-80) 25.6 lugs fitted with only one flexible cord 25.7 Supply cords, other than for class III appliances, being one of the following types: - rubber sheathed (at least 60245 IEC 53) - polychloroprene sheathed (at least 60245 IEC 57) - cross-linked polyvinyl chloride sheathed (at least 60245 IEC 88) - polyvinyl chloride sheathed. ot used if they are likely to touch metal parts having a temperature rise exceeding 75 K during the test of clause 11 light polyvinyl chloride sheathed cord (60227 IEC 52), for appliances not exceeding 3 kg ordinary polyvinyl chloride sheathed cord (60227 IEC 53), for other appliances H05VV-F - heat resistant polyvinyl chloride sheathed. ot used for type X attachment other than specially prepared cords heat-resistant light polyvinyl chloride sheathed cord (60227 IEC 56), for appliances not exceeding 3 kg heat-resistant polyvinyl chloride sheathed cord (60227 IEC 57), for other appliances TRF o. IEC60335_2_80E
age 41 of 114 Report o.: STUESO017022702211HS Supply cords for class III appliances adequately insulated Test with 500 V for 2 min for supply cords of class III appliances that contain live parts 25.8 ominal cross-sectional area of supply cords not less than table 11; rated current (A); cross-sectional area (mm²)...: 25.9 Supply cords not in contact with sharp points or edges 25.10 Supply cord of class I appliances have a green/yellow core for earthing 25.11 Conductors of supply cords not consolidated by soldering where they are subject to contact pressure, unless the contact pressure is provided by spring terminals 25.12 Insulation of the supply cord not damaged when moulding the cord to part of the enclosure 25.13 Inlet openings so constructed as to prevent damage to the supply cord If the enclosure at the inlet opening is not of insulating material, a non-detachable lining or bushing complying with 29.3 for supplementary insulation provided If unsheathed supply cord, a similar additional bushing or lining is required, unless the appliance is class 0, or a class III appliance not containing live parts 25.14 Supply cords moved while in operation adequately protected against excessive flexing Flexing test, as described: Measure: 1,56A cross-sectional area: 3 x 0,75mm 2 - applied force ()...: - number of flexings...: The test does not result in: - short-circuit between the conductors, such that the current exceeds a value of twice the rated current - breakage of more than 10% of the strands of any conductor - separation of the conductor from its terminal TRF o. IEC60335_2_80E
age 42 of 114 Report o.: STUESO017022702211HS - loosening of any cord guard - damage to the cord or the cord guard - broken strands piercing the insulation and becoming accessible 25.15 For appliances with supply cord and appliances to be permanently connected to fixed wiring by a flexible cord, conductors of the supply cord relieved from strain, twisting and abrasion by use of cord anchorage The cord cannot be pushed into the appliance to such an extent that the cord or internal parts of the appliance can be damaged ull and torque test of supply cord, values shown in table 12: mass (kg); pull (); torque (not on automatic cord reel) (m)...: Cord not damaged and max. 2 mm displacement of the cord 100, 0,35m 0,5 mm 25.16 Cord anchorages for type X attachments constructed and located so that: - replacement of the cord is easily possible - it is clear how the relief from strain and the prevention of twisting are obtained - they are suitable for different types of supply cord - cord cannot touch the clamping screws of cord anchorage if these screws are accessible, unless they are separated from accessible metal parts by supplementary insulation - the cord is not clamped by a metal screw which bears directly on the cord - at least one part of the cord anchorage securely fixed to the appliance, unless it is part of a specially prepared cord - screws which have to be operated when replacing the cord do not fix any other component, unless the appliance becomes inoperative or incomplete or the parts cannot be removed without a tool - if labyrinths can be bypassed the test of 25.15 is nevertheless withstood - for class 0, 0I and I appliances they are of insulating material or are provided with an insulating lining, unless TRF o. IEC60335_2_80E
age 43 of 114 Report o.: STUESO017022702211HS failure of the insulation of the cord does not make accessible metal parts live - for class II appliances they are of insulating material, or if of metal, they are insulated from accessible metal parts by supplementary insulation After the test of 25.15, under the conditions specified, the conductors have not moved by more than 1 mm in the terminals 25.17 Adequate cord anchorages for type Y and Z attachment, test with the cord supplied with the appliance 25.18 Cord anchorages only accessible with the aid of a tool, or Constructed so that the cord can only be fitted with the aid of a tool 25.19 Type X attachment, glands not used as cord anchorage in portable appliances Tying the cord into a knot or tying the cord with string not used 25.20 The insulated conductors of the supply cord for type Y and Z attachment additionally insulated from accessible metal parts Type Y 25.21 Space for supply cord for type X attachment or for connection of fixed wiring constructed: - to permit checking of conductors with respect to correct positioning and connection before fitting any cover - so there is no risk of damage to the conductors or their insulation when fitting the cover - for portable appliances, so that the uninsulated end of a conductor, if it becomes free from the terminal, prevented from contact with accessible metal parts 2 test to the conductor for portable appliances; no contact with accessible metal parts 25.22 Appliance inlets: - live parts not accessible during insertion or removal Requirement not applicable to appliance inlets complying with IEC 60320-1 TRF o. IEC60335_2_80E
age 44 of 114 Report o.: STUESO017022702211HS - connector can be inserted without difficulty - the appliance is not supported by the connector - not for cold conditions if temp. rise of external metal parts exceeds 75 K during clause 11, unless the supply cord is unlikely to touch such metal parts 25.23 Interconnection cords comply with the requirements for the supply cord, except that: - the cross-sectional area of the conductors is determined on the basis of the maximum current during clause 11 - the thickness of the insulation may be reduced If necessary, electric strength test of 16.3 25.24 Interconnection cords not detachable without the aid of a tool if compliance with this standard is impaired when they are disconnected 25.25 Dimensions of pins that are inserted into socketoutlets compatible with the dimensions of the relevant socket-outlet. Dimensions of pins and engagement face in accordance with the dimensions of the relevant plug in IEC/TR 60083 26 TERMIALS FOR EXTERAL CODUCTORS 26.1 Appliances provided with terminals or equally effective devices for connection of external conductors Terminals only accessible after removal of a nondetachable cover, except for class III appliances that do not contain live parts Earthing terminals may be accessible if a tool is required to make the connections and means are provided to clamp the wire independently from its connection 26.2 Appliances with type X attachment and appliances for the connection of cables to fixed wiring provided with terminals in which connections are made by means of screws, nuts or similar devices, unless the connections are soldered Screws and nuts not used to fix any other component, except TRF o. IEC60335_2_80E
age 45 of 114 Report o.: STUESO017022702211HS internal conductors, if so arranged that they are unlikely to be displaced when fitting the supply conductors If soldered connections used, the conductor so positioned or fixed that reliance is not placed on soldering alone, unless barriers provided so that neither clearances nor creepage distances between live parts and other metal parts reduced below the values for supplementary insulation if the conductor becomes free at the soldered joint 26.3 Terminals for type X attachment and for connection of cables of fixed wiring so constructed that the conductor is clamped between metal surfaces with sufficient contact pressure but without damaging the conductor Terminals fixed so that when the clamping means is tightened or loosened: - the terminal does not become loose - internal wiring is not subjected to stress - neither clearances nor creepage distances are reduced below the values in clause 29 Compliance checked by inspection and by the test of subclause 9.6 of IEC 60999-1, the torque applied being equal to two-thirds of the torque specified (m)...: o deep or sharp indentations of the conductors 26.4 Terminals for type X attachment, except those having a specially prepared cord and those for the connection of cables of fixed wiring, no special preparation of conductors such as by soldering, use of cable lugs, eyelets or similar, and so constructed or placed that conductors prevented from slipping out when clamping screws or nuts are tightened 26.5 Terminals for type X attachment so located or shielded that if a wire of a stranded conductor escapes, no risk of accidental connection to other parts that result in a hazard Stranded conductor test, 8 mm insulation removed o contact between live parts and accessible metal parts and, TRF o. IEC60335_2_80E
age 46 of 114 Report o.: STUESO017022702211HS for class II constructions, between live parts and metal parts separated from accessible metal parts by supplementary insulation only 26.6 Terminals for type X attachment and for connection of cables of fixed wiring suitable for connection of conductors with cross-sectional area according to table 13; rated current (A); nominal cross-sectional area (mm²)...: If a specially prepared cord is used, terminals need only be suitable for that cord 26.7 Terminals for type X attachment, except in class III appliances not containing live parts, accessible after removal of a cover or part of the enclosure 26.8 Terminals for the connection of fixed wiring, including the earthing terminal, located close to each other 26.9 Terminals of the pillar type constructed and located as specified 26.10 Terminals with screw clamping and screwless terminals not used for flat twin tinsel cords, unless conductors ends fitted with means suitable for screw terminals ull test of 5 to the connection 26.11 For type Y and Z attachment, soldered, welded, crimped or similar connections may be used For Class II appliances, the conductor so positioned or fixed that reliance is not placed on soldering, welding or crimping alone If soldering, welding or crimping alone used, barriers provided so that clearances and creepage distances between live parts and other metal parts are not reduced below the values for supplementary insulation if the conductor becomes free 27 ROVISIO FOR EARTHIG 27.1 Accessible metal parts of Class 0I and I appliances permanently and reliably connected to an earthing terminal or earthing contact of the appliance inlet Earthing terminals and earthing contacts not connected to the neutral terminal Class 0, II and III appliances have no provision for earthing TRF o. IEC60335_2_80E
age 47 of 114 Report o.: STUESO017022702211HS Safety extra-low voltage circuits not earthed, unless protective extra-low voltage circuits 27.2 Clamping means of earthing terminals adequately secured against accidental loosening Terminals for the connection of external equipotential bonding conductors allow connection of conductors of 2.5 to 6 mm², and do not provide earthing continuity between different parts of the appliance, and conductors cannot be loosened without the aid of a tool 27.3 For a detachable part having an earth connection and being plugged into another part of the appliance, the earth connection is made before and separated after current-carrying connections when removing the part For appliances with supply cords, current-carrying conductors become taut before earthing conductor, if the cord slips out of the cord anchorage 27.4 o risk of corrosion resulting from contact between parts of the earthing terminal and the copper of the earthing conductor or other metal arts providing earthing continuity, other than parts of a metal frame or enclosure, have adequate resistance to corrosion If of steel, these parts provided with an electroplated coating with a thickness at least 5 µm Adequate protection against rusting of parts of coated or uncoated steel, only intended to provide or transmit contact pressure In the body of the earthing terminal is a part of a frame or enclosure of aluminium or aluminium alloys, precautions taken to avoid risk of corrosion 27.5 Low resistance of connection between earthing terminal and earthed metal parts This requirement does not apply to connections providing earthing continuity in the protective extralow voltage circuit, provided the clearances of basic insulation are based on the rated voltage of the appliance Resistance not exceeding 0,1 Ω at the specified low-resistance test (Ω )...: 0,035Ω TRF o. IEC60335_2_80E
age 48 of 114 Report o.: STUESO017022702211HS 27.6 The printed conductors of printed circuit boards not used to provide earthing continuity in hand-held appliances. They may be used to provide earthing continuity in other appliances if at least two tracks are used with independent soldering points and the appliance complies with 27.5 for each circuit 28 SCREWS AD COECTIOS 28.1 Fixings, electrical connections and connections providing earthing continuity withstand mechanical stresses Screws not of soft metal liable to creep, such as zinc or aluminium Diameter of screws of insulating material min. 3 mm Screws of insulating material not used for any electrical connections or connections providing earthing continuity Screws used for electrical connections or connections providing earthing continuity screwed into metal Screws not of insulating material if their replacement by a metal screw can impair supplementary or reinforced insulation For type X attachment, screws to be removed for replacement of supply cord or for user maintenance, not of insulating material if their replacement by a metal screw impairs basic insulation For screws and nuts; torque-test as specified in table 14...: 28.2 Electrical connections and connections providing earthing continuity constructed so that contact pressure is not transmitted through non-ceramic insulating material liable to shrink or distort, unless there is resiliency in the metallic parts to compensate for shrinkage or distortion of the insulating material (see appended table) This requirement does not apply to electrical connections in circuits of appliances for which: 30.2.2 is applicable and that carry a current not exceeding 0,5 A TRF o. IEC60335_2_80E
age 49 of 114 Report o.: STUESO017022702211HS 30.2.3 is applicable and that carry a current not exceeding 0,2 A 28.3 Space-threaded (sheet metal) screws only used for electrical connections if they clamp the parts together Thread-cutting (self-tapping) screws and thread rolling screws only used for electrical connections if they generate a full form standard machine screw thread Thread-cutting (self-tapping) screws not used if they are likely to be operated by the user or installer Thread-cutting, thread rolling and space threaded screws may be used in connections providing earthing continuity provided it is not necessary to disturb the connection: - in normal use, - during user maintenance, - when replacing a supply cord having a type X attachment, or - during installation At least two screws being used for each connection providing earthing continuity, unless the screw forms a thread having a length of at least half the diameter of the screw 28.4 Screws and nuts that make mechanical connection secured against loosening if they also make electrical connections or connections providing earthing continuity This requirement does not apply to screws in the earthing circuit if at least two screws are used, or if an alternative earthing circuit is provided Rivets for electrical connections or connections providing earthing continuity secured against loosening if the connections are subjected to torsion 29 CLEARACES, CREEAGE DISTACES AD SOLID ISULATIO Clearances, creepage distances and solid insulation withstand electrical stress For coatings used on printed circuits boards to protect the microenvironment (Type 1) or to provide basic insulation (Type 2), Annex J applies...: TRF o. IEC60335_2_80E
age 50 of 114 Report o.: STUESO017022702211HS The microenvironment is pollution degree 1 under type 1 protection For type 2 protection, the spacing between the conductors before the protection is applied is not less than the values specified in Table 1 of IEC 60664-3 These values apply to functional, basic, supplementary and reinforced insulation...: 29.1 Clearances not less than the values specified in table 16, taking into account the rated impulse voltage for the overvoltage categories of table 15, unless...: for basic insulation and functional insulation they comply with the impulse voltage test of clause 14 However, if the distances are affected by wear, distortion, movement of the parts or during assembly, the clearances for rated impulse voltages of 1500V and above are increased by 0,5 mm and the impulse voltage test is not applicable Impulse voltage test is not applicable: - when the microenvironment is pollution degree 3, or - for basic insulation of class 0 and class 01 appliances Appliances are in overvoltage category II A force of 2 is applied to bare conductors, other than heating elements A force of 30 is applied to accessible surfaces 29.1.1 Clearances of basic insulation withstand the overvoltages, taking into account the rated impulse voltage The values of table 16 or the impulse voltage test of clause 14 are applicable...: Clearance at the terminals of tubular sheathed heating elements may be reduced to 1,0 mm if the microenvironment is pollution degree 1 Lacquered conductors of windings considered to be bare conductors 29.1.2 Clearances of supplementary insulation not less than those specified for basic insulation in table 16 : (see appended table) (see appended table) (see appended table) TRF o. IEC60335_2_80E
age 51 of 114 Report o.: STUESO017022702211HS 29.1.3 Clearances of reinforced insulation not less than those specified for basic insulation in table 16, using the next higher step for rated impulse voltage...: For double insulation, with no intermediate conductive part between basic and supplementary insulation, clearances are measured between live parts and the accessible surface, and the insulation system is treated as reinforced insulation (see appended table) 29.1.4 Clearances for functional insulation are the largest values determined from: - table 16 based on the rated impulse voltage...: (see appended table) - table F.7a in IEC 60664-1, frequency not exceeding 30 khz - clause 4 of IEC 60664-4, frequency exceeding 30 khz If values of table 16 are largest, the impulse voltage test of clause 14 may be applied instead, unless the microenvironment is pollution degree 3, or the distances can be affected by wear, distortion, movement of the parts or during assembly However, clearances are not specified if the appliance complies with clause 19 with the functional insulation short-circuited Lacquered conductors of windings considered to be bare conductors However, clearances at crossover points are not measured Clearance between surfaces of TC heating elements may be reduced to 1mm 29.1.5 Appliances having higher working voltages than rated voltage, clearances for basic insulation are the largest values determined from: - table 16 based on the rated impulse voltage...: - table F.7a in IEC 60664-1, frequency not exceeding 30 khz - clause 4 of IEC 60664-4, frequency exceeding 30 khz If clearances for basic insulation are selected from Table F.7a of IEC 60664-1 or Clause 4 of IEC 60664-4, the clearances of supplementary insulation are not less than those specified for basic insulation TRF o. IEC60335_2_80E
age 52 of 114 Report o.: STUESO017022702211HS If clearances for basic insulation are selected from Table F.7a of IEC 60664-1, the clearances of reinforced insulation dimensioned as specified in Table F.7a are to withstand 160% of the withstand voltage required for basic insulation If clearances for basic insulation are selected from Clause 4 of IEC 60664-4, the clearances of reinforced insulation are twice the value required for basic insulation If the secondary winding of a step-down transformer is earthed, or if there is an earthed screen between the primary and secondary windings, clearances of basic insulation on the secondary side not less than those specified in table 16, but using the next lower step for rated impulse voltage Circuits supplied with a voltage lower than rated voltage, clearances of functional insulation are based on the working voltage used as the rated voltage in table 15 29.2 Creepage distances not less than those appropriate for the working voltage, taking into account the material group and the pollution degree...: ollution degree 2 applies, unless - precautions taken to protect the insulation; pollution degree 1 - insulation subjected to conductive pollution; pollution degree 3 Microenvironment is pollution degree 3 unless insulation is enclosed or located that it is unlikely to be exposed to pollution during normal use. (IEC 60335-2-80) A force of 2 is applied to bare conductors, other than heating elements A force of 30 is applied to accessible surfaces In a double insulation system, the working voltage for both the basic and supplementary insulation is taken as the working voltage across the complete double insulation system 29.2.1 Creepage distances of basic insulation not less than specified in table 17...: (see appended table) (see appended table) TRF o. IEC60335_2_80E
age 53 of 114 Report o.: STUESO017022702211HS However, if the working voltage is periodic and has a frequency exceeding 30 khz, the creepage distances are also determined from table 2 of IEC 60664-4, these values being used if exceeding the values in table 17...: Except for pollution degree 1, corresponding creepage distance not less than the minimum specified for the clearance in table 16, if the clearance has been checked according to the test of clause 14...: 29.2.2 Creepage distances of supplementary insulation at least those specified for basic insulation in table 17, or...: (see appended table) Table 2 of IEC 60664-4, as applicable...: 29.2.3 Creepage distances of reinforced insulation at least double those specified for basic insulation in table 17, or...: Table 2 of IEC 60664-4, as applicable...: 29.2.4 Creepage distances of functional insulation not less than specified in table 18...: However, if the working voltage is periodic and has a frequency exceeding 30 khz, the creepage distances are also determined from table 2 of IEC 60664-4, these values being used if exceeding the values in table 18...: Creepage distances may be reduced if the appliance complies with clause 19 with the functional insulation short-circuited 29.3 Supplementary and reinforced insulation have adequate thickness, or a sufficient number of layers, to withstand the electrical stresses Compliance checked: (see appended table) (see appended table) - by measurement, in accordance with 29.3.1, or - by an electric strength test in accordance with 29.3.2, or - by an assessment of the thermal quality of the material combined with an electric strength test, in accordance with 29.3.3, and for accessible parts of reinforced insulation consisting of a single layer, by measurement in accordance with 29.3.4, or TRF o. IEC60335_2_80E
age 54 of 114 Report o.: STUESO017022702211HS - as specified in subclause 6.3 of IEC 60664-4 for insulation that is subjected to any periodic voltage having a frequency exceeding 30 khz 29.3.1 Supplementary insulation have a thickness of at least 1 mm Reinforced insulation have a thickness of at least 2 mm 29.3.2 Each layer of material withstand the electric strength test of 16.3 for supplementary insulation Supplementary insulation consist of at least 2 layers Reinforced insulation consist of at least 3 layers 29.3.3 The insulation is subjected to the dry heat test Bb of IEC 60068-2-2, followed by the electric strength test of 16.3 If the temperature rise during the tests of clause 19 does not exceed the value specified in table 3, the test of IEC 60068-2-2 is not carried out 29.3.4 Thickness of accessible parts of reinforced insulation consisting of a single layer not less than specified in table 19...: 30 RESISTACE TO HEAT AD FIRE 30.1 External parts of non-metallic material, parts supporting live parts, and parts of thermoplastic material providing supplementary or reinforced insulation sufficiently resistant to heat Ball-pressure test according to IEC 60695-10-2 External parts tested at 40 C plus the maximum temperature rise determined during the test of clause 11, or at 75 C, whichever is the higher; temperature ( C)...: arts supporting live parts tested at 40 C plus the maximum temperature rise determined during the test of clause 11, or at 125 C, whichever is the higher; temperature ( C)...: arts of thermoplastic material providing supplementary or reinforced insulation tested at 25 C plus the maximum temperature rise determined during clause 19, if higher; temperature ( C)...: (see appended table) (see appended table) TRF o. IEC60335_2_80E
age 55 of 114 Report o.: STUESO017022702211HS 30.2 arts of non-metallic material resistant to ignition and spread of fire This requirement does not apply to: parts having a mass not exceeding 0,5 g, provided the cumulative effect is unlikely to propagate flames that originate inside the appliance by propagating flames from one part to another, or decorative trims, knobs and other parts unlikely to be ignited or to propagate flames that originate inside the appliance Compliance checked by the tests of 30.2.1 and 30.2.3 For base material of printed circuit boards, 30.2.4 applies 30.2.1 arts of non-metallic material subjected to the glow-wire test of IEC 60695-2-11 at 550 C However, test not carried out if the material is classified as having a glow-wire flammability index according to IEC 60695-2-12 of at least 550 C, or the material is classified at least HB40 according to IEC 60695-11-10 arts for which the glow-wire test cannot be carried out need to meet the requirements in ISO 9772 for material classified HBF (see appended table) 30.2.2 ot applicable. () 30.2.3 Appliances operated while unattended, tested as specified in 30.2.3.1 and 30.2.3.2 The tests are not applicable to conditions as specified...: 30.2.3.1 arts of non-metallic material supporting connections carrying a current exceeding 0,2 A during normal operation, and parts of non-metallic material, other than small parts, within a distance of 3 mm, subjected to the glow-wire test of IEC 60695-2-11 with a test severity of 850 C Glow-wire applied to an interposed shielding material, if relevant (see appended table) TRF o. IEC60335_2_80E
age 56 of 114 Report o.: STUESO017022702211HS The glow-wire test is not carried out on parts of material classified as having a glow-wire flammability index according to IEC 60695-2-12 of at least 850 C 30.2.3.2 arts of non-metallic material supporting connections, and parts of non-metallic material within a distance of 3mm, subjected to glow-wire test of IEC 60695-2-11 The test severity is: - 750 C, for connections carrying a current exceeding 0,2 A during normal operation (see appended table) - 650 C, for other connections Glow-wire applied to an interposed shielding material, if relevant However, the glow-wire test of 750 C or 650 C as appropriate, is not carried out on parts of material fulfilling both or either of the following classifications: - a glow-wire ignition temperature according to IEC 60695-2-13 of at least: 775 C, for connections carrying a current exceeding 0,2 A during normal operation 675 C, for other connections - a glow-wire flammability index according to IEC 60695-2-12 of at least: - 750 C, for connections carrying a current exceeding 0,2 A during normal operation - 650 C, for other connections The glow-wire test is also not carried out on small parts. These parts are to: - comprise material having a glow-wire ignition temperature of at least 775 C or 675 C as appropriate, or - comprise material having a glow-wire flammability index of at least 750 C or 650 C as appropriate, or - comply with the needle-flame test of Annex E, or - comprise material classified as V-0 or V-1 according to IEC 60695-11-10 TRF o. IEC60335_2_80E
age 57 of 114 Report o.: STUESO017022702211HS The consequential needle-flame test of Annex E applied to non-metallic parts that encroach within the vertical cylinder placed above the centre of the connection zone and on top of the non-metallic parts supporting current-carrying connections, and parts of non-metallic material within a distance of 3 mm of such connections if these parts are those: - parts that withstood the glow-wire test of IEC 60695-2-11 of 750 C or 650 C as appropriate, but produce a flame that persist longer than 2 s, or - parts that comprised material having a glow-wire flammability index of at least 750 C or 650 C as appropriate, or - small parts, that comprised material having a glow-wire flammability index of at least 750 C or 650 C as appropriate, or - small parts for which the needle-flame test of Annex E was applied, or - small parts for which a material classification of V- 0 or V-1 was applied However, the consequential needle-flame test is not carried out on non-metallic parts, including small parts, within the cylinder that are: - parts having a glow-wire ignition temperature of at least 775 C or 675 C as appropriate, or - parts comprising material classified as V-0 or V-1 according to IEC 60695-11-10, or - parts shielded by a flame barrier that meets the needle-flame test of Annex E or that comprises material classified as V-0 or V-1 according to IEC 60695-11-10 30.2.4 Base material of printed circuit boards subjected to the needle-flame test of Annex E Test not applicable to conditions as specified...: 31 RESISTACE TO RUSTIG Relevant ferrous parts adequately protected against rusting Tests specified in part 2 when necessary 32 RADIATIO, TOXICITY AD SIMILAR HAZARDS Appliance does not emit harmful radiation or present a toxic or similar hazard due to their operation in normal use TRF o. IEC60335_2_80E
age 58 of 114 Report o.: STUESO017022702211HS Compliance is checked by the limits or tests specified in part 2, if relevant A B AEX A (IFORMATIVE) ROUTIE TESTS Description of routine tests to be carried out by the manufacturer AEX B (ORMATIVE) ALIACES OWERED BY RECHARGEABLE BATTERIES The following modifications to this standard are applicable for appliances powered by batteries that are recharged in the appliance This annex does not apply to battery chargers 3.1.9 Appliance operated under the following conditions: - the appliance, supplied by its fully charged battery, operated as specified in relevant part 2 - the battery is charged, the battery being initially discharged to such an extent that the appliance cannot operate -if possible, the appliance is supplied from the supply mains through its battery charger, the battery being initially discharged to such an extent that the appliance cannot operate. The appliance is operated as specified in relevant part 2 - if the appliance incorporates inductive coupling between two parts that are detachable from each other, the appliance is supplied from the supply mains with the detachable part removed 3.6.2 art to be removed in order to discard the battery is not considered to be detachable 5.B.101 Appliances supplied from the supply mains tested as specified for motor-operated appliances 7.1 Battery compartment for batteries intended to be replaced by the user, marked with battery voltage and polarity of the terminals The positive terminal indicated by symbol IEC 60417-5005 and the negative terminal by symbol IEC 60417-5006 7.6 Symbols 60417-5005 and IEC 60417-5006 7.12 The instructions give information regarding charging TRF o. IEC60335_2_80E
age 59 of 114 Report o.: STUESO017022702211HS The instructions for appliances incorporating batteries intended to be replaced by the user includes required information Details about how to remove batteries containing materials hazardous to the environment given 7.15 Markings placed on the part of the appliance connected to the supply mains 8.2 Appliances having batteries that according to the instruction may be replaced by the user need only have basic insulation between live parts and the inner surface of the battery compartment If the appliance can be operated without batteries, double or reinforced insulation required 11.7 The battery is charged for the period stated in the instructions or 24 h...: 19.1 Appliances subjected to tests of 19.B.101, 19.B.102 and 19.B.103 19.10 ot applicable 19.B.101 19.B.102 19.B.103 21.B.101 Appliances supplied at rated voltage for 168 h, the battery being continually charged For appliances having batteries that can be removed without the aid of a tool, short-circuit of the terminals of the battery, the battery being fully charged, Appliances having batteries replaceable by the user supplied at rated voltage under normal operation with the battery removed or in any position allowed by the construction Appliances having pins for insertion into socketoutlets have adequate mechanical strength art of the appliance incorporating the pins subjected to the free fall test, procedure 2, of IEC 60068-2-31, the number of falls being: - 100, if the mass of the part does not exceed 250 g (g)...: - 50, if the mass of the part exceeds 250 g...: After the test, the requirements of 8.1, 15.1.1, 16.3 and clause 29 are met 22.3 Appliances having pins for insertion into socketoutlets tested as fully assembled as possible TRF o. IEC60335_2_80E
age 60 of 114 Report o.: STUESO017022702211HS 25.13 An additional lining or bushing not required for interconnection cords in class III appliances or class III constructions operating at safety extra-low voltage not containing live parts 30.2 For parts of the appliance connected to the supply mains during the charging period, 30.2.3 applies C D E For other parts, 30.2.2 applies AEX C (ORMATIVE) AGEIG TEST O MOTORS Tests, as described, carried out when doubt with regard to the temperature classification of the insulation of a motor winding Test conditions as specified AEX D (ORMATIVE) THERMAL MOTOR ROTECTORS Applicable to appliances having motors that incorporate thermal motor protectors necessary for compliance with the standard Test conditions as specified AEX E (ORMATIVE) EEDLE-FLAME TEST eedle-flame test carried out in accordance with IEC 60695-11-5, with the following modifications: 7 Severities The duration of application of the test flame is 30 s ± 1 s 9 Test procedure 9.1 The specimen so arranged that the flame can be applied to a vertical or horizontal edge as shown in the examples of Figure 1 9.2 The first paragraph does not apply If possible, the flame is applied at least 10 mm from a corner 9.3 The test is carried out on one specimen If the specimen does not withstand the test, the test may be repeated on two additional specimens, both withstanding the test 11 Evaluation of test results The duration of burning not exceeding 30 s TRF o. IEC60335_2_80E
age 61 of 114 Report o.: STUESO017022702211HS However, for printed circuit boards, the duration of burning not exceeding 15 s For CB F AEX F (ORMATIVE) CAACITORS Capacitors likely to be permanently subjected to the supply voltage, and used for radio interference suppression or voltage dividing, comply with the following clauses of IEC 60384-14, with the following modifications: 1.5 Terms and definitions 1.5.3 Class X capacitors tested according to subclass X2 1.5.4 This subclause is applicable 1.6 Marking Items a) and b) are applicable 3.4 Approval testing 3.4.3.2 Table 3 is applicable as described 4.1 Visual examination and check of dimensions This subclause is applicable 4.2 Electrical tests 4.2.1 This subclause is applicable 4.2.5 This subclause is applicable 4.2.5.2 Only table 11 is applicable Values for test A apply However, for capacitors in heating appliances the values for test B or C apply 4.12 Damp heat, steady state This subclause is applicable Only insulation resistance and voltage proof are checked 4.13 Impulse voltage This subclause is applicable 4.14 Endurance Subclauses 4.14.1, 4.14.3, 4.14.4 and 4.14.7 are applicable 4.14.7 Only insulation resistance and voltage proof are checked o visible damage TRF o. IEC60335_2_80E
age 62 of 114 Report o.: STUESO017022702211HS 4.17 assive flammability test This subclause is applicable 4.18 Active flammability test G This subclause is applicable AEX G (ORMATIVE) SAFETY ISOLATIG TRASFORMERS The following modifications to this standard are applicable for safety isolating transformers: 7 Marking and instructions 7.1 Transformers for specific use marked with: -name, trademark or identification mark of the manufacturer or responsible vendor...: -model or type reference...: 17 Overload protection of transformers and associated circuits Fail-safe transformers comply with subclause 15.5 of IEC 61558-1 22 Construction Subclauses 19.1 and 19.1.2 of IEC 61558-2-6 are applicable 29 Clearances, creepage distances and solid insulation 29.1, 29.2, 29.3 H The distances specified in items 2a, 2c and 3 in table 13 of IEC 61558-1 apply For insulated winding wires complying with subclause 19.12.3 of IEC 61558-1 there are no requirements for clearances or creepage distances For windings providing reinforced insulation, the distance specified in item 2c of table 13 of IEC 61558-1 is not assessed For safety isolating transformers subjected to periodic voltages with a frequency exceeding 30 khz, the clearances, creepage distances and solid insulation values specified in IEC 60664-4 are applicable, if greater than the values specified in items 2a, 2c and 3 in table 13 of IEC 61558-1 AEX H (ORMATIVE) SWITCHES Switches comply with the following clauses of IEC 61058-1, as modified below: TRF o. IEC60335_2_80E
age 63 of 114 Report o.: STUESO017022702211HS The tests of IEC 61058-1 carried out under the conditions occurring in the appliance Before being tested, switches are operated 20 times without load 8 Marking and documentation Switches are not required to be marked However, a switch that can be tested separately from the appliance marked with the manufacturer s name or trade mark and the type reference 13 Mechanism The tests may be carried out on a separate sample 15 Insulation resistance and dielectric strength 15.1 ot applicable 15.2 ot applicable 15.3 Applicable for full disconnection and microdisconnection 17 Endurance Compliance is checked on three separate appliances or switches For 17.2.4.4, the number of cycles declared according to 7.1.4 is 10 000, unless otherwise specified in 24.1.3 of the relevant part 2 of IEC 60335...: Switches for operation under no load and which can be operated only by a tool, and switches operated by hand that are interlocked so that they cannot be operated under load, are not subjected to the tests However, switches without this interlock are subjected to the test of 17.2.4.4 for 100 cycles of operation Subclauses 17.2.2 and 17.2.5.2 not applicable The ambient temperature during the test is that occurring in the appliance during the test of Clause 11 in IEC 60335-1 The temperature rise of the terminals not more than 30 K above the temperature rise measured in clause 11 of IEC 60335-1 (K)...: TRF o. IEC60335_2_80E
age 64 of 114 Report o.: STUESO017022702211HS 20 Clearances, creepage distances, solid insulation and coatings of rigid printed board assemblies This clause is applicable to clearances and creepage distances for functional insulation, across full disconnection and micro-disconnection, as stated in table 24 I AEX I (ORMATIVE) MOTORS HAVIG BASIC ISULATIO THAT IS IADEQUATE FOR THE RATED VOLTAGE OF THE ALIACE The following modifications to this standard are applicable for motors having basic insulation that is inadequate for the rated voltage of the appliance: 8 rotection against access to live parts 8.1 Metal parts of the motor are considered to be bare live parts 11 Heating 11.3 The temperature rise of the body of the motor is determined instead of the temperature rise of the windings 11.8 The temperature rise of the body of the motor, where in contact with insulating material, not exceeding values in table 3 for the relevant insulating material 16 Leakage current and electric strength 16.3 Insulation between live parts of the motor and its other metal parts is not subjected to the test 19 Abnormal operation 19.1 The tests of 19.7 to 19.9 are not carried out 19.I.101 Appliance operated at rated voltage with each of the following fault conditions: - short circuit of the terminals of the motor, including any capacitor incorporated in the motor circuit - short circuit of each diode of the rectifier - open circuit of the supply to the motor - open circuit of any parallel resistor, the motor being in operation Only one fault simulated at a time, the tests carried out consecutively 22 Construction TRF o. IEC60335_2_80E
age 65 of 114 Report o.: STUESO017022702211HS 22.I.101 J For class I appliances incorporating a motor supplied by a rectifier circuit, the d.c. circuit being insulated from accessible parts of the appliance by double or reinforced insulation Compliance checked by the tests specified for double and reinforced insulation AEX J (ORMATIVE) COATED RITED CIRCUIT BOARDS Testing of protective coatings of printed circuit boards carried out in accordance with IEC 60664-3 with the following modifications: 5.7 Conditioning of the test specimens When production samples are used, three samples of the printed circuit board are tested 5.7.1 Cold The test is carried out at -25 C 5.7.3 Rapid change of temperature Severity 1 is specified 5.9 Additional tests K This subclause is not applicable AEX K (ORMATIVE) OVERVOLTAGE CATEGORIES The information on overvoltage categories is extracted from IEC 60664-1 Overvoltage category is a numeral defining a transient overvoltage condition Equipment of overvoltage category IV is for use at the origin of the installation Equipment of overvoltage category III is equipment in fixed installations and for cases where the reliability and the availability of the equipment is subject to special requirements Equipment of overvoltage category II is energy consuming equipment to be supplied from the fixed installation If such equipment is subjected to special requirements with regard to reliability and availability, overvoltage category III applies TRF o. IEC60335_2_80E
age 66 of 114 Report o.: STUESO017022702211HS L M Equipment of overvoltage category I is equipment for connection to circuits in which measures are taken to limit transient overvoltages to an appropriate low level AEX L (IFORMATIVE) GUIDACE FOR THE MEASUREMET OF CLEARACES AD CREEAGE DISTACES Information for the determination of clearances and creepage distances AEX M (ORMATIVE) OLLUTIO DEGREE The information on pollution degrees is extracted from IEC 60664-1 ollution The microenvironment determines the effect of pollution on the insulation, taking into account the macroenvironment Means may be provided to reduce pollution at the insulation by effective enclosures or similar Minimum clearances specified where pollution may be present in the microenvironment Degrees of pollution in the microenvironment For evaluating creepage distances, the following degrees of pollution in the microenvironment are established: - pollution degree 1: no pollution or only dry, nonconductive pollution occurs. The pollution has no influence - pollution degree 2: only non-conductive pollution occurs, except that occasionally a temporary conductivity caused by condensation is to be expected - pollution degree 3: conductive pollution occurs or dry non-conductive pollution occurs that becomes conductive due to condensation that is to be expected - pollution degree 4: the pollution generates persistent conductivity caused by conductive dust or by rain or snow AEX (ORMATIVE) ROOF TRACKIG TEST TRF o. IEC60335_2_80E
age 67 of 114 Report o.: STUESO017022702211HS The proof tracking test is carried out in accordance with IEC 60112 with the following modifications: 7 Test apparatus 7.3 Test solutions Test solution A is used 10 Determination of proof tracking index (TI) 10.1 rocedure The proof voltage is 100V, 175V, 400V or 600V...: 175V The test is carried out on five specimens In case of doubt, additional test with proof voltage reduced by 25V, the number of drops increased to 100 10.2 Report O The report states if the TI value was based on a test using 100 drops with a test voltage of (TI-25) V AEX O (IFORMATIVE) SELECTIO AD SEQUECE OF THE TESTS OF CLAUSE 30 Description of tests for determination of resistance to heat and fire AEX (IFORMATIVE) GUIDACE FOR THE ALICATIO OF THIS STADARD TO ALIACES USED I WARM DAM EQUABLE CLIMATES Modifications applicable for class 0 and 01 appliances having a rated voltage exceeding 150V, intended to be used in countries having a warm damp equable climate and that are marked WDaE Modifications may also be applied to class 1 appliances having a rated voltage exceeding 150V, intended to be used in countries having a warm damp equable climate and that are marked WdaE, if liable to be connected to a supply mains that excludes the protective earthing conductor 5.7 The ambient temperature for the tests of clauses 11 and 13 is 40 +3/0 C 7.1 The appliance marked with the letters WDaE 7.12 The instructions state that the appliance is to be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30 ma TRF o. IEC60335_2_80E
age 68 of 114 Report o.: STUESO017022702211HS The instructions state that the appliance is considered to be suitable for use in countries having a warm damp equable climate, but may also be used in other countries 11.8 The values of Table 3 are reduced by 15 K 13.2 The leakage current for class I appliances not exceeding 0,5 ma 15.3 The value of t is 37 C 16.2 The leakage current for class I appliances not exceeding 0,5 ma (ma): 19.13 The leakage current test of 16.2 is applied in addition to the electric strength test of 16.3 Q R AEX Q (IFORMATIVE) SEQUECE OF TESTS FOR THE EVALUATIO OF ELECTROIC CIRCUITS Description of tests for appliances incorporating electronic circuits AEX R (ORMATIVE) SOFTWARE EVALUATIO rogrammable electronic circuits requiring software incorporating measures to control the fault/error conditions specified in table R.1 or R.2 validated in accordance with the requirements of this annex R.1 rogrammable electronic circuits using software rogrammable electronic circuits requiring software incorporating measures to control the fault/error conditions specified in table R.1 or R.2 constructed so that the software does not impair compliance with the requirements of this standard R.2 Requirements for the architecture R.2.1.1 rogrammable electronic circuits requiring software incorporating measures to control the fault/error conditions specified in table R.1 or R.2 use measures to control and avoid software-related faults/errors in safety-related data and safetyrelated segments of the software rogrammable electronic circuits requiring software incorporating measures to control the fault/error conditions specified in table R.2 have one of the following structures: - single channel with periodic self-test and monitoring - dual channel (homogenous) with comparison - dual channel (diverse) with comparison TRF o. IEC60335_2_80E
age 69 of 114 Report o.: STUESO017022702211HS rogrammable electronic circuits requiring software incorporating measures to control the fault/error conditions specified in table R.1 have one of the following structures: - single channel with functional test - single channel with periodic self-test - dual channel without comparison R.2.2 Measures to control faults/errors R.2.2.1 R.2.2.2 R.2.2.3 R.2.2.4 R.2.2.5 R.2.2.6 When redundant memory with comparison is provided on two areas of the same component, the data in one area is stored in a different format from that in the other area rogrammable electronic circuits with functions requiring software incorporating measures to control the fault/error conditions specified in table R.2 and that use dual channel structures with comparison, have additional fault/error detection means for any fault/errors not detected by the comparison For programmable electronic circuits with functions requiring software incorporating measures to control the fault/error conditions specified in table R.1 or R.2, means are provided for the recognition and control of errors in transmissions to external safety-related data paths For programmable electronic circuits with functions requiring software incorporating measures to control the fault/error conditions specified in table R.1 or R.2, the programmable electronic circuits incorporate measures to address the fault/errors in safety-related segments and data indicated in table R.1 and R.2 as appropriate For programmable electronic circuits with functions requiring software incorporating measures to control the fault/error conditions specified in table R.1 or R.2, detection of a fault/error occur before compliance with clause 19 is impaired The software is referenced to relevant parts of the operating sequence and the associated hardware functions R.2.2.7 Labels used for memory locations are unique R.2.2.8 The software is protected from user alteration of safety-related segments and data TRF o. IEC60335_2_80E
age 70 of 114 Report o.: STUESO017022702211HS R.2.2.9 Software and safety-related hardware under its control is initialized and terminates before compliance with clause 19 is impaired R.3 Measures to avoid errors R.3.1 General For programmable electronic circuits with functions requiring software incorporating measures to control the fault/error conditions specified in table R.1 or R.2, the following measures to avoid systematic fault in the software are applied Software that incorporates measures used to control the fault/error conditions specified in table R.2 is inherently acceptable for software required to control the fault/error conditions specified in table R.1 R.3.2 Specification R.3.2.1 Software safety requirements: Software Id: The specification of the software safety requirements includes the descriptions listed R.3.2.2 Software architecture R.3.2.2.1 The specification of the software architecture includes the aspects listed Document ref. o: - techniques and measures to control software faults/errors (refer to R.2.2); - interactions between hardware and software; - partitioning into modules and their allocation to the specified safety functions; - hierarchy and call structure of the modules (control flow); - interrupt handling; - data flow and restrictions on data access; - architecture and storage of data; - time-based dependencies of sequences and data R.3.2.2.2 The architecture specification is validated against the specification of the software safety requirements by static analysis R.3.2.3 Module design and coding R.3.2.3.1 Based on the architecture design, software is suitably refined into modules Software module design and coding is implemented in a way that is traceable to the software architecture and requirements TRF o. IEC60335_2_80E
age 71 of 114 Report o.: STUESO017022702211HS R.3.2.3.2 Software code is structured R.3.2.3.3 Coded software is validated against the module specification by static analysis The module specification is validated against the architecture specification by static analysis R.3.3.3 Software validation The software is validated with reference to the requirements of the software safety requirements specification Compliance is checked by simulation of: - input signals present during normal operation - anticipated occurrences - undesired conditions requiring system action TABLE R.1 GEERAL FAULT/ERROR CODITIOS Component 1) Fault/error Acceptable measures 2) 3) Definitions Document reference for applied measure Document reference for applied test Verdict 1 CU 1.1 Registers Stuck at Functional test, or periodic self-test using either: - static memory test, or - word protection with single bit redundancy H.2.16.5 H.2.16.6 H.2.19.6 H.2.19.8.2 1.2 VOID 1.3 rogramme counter Stuck at Functional test, or eriodic self-test, or Independent time-slot monitoring, or H.2.16.5 H.2.16.6 H.2.18.10. 4 Logical monitoring of the programme sequence H.2.18.10. 2 2 Interrupt handling and execution o interrupt or too frequent interrupt Functional test, or time-slot monitoring H.2.16.5 H.2.18.10. 4 TRF o. IEC60335_2_80E
age 72 of 114 Report o.: STUESO017022702211HS 3 Clock Wrong frequency (for quartz synchronize d clock: harmonics/ subharmonics only) Frequency monitoring, or time slot monitoring H.2.18.10. 1 H.2.18.10. 4 4. Memory 4.1 Invariable memory All single bit faults eriodic modified checksum, or multiple checksum, or word protection with single bit redundancy H.2.19.3.1 H.2.19.3.2 H.2.19.8.2 4.2 Variable memory DC fault eriodic static memory test, or word protection with single bit redundancy H.2.19.6 H.2.19.8.2 4.3 Addressing (relevant to variable and invariable memory) Stuck at Word protection with single bit redundancy including the address H.2.19.8.2 5 Internal data path Stuck at DC fault Word protection with single bit redundancy Comparison of redundant CUs by either: H.2.19.8.2 - reciprocal comparison H.2.18.15 - independent hardware comparator H.2.18.3 5.1 VOID 5.2 Addressing Wrong address Word protection with single bit redundancy including the address H.2.19.8.2 6 External communicat ion Hamming distance 3 Word protection with multi-bit redundancy, or CRC single work, or Transfer redundancy, or H.2.19.8.1 H.2.19.4.1 H.2.18.2.2 rotocol test H.2.18.14 6.1 VOID TRF o. IEC60335_2_80E
age 73 of 114 Report o.: STUESO017022702211HS 6.2 VOID 6.3 Wrong point Timing in time 7 Input/output periphery Wrong sequence Fault conditions specified in 19.11.2 Time-slot monitoring, or scheduled transmission Time-slot and logical monitoring, or Comparison of redundant communication channels by either: - reciprocal comparison - independent hardware comparator Logical monitoring, or time-slot monitoring, or Scheduled transmission (same options as for wrong point in time) lausibility check Comparison of redundant communication channels by either: - reciprocal comparison - independent hardware comparator H.2.18.10. 4 H.2.18.18 H.2.18.10. 3 H.2.18.15 H.2.18.3 H.2.18.10. 2 H.2.18.10. 4 H.2.18.18 H.2.18.13 H.2.18.15 H.2.18.3 7.1 VOID 7.2 Analog I/O 7.2.1 A/D and D/Aconverter 7.2.2 Analog multiplexer Fault conditions specified in 19.11.2 Wrong addressing lausibility check H.2.18.13 lausibility check H.2.18.13 8 VOID 9 Custom chips 4) e.g. ASIC, GAL, Gate array Any output outside the static and dynamic functional specification eriodic self-test H.2.16.6 OTE A Stuck-at fault model denotes a fault model representing an open circuit or a non-varying signal level. A DC fault model denotes a stuck-at fault model incorporating short circuit between signal lines. TRF o. IEC60335_2_80E
age 74 of 114 Report o.: STUESO017022702211HS 1) For fault/error assessment, some components are divided into their sub-functions. 2) For each sub-function in the table, the Table R.2 measure will cover the software fault/error. 3) Where more than one measure is given for a sub-function, these are alternatives. 4) To be divided as necessary by the manufacturer into sub-functions. TRF o. IEC60335_2_80E
age 75 of 114 Report o.: STUESO017022702211HS 10.1 TABLE: ower input deviation Input deviation of/at: rated (W) measured (W) d (W, %) Required d (W, %) Remark 230V / 50Hz 350 375,7 7,3% +15% FM-1220T/Y 230V / 50Hz 350 364,5 4,1% +15% 1) FM-1220T/Y 230V / 50Hz 300 312,4 4,1% +15% FM-1218T/Y 230V / 50Hz 230 234,7 2,0% +15% FM-1215T/Y 230V / 50Hz 200 204,5 2,2% +15% FM-1212T/Y 230V / 50Hz 180 191,5 6,3% +15% FM-1210T/Y 230V / 50Hz 160 166,7 4,4% +20% FM-1209T/Y 230V / 50Hz 140 142,3 1,6% +20% FM-1206T/Y Supplementary information: 1) Appliance using 12µf capacitor. 10.2 TABLE: Current deviation Current deviation of/at: I rated (A) I measured (A) di (A, %) Required di (A, %) Remark Supplementary information: 11.8-1 TABLE: Heating test, thermocouple measurements (For model FM-1220T/Y) Test voltage (V)... : 240V x 1,06=254,4V Ambient ( C)... : T1: 19,5 C, T2: 21,1 C Thermocouple locations Max. temperature rise measured, dt (K) Max.temperature rise limit, dt (K) Supply cord 16,6 50 Internal wire to motor (T105) 18,0 T105-25=80 Internal to CB (T105) 14,1 T105-25=80 Motor winding (Class120 ) 77,8 80 Motor capacitor (T70) 12,7 T70-25=45 Relay RL1 (T85) 10,3 T85-25=60 Relay RL3 (T85) 6,5 T85-25=60 Main CB 5,4 120 lastic enclosure support main CB 5,9 For cl.30.1 Transformer input winding(dazhong EI35)(Class 105) 10,2 65 Transformer output winding(dazhong 8,9 65 TRF o. IEC60335_2_80E
EI35) (Class 105) Transformer input winding(qiagli EI35)(Class 105) Transformer output winding(qiagli EI35) (Class 105) age 76 of 114 Report o.: STUESO017022702211HS 10,5 65 8,7 65 Varistor (T85) 7,4 T85-25=60 X2-capacitor 6,9 T105-25=80 Control CB 2,9 120 CB box 2,5 For cl.30.1 Control panel 1,2 75 Metal enclosure 1,5 60 Test corner 0,3 65 Supplementary information: 11.8-1 TABLE: Heating test, resistance method (For model FM-1220T/Y) Test voltage (V)... : 240V x 1,06=254,4V Ambient, t1 ( C)... : 19,5 Ambient, t2 ( C)... : 20,1 Temperature rise of winding R1 (Ω) R2 (Ω) dt (K) Max. dt (K) Insulation class Winding of motor 23,6 31,5 84,9 90 Class 120 Transformer input winding(dazhong EI35) Transformer output winding(dazhong EI35) Transformer input winding(qiagli EI35) Transformer output winding(qiagli EI35) Supplementary information: 3,54 3,95 28,8 75 Class 105 0,33 0,36 22,49 75 Class 105 3,6 3,98 26,2 75 Class 105 0,3 0,329 23,9 75 Class 105 11.8-2 TABLE: Heating test, thermocouple measurements (For model FM-1209T/Y) Thermocouple locations Test voltage (V)... : 240V x 1,06=254,4V Ambient ( C)... : T1: 19,3 C, T2: 20,1 C Max. temperature rise measured, dt (K) Max.temperature rise limit, dt (K) Supply cord 15,2 50 Internal wire to motor (T105) 16,3 T105-25=80 TRF o. IEC60335_2_80E
age 77 of 114 Report o.: STUESO017022702211HS Internal to CB (T105) 13,5 T105-25=80 Motor winding (Class120 ) 76,9 80 Motor capacitor (T70) 11,9 T70-25=45 Relay RL1 (T85) 9,8 T85-25=60 Relay RL3 (T85) 6,7 T85-25=60 Main CB 6,7 120 lastic enclosure support main CB 5,9 For cl.30.1 Transformer input winding(dazhong EI35)(Class 105) Transformer output winding(dazhong EI35) (Class 105) Transformer input winding(qiagli EI35)(Class 105) Transformer output winding(qiagli EI35) (Class 105) 10,7 65 11,1 65 10,5 65 11,3 65 Varistor (T85) 6,9 T85-25=60 X2-capacitor 6,8 T105-25=80 Control CB 2,9 120 CB box 2,4 For cl.30.1 Control panel 1,1 75 Metal enclosure 1,5 60 Test corner 0,2 65 Supplementary information: 11.8-2 TABLE: Heating test, resistance method (For model FM-1209T/Y) Test voltage (V)... : 240V x 1,06=254,4V Ambient, t1 ( C)... : 19,3 Ambient, t2 ( C)... : 20,1 Temperature rise of winding R1 (Ω) R2 (Ω) dt (K) Max. dt (K) Insulation class Winding of motor 80 106 82,5 90 Class 120 Transformer input winding(dazhong EI35) Transformer output winding(dazhong EI35) Transformer input winding(qiagli EI35) Transformer output winding(qiagli EI35) 3,54 3,94 28,1 75 Class 105 0,33 0,37 30,1 75 Class 105 3,6 3,92 22,9 75 Class 105 0,3 0,328 23,1 75 Class 105 TRF o. IEC60335_2_80E
Supplementary information: age 78 of 114 Report o.: STUESO017022702211HS 11.8-3 TABLE: Heating test, thermocouple measurements (For model FM-1220T/Y using 12µf capacitor.) Thermocouple locations Test voltage (V)... : 240V x 1,06=254,4V Ambient ( C)... : T1: 19,5 C, T2: 21,1 C Max. temperature rise measured, dt (K) Max.temperature rise limit, dt (K) Supply cord 16,3 50 Internal wire to motor (T105) 18,2 T105-25=80 Internal to CB (T105) 13,8 T105-25=80 Motor winding (Class120 ) 77,1 80 Motor capacitor (T70) 12,0 T70-25=45 Relay RL1 (T85) 10,2 T85-25=60 Relay RL3 (T85) 6,8 T85-25=60 Main CB 5,2 120 lastic enclosure support main CB 5,6 For cl.30.1 Transformer input winding(dazhong EI35)(Class 105) Transformer output winding(dazhong EI35) (Class 105) Transformer input winding(qiagli EI35)(Class 105) Transformer output winding(qiagli EI35) (Class 105) 10,4 65 8,3 65 10,1 65 8,2 65 Varistor (T85) 7,3 T85-25=60 X2-capacitor 6,7 T105-25=80 Control CB 2,7 120 CB box 2,4 For cl.30.1 Control panel 1,2 75 Metal enclosure 1,4 60 Test corner 0,3 65 Supplementary information: 11.8-3 TABLE: Heating test, resistance method (For model FM-1220T/Y using 12µf capacitor.) Test voltage (V)... : 240V x 1,06=254,4V Ambient, t1 ( C)... : 19,5 TRF o. IEC60335_2_80E
age 79 of 114 Report o.: STUESO017022702211HS Ambient, t2 ( C)... : 20,1 Temperature rise of winding R1 (Ω) R2 (Ω) dt (K) Max. dt (K) Insulation class Winding of motor 23,6 31,9 87,7 90 Class 120 Transformer input winding(dazhong EI35) Transformer output winding(dazhong EI35) Transformer input winding(qiagli EI35) Transformer output winding(qiagli EI35) Supplementary information: 3,54 3,81 17,8 75 Class 105 0,33 0,35 13,8 75 Class 105 3,6 3,89 18,9 75 Class 105 0,3 0,32 15,3 75 Class 105 13.2 TABLE: Leakage current Heating appliances: 1,15 x rated input (W)...: --- Motor-operated and combined appliances: 1,06 x rated voltage (V)...: 240V x 1,06=254,4V Leakage current between I (ma) Max. allowed I (ma) B/w Live part and metal part (For model FM-1220T/Y) 0,07 0.75 B/w Live part and knob (For model FM-1220T/Y) 0,01 peak 0.35mA peak B/w Live part and metal part (For model FM-1209T/Y) 0,07 0.75 B/w Live part and knob (For model FM-1209T/Y) 0,01 peak 0.35mA peak Supplementary information: 13.3 TABLE: Electric strength Test voltage applied between: Voltage (V) Breakdown (Yes/o) B/w Live part and metal part (For model FM-1220T/Y) 1000 o B/w Live part and knob (For model FM-1220T/Y) 3000 o B/w Live part and metal part (For model FM-1209T/Y) 1000 o B/w Live part and knob (For model FM-1209T/Y) 3000 o Supplementary information: 14 TABLE: Transient overvoltages Clearance between: Cl (mm) Required Cl (mm) Rated impulse voltage (V) Impulse test voltage (V) Flashover (Yes/o) TRF o. IEC60335_2_80E
Supplementary information: age 80 of 114 Report o.: STUESO017022702211HS 16.2 TABLE: Leakage current Single phase appliances: 1.06 x rated voltage (V)... : Three phase appliances 1.06 x rated voltage divided by 3 (V)... : 240V x 1,06=254,4V --- Leakage current between I (ma) Max. allowed I (ma) B/w Live part and metal part (For model FM-1220T/Y) 0,08 0,75 B/w Live part and knob (For model FM-1220T/Y) 0,01 0,25 B/w Live part and metal part (For model FM-1209T/Y) 0,08 0,75 B/w Live part and knob (For model FM-1209T/Y) 0,01 0,25 Supplementary information: 16.3 TABLE: Electric strength Test voltage applied between: Voltage (V) Breakdown (Yes/o) B/w Live part and metal part (For model FM-1220T/Y) 1000 o B/w Live part and knob (For model FM-1220T/Y) 3000 o B/w Live part and metal part (For model FM-1209T/Y) 1000 o B/w Live part and knob (For model FM-1209T/Y) 3000 o Supplementary information: 17 TABLE: Overload protection, temperature rise Temperature rise of part/at: T ( C) Max. T ( C) Transformer input winding(dazhong EI35) 111,3 150 Transformer output winding(dazhong EI35) 110,4 150 Transformer input winding(qiagli EI35) 123,1 150 Transformer output winding(qiagli EI35) 119,8 150 SELV wire 20,5 95 Supplementary information: The thermal link operated. 19 Abnormal operation conditions Operational characteristics YES/O Operational conditions Are there electronic circuits to control the appliance operation? Are there off or stand-by position? Yes Yes TRF o. IEC60335_2_80E
The unintended operation of the appliance results in dangerous malfunction? age 81 of 114 Report o.: STUESO017022702211HS o Sub-clause Operating conditions description Test results description EC description EM 19.11.4 Software type required 19.11.3 EC Final result 19.2.A.A.A.A.A.A.A 19.3.A.A.A.A.A.A.A 19.4.A.A.A.A.A.A.A 19.5.A.A.A.A.A.A.A 19.6.A.A.A.A.A.A.A 19.7 Work in 240, lock the motor and capacitor opencircuited 19.7 Work in 240V, lock the motor and capacitor shortcircuited 19.7 Work in 240V, lock the motor Internal protect, temperature of the windings not exceed the relevant value Internal protect, temperature of the windings not exceed the relevant value Internal protect, temperature of the windings not exceed the relevant value.a.a.a.a.a.a.a.a.a 19.8.A.A.A.A.A.A.A 19.10.A.A.A.A.A.A.A 19.11.2 Input: 240V o hazard.a.a.a 19.11.4.8.A.A.A.A.A.A.A 19.10X.A.A.A.A.A.A.A Supplementary information: 19.7 TABLE: Abnormal operation, locked rotor/moving parts (For model FM- 1220T/Y) Test voltage (V)... : 240V TRF o. IEC60335_2_80E
age 82 of 114 Report o.: STUESO017022702211HS Ambient, t1 ( C)... : 21,0 Ambient, t2 ( C)... : 20,8 Temperature of winding R1 (Ω) R2 (Ω) T (K) T ( C) Max. T ( C) Winding of motor (locked rotor) Winding of motor (locked rotor and O-C capacitor) Winding of motor (locked rotor and S-C capacitor) 23,6 34,8 121,0 122 215 23,6 34,6 115,8 117 215 23,6 35,1 122,6 122,8 215 Supplementary information: 19.7 TABLE: Abnormal operation, locked rotor/moving parts (For model FM- 1209T/Y) Test voltage (V)...: 240V Ambient, t1 ( C)...: 21,3 Ambient, t2 ( C)...: 21,1 Temperature of winding R1 (Ω) R2 (Ω) T (K) T ( C) Max. T ( C) Winding of motor (locked rotor) Winding of motor (locked rotor and O-C capacitor) Winding of motor (locked rotor and S-C capacitor) 80 118 121,7 123 215 80 116 114,9 119 215 80 119 122,8 124 215 Supplementary information: 19.7 TABLE: Abnormal operation, locked rotor/moving parts (For model FM-1220T/Y using 12µf capacitor.) Test voltage (V)... : 240V Ambient, t1 ( C)... : 21,3 Ambient, t2 ( C)... : 20,9 Temperature of winding R1 (Ω) R2 (Ω) T (K) T ( C) Max. T ( C) Winding of motor (locked rotor) Winding of motor (locked rotor and O-C capacitor) Winding of motor (locked rotor and S-C capacitor) 23,6 34,4 117,5 138,8 215 23,6 34,3 116,4 137,7 215 23,6 34,8 121,8 144,1 215 Supplementary information: TRF o. IEC60335_2_80E
age 83 of 114 Report o.: STUESO017022702211HS 19.13 TABLE: Abnormal operation, temperature rises Thermocouple locations Max. temperature rise measured, dt (K) Max.temperature rise limit, dt (K) --- FM-1220T/Y FM-1209T/Y --- --- Test 1 Test 2 --- --- 1 2 3 4 5 6 --- Supply cord 26,9 26,2 27,9 26,6 26,0 27,6 For Ref. Knob 2,9 3,2 4,1 2,6 3,0 3,8 For cl.30.1 Test corner 0,8 1,3 1,9 0,5 1,1 1,6 For Ref. Supplementary information: Test 1: 1. locked rotor 2. locked rotor and O-C capacitor 3. locked rotor and S-C capacitor Test 2: 4. locked rotor 5. locked rotor and O-C capacitor 6. locked rotor and S-C capacitor 19.13 TABLE: Abnormal operation, temperature rises Thermocouple locations Max. temperature rise measured, dt (K) Max.temperature rise limit, dt (K) --- For model FM-1220T/Y using 12µf capacitor. --- --- 1 2 3 --- Supply cord 25,3 25,1 25,5 For Ref. Knob 2,7 2,9 2,8 For cl.30.1 Test corner 1,1 1,2 1,5 For Ref. Supplementary information: 1. locked rotor 2. locked rotor and O-C capacitor 3. locked rotor and S-C capacitor TRF o. IEC60335_2_80E
age 84 of 114 Report o.: STUESO017022702211HS 24.1 TABLE: Components information Object / part o. Manufacturer/ trademark Type / model Technical data Standard Mark(s) of conformity 1 ) Supply cord SHUDE LUJIAO KAITE WIRE H05VV-F 3G, 0,75 mm 2, 300/500V E 60227 IEC 53 VDE 40004728 Supply cord for china Shunde Beijiao Shunjing Metal Electrical Factory 60227 IE(53(RVV) 3G, 0,75 mm 2, 300/500V E 60227 IEC 53 CCC 2002010105 006524 Internal wire Zhong Shan Yong Roi Electric Factory Co., Ltd 1015 18/24AWG, 105ºC E 60335-1 E 60335-2-80 Tested with appliance UL E204893 Internal wire (Alt.) ZHOGSHA WEIFEG ELECTRICAL EQUIMET CO LTD 1015 18AWG, T105, 600V E 60335-1 E 60335-2-80 Tested with appliance UL E314135 Internal wire ZHOGSHA JIZHOG ELECTROIC CO LTD 2468 26AWG, T80, 300V E 60335-1 E 60335-2-80 Tested with appliance UL E337898 Internal wire (Alt.) ZHOGSHA ATOU BOYU WIRE MR 2468 VW-1, 300V, 26AWG, T80 E 60335-1 E 60335-2-80 Tested with appliance UL E257280 Internal wire (Alt.) GUAGDOG YOG ROI CABLE TECHOLOGY CO LTD 2468 26AWG, 300V, T80 E 60335-1 E 60335-2-80 Tested with appliance UL E204893 Varistor Thinking Electronic Industrial Co., Ltd. TVR14561 Max. continuous voltage: 350V, T85 E 61051 E 61051-2 E 61051-2-2 VDE 005944 Varistor (Alt.) Huizhou Songlongxindian Electronics Technology Co.,Ltd. 10D561K Max. continuous voltage: 350V, T85 E 61051 E 61051-2 E 61051-2-2 VDE 40040037 Varistor (Alt.) Fenghua Adv.Tech.(Holding ) Co.Ltd FR-10K561 Max. continuous voltage: 350V, T85 E 61051 E 61051-2 E 61051-2-2 VDE 40008242 TRF o. IEC60335_2_80E
Varistor (Alt.) Huizhou Songlongxindian Electronics Technology Co.Ltd age 85 of 114 Report o.: STUESO017022702211HS 14D561K Max. continuous E 61051 VDE voltage: 350V, T85 E 61051-2 40040037 E 61051-2-2 X2 capacitor Foshan Shunde Chuang Ge Electronic Industrial Co., Ltd. MK-X2 0,22uF, 40/105/21 C E 60384-14 VDE 40008922 X2 capacitor (Alt.) Guangdong Fengming Electronic Tech.Co.,Ltd MK-X2 0,22uF 275VAC T105 E 60384-14 VDE 40025702 X2 capacitor (Alt.) Dain Electronic Co.,Ltd MX X2 0,22uF 275VAC T110 E 60384-14 VDE 40018798 Relay ingbo Tianbo Ganglian Electronics Co., Ltd. HJR-3FF-S-H 10A, 240VAC; 12A, 120VAC; 15A, 12VDC contact: 12VDC E 60335-1 E 61810-1 VDE 40005471 10000 cycle,t85 Transformer Da Zhong Electrinic Co., Ltd EI35-100250 Input: 220V~, 50Hz Output: 10V~, 250mA, Class105(A) E 60335-1 E 60335-2-80 Tested with appliance Transformer Foshan Shunde Qiangli Electrical Co., Ltd EI35 Input: 220V~, 50Hz Output: 10V~, 250Ma, Class105(A) E 60335-1 E 60335-2-80 Tested with appliance CB Kingboard Laminates (Macao Commercial Offshore) Ltd. KB-6160 V-0, Thickness:0,8mm E 60335-1 E 60335-2-80 Tested with appliance UL E123995 CB (Alt.) GUAGDOG CHEGDE ELECTROIC TECHOLOGY CO LTD D1 V-0, Thickness:1,6mm E 60335-1 E 60335-2-80 Test with appliance UL E322995 CB (Alt.) GUAGZHOU TIMESQUICK ELECTROIC CO LTD SD-V0 V-0, Thickness:1,6mm E 60335-1 E 60335-2-80 Test with appliance UL E315225 CB (Alt.) Kingboard Laminates holdings ltd KB-3151C V-0, Thickness:1,6mm E 60335-1 E 60335-2-80 Test with appliance UL E123995 lastic enclosure IGBO LG YOGXIG FR-500 ABS, V-0 E 60335-1; E 60335-2-80 Tested with appliance UL E203955 TRF o. IEC60335_2_80E
Thermal link of transformer Xiamen Set Electronics Co. Ltd. age 86 of 114 Report o.: STUESO017022702211HS F3 250V~, 1A, tf125 E 60691 VDE 40004041 End-closed connector HEAVY OWER CO LTD CE2 300V, T150 E 60335-1 E 60335-2-80 Tested with appliance UL E113650 Running capacitor for model FM- 1206T/Y, FM- 1209T/Y Xunde Electrical & Electronic Co., Ltd. CBB61 AC450V, 50/60Hz, 5uF±5%, T70 DI E 60252-1 VDE 40011209 Running capacitor for model FM- 1206T/Y, FM- 1209T/Y (Alt.) Sheng Ye Electrical Co.,Ltd C61-2-32 450V.AC, 50/60Hz, T85, 2, 5uF±5% E 60252-1 TÜV B 1510732040 19 Running capacitor for model FM- 1206T/Y, FM- 1209T/Y (Alt.) Sheng Ye Electrical Co.,Ltd CBB61 450V.AC, 50/60Hz, T85, 5uF±5% E 60252-1 VDE 101392 Running capacitor for model FM- 1210T/Y, FM- 1212T/Y Xunde Electrical & Electronic Co., Ltd. CBB61 AC450V, 50/60Hz, 6uF±5%, T85 DI E 60252-1 VDE 40030442 Running capacitor for model FM- 1210T/Y,FM- 1212T/Y (Alt.) Sheng Ye Electrical Co.,Ltd C61-2-32 450V.AC, 50/60Hz, T85, 2, 6uF±5% E 60252-1 TÜV B 1510732040 19 Running capacitor for model FM- 1210T/Y,FM- 1212T/Y (Alt.) Sheng Ye Electrical Co.,Ltd CBB61 450V.AC, 50/60Hz, T85, 6uF±5% E 60252-1 VDE 101392 Running capacitor for model FM- 1215T/Y, FM- 1218T/Y Xunde Electrical & Electronic Co., Ltd. CBB61 AC450V, 50/60Hz, 8uF±5%, T85 DI E 60252-1 VDE 40030442 Running capacitor for model FM- 1215T/Y,FM- 1218T/Y (Alt.) Sheng Ye Electrical Co.,Ltd C61-2-32 450V.AC, 50/60Hz, T85, 2, 8uF±5% E 60252-1 TÜV B 1510732040 19 TRF o. IEC60335_2_80E
Running capacitor for model FM- 1215T/Y,FM- 1218T/Y (Alt.) Sheng Ye Electrical Co.,Ltd age 87 of 114 Report o.: STUESO017022702211HS CBB61 450V.AC, 50/60Hz, E 60252-1 VDE T85, 8uF±5% 101392 Running capacitor for model FM- 1220T/Y Xunde Electrical & Electronic Co., Ltd. CBB60 AC450V, 50/60Hz, 10uF±5%, T70 DI E 60252-1 VDE 40008522 Running capacitor for model FM- 1220T/Y (Alt.) Xunde Electrical & Electronic Co., Ltd. CBB60 450V.AC, 50/60Hz, 12uF±5%, T70 DI E60252-1 VDE 40008522 Running capacitor for model FM- 1220T/Y (Alt.) Xunde Electrical & Electronic Co., Ltd. CBB61 450V.AC, 50/60Hz, 12uF±5%, T85 DI E60252-1 VDE 40030442 Running capacitor for model FM- 1220T/Y (Alt.) Sheng Ye Electrical Co.,Ltd C61-2-32 450V.AC, 50/60Hz, T85, 2, 12uF E 60252-1 TÜV B 1510732040 19 Running capacitor for model FM- 1220T/Y (Alt.) Sheng Ye Electrical Co.,Ltd CBB60 450V.AC, 50/60Hz, T85, 12uF±5% E 60252-1 VDE 40004648 Running capacitor for model FM- 1220T/Y (Alt.) Sheng Ye Electrical Co.,Ltd CBB60 450V.AC, 50/60Hz, T85, 12uF±5% E 60252-1 VDE 40024774 Thermal cut-out in motor Chang Zhou City Tong Li Electronic Co. Ltd. KW-125 250V~, 6A, Cycles 3000, T125 E 60730 VDE 40004418 Motor for model FM-1206T/Y, FM-1209T/Y GUAGZHOU THEODOOR ELECTRICEQUI MET CO., LTD YSK110-4 MOTOR (1209) 220V-240~, 50Hz 0,6A, 60W, Class120 E 60335-1 E 60335-2-80 Tested with appliance Motor for model FM-1210T/Y, FM-1212T/Y GUAGZHOU THEODOOR ELECTRICEQUI MET CO., LTD YSK110-4 MOTOR (1212) 220V-240~, 50Hz 0,85A, 80W, Class120 E 60335-1 E 60335-2-80 Tested with appliance Motor for model FM-1215T/Y, GUAGZHOU THEODOOR ELECTRICEQUI MET CO., LTD YSK110-4 MOTOR (1215) 220V-240~, 50Hz 1,2A, 100W, Class120 E 60335-1 E 60335-2-80 Tested with appliance Motor for model FM-1218T/Y GUAGZHOU THEODOOR ELECTRICEQUI MET CO., LTD YSK110-4 MOTOR (1218) 220V-240~, 50Hz 1,4A, 120W, Class120 E 60335-1 E 60335-2-80 Tested with appliance TRF o. IEC60335_2_80E
Motor for model FM-1220T/Y GUAGZHOU THEODOOR ELECTRICEQUI MET CO., LTD age 88 of 114 Report o.: STUESO017022702211HS YSK110-4 220V-240~, 50Hz E 60335-1 Tested with MOTOR 1,6A, 150W, E 60335-2-80 appliance (1220) Class120 Supplementary information: 28.1 TABLE: Threaded part torque test Threaded part identification Diameter of thread (mm) Column number (I, II, or III) Applied torque (m) Screw fixed metal enclosure 4,01 II 1,2 Screw fixed earth 4,01 II 1,2 Supplementary information: TRF o. IEC60335_2_80E
age 89 of 114 Report o.: STUESO017022702211HS 29.1 TABLE: Clearances Overvoltage category...... : II Type of insulation: Rated impulse voltage (V): Min. cl (mm) Basic (mm) Supplementary (mm) Reinforced (mm) Functional (mm) Verdict / Remark 330 0,2* / 0,5 / 0,8** 500 0,2* / 0,5 / 0,8** 800 0,2* / 0,5 / 0,8** 1 500 0,5 / 0,8** / 1,0*** 2 500 1,5 / 2,0*** 5,2 Between live parts and earthing metal 2 500 1,5 / 2,0*** 4,5 Between internal wire and plastic enclosure 2 500 1,5 / 2,0*** 4,6 Between different potential of CB. 4 000 3,0 / 3,5*** 9,2 Between live part of and control panel surface 6 000 5,5 / 6,0*** 8 000 8,0 / 8,5*** 10 000 11,0 / 11,5*** Supplementary information: *) For tracks on printed circuit boards if pollution degree 1 and 2 **) For pollution degree 3 ***) If the construction is affected by wear, distortion, movement of the parts or during assembly TRF o. IEC60335_2_80E
age 90 of 114 Report o.: STUESO017022702211HS 29.2 TABLE: Creepage distances, basic, supplementary and reinforced insulation Working voltage (V) Creepage distance (mm) ollution degree 1 2 3 Type of insulation Material group Material group I II IIIa/IIIb I II IIIa/IIIb* ) B** ) S** ) R** ) Verdict 50 0,18 0,6 0,85 1,2 1,5 1,7 1,9 50 0,18 0,6 0,85 1,2 1,5 1,7 1,9 50 0,36 1,2 1,7 2,4 3,0 3,4 3,8 125 0,28 0,75 1,05 1,5 1,9 2,1 2,4 125 0,28 0,75 1,05 1,5 1,9 2,1 2,4 125 0,56 1,5 2,1 3,0 3,8 4,2 4,8 250 0,56 1,25 1,8 2,5 3,2 3,6 4,0 5,2 B1 250 0,56 1,25 1,8 2,5 3,2 3,6 4,0 4,5 S1 250 1,12 2,5 3,6 5,0 6,4 7,2 8,0 9,2 R1 400 1,0 2,0 2,8 4,0 5,0 5,6 6,3 400 2,0 4,0 5,6 8,0 10,0 11,2 12,6 500 1,3 2,5 3,6 5,0 6,3 7,1 8,0 500 1,3 2,5 3,6 5,0 6,3 7,1 8,0 500 2,6 5,0 7,2 10,0 12,6 14,2 16,0 630 and 800 1,8 3,2 4,5 6,3 8,0 9,0 10,0 630 and 800 1,8 3,2 4,5 6,3 8,0 9,0 10,0 630 and 800 3,6 6,4 9,0 12,6 16,0 18,0 20,0 800 and 1000 2,4 4,0 5,6 8,0 10,0 11,0 12,5 800 and 1000 2,4 4,0 5,6 8,0 10,0 11,0 12,5 800 and 1000 4,8 8,0 11,2 16,0 20,0 22,0 25,0 1000 and 1250 3,2 5,0 7,1 10,0 12,5 14,0 16,0 1000 and 1250 3,2 5,0 7,1 10,0 12,5 14,0 16,0 1000 and 1250 6,4 10,0 14,2 20,0 25,0 28,0 32,0 1250 and 1600 4,2 6,3 9,0 12,5 16,0 18,0 20,0 1250 and 1600 4,2 6,3 9,0 12,5 16,0 18,0 20,0 1250 and 1600 8,4 12,6 18,0 25,0 32,0 36,0 40,0 1600 and 2000 5,6 8,0 11,0 16,0 20,0 22,0 25,0 TRF o. IEC60335_2_80E
age 91 of 114 Report o.: STUESO017022702211HS 1600 and 2000 5,6 8,0 11,0 16,0 20,0 22,0 25,0 1600 and 2000 11,2 16,0 22,0 32,0 40,0 44,0 50,0 2000 and 2500 7,5 10,0 14,0 20,0 25,0 28,0 32,0 2000 and 2500 7,5 10,0 14,0 20,0 25,0 28,0 32,0 2000 and 2500 15,0 20,0 28,0 40,0 50,0 56,0 64,0 2500 and 3200 10,0 12,5 18,0 25,0 32,0 36,0 40,0 2500 and 3200 10,0 12,5 18,0 25,0 32,0 36,0 40,0 >2500 and 3200 20,0 25,0 36,0 50,0 64,0 72,0 80,0 3200 and 4000 12,5 16,0 22,0 32,0 40,0 45,0 50,0 3200 and 4000 12,5 16,0 22,0 32,0 40,0 45,0 50,0 3200 and 4000 25,0 32,0 44,0 64,0 80,0 90,0 100,0 4000 and 5000 16,0 20,0 28,0 40,0 50,0 56,0 63,0 4000 and 5000 16,0 20,0 28,0 40,0 50,0 56,0 63,0 4000 and 5000 32,0 40,0 56,0 80,0 100,0 112,0 126,0 5000 and 6300 20,0 25,0 36,0 50,0 63,0 71,0 80,0 5000 and 6300 20,0 25,0 36,0 50,0 63,0 71,0 80,0 5000 and 6300 40,0 50,0 72,0 100,0 126,0 142,0 160,0 6300 and 8000 25,0 32,0 45,0 63,0 80,0 90,0 100,0 6300 and 8000 25,0 32,0 45,0 63,0 80,0 90,0 100,0 6300 and 8000 50,0 64,0 90,0 126,0 160,0 180,0 200,0 8000 and 10000 32,0 40,0 56,0 80,0 100,0 110,0 125,0 8000 and 10000 32,0 40,0 56,0 80,0 100,0 110,0 125,0 8000 and 10000 64,0 80,0 112,0 160,0 200,0 220,0 250,0 10000 and 12500 40,0 50,0 71,0 100,0 125,0 140,0 160,0 10000 and 12500 40,0 50,0 71,0 100,0 125,0 140,0 160,0 10000 and 12500 80,0 100,0 142,0 200,0 250,0 280,0 320,0 Supplementary information: * ) Material group IIIb is allowed if the working voltage does not exceed 50 V ** ) B = Basic insulation, S = Supplementary insulation, R = Reinforced insulation B1: Between live parts and earthing metal S1: Between internal wire and plastic enclosure R1: Between live part of and control panel surface TRF o. IEC60335_2_80E
age 92 of 114 Report o.: STUESO017022702211HS 29.2 TABLE: Creepage distances, functional insulation Working voltage (V) Creepage distance (mm) ollution degree 1 2 3 Material group Material group I II IIIa/IIIb I II IIIa/IIIb* ) Verdict / Remark 10 0,08 0,4 0,4 0,4 1,0 1,0 1,0 50 0,16 0,56 0,8 1,0 1,4 1,6 1,8 125 0,25 0,71 1,0 1,4 1,8 2,0 2,2 250 0,42 1,0 1,4 2,0 2,5 2,8 3,2 B/W L and : 5,2 mm 400 0,75 1,6 2,2 3,2 4,0 4,5 5,0 500 1,0 2,0 2,8 4,0 5,0 5,6 6,3 630 and 800 1,8 3,2 4,5 6,3 8,0 9,0 10,0 800 and 1000 2,4 4,0 5,6 8,0 10,0 11,0 12,5 1000 and 1250 3,2 5,0 7,1 10,0 12,5 14,0 16,0 1250 and 1600 4,2 6,3 9,0 12,5 16,0 18,0 20,0 1600 and 2000 5,6 8,0 11,0 16,0 20,0 22,0 25,0 2000 and 2500 7,5 10,0 14,0 20,0 25,0 28,0 32,0 2500 and 3200 10,0 12,5 18,0 25,0 32,0 36,0 40,0 3200 and 4000 12,5 16,0 22,0 32,0 40,0 45,0 50,0 4000 and 5000 16,0 20,0 28,0 40,0 50,0 56,0 63,0 5000 and 6300 20,0 25,0 36,0 50,0 63,0 71,0 80,0 6300 and 8000 25,0 32,0 45,0 63,0 80,0 90,0 100,0 8000 and 10000 32,0 40,0 56,0 80,0 100,0 110,0 125,0 10000 and 12500 40,0 50,0 71,0 100,0 125,0 140,0 160,0 Supplementary information: * ) Material group IIIb is allowed if the working voltage does not exceed 50 V TRF o. IEC60335_2_80E
age 93 of 114 Report o.: STUESO017022702211HS 30 TABLE: Resistance to heat and fire Object/ part o. Manufactu rer/ trademark Type/ model Ball pressure test C Glow wire test (GWT) C Glow-wire flammability index (GWFI) C Glowwire ignition temp. (GWIT) C eedle - flame test (FT) Verdict Knob --- --- 0,95 mm Box of control panel lastic enclosure support main CB See 24.1 FR-500 0,9 mm See 24.1 FR-500 0,88 mm Main CB See 24.1 KB- 6160C CB of control panel See 24.1 KB- 6160C 75 125 cl. 11 +40 --- 0,83 mm --- 0,85 mm cl. 19 +25 --- --- --- 0s --- --- --- 0s --- --- --- 0s 550 650 750 850 550 650 750 850 675 775 te ti te ti --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- 0 s 0 s 0s --- --- --- --- --- 0 s 0 s 0s --- --- --- --- --- --- --- --- --- --- --- --- TRF o. IEC60335_2_80E
Relay See 24.1 HJR- 3FF-S-H Running capacitor Running capacitor Running capacitor Bobbin of motor Bobbin of transformer --- 0,8 mm See 24.1 CBB61 --- 0,88 mm See 24.1 CBB61 --- 0,85 mm See 24.1 CBB60 --- 0,87 mm --- --- --- 0,8 mm --- --- --- 0,8 mm age 94 of 114 Report o.: STUESO017022702211HS --- --- --- --- --- --- --- --- --- --- --- --- 0 0 0s s s --- --- --- --- --- 0 s 0 s 0s --- --- --- --- --- 0 s 0 s 0s --- --- --- --- --- 0 s 0 s 0s --- --- --- --- --- 0 s 0 s 0s --- --- --- --- --- 0 s 0 s 0s --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- Supplementary information: 1) arts of material classified at least HB40 or if relevant HBF 2) arts of material classified as V-0 or V-1 3) Flame persisting longer than 2 s (= te ti) need only be reported for unattended appliances 4) Surrounding parts subjected to the needle-flame test of annex E 5) Base material classified as V-0 or if relevant VTM-0 6) The GWIT pre-selection option, the 850 C GWFI pre-selection option, and the 850 C GWT are not applicable for attended appliances TRF o. IEC60335_2_80E
age 95 of 114 Report o.: STUESO017022702211HS Attachment 1: European Group Differences and ational Differences for E 60335-1, E 60335-2-80 and E 62233 according to. ATTACHMET TO TEST REORT EUROEA GROU DIFFERECES AD ATIOAL DIFFERECES (art 2: articular requirements for fans) Differences according to: E 60335-1:2012 + A11: 2014 E 60335-2-80:2003+A1:2004+A2:2009 E 62233:2008 Attachment Form o. : Attachment Originator: Master Attachment: 2012-09 EU_GD_IEC60335_2_80E DEKRA Certification B.V. Copyright 2012 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. CEELEC COMMO MODIFICATIOS 6.1 Delete class 0 and class 01 7.1 Single-phase appliances to be connected to the supply mains: 230 V covered Multi-phase appliances to be connected to the supply mains: 400 V covered 7.10 Devices used to start/stop operational functions of the appliance distinguished from other manual devices by means of shape, size, surface texture, position, etc. 230V An indication that the device has been operated is given by: a tactile feedback, or an audible and visual feedback 7.12 The instructions include the substance of the following: 7.12.Z1 - this appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved - children shall not play with the appliance - cleaning and user maintenance shall not be made by children without supervision The specific instructions related to the safe operation of this appliance is collated together in the front section of the user instructions The height of the characters, measured on the capital letters, is at least 3 mm TRF o. IEC60335_2_80E
age 96 of 114 Report o.: STUESO017022702211HS These instructions are also available in an alternative format, e.g. on a website 8.1.1 Also test probe 18 of E 61032 is applied The appliance being in every possible position during the test The force on the probe in the straight position is increased to 10 when probe 18 is used When using test probe 18 the appliance is fully assembled as in normal use without any parts removed, and parts intended to be removed for user maintenance are also not removed 8.2 Compliance is checked by applying the test probes of E 61032 For built-in appliances and fixed appliances, the test probe B and probe 18 of E 61032 are applied only after installation 11.8 Footnotes to External enclosure of motor-operated appliances to be taken into account 15.1.2 Appliances with an automatic cord reel tested with the cord in the most unfavourable position so that the reeling of the wet cord may affect electrical insulation during operation, the cord not being dried before reeling 20.2 When using the test probe similar to test probe B with a circular stop face, the accessories and detachable covers are removed Test probe 18 applied with a force of 2,5 on the appliance fully assembled 24.1 Components comply with the safety requirements specified in the relevant standards as far as they reasonably apply The requirements of Clause 29 of this standard apply between live parts of components and accessible parts of the appliance. The requirements of 30.2 of this standard apply to parts of non-metallic material in components including parts of non-metallic material supporting current-carrying connections inside components Components that have not been previously tested or do not comply with the standard for the relevant component are tested according to the requirements of 30.2 Components that have been previously tested and shown to comply with the resistance to fire requirements in the standard for the relevant component need not be retested provided that: TRF o. IEC60335_2_80E
age 97 of 114 Report o.: STUESO017022702211HS - the severity specified in the component standard is not less than the severity specified in 30.2, and - the test report for the component states whether it complied with the standard for the relevant component with or without flame, flames not exceeding 2 s during the test are ignored Unless components have been previously tested and found to comply with the relevant standard for the number of cycles specified, they are tested in accordance with 24.1.1 to 24.1.9 For components mentioned in 24.1.1 to 24.1.9, no additional tests specified in the relevant standard for the component are necessary other than those specified in 24.1.1 to 24.1.9 Components that have not been separately tested and found to comply with the relevant standard, and components that are not marked or not used in accordance with their marking, are tested in accordance with the conditions occurring in the appliance, the number of samples being that required by the relevant standard Lamp holders and starter holders that have not been previously tested and found to comply with the relevant standard are tested as a part of the appliance and additionally comply with the gauging and interchangeability requirements of the relevant standard under the conditions occurring in the appliance Where the relevant standard specifies these gauging and interchangeability requirements at elevated temperatures, the temperatures measured during the tests of Clause 11 are used lugs and socket-outlets and other connecting devices of interconnection cords are not interchangeable with plugs and socket-outlets listed in IEC/TR 60083 or IEC 60906-1, or with connectors and appliance inlets complying with the standard sheets of IEC 60320-1, if direct supply to these parts from the supply mains gives rise to a hazard 24.1.7 If the remote operation of the appliance is via a telecommunication network, the relevant standard for the telecommunication interface circuitry in the appliance is E 41003 TRF o. IEC60335_2_80E
age 98 of 114 Report o.: STUESO017022702211HS Compliance with Clause 8 of this standard is not impaired by connecting the appliance to a device covered by E 41003 24.Z1 For motor running capacitors (IEC 60252-1 type 2) with a metallic enclosure having an overpressure fuse the flame testing of internal plastic parts supporting current carrying connections as required in 30.2.2 and 30.2.3.1 is not necessary 25.6 Supply cords of single-phase portable appliances having a rated current not exceeding 16 A, fitted with a plug complying with the following standard sheets of IEC/TR 60083: - for Class I appliances: standard sheet C2b, C3b or C4... : - for Class II appliances: standard sheet C5 or C6... : 25.7 Rubber sheathed cords (60245 IEC 53) are not suitable for appliances intended to be used outdoors or when they are liable to be exposed to significant amount of ultraviolet radiation Halogen-free thermoplastic compound sheathed supply cords have properties at least those of: halogen-free thermoplastic compound sheathed cords (H03Z1Z1H2-F or H03Z1Z1-F), for appliances having a mass not exceeding 3 kg halogen-free thermoplastic compound sheathed cords (H05Z1Z1H2-F or H05Z1Z1-F), for other appliances Cross-linked halogen-free compound sheathed supply cords have properties at least those of cross-linked halogen-free compound sheathed cords (H07ZZ-F) 26.11 Conductors connected by soldering are not considered to be positioned or fixed so that reliance is not placed upon the soldering alone to maintain them in position unless they are held in place near the terminals independently of the solder 29.3.Z1 Appliance constructed so that if there is a possibility of damaging the insulation during installation, the insulation withstands the scratch and penetration test of 21.2 32 Compliance regarding electromagnetic fields is checked according to E 62233 E 62233 Annex I, 19.I.101 The appliance is supplied at rated voltage and operated under normal operation with each of the fault conditions specified TRF o. IEC60335_2_80E
age 99 of 114 Report o.: STUESO017022702211HS The duration of the test is as specified in 19.7 ZA AEX ZA (ORMATIVE) SECIAL ATIOAL CODITIOS orway 19.5 The test is also applicable to appliances intended to be permanently connected to fixed wiring orway 22.2 The second paragraph of this subclause, dealing with single-phase, permanently connected class I appliances having heating elements, is not applicable due to the supply system All CEELEC countries 25.6 and 25.25 Information concerning ational plug and socketoutlets is available from the CEELEC website. ormative national requirements concerning plug and socket-outlets are shown in the relevant ational standard Ireland and United Kingdom 25.8 In the table, the lines for 10 A and 16 A are replaced by: > 10 and 13 1,25 > 13 and 16 1,5 ZB AEX ZB (IFORMATIVE) A-DEVIATIOS Ireland 25.6 These regulations apply to all plugs for domestic use at a voltage of not less than 200 V and in general allow only plugs complying with I.S. 401:1997, or equivalent, to be fitted to domestic appliances United Kingdom TRF o. IEC60335_2_80E
age 100 of 114 Report o.: STUESO017022702211HS 25.6 These regulations apply to all plugs for domestic use at a voltage of not less than 200 V and in general allow only plugs to BS 1363 to be fitted to domestic appliances. It also allows plugs to BS 4573 and E 50075 to be fitted to shavers and toothbrushes ZC AEX ZC (ORMATIVE) ORMATIVE REFERECES TO ITERATIOAL UBLICATIOS WITH THEIR CORRESODIG EUROEA UBLICATIOS A list of referenced documents in this standard ZD AEX ZD (IFORMATIVE) IEC and CEELEC CODE DESIGATIOS FOR FLEXIBLE CORDS A table with IEC and CEELEC code designations for flexible cords ZE AEX ZE (IFORMATIVE) SECIFIC ADDITIOAL REQUIREMETS FOR ALIACES AD MACHIES ITEDED FOR COMMERCIAL USE 7.1 Business name and full address of the manufacturer and, where applicable, his authorized representative... : Model or type reference... : Serial number, if any... : roduction year Designation of the appliance... : 7.12 Instructions provided with the appliance so that the appliance can be used safely The instructions contain at least the following information: - the business name and full address of the manufacturer and, where applicable, his authorized representative - model or type reference of the appliance as marked on the appliance itself, except for the serial number - the designation of the appliance together with its explanation in case it is given by a combination of letters and/or numbers - the general description of the appliance, when needed due to the complexity of the appliance TRF o. IEC60335_2_80E
age 101 of 114 Report o.: STUESO017022702211HS - specific precautions if required during installation, operation, adjusting, user maintenance, cleaning, repairing or moving - when needed drawings, diagrams, descriptions and explanations necessary for the safe use and user maintenance of the appliance - the possible reasonably foreseeable misuse and, whenever relevant, a warning against the effects it may have on the safe use of the appliance The words Original instructions appear on the language version(s) verified by the manufacturer or by the authorized representative When a translation of the original instructions has been provided by a person introducing the appliance on the market; the meaning of the sentence Translation of the original instructions appear in the relevant instructions delivered with the appliance The instructions for maintenance/service to be done by specialized personnel, mandated by the manufacturer or the authorized representative may be supplied in only one Community language which the specialized personnel understand The instructions indicate the type and frequency of inspections and maintenance required for safe operation including the preventive maintenance measures 7.12.ZE1 If needed for specific appliances, the following information to be given: on use, transportation, assembly, dismantling when out of service, testing or foreseeable breakdowns, if these operations have consequences on stability of the appliance in order to avoid overturning, falling or uncontrolled movements of the appliance or of its component parts on how to maintain adequate mechanical stability when in use, during transportation, assembly, dismantling, scrapping and any other action involving the appliance on the protective measures to be taken by the user, including, where appropriate, the personal protective equipment to be provided on the operating method to be followed in the event of accident or breakdown; if a blockage is likely to occur the operating method to safely unblock the appliance TRF o. IEC60335_2_80E
age 102 of 114 Report o.: STUESO017022702211HS on the specifications on the spare parts to be used, when these affect the health and safety of the operator on airborne noise emissions, determined and declared in accordance with the relevant art 2, which includes: - the A-weighted emission sound pressure level at workstations, where this exceeds 70 db(a)... ; db(a), - where this level does not exceed 70 this fact is indicated - the peak C-weighted instantaneous sound pressure value at workstations, where this exceeds 63 a (130 db in relation to 20 μa)... : - the A-weighted sound power level emitted by the machinery, where the A-weighted emission sound pressure level at workstations exceeds 80 db(a)... : 7.12.ZE2 The instructions includes a warning to disconnect the appliance from its power source during service and when replacing parts If the removal of the plug is foreseen, it is clearly indicated that the removal of the plug has to be such that an operator can check from any of the points to which he has access that the plug remains removed If this is not possible, due to the construction of the appliance or its installation, a disconnection with a locking system in the isolated position is provided 19.11.4.8 The appliance continues to operate, without causing any hazard to the user, from the same point in its operating cycle at which the voltage fluctuation occurred, or a manual operation is required to restart it 20.1 Appliances and their components and fittings have adequate mechanical stability during transportation, assembly, dismantling and any other action involving the appliance 20.2 Dangerous moving transmission parts safeguarded either by design or guards When guards are used, they are fixed guards, interlocking movable guards or protective devices Moving parts directly involved in the function of the appliance which cannot be made completely inaccessible fitted with: TRF o. IEC60335_2_80E
age 103 of 114 Report o.: STUESO017022702211HS - fixed guards or interlocking movable guards preventing access to those sections of the parts that are not used in the work, and - adjustable guards restricting access to those sections of the moving parts where access is necessary Interlocking movable guards used where frequent access is required 21.1 Appliances and their components and fittings have adequate mechanical strength and is constructed to withstand such rough handling that may be expected in normal use, during transportation, assembly, dismantling, scrapping and any other action involving the appliance 22.ZE.1 22.ZE.2 22.ZE.3 22.ZE.4 22.ZE.5 For appliances provided with a seat, the seat gives adequate stability The distance between the seat and the control devices capable of being adapted to the operator For appliances provided with separate devices for the start and the stop functions, the stop function is unambiguously identifiable and does always override the start function For appliances provided with one device performing the start and the stop function, the stop function is unambiguously identifiable and does always override the start function Appliances designed in such a way that incorrect mounting is avoided, if this can lead to an unsafe situation If this is not possible, information on the correct mounting is given directly on the part and/or the enclosure Where the weight, size or shape prevents appliances from being moved manually, they are fitted with attachments for lifting gear, or so designed that they can be fitted with such attachments, or be shaped in such a way that standard lifting gear can easily be used Appliances to be moved manually are constructed or equipped so that they can be moved easily and safely The fixing systems of fixed guards which prevent access to dangerous moving transmission parts only removable with the use of tools TRF o. IEC60335_2_80E
age 104 of 114 Report o.: STUESO017022702211HS If such guards have to be removed by the user for routine cleaning or maintenance their fixing systems remain attached to the fixed guards or to the machine after removal 22.ZE.6 22.ZE.7 Where possible, guards are incapable of remaining in place without their fixings This does not apply if, after removal of the screws, or if the component is incorrectly repositioned, the appliance becomes inoperative Movable guards are interlocked The interlocking devices prevent the start of hazardous appliance functions until the guards are fixed in their position, and give a stop command whenever they are no longer closed Where it is possible for an operator to reach the danger zone before the risk due to hazardous appliance functions has ceased, movable guards associated with a guard locking device in addition to an interlocking device that: - prevents the start of hazardous appliance functions until the guard is closed and locked, and - keeps the guard closed and locked until the risk of injury from the hazardous appliance functions has ceased Interlocking movable guards remain attached to the appliance when open, and they are designed and constructed in such a way that they can be adjusted only by means of an intentional action Interlocking movable guards designed in such a way that the absence or failure of one of their components prevents starting or stops the hazardous appliance functions The guard is opened to the extent needed to cause the interlocking to operate and is then closed, the number of operations being defined in the specific art 2... : After this test any defect that may be expected in normal use is applied to the interlock system, including interruption of the supply, only one defect being simulated at a time After these tests the interlock system is fit for further use Adjustable guards restricting access to areas of the moving parts strictly necessary for the work are: - adjustable manually or automatically, depending on the type of work involved, and - readily adjustable without the use of tools TRF o. IEC60335_2_80E
22.ZE.8 age 105 of 114 Report o.: STUESO017022702211HS In case of interruption, re-establishment after an interruption or fluctuation in whatever manner of the power supply, the appliance does not restart 22.ZE.9 However, automatic restarting of the operation is allowed if the appliance may continue to operate, without causing any hazard to the user, from the same point in its operating cycle at which the voltage interruption or fluctuation occurred Appliances fitted with means to isolate them from all energy sources Such isolators are clearly identified, and they are capable of being locked if reconnection endanger persons After the energy source is disconnected, it is possible to dissipate any energy remaining or stored in the circuits of the appliance without risk to persons ZF AEX ZF (IFORMATIVE) CRITERIA ALIED FOR THE ALLOCATIO OF RODUCTS COVERED BY STADARDS I THE E 60335 SERIES UDER LVD OR MD List of standards under CEELEC/TC61 with the allocation under the LVD or the MD... : LVD ZG 7.12.ZG AEX ZG (ORMATIVE) UV ALIACES The following modifications to this standard apply to appliances having UV emitters This annex is not applicable to appliances covered by the scopes of IEC 60335-2-27, IEC 60335-2-59 or IEC 60335-2-109 The instructions for appliances incorporating UVC emitters include the substance of the following: WARIG This appliance contains a UV emitter. Do not stare at the light source 32 For appliances incorporating UV emitters the manufacturer delivers a declaration providing evidence that the plastic material exposed to the radiation is UV resistant ZZ AEX ZZ (IFORMATIVE) COVERAGE OF ESSETIAL REQUIREMETS OF EC DIRECTIVES Description of the relation between this European standard and the LVD and the MD. TRF o. IEC60335_2_80E
Annex E 62233:2008 age 106 of 114 Report o.: STUESO017022702211HS Clause Requirement + Test Result - Remark Verdict EMF- ELECTROMAGETICS FIELDS The tested product also complies with the requirements of E 62233:2008 Limit 100% Measured max. : 6,1 % *otes Tested at 240V 50Hz; Measuring distance: 30cm; Sensor location: Front; Operating conditions: Continuously; Background noise level: less than 0,235% of limit. TRF o. IEC60335_2_80E
age 107 of 114 Report o.: STUESO017022702211HS Attachment 2: hotos. Details of: General view (FM-1220T/Y) View: [ ] general [ X] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom Details of: General view (FM-1220T/Y) View: [ ] general [ ] front [ ] rear [ ] right [ ] left [ X] top [ ] bottom TRF o. IEC60335_2_80E
Details of: Right view (FM-1220T/Y) age 108 of 114 Report o.: STUESO017022702211HS View: [ X] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom Details of: General view (FM-1220T/Y) View: [ X] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom TRF o. IEC60335_2_80E
Details of: age 109 of 114 Report o.: STUESO017022702211HS General view (FM-1220T/Y) View: [ ] general [ ] front [ ] rear [ ] right [ ] left [ ] top [X ] bottom Details of: Internal view (FM-1209T/Y) View: [ X] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom TRF o. IEC60335_2_80E
Details of: age 110 of 114 Report o.: STUESO017022702211HS Internal view (FM-1209T/Y) View: [ X] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom Details of: Internal view (FM-1209T/Y) View: [ X] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom TRF o. IEC60335_2_80E
age 111 of 114 Report o.: STUESO017022702211HS Details of: Internal view (FM-1209T/Y) View: [ X] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom Details of: Main CB view (All models) View: [ X] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom TRF o. IEC60335_2_80E
Details of: age 112 of 114 Report o.: STUESO017022702211HS Main CB view (All models) View: [ X] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom Details of: Control panel view (All models) View: [ X] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom TRF o. IEC60335_2_80E
Details of: age 113 of 114 Report o.: STUESO017022702211HS CB of control panel view (All models) View: [ X] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom Details of: CB of control panel view (All models) View: [ X] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom TRF o. IEC60335_2_80E
Details of: age 114 of 114 Report o.: STUESO017022702211HS Control panel view (All models) View: [ X] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom Details of: Remote control view (All models) View: [X] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom ---End of report--- TRF o. IEC60335_2_80E