IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of the supplier's factory and warehouses as well as the assessment of the supplier's Quality Assurance System. This listing is subject to the conditions set forth in the characteristics below and is not to be construed as any recommendation, assurance or guarantee by IAPMO Research and Testing, Inc. of the product acceptance by Authorities Having Jurisdiction. The most updated information on this Certificate of Listing is available online at pld.iapmo.org Effective Date: October 2016 Void After: October 2017 Product: Air Admittance Valves File No. C-3803 Issued To: IPS Corporation 202 Industrial Park Lane Collierville, TN 38017 Identification: Manufacturer's name or trademark, model designation, and the C/IAPMO triangular certification mark. Characteristics: Air admittance valves designed to permit air to enter the drainage system when the pressure within the system drops below atmospheric pressure. To be installed in accordance with the manufacturer's instructions. The device shall be installed in an accessible location which shall permit free (unobstructed) movement of air into the device. The device shall be insalled in a vertical and upright orientation not to exceed 15 degrees from the vertical plumb. Products listed on this certificate have been tested by an IAPMO R&T recognized laboratory. This recognition has been granted based upon the laboratory's compliance to the applicable requirements of ISO/IEC 17025. Products are in compliance with the following standard(s): ASSE 1051-2009 This listing period is based upon the last date of the month indicated on the Effective Date and Void After Date shown above. Any change in material, manufacturing process, marking or design without having first obtained the approval of the Product Certification Committee, or any evidence of non-compliance with applicable codes and standards or of inferior workmanship, may be deemed sufficient cause for revocation of this listing. Production of or reference to this form for advertising purposes may be made only by specific written permission of IAPMO Research and Testing, Inc. Any alteration of this certificate could be grounds for revocation of the listing. This document shall be reproduced in its entirety.
Page 2 Void After: October 2017 Product: Air Admittance Valves File No. C-3803 Issued To: Ips Corporation MODELS: Note: Model number on the product is an internal identification number for IPS in reference to the packaging size or bulk quantity. Studor Maxi-Vent Mini-Vent Redi-Vent Tec-Vent
Page 3 Void After: October 2017 Product: Air Admittance Valves File No. C-3803 Issued To: Ips Corporation ADDITIONAL COMPANY INFO: Hajoca Corporation Brigade TM / Mainline TM Model No. BR10464/ML10464 BR10465/ML10465 BR10466/ML10466 BR10469/ML10469 BR10470/ML10470 Description Maxi Vent PVC Mini Vent PVC adaptor Mini Vent ABS adaptor Redi Vent PVC adaptor Redi Vent ABS adaptor
IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of the supplier's factory and warehouses as well as the assessment of the supplier's Quality Assurance System. This listing is subject to the conditions set forth in the characteristics below and is not to be construed as any recommendation, assurance or guarantee by IAPMO Research and Testing, Inc. of the product acceptance by Authorities Having Jurisdiction. The most updated information on this Certificate of Listing is available online at pld.iapmo.org Effective Date: March 2016 Void After: March 2017 Product: STACK AIR ADMITTANCE VALVES File No. C-7729 Issued To: Ips Corporation 202 Industrial Park Lane Collierville, TN 38017 Identification: Manufacturer's name or trademark, model designation, and the C/IAPMO triangular certification mark. Characteristics: Air admittance valves designed to permit air to enter the drainage system when the pressure within the system drops below atmospheric pressure. To be installed in accordance with the manufacturer's instructions. Products listed on this certificate have been tested by an IAPMO R&T recognized laboratory. This recognition has been granted based upon the laboratory's compliance to the applicable requirements of ISO/IEC 17025. Products are in compliance with the following standard(s): ASSE 1050-2009 This listing period is based upon the last date of the month indicated on the Effective Date and Void After Date shown above. Any change in material, manufacturing process, marking or design without having first obtained the approval of the Product Certification Committee, or any evidence of non-compliance with applicable codes and standards or of inferior workmanship, may be deemed sufficient cause for revocation of this listing. Production of or reference to this form for advertising purposes may be made only by specific written permission of IAPMO Research and Testing, Inc. Any alteration of this certificate could be grounds for revocation of the listing. This document shall be reproduced in its entirety.
Page 2 Void After: March 2017 Product: STACK AIR ADMITTANCE VALVES File No. C-7729 Issued To: Ips Corporation MODELS: Maxi-Vent Mini-Vent Redi-Vent Tec-Vent
Page 3 Void After: March 2017 Product: STACK AIR ADMITTANCE VALVES File No. C-7729 Issued To: Ips Corporation ADDITIONAL COMPANY INFO: Hajoca Corporation BR10469 / ML10469 BR10470 / ML10470 BR10465 / ML10465 BR10466 / ML10466 BR10464 / ML10464 (Redi Vent PVC) (Redi Vent ABS) (Mini Vent PVC) (Mini Vent ABS) (Maxi Vent PVC)
ICC-ES Report PMG-1025 Reissued 02/2016 This report is subject to renewal 02/2017 EVALUATION SUBJECT: STUDOR AIR ADMITTANCE VALVES DIVISION: 22 00 00 PLUMBING SECTION: 22 13 19.36 AIR ADMITTANCE VALVE Report Holder: STUDOR, INC., DIVISION OF IPS CORPORATION 500 DISTRIBUTION PARKWAY COLLIERVILLE, TN 38017
ICC-ES PMG Listing PMG-1025 Effective Date: February 2016 This listing is subject to re-examination in one year. www.icc-es-pmg.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council CSI: DIVISION: 22 00 00 PLUMBING Section: 22 13 19.36 Air Admittance Valve Product certification system: The ICC-ES product certification system includes testing samples taken from the market or supplier s stock, or a combination of both, to verify compliance with applicable codes and standards. The system also involves factory inspections, and assessment and surveillance of the supplier s quality system. Product: Studor Air Admittance Valves: Mini-Vent, Maxi-Vent, Redi-Vent, Tec-Vent, Trap-Vent Listee: Studor, Inc., Division of IPS Corporation 500 Distribution Parkway Collierville, Tennessee 38017 www.studor.com Additional listees: Hajoca (Mainline brand) 1942 Airport Road Monroe, NC 28110 Compliance with the following codes: 2015, 2012 and 2009 International Plumbing Code (IPC) 2015, 2012 and 2009 International Residential Code (IRC) 2012 and 2009 National Standard Plumbing Code (NSPC)* *National Standard Plumbing Code is a copyrighted publication of Plumbing-Heating-Cooling-National Association Compliance with the following standards: ASSE 1050 2009, Performance Requirements for Stack Air Admittance Valves for Sanitary Drainage Systems ASSE 1051 2009, Performance Requirements for Individual and Branch Type Air Admittance Valves for Sanitary Drainage Systems- Fixture and Branch Devices NSF Standard 14 2015, Plastic Piping System Components and Related Materials Listings are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the listing or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this listing, or as to any product covered by the listing. Copyright 2016 ICC Evaluation Service, LLC. All rights reserved. Page 1 of 6
PMG-1025 Most Widely Accepted and Trusted Page 2 of 6 Identification: Installation: Models: Conditions of listing: The Studor Mini-Vent, Maxi-Vent, Redi-Vent, Tec-Vent and Trap-Vent must be identified by molded lettering on the lid, indicating the name of the product, the manufacturer s name, manufacturing location (Ellington, Connecticut), and the ICC-ES PMG listing mark. Studor Mini-Vent, Maxi-Vent, Redi-Vent, Tec-Vent and Trap-Vent must be installed in accordance with the manufacturer s installation instructions and the conditions of this listing. The Studor Mini-Vent, Maxi-Vent, Redi-Vent, Tec-Vent and Trap-Vent are air admittance valves conforming to ASSE 1050, ASSE 1051 and NSF 14. The Mini-Vent and Redi-Vent are designed for pipe sizes of 1 1 / 2 inches through 2 inches (38 mm through 51 mm). The Maxi-Vent is designed for pipe sizes of 3 inches through 4 inches (76 mm through 102 mm). The Tec-Vent is designed for 1 1 / 2 inch pipe (38mm). The Trap-Vent is designed for 1 ¼ inches through 1 ½ inches pipe. The Studor air admittance valves are used as a vent termination for individual vents, common vents, circuit vents and branch vents. Mini-Vent, Maxi-Vent, Redi-Vent, Tec-Vent and Trap-Vent are also permitted to be used as the vent termination for a vent stack or stack vent with six branch intervals or less. 1. The Studor Mini-Vent and Redi-Vent are supplied with a connector which enables the valve to be solvent cemented onto 1 1 / 2 -inch- or 2-inch-diameter (38 mm or 51 mm) pipes or screwed into 1 1 / 2 - inch (38 mm) I.P.S. threads. The Tec-Vent has 1 1 / 2 (38mm) I.P.S. threads and does not come with a connector. 2. The Studor Maxi-Vent is supplied with a synthetic rubber connector which enables the valve to be push fitted into a 4-inch-diameter (102 mm) PVC, cast iron or ABS pipe. It may also be installed on a 3-inch-diameter (76 mm) PVC, cast iron or ABS pipe in accordance with the manufacturer s instructions. 3. The use of Studor Mini-Vent, Maxi-Vent, Redi-Vent, Tec-Vent and Trap-Vent is limited to systems subject to siphonage conditions and a maximum pressure condition of 1-inch (25 mm) water column. 4. Each Studor Mini-Vent, Maxi-Vent, Redi-Vent, Tec-Vent and Trap-Vent must be located a minimum of 4 inches (102 mm) above the horizontal branch drain or fixture drain being vented when providing trap seal protection for fixtures or branches. When serving as vent terminals for stack vents or vent stacks, they must be a minimum of 6 inches (152 mm) above the flood level rim of the highest fixture served. 5. Each Studor Mini-Vent, Maxi-Vent, Redi-Vent, Tec-Vent and Trap-Vent must be accessible for replacement if required. 6. The Studor Mini-Vent, Maxi-Vent, Redi-Vent, Tec-Vent and Trap-Vent must be located to allow adequate air to enter the valve. When the products are located in a wall space or attic space, ventilation openings must be provided into the space. When in an attic space, the vents must be located a minimum of 6 inches (152 mm) above any ceiling insulation. 7. The air-admittance valve must be installed in the vertical upright position. The maximum offset from the vertical upright position must not exceed 15 degrees. 8. Each vent must connect to the drain with a vertical connection to maintain an unblocked opening in the piping to the air admittance valves.
PMG-1025 Most Widely Accepted and Trusted Page 3 of 6 9. A minimum of one vent stack or stack vent must extend outdoors to the open air for every building plumbing drainage system unless specifically engineered. 10. The Studor Mini-Vent, Maxi-Vent, Redi-Vent, Tec-Vent and Trap-Vent are permitted to be installed as the vent termination for a vent stack or stack vent with six branch intervals or less or as a branch vent terminal for fixtures on the same floor. 11. The air admittance valves must be installed after the drainage system has been pressure tested. 12. When a horizontal branch connects to a stack more than four branch intervals from the top of the stack, a relief vent must be provided. The relief vent must be located between the connection of the branch to the stack and the first fixture connecting to the branch. The relief vent may also serve as a vent for a single fixture. The relief vent must connect to the vent stack or stack vent and extend to the open air outside the building. 13. The air admittance valves shall not be installed in non-neutralized special waster systems as described in chapter 8 of IPC. 14. The air admittance valves shall not be located in spaces utilized as supply or return air plenums. 15. The air admittance valves without an engineered design (See Figure 11) shall not be utilized to vent sumps or tanks of any type. 16. The Studor Mini-Vent, Maxi-Vent, Redi-Vent and Tec-Vent are produced in Ellington, Connecticut; the Studor Trap-Vent is produced in Darul Eshan, Malaysia under annual surveillance audits by ICC-ES. TABLE 1 AIR ADMITTANCE VALVE MODELS NUMBERS OF STUDOR/IPS NAME ONLY DESCRIPTION Mini Vent w/ PVC adaptor Mini Vent w/ ABS adaptor Maxi Vent USA PVC Redi Vent - w/ PVC adaptor Redi Vent - w/ ABS adaptor Tec Vent Trap Vent TABLE 2 AIR ADMITTANCE VALVE CROSS REFERENCE OF MODEL NUMBERS, STUDOR AND HAJOCA STUDOR/IPS PART NO. DESCRIPTION HAJOCA CORP. (BRIDAGE / MAINLINE BRAND) MODEL NO. 20302 Maxi Vent USA PVC (25 pack) BR10464 / ML10464 20305 X-Pack Mini Vent-PVC (40 pack) BR10465 / ML10465 20336 X-Pack Mini Vent-ABS (40 pack) BR10466 / ML10466 20386 Redi Vent-PVC (120 pack) BR10469 / ML10469 20389 Redi Vent-ABS (120 pack) BR10470 / ML10470 The following diagrams are examples of acceptable designs using the Mini-Vent, Maxi-Vent, Redi-Vent and Tec-Vent
PMG-1025 Most Widely Accepted and Trusted Page 4 of 6 TRAP-VENT TRAP-VENT
PMG-1025 Most Widely Accepted and Trusted Page 5 of 6
PMG-1025 Most Widely Accepted and Trusted Page 6 of 6 Figure 11
0 ICC-ES Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 Most Widely Accepted and Trusted PMG-1099 Valid: 10/15 to 10/16 DIVISION: 22 00 00 PLUMBING SECTION: 22 13 19.36 AIR ADMITTANCE VALVES REPORT HOLDER: IPS CORPORATION 500 DISTRIBUTION PARKWAY COLLIERVILLE, TENNESSEE 38017 EVALUATION SUBJECT: STUDOR AIR ADMITTANCE VALVE BOX Look for the trusted marks of Conformity! 2014 Recipient of Prestigious Western States Seismic Policy Council (WSSPC) Award in Excellence A Subsidiary of ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this report, or as to any product covered by the report. Copyright 2015
ICC-ES PMG Listing PMG-1099 Effective Date: October 2015 This listing is subject to re-examination in one year. www.icc-es-pmg.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council CSI: DIVISION: 22 00 00 PLUMBING Section: 22 13 19.36 Air Admittance Valves Product certification system: The ICC-ES product certification system includes testing samples taken from the market or supplier s stock, or a combination of both, to verify compliance with applicable codes and standards. The system also involves factory inspections, and assessment and surveillance of the supplier s quality system. Product: Listee: Studor Air Admittance Valve Box IPS Corporation 500 Distribution Parkway Collierville, Tennessee 38017 www.ipscorp.com Compliance with the following codes: 2015, 2012 and 2009 International Plumbing Code (IPC) 2015, 2012 and 2009 International Residential Code (IRC) 2015, 2012 and 2009 Uniform Plumbing Code (IAPMO UPC)* *Uniform Plumbing Code is a copyrighted publication of the International Association of Plumbing and Mechanical Officials Compliance with the following standards: Identification: Installation: Models: IAPMO PS-54-2014a Material and Property Standard for Metallic and Plastic Utility Boxes The Studor Air Admittance Valve Box described in this listing must be permanently and legibly marked with manufacturer s name or trade mark and the ICC-ES PMG listing mark. Studor Air Admittance Valve Box may vary in dimensions of height, width and depth. Installation must be in accordance with manufacturer s published installation instructions and correct plumbing practices contained in the current edition of the International Plumbing Code, Uniform Plumbing Code and International Residential Code. Studor Air Admittance Valve Box Model 20380 Series is a utility box manufactured from a High Impact Polystyrene that meets the requirements of IAPMO Standard PS-54. Listings are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the listing or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this listing, or as to any product covered by the listing. Copyright 2015 Page 1 of 2
PMG-1099 Most Widely Accepted and Trusted Page 2 of 2 Conditions of Listing: 1. Studor Air Admittance Valve Box recognized in the listing must be installed in accordance with the manufacturer s published installation instructions and the applicable codes. 2. Studor Air Admittance Valve Box is manufactured by IPS Corporation in Collierville, Tennessee under a quality control program with annual surveillance inspections by ICC-ES.
Report prepared for: Spec Direct (Free User) on 11/4/2016 11:57:25 AM LISTING INFORMATION OF Studor Air Admittance Valves Models Mini-Vent, Maxi-Vent & REDI-VENT SPEC ID: 38210 IPS Corporation (TN) 202 Industrial Park Lane Collierville, TN 38017 This report is for the exclusive use of Intertek s Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. IPS Corporation (TN) 38210 Rev: Aug 15 2016 8:24AM Uncontrolled Copy Page 1 of 2
Report prepared for: Spec Direct (Free User) on 11/4/2016 11:57:25 AM Product Type: Fitting - Air Admittance Valve Model Name: Mini-Vent Sizes: 1-1/4" (32 mm), 1-1/2" (38 mm) and 2" (50 mm). Model Name: Maxi-Vent Sizes: 3" (75 mm) and 4" (100 mm). Model Name: REDI-VENT Sizes: 1-1/2" and 2". EVALUATED TO THE FOLLOWING: ASSE 1050 Performance Requirements for AIr Admittance Valves for Plumbing DWV Systems - Stack type Devices ASSE 1051 Air Admittance Valves for Plumbing Drainage Systems - Fixture and Branch Devices IDENTIFICATION: All required marking must be permanent, legible and visible after manufacture. Markings consist of the WHI Certification Mark and the Markings required by the relevant standard(s). Attribute Value Criteria ASSE 1051 (2002) Criteria ASSE 1050 (1991) CSI Code 22 40 00 Plumbing Fixtures Intertek Services Certification Listed or Inspected LISTED Listing Section PLUMBING FITTINGS & ACCESSORIES Report Number 478-3598; 478-3073088-1/99 Edition 4 Spec ID 38210 Test Original Issue Date September 3, 1999 IPS Corporation (TN) 38210 Rev: Aug 15 2016 8:24AM Uncontrolled Copy Page 2 of 2
11/4/2016 Listing Category Search Page NSF International The Public Health and Safety Organization NSF Product and Service Listings These NSF Official Listings are current as of Friday, November 04, 2016 at 12:15 a.m. Eastern Time. Please contact NSF International to confirm the status of any Listing, report errors, or make suggestions. Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/certified/plumbing/listings.asp?company=73090&standard=014& NSF/ANSI 14 Plastics Piping System Components and Related Materials Click here for a list of End Use Code Designations. Click on Product Standards or footnote in blue to view the referenced document Studor Inc. 500 Distribution Parkway Collierville, TN 38017 United States 800 489 4848 901 853 5001 Visit this company's website (http://www.studor.com) Facility : Somers, CT Drain, Waste, and Vent Pipe and Fittings Product Type Material Type Trade Name Product Standard Air Admittance Valve ABS MINI VENT ASSE 1050 1 1/2", 2" Air Admittance Valve ABS MINI VENT ASSE 1051 1 1/2", 2" Product is authorized to bear the cnsf and/or the cnsfus Mark. http://info.nsf.org/certified/plumbing/listings.asp?company=73090&standard=014 1/3
11/4/2016 Listing Category Search Page NSF International Air Admittance Valve ABS MAXI VENT ASSE 1050 3", 4" Air Admittance Valve ABS MAXI VENT ASSE 1051 3", 4" Product is authorized to bear the cnsf and/or the cnsfus Mark. Air Admittance Valve ABS REDI VENT ASSE 1050 1 1/2", 2" Air Admittance Valve ABS REDI VENT ASSE 1051 1 1/2", 2" Product is authorized to bear the cnsf and/or the cnsfus Mark. Air Admittance Valve PC TEC VENT ASSE 1050 1 1/2", 2" Air Admittance Valve PC TEC VENT ASSE 1051 1 1/2", 2" Product is authorized to bear the cnsf and/or the cnsfus Mark. NOTE: Only products bearing the NSF Mark are Certified. Facility : Collierville, TN Drain, Waste, and Vent Pipe and Fittings Product Type Material Type Trade Name Product Standard Air Admittance Valve PP CHEM VENT ASSE 1049 1 1/2", 2" Product is authorized to bear the cnsf and/or the cnsfus Mark. NOTE: Only products bearing the NSF Mark are Certified. http://info.nsf.org/certified/plumbing/listings.asp?company=73090&standard=014 2/3
11/4/2016 Listing Category Search Page NSF International Facility : Shahalam, Selangor, Malaysia Drain, Waste, and Vent Pipe and Fittings Product Type Material Type Trade Name Product Standard Air Admittance Valve ABS Trap ASSE Vent* 1051 * Tailpieces and adapters were not tested or Listed by NSF International for this production location. Product can also come with white cladding, model 20496. Number of matching Manufacturers is 1 Number of matching Products is 10 Processing time was 0 seconds http://info.nsf.org/certified/plumbing/listings.asp?company=73090&standard=014 3/3
11/4/2016 Listing Category Search Page NSF International The Public Health and Safety Organization NSF Product and Service Listings These NSF Official Listings are current as of Friday, November 04, 2016 at 12:15 a.m. Eastern Time. Please contact NSF International to confirm the status of any Listing, report errors, or make suggestions. Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http://info.nsf.org/certified/plumbing/listings.asp?company=73090&standard=0mp& MP Mechanical Plumbing Products Studor Inc. 500 Distribution Parkway Collierville, TN 38017 United States 800 489 4848 901 853 5001 Visit this company's website (http://www.studor.com) Facility : Shahalam, Selangor, Malaysia Product Type Material Type Trade Product Name Standard Air Admittance Valve ABS Trap ASME Vent* A112.18.2 * Tailpieces and adapters were not tested or Listed by NSF International for this production location. Product can also come with white cladding, model 20496. Number of matching Manufacturers is 1 Number of matching Products is 1 Processing time was 0 seconds http://info.nsf.org/certified/plumbing/listings.asp?company=73090&standard=0mp 1/1