62DA,DB,DC,DD,DE,DF07-38

62D-3SB 62DA,DB,DC,DD,DE,DF07-38 DEDICATED VERTICAL OR HORIZONTAL 100% OUTDOOR AIR UNIT PERFORMANCE DATA UNIT DIMENSION PRINTS ACCESSORY DIMENSION PRINTS Copyright 2011 Carrier Corporation Syracuse, New York 13221 Form 62D-3SB Replaces: 62D-2SB Printed in U.S.A. 10-11 Catalog No. 0-1620003-01

Date: Supersedes: 62DA,DB,DC,DD,DE,DF07-38 DEDICATED VERTICAL OR HORIZONTAL 100% OUTDOOR AIR UNIT 62DA,DB,DC,DD, DE,DF Rev.: -3SB JOB NAME: LOCATION: BUYER: BUYER P.O. # CARRIER # UNIT NUMBER: MODEL NUMBER: PERFORMANCE DATA CERTIFIED BY: DATE: DESCRIPTION All Carrier 62DA, DB, DC, DD, DE, DF dedicated outdoor air products are pre-wired, charged with R-10A, and tested in both cooling and heating modes at the factory. All 62DA, DB, DC, DD, DE,DF units feature an industrial grade cabinet with fully hinged access panels. Superior supply fan performance with up to 3. in. wg external static pressure is standard. The 62D Series units are available in dedicated vertical or horizontal supply configurations. The 62DC,DD,DE,DF units are also available with an energy recovery wheel or exhaust. A wide variety of heating options are available. All 62D Series units come standard with microprocessor control. PERFORMANCE FEATURES Puron HFC refrigerant (R-10A). High-efficiency scroll compressors. Thermostatic expansion valve (TXV) refrigerant metering device for each circuit. Two-stage cooling on sizes 07, 08, 09 units, three or more stages on sizes 12 to 38. Hot gas bypass. Cooling operation range up to 11 F ambient and down to 3 F ambient. 2-volt control circuit. Rubber fan vibration isolators. Double wall design. Sloped, insulated, stainless steel condensate pan. Two-inch disposable-type air filters (optional -in. available). Fixed speed belt-type blower drive. High-efficiency motors meet EISA ( HP and larger). Two-position outside-air damper is standard, on 100% OA units capable of admitting 100% outdoor air during fan operation, closed when the fan is off. Modulating economizer is standard on recirculating units. Rated in accordance with AHRI Standard 210 or 0. Tested in accordance with UL Standard 199. Listed by ETL and ETL, Canada. Microprocessor control with: Occupancy schedule Password protection Service diagnostics Alarms and alarm history Short-cycle compressor protection Support of communication with BACnet* and Modbus protocols Remote start/stop capability STANDARD UNIT FEATURES MAINTENANCE FEATURES Large hinged service access doors. Slide out fan system. INSTALLATION FEATURES Single point electrical service entry, through unit bottom or side. Rigging openings in base rail. RELIABILITY FEATURES Dual electrically and mechanically independent refrigeration circuits (Sizes 12 to 38). Crankcase heaters are standard on all models. Compressor protection includes high and low pressure switches. Freeze protection. Liquid line filter driers. Circuit breaker protection for all power components. Cabinet made of pre-painted, galvanized steel with baked enamel finish, which meets ASTM B117 salt spray resistance. Condenser-fan motors are open drip proof, with internal protection. GAS HEATING SYSTEM FEATURES Stainless steel heat exchanger. Induced draft combination for safety and reliability. Two-stage gas valves with redundant 100% shutoff. Direct spark ignition. STANDARD WARRANTY Standard one-year warranty. Five-year non pro-rated warranty on heat exchanger. * Sponsored by ASHRAE (American Society of Heating, Refrigerating, and Air Conditioning Engineers). Registered trademark of Schneider Electric. 2

PERFORMANCE DATA Supply Air cfm ESP Exhaust Air cfm ESP COOLING COIL Entering Air db F wb F Total Capacity Btuh Sensible Capacity Btuh Latent Capacity Btuh Leaving Air db F wb F Liquid Subcooling Circuits Liquid Subcooling Rise (Max) F Leaving Subcooling Coil Temperature db F Hot Gas Reheat Circuits Hot Gas Reheat Capacity Btuh Hot Gas Reheat Rise (Max) F Hot Gas Reheat Leaving Air Temperature db F Unit Power Consumption kw Unit Efficiency EER OPTIONAL ENERGY CONSERVATION WHEEL SUMMER CONDITIONS Entering Air db F wb F Return Air db F wb F Total Capacity Btuh Sensible Capacity Btuh WINTER CONDITIONS Entering Air db F wb F Return Air db F wb F Total Capacity Btuh Sensible Capacity Btuh OPTIONAL GAS HEAT Input Btuh Output Btuh Total Temperature Rise F Entering-Air Temperature F Leaving-Air Temperature F OPTIONAL ELECTRIC HEAT Total Heating Capacity kw Heat Output Btuh Total Temperature Rise F Entering-Air Temperature F Leaving-Air Temperature F OPTIONAL HOT WATER HEATING COIL Fluid Type Flow Gpm Total Heating Capacity Btuh Entering Water Temperature F Leaving Water Temperature F Total Temperature Rise F Entering-Air Temperature F Leaving-Air Temperature F OPTIONAL STEAM HEATING COIL Steam Pressure psi Condensate Flow lb/hr Total Heating Capacity Btuh Total Temperature Rise F Entering-Air Temperature F Leaving-Air Temperature F ELECTRICAL DATA Power Supply to Unit Volts Phase Hz Minimum Circuit Amps Maximum Overcurrent Protection SUBMITTAL DATA Job Name Architect Engineer Contractor Unit Designation 3

OPTIONS AND ACCESSORIES Gas Heat Gas Heat with Space Temperature Override Electric Heat Hot Water Heating Coil Steam Heating Coil Energy Conservation Wheel Energy Conservation Wheel with VFD Defrost Control Energy Conservation Wheel with Return Air Bypass Filter Status Switch Phase/Voltage Monitor with Energy Management Relay Firestat VFD on IFM VFD on PE motor Convenience Outlet Disconnect Switch FACTORY-INSTALLED OPTIONS Hot Gas Reheat Coil Liquid Subcooling Coil Coated Coils -in. MERV 8 Filters -in. MERV 11 Filters -in. MERV 1 Filters 2-in. Metal Mesh Filters Backward Inclined Supply Fan Forward Curved Exhaust Fan Backward Curve Fan Airfoil Fan LonWorks* Communication Digital Compressor Return Air Smoke Detector CO 2 Sensor Roof Curb (1 in.) Roof Curb (2 in.) FIELD-INSTALLED ACCESSORIES BACview Handheld Keypad Display OTHER SPECIAL ITEMS * Registered trademark of Echelon Corporation.

UNIT DIMENSION PRINT 62DA,DB07-09 STANDARD UNIT 38 1/2 3 1/2 1 TYP. 96 7 20 TOP VIEW 7 1/2 SUPPLY 6 1/2 1 1/2 CUT ALONG DOTTED LINE CUT ALONG DOTTED LINE POWER THROUGH THE CURB SIDE VIEW (HORIZONTAL SUPPLY) 32 20 16 1/2 39 3/ SUPPLY FAN 62 2 1/2 82 1/2 97 1/8 a62-6 38 1/ 1 /8 8 CONTROL PANEL FILTER ACCESS FRONT VIEW CONDENSATE DRAIN PAN OUTSIDE AIR INTAKE HOOD NOTES: 1. Carrier recommends a minimum of 2 to -in. of service clearance on all sides of unit except for the control panel side, which should have at least 8-in. clearance. Top should be unobstructed. 2. Dimensions are in inches.

UNIT DIMENSION PRINT 62DC,DD,DE,DF07-09 UNIT WITH OPTIONAL EXHAUST 38 1/2 1 TYP. 96 7 1/2 3 1/2 7 20 SUPPLY 3 1/2 30 1/ 20 RETURN TOP VIEW 1 1/2 6 1/2 1 1/2 9 7/8 POWER THROUGH THE CURB 39 3/ 2 1/2 106 3/ 82 1/2 2 1/8 SIDE VIEW (HORIZONTAL SUPPLY) SUPPLY FAN CONTROL PANEL FILTER ACCESS 32 FRONT VIEW 20 16 1/2 62 OUTSIDE AIR INTAKE HOOD 38 1/ 8 CONDENSATE DRAIN PAN a62-6 NOTES: 1. Carrier recommends a minimum of 2 to -in. of service clearance on all sides of unit except for the control panel side, which should have at least 8-in. clearance. Top should be unobstructed. 2. Dimensions are in inches. 6

UNIT DIMENSION PRINT 62DC,DD,DE,DF07-09 UNIT WITH OPTIONAL ENERGY CONSERVATION WHEEL 38 1/2 3 1/2 3 1/2 96 1TYP 7 20 30 1/ 20 3 7/8 T OP VIEW 7 1/2 SUPPLY RETURN 6 1/2 1 1/2 1 1/2 CUT ALONG DOTTED LINE CUT ALONG DOTTED LINE POWER THROUGH THE CURB SIDE VIEW (HORIZONTAL SUPPLY) 32 20 16 1/2 39 3/ S UPPLY FAN 62 2 1/2 10 /8 128 3/ a62-66 97/8 2 1/8 CONTROL PANEL 38 1/ CONDENSATE 8 DRAIN PAN FILTER ACCESS F RONT VIEW OUTSIDE AIR INTAKE HOOD EXHAUST NOTES: 1. Carrier recommends a minimum of 2 to -in. of service clearance on all sides of unit except for the control panel side, which should have at least 8-in. clearance. Top should be unobstructed. 2. Dimensions are in inches. 7

UNIT DIMENSION PRINT 62DA,DB12-20 STANDARD UNIT 38 1/2 1 TYP. TOP VIEW 96 7 3 1/2 20 7 1/2 SUPPLY 1 1/2 6 1/2 POWER THROUGH THE CURB 39 3/ 2 1/2 82 1/2 97 1/8 1 /8 SIDE VIEW (HORIZONTAL SUPPLY) 32 SUPPLY FAN CONTROL PANEL FILTER ACCESS FRONT VIEW 62 20 16 1/2 OUTSIDE AIR INTAKE HOOD 38 1/ 8 CONDENSATE DRAIN PAN a62-67 NOTES: 1. Carrier recommends a minimum of 2 to -in. of service clearance on all sides of unit except for the control panel side, which should have at least 8-in. clearance. Top should be unobstructed. 2. Dimensions are in inches. 8

UNIT DIMENSION PRINT 62DC,DD,DE,DF12-20 UNIT WITH OPTIONAL EXHAUST 38 1/2 1 TYP. 96 7 1/2 7 3 1/2 20 30 1/ 20 SUPPLY RETURN 3 1/2 TOP VIEW 1 1/2 6 1/2 1 1/2 CUT ALONG DOTTED LINE CUT ALONG DOTTED LINE POWER THROUGH THE CURB SIDE VIEW (HORIZONTAL SUPPLY) 32 20 16 1/2 39 3/ 2 1/2 82 1/2 106 3/ SUPPLY FAN 62 a62-68 9 7/8 2 1/8 CONTROL PANEL 38 1/ CONDENSATE 8 DRAIN PAN FILTER ACCESS FRONT VIEW OUTSIDE AIR INTAKE HOOD EXHAUST NOTES: 1. Carrier recommends a minimum of 2 to -in. of service clearance on all sides of unit except for the control panel side, which should have at least 8-in. clearance. Top should be unobstructed. 2. Dimensions are in inches. 9

UNIT DIMENSION PRINT 62DC,DD,DE,DF12-20 UNIT WITH OPTIONAL ENERGY CONSERVATION WHEEL 38 1/2 96 1 TYP. 7 3 1/2 3 1/2 20 30 1/ 20 3 7/8 TOP VIEW 7 1/2 SUPPLY RETURN 1 1/2 6 1/2 1 1/2 3/8 39 3/ 2 1/2 9 7/8 POWER THROUGH THE CURB 10 /8 2 1/8 128 3/ SIDE VIEW (HORIZONTAL SUPPLY) SUPPLY FAN CONTROL PANEL FILTER ACCESS 32 FRONT VIEW 20 16 1/2 62 OUTSIDE AIR INTAKE HOOD 38 1/ 8 CONDENSATE DRAIN PAN EXHAUST NOTES: 1. Carrier recommends a minimum of 2 to -in. of service clearance on all sides of unit except for the control panel side, which should have at least 8-in. clearance. Top should be unobstructed. 2. Dimensions are in inches. a62-69 10

UNIT DIMENSION PRINT 62DA,DB22-38 STANDARD UNIT TOP VIEW 33 3/ 1 TYP. 2 13/16 96 SUPPLY 62 1/ 10 7/8 0 30 17 62 3/8 6 1/2 CUT ALONG DOTTED LINE CUT ALONG DOTTED LINE POWER THROUGH THE CURB SIDE VIEW (HORIZONTAL SUPPLY) 3 1/2 30 1/2 0 1/2 1/2 1/2 18 1/2 a62-70 SUPPLY FAN 83 112 9/16 131 62 /8 8 18 1/2 CONTROL PANEL FILTER ACCESS CONDENSATE DRAIN PAN FRONT VIEW OUTSIDE AIR INTAKE HOOD NOTES: 1. Carrier recommends a minimum of 2 to -in. of service clearance on all sides of unit except for the control panel side, which should have at least 8-in. clearance. Top should be unobstructed. 2. Dimensions are in inches. 11

UNIT DIMENSION PRINT 62DC,DD,DE,DF22-38 UNIT WITH OPTIONAL EXHAUST 1 TYP. 33 3/ 96 62 1/ 10 7/8 2 7/8 1/16 30 2 1/16 2 SUPPLY RETURN 0 0 62 3/8 17 6 1/2 7/8 TOP VIEW POWER THROUGH THE CURB 1 3/8 2 1/ 112 1/2 16 3/ 3 1/ SIDE VIEW (HORIZONTAL SUPPLY) SUPPLY FAN CONTROL PANEL FILTER ACCESS 3 1/2 OUTSIDE AIR INTAKE HOOD 30 1/2 0 1/2 18 1/2 83 FRONT VIEW 1/2 1/2 62 /8 8 CONDENSATE DRAIN PAN EXHAUST NOTES: 1. Carrier recommends a minimum of 2 to -in. of service clearance on all sides of unit except for the control panel side, which should have at least 8-in. clearance. Top should be unobstructed. 2. Dimensions are in inches. a62-71 12

UNIT DIMENSION PRINT 62DC,DD,DE,DF22-38 UNIT WITH OPTIONAL ENERGY CONSERVATION WHEEL 33 3/ 1 TYP. 96 62 1/ 2 13/16 1/16 10 7/8 30 SUPPLY 2 1/16 2 0 0 TOP VIEW CUT ALONG DOTTED LINE CUT ALONG DOTTED LINE SIDE VIEW (HORIZONTAL SUPPLY) 3 1/2 POWER THROUGH THE CURB 0 1/2 30 1/2 1/2 1/2 18 1/2 A62-72 SUPPLY FAN 17 6 1/2 63 1/2 83 1 /8 CONTROL PANEL 3 1/ 170 3/ 62 /8 RETURN 7/8 8 1 3/8 3 3/16 FILTER ACCESS CONDENSATE DRAIN PAN ENERGY RECOVERY WHEEL OUTSIDE AIR INTAKE HOOD FRONT VIEW EXHAUST NOTES: 1. Carrier recommends a minimum of 2 to -in. of service clearance on all sides of unit except for the control panel side, which should have at least 8-in. clearance. Top should be unobstructed. 2. Dimensions are in inches. 13

ACCESSORY DIMENSION PRINT 62DA,DB,DC,DD,DE,DF07-20 UNITS 1-in. ACCESSORY ROOF CURB (FULLY ASSEMBLED) 8 1/2 EQUIPMENT RAIL SUPPORT (REFERENCE DIMENSIONS) EQUIPMENT RAIL SUPPORT 2 TYP. 37 3/ SOLID BOTTOM SPOT WELDED EVERY 6" ALL FOUR SIDES 79 REF. 6 27 3/32 0 3/32 2 1" FIBERGLASS INSULATION SOLID BOTTOM SPOT WELDED EVERY 6" ALL FOUR SIDES 6 1/2 16 1/2 1" FIBERGLASS INSULATION ON BOTH SIDES. 1" FIBERGLASS INSULATION 2 1/ TYP. 1 NOTE: Dimensions are in inches. a62-0 2-in. ACCESSORY ROOF CURB (FULLY ASSEMBLED) 18 1/2 EQUIPMENT RAIL SUPPORT 2 TYP. 79 REF. 37 3/ INSULATED SOLID BOTTOM SPOT WELDED EVERY 6" ALL FOUR SIDES EQUIPMENT RAIL SUPPORT 1" FIBERGLASS INSULATION 6 27 3/32 0 3/32 2 INSULATED SOLID BOTTOM SPOT WELDED EVERY 6" ALL FOUR SIDES 6 1/2 16 1/2 1" FIBERGLASS INSULATION 2 1/ TYP. 1" FIBERGLASS INSULATION ON BOTH SIDES. 2 NOTE: Dimensions are in inches. 1

ACCESSORY DIMENSION PRINT 62DA,DB,DC,DD,DE,DF07-20 UNITS 1-in. ACCESSORY ROOF CURB (FIELD ASSEMBLED) Curb End Utility Channel Gasket Nail Counter Flashing Return 20 1/2" 1/2" Curb Side Rigid Insulation Roofing Felt Cant Strip 7 3/" 2 1/2" Supply 0 1/8" CUT ALONG DOTTED LINE CUT ALONG DOTTED LINE a62-9 Rigid Insulation A30-3 Gasket Nail Roofing Material Equipment Support (Screw 2 Parts Together) 1 3/" 2-in. ACCESSORY ROOF CURB (FIELD ASSEMBLED) Counter Flashing Roofing Felt Cant Strip Roofing Material Return Equipment Support (Screw 2 Parts Together) 20 1/2" 7 3/" Gasket NOTE: Dimensions are in inches. Curb End 1/2" 1 3/" 2 1/2" Supply Utility Channel Curb Side 0 1/8" Gasket NOTE: Dimensions are in inches. 1

ACCESSORY DIMENSION PRINT 62DA,DB,DC,DD,DE,DF22-38 UNITS 1-in. ACCESSORY ROOF CURB (FULLY ASSEMBLED) EQUIPMENT RAIL SUPPORT 8 1/2 2 TYP. 33 109 REF. EQUIPMENT RAIL SUPPORT 1" FIBERGLASS INSULATION INSULATED SOLID BOTTOM SPOT WELDED EVERY 6" ALL FOUR SIDES 8 13/16 13/16 8 6 7/16 16 1/2 38 1/2 1" FIBERGLASS INSULATION ON BOTH SIDES. 1" FIBERGLASS INSULATION 2 1/ TYP. 1 NOTE: Dimensions are in inches. a62-06 2-in. ACCESSORY ROOF CURB (FULLY ASSEMBLED) 18 1/2 EQUIPMENT RAIL SUPPORT 2 TYP. 33 109 REF. INSULATED SOLID BOTTOM SPOT WELDED EVERY 6" ALL FOUR SIDES EQUIPMENT RAIL SUPPORT 8 13/16 13/16 8 1" FIBERGLASS INSULATION INSULATED SOLID BOTTOM SPOT WELDED EVERY 6" ALL FOUR SIDES 6 7/16 16 1/2 38 1/2 1" FIBERGLASS INSULATION 1" FIBERGLASS INSULATION ON BOTH SIDES. 2 2 1/ TYP. NOTE: Dimensions are in inches. 16

ACCESSORY DIMENSION PRINT 62DA,DB,DC,DD,DE,DF22-38 UNITS 1-in. ACCESSORY ROOF CURB (FIELD ASSEMBLED) Return 2 1/2" Utility Channel Curb Side Gasket Nail Counter Flashing 10 3/" Supply 38 1/2" 7/8" Rigid Insulation Roofing Felt Cant Strip Roofing Material 37" Equipment Support (Screw 2 Parts Together) Gasket CUT ALONG DOTTED LINE CUT ALONG DOTTED LINE a62-0 Equipment Support (Screw 2 Parts Together) A62- Return 2-in. ACCESSORY ROOF CURB (FIELD ASSEMBLED) 10 3/" 2 1/2" 37" Utility Channel Supply 38 1/2" Gasket Curb Side 7/8" Rigid Insulation NOTE: Dimensions are in inches. Gasket Nail Counter Flashing Roofing Felt Cant Strip Roofing Material NOTE: Dimensions are in inches. 17