Clock Radio Instruction Manual M102K M102W -AU -AU
SAFETY INFORMATION CONTINUED.. CONTENTS The carton should contain: 1xClock Radio with Mirror Finishing 1xInstruction Manual 1xWarranty card LOCATION.
Display and Controls LED DISPLAY 1 PM ALARM1 4 FM ALARM2 2 3 CONTROLS AND CONNECTION 5 6 7 8 9 10 1.PM 2.FM 3.ALARM2 4.ALARM1 5.FM Aerial 6.Clock Set Button 7.Alarm Set Button 8.Reset Hole 12 13 14 15 16 9.Tune Up/adjust Up Button 10.Tune Down/adjust Down Button 11.Power Cord 12.Radio Button 13.Sleep Button 14.Snooze Button 15.Alarm Mode Switch 16.Volume Control 3
Basic Operation FITTING BACKUP BATTERY You can insert a battery(not supplied) into your clock radio to retain clock and alarm settings in the event of a power cut. If the radio loses the time setting during a power cut,the battery may need to be replaced. Fitting/replacing a battery: 1. Press the catch on the battery cover. 2. While holding the catch, lift the cover of the battery compartment. 3. If a battery is fitted, remove the battery from the battery compartment and unclip the connector from the top of the battery. 4. Replace the battery with the same type 6F22 006P,observing polarity when fitting the connector. 5. Re-fit the cover. BATTER DISPOSAL Dispose of used batteries with regard to the recycling regulations in your area. Do not Short circuit batteries or throw them into water, the general rubbish or in a fire. Weak batteries can leak and damage the unit. Replace them in good time! Carefully unpack the unit. If it is damaged, please return it to your nearest store for replacement. Remember to take your purchase receipt with you. Retain the User Handbook. If you pass the unit on to a third party make sure you pass on the handbook. We suggest you retain the packaging for any recycling regulations in your area. 4
Basic Operation GETTING STARTED Before connecting the power, check that the main voltage on the rating plate under the radio is the same as the voltage in your area. Plug the AC power cord into the wall socket and switch the main power on,the unit is now ready for use. SETTING THE CLOCK The clock is set manually. The clock displays the time in 24 hour format (for example,2a.m.is displayed as 2:00,2p.m.is displayed as 14:00). When setting the time or alarm, ensure that you are setting times in this format. 1.Press the set button, the hour digits will flash. 2.Press the or button to set the hour digits to the correct time. 3.Press the set button again, the minute digit will flash. 4.Now press the or button to set the minutes digits to the correct timer. 5.Press the set button again,the clock is now set. NOTE: If you prefer, you can hold down the or button when setting the time. Then hour or minute setting will automatically change. If a backup battery is fitted, the clock and alarm settings will be retained in the event of a power cut. LISTENING TO THE RADIO Before using your clock radio for FM reception, unwrap and fully extend the aerial wire. You may need to adjust the position of the aerial wire for maximum signal strength. 1.Press the radio button, the radio will be switched on and the tuning frequency will be displayed. 2.Press the radio button, the radio will be switched off. 3.Press and hold the or button for three seconds to search up or down the band for a station. 4.Tuning will stop when the next station is reached and the station will play. Adjust the aerial wire for the clearest reception. 5.Press the or button to tune up or down the band manually in 0.1MHz steps. 6.Turn the volume control to set the volume you want. 5
Basic Operation SETTING THE ALARM TIME The clock provide dual alarm setting,set the Alarm mode switch to the Buzzer or Radio position, depending on your wake-up preference, the alarm indicator will light. NOTE: It is not possible to set the alarm when the Alarm mode switch is set to alarm off. 1.Press the alarm button, the hour digits will flash. 2.Press the or button to set the hour digits to the correct time. 3.Press the alarm button again, the minute digit will flash. 4.Now press the or button to set the minutes digits to the correct time. 5.Press the alarm button again, the alarm1 is now set. 6.Alarm2 can be set after alarm1 setting finish. NOTE: If you have set the radio to wake you up, check that a station is tuned before going to bed and that you have set your preferred wake-up volume. WHEN ALARM SOUNDS The radio will play or the buzzer will sound and the alarm indicator will flash, The alarm will sound for 60 minutes. To stop the alarm sounding, switch the alarm button to off position. SNOOZE MODE Press the SNOOZE button to set snooze mode. The alarm will stop sounding and will sound again after a 9 minute period. RESET In the unlikely event that your clock is not operating correctly, try resetting it to clear the problem. Use the end of a paper-clip or similar to press the reset button inside the reset hole. The clock will reset. Set the time and alarm etc. SLEEP When listening to the radio, you can select Sleep mode to play for a set period of time while you are going to sleep. press the Sleep button repeatedly to choose your preferred sleep time in the range of 15-120minutes. The radio will switch off automatically after playing for the sleep time you set. Press the Sleep button repeatedly until the sleep time not display. SPECIFICATION Power supply:...ac 240V~,50Hz Power consumption...4w Backup battery...9v (6F22 006P) Frequency range(fm):...87.5-108mhz Weight:...330g Class ll construction double insulated. This product must not be connected to earth. 6
MD120702-01