Application Tooling. Effective February Compression Connectors and Tools. Terminal Products and Tools

Application Tooling Compression Connectors and Tools Terminal Products and Tools Insulation Piercing Connectors Grounding Connectors Cable Fastening Systems Wiring Duct and Accessories Wire and Connector Insulation Products Effective February 2007

Since the 1930s, Thomas & Betts has been supplying tools, dies and connectors. Today, with more than 75 years experience in tools, dies and connectors, Thomas & Betts still sets the standard for innovation, quality and performance for application tooling. Rely on Thomas & Betts tools for labor-saving features, user comfort and convenience, long service life and extraordinary value. For more than 40 years, Thomas & Betts highly trained, experienced and dedicated staff has been supporting customers in every aspect of their tooling needs. With 100-plus years of combined experience, T&B application tool specialists are ready to assist you with: Tool recommendations based on your application and workload Demonstrations Rental and leasing programs On-site installation On-site training Technical support Calibration and certification (factory or on-site) Repair (both warranty and non-warranty) Loaners for temporary use during repairs Supplying components and technical documentation for customer-performed repairs You can choose Thomas & Betts tools with confidence, because we stand behind them with our warranty. The chart below shows the standard length of warranty for different types of tools. See the inside back cover for additional warranty details. 1 Year Cable Tie Installation Tools Printers Cable Cutters & Strippers Dies 2 Years Mechanical Hand Tools with Shure-Stake Mechanism Pneumatic Tools Hydraulic Pumps Battery-Operated Tools 5 Years Mechanical Hand Tools without Shure-Stake Mechanism Hydraulic Tools (self-contained and remote heads) Call Toll-Free 1-800-284-TOOL (8665) For more information about Thomas & Betts : E-Mail us at toolservice@tnb.com.

Contents Thomas & Betts repairs all Thomas & Betts tools, from simple hand tools to hydraulic pumps and crimping heads. performs all warranty repairs and can supply you with a temporary loaner tool when necessary. can also perform non-warranty repairs, or, if you wish to repair your own tools, contact to obtain any needed components, technical documentation and support. For short-term installation projects, sometimes it makes more sense to rent than buy power tools. Thomas & Betts understands this and has created a Tool Rental Program, geared specifically for contractors and projects, to meet the need. Renting T&B tools is easy. A rental agreement is available on our web site, and you can pay the rental fee by credit card. Call at 1-800-284-TOOL (8665) for more details, including a list of Thomas & Betts tools available for rental. For longer term use, many OEMs find that leasing high-end tools may be more financially attractive than purchasing. Call at 1-800- 284-TOOL (8665) for more information and a list of Thomas & Betts tools available for lease. Color-Keyed Tools Manual Compression Tools #8 to 250 MCM...2 Manual Compression Tools #8 to 500 MCM...3 Power-Assisted Compression Tools #8 to 600 MCM...4 5 Power-Assisted Compression Tools #8 to 750 MCM...5 Power-Assisted Compression Tools #8 to 900 MCM...7 9 Power-Assisted Compression Tools #8 to 1500 MCM...10 Hydraulic Pumps...11 13 Battery Connector Tools...13 Strippers, Cutters and Other Tools...14 17 Crimping Dies...18 21 Sta-Kon Tools Stripping/Cutting Tools...22 Plier-Type Hand Crimp Tools...23 Comfort Crimp Hand Tools...24 Ratchet-Type Hand Crimp Tools...25 Toggle-Type Hand Crimp Tools...26 Pneumatic Crimp Tools...27 Battery-Powered Crimp Tools...28 Hydraulic Crimp Tools...29 31 Hydraulic Pumps...32 Crimping Dies...33 35 Dragon Tooth Tools Manual Crimp Tools...36 Battery-Operated Crimp Tools...36 Hydraulic Crimp Tools...37 38 Hydraulic Pumps...39 Crimping Dies...39 Shield-Kon Tools Hand Crimp Tools...40 Crimping Dies...41 Hydraulic Crimp Head...41 Ty-Rap Tools Cable Tie Installation Tools...42 44 Ty-Duct Tools Cutting Tools...45 46 Notching Tool...46 Rivet Installation Tool...46 Shrink-Kon Tools Torches and Heat Guns...47 Product Index...48 1

Mechanical Compression Tools: #8 to 250 MCM TBM25S Crimp Tool Wide range of #8 to #2 for copper lugs and #10 to #6 for aluminum lugs Each die has die code embossing Shure-Stake mechanism ensures a properly completed crimp each time Color-coded die wheel rotates into position for proper die nest Also installs up to green color-coded C-taps and MD2 Series motor disconnects Requires two crimps per connector TBM4S Dieless Crimp Tool TBM25S Creates Diamondstyle crimp Crimp tool with Shure-Stake mechanism for #8 #2 copper and #10 #6 aluminum 1 Creates Indentstyle crimp Wide range of #8 to 250 kcmil for copper lugs and #8 to 4/0 for aluminum lugs Adjustable indenter eliminates the need to buy and maintain numerous individual dies Shure-Stake mechanism ensures a properly completed crimp each time Easily adjusted by turning knurled adjusting wheel and aligning pointer with proper terminal size Dieless, adjustable crimper for Color-Keyed compression connectors TBM4S Dieless crimp tool with Shure-Stake mechanism for #8 250 kcmil copper and #8 4/0 aluminum 1 TBM5S Crimp Tool Creates Diamondstyle crimp Wide range of #8 to 250 kcmil for copper and #10 to 4/0 for aluminum lugs and splices Also installs C-taps from 54705 to 54750 Shure-Stake mechanism ensures a properly completed crimp each time Includes color-coded, die-code-embossed installation dies CAT. NO. COLOR CODE DIE CAT. NO. PKG. QTY. RED BLUE 13454 GRAY BROWN GREEN PINK 13455 BLACK TBM5S ORANGE 1 PURPLE 13456 YELLOW GOLD TAN 13457 OLIVE RUBY WHITE 13458 2

Mechanical Compression Tools: #8 to 500 MCM TBM6S Crimp Tool Creates Diamondstyle crimp Wide ranges of #8 thru 500 kcmil for copper lugs, splices and taps and #10 thru 350 kcmil for aluminum lugs and splices Also installs 63105 through 63140 orange, green and blue H-taps Shure-Stake mechanism ensures a properly completed crimp each time Comes complete with plastic carrying case and wire brush COLOR CAT. NO. CAT. NO. CAT. NO. CODE UPPER DIE LOWER DIE PKG. QTY. RED 13475 13477 BLUE 13475 13477 GRAY 13472 13476 BROWN 13474 13477 GREEN 13474 13477 PINK 13475 13477 BLACK 13474 13477 ORANGE 13474 13477 TBM6S PURPLE 13475 13477 1 YELLOW 13473 13476 GOLD 13474 13477 TAN 13474 13477 OLIVE 13475 13477 RUBY 13473 13476 WHITE 13473 13476 RED 13472 13476 BLUE 13472 13476 Carrying Cases for TBM5S and TBM6S 295-31365M Steel Carrying Case for TBM5S and TBM6S 1 295-31365 Plastic Carrying Case for TBM5S and TBM6S 1 TBM8S Crimp Tool Creates Diamondstyle crimp Installs code copper lugs and connectors #8 through 500 kcmil Installs aluminum lugs and connectors #10 through 350 kcmil Shure-Stake mechanism ensures positive compression Included dies are color-coded and provide die-code embossing for easy installation and inspection Installs all code copper compression joints and small C-taps Comes complete with installing dies and wire brush in plastic carrying case COLOR DIE CAT. NO. CODE CAT. NO. PKG. QTY. RED BLUE 13461 GRAY BROWN GREEN PINK BLACK 13462 TBM8S ORANGE PURPLE YELLOW 13463 1 GOLD TAN OLIVE 13464 RUBY WHITE 13465 RED 13466 BLUE 13467 BROWN 13468 3

Power-Assisted Compression Tools: #8 to 500 MCM 25000 Air-Operated Bench- Mount Crimp Tool Creates Diamondstyle crimp Installs copper and aluminum connectors on wire sizes from 8 AWG to 500 kcmil Compact, heavy-duty air tool Simple to operate just insert stripped wire into connector barrel, position it in crimping nest and depress foot pedal to actuate crimping dies Uses same crimping dies as TBM6S (see p. 3) 25000 Air-Operated Bench-Mount Crimp Tool 1 Battpac LT BPLT62BSCR/ BPLT62500BSCR 6-Ton Compression Tools NEW! Ergonomic design and reduced weight for operator comfort New double-speed feature decreases crimp time by doubling jaw speed until it reaches load New, more powerful Ni-MH battery has 50% more energy and less memory effect than old batteries Rotating head allows maximum flexibility for crimping Uses TBM62 Series dies Creates Hexstyle crimp Installing Range: Up to 500 mcm copper lugs & splices Up to 350 mcm aluminum lugs & splices 54705 to 54750 C-taps Output Force: 6 tons Dimensions (L x W x H): 11" x 3 3 4" x 11 7 8" Battery: Ni-MH 14.4V 3.0Ah Weight with Battery: 8 lbs. BPLT62BSCR Battpac LT Tool Kit. Includes tool, two batteries, charger, 1 shoulder strap, wrist strap, carrying case (no dies). BPLT62500BSCR Complete Battpac LT Tool Kit with dies TBM6221 through TBM6287. 1 4

Power-Assisted Compression Tools: #8 to 600 MCM Battpac LT BPLT6BSCR 6-Ton Compression Tool NEW! Open yoke design allows for maximum crimping flexibility New double-speed feature decreases crimp time by doubling jaw speed until it reaches load New, more powerful Ni-MH battery has 50% more energy and less memory effect than old batteries Uses 6-TON Series dies and Blackburn "O" and "D" Series dies Creates Hexstyle crimp Installing Range: Up to 600 mcm copper lugs & splices Up to 400 mcm aluminum lugs & splices CHT814-10 to CHT214-9 copper H-taps 63105 to 63148 aluminum H-taps 54705 to 54750 C-taps Output Force: 6 tons Dimensions (L x W x H): 11" x 3 3 4" x 11 7 8" Battery: Ni-MH 14.4V 3.0Ah Weight with Battery: 8 lbs. BPLT6BSCR Battpac LT Tool Kit. Includes tool, two batteries, charger, 1 shoulder strap, carrying case (no dies) TBM6H 6-Ton Hydraulic Crimping Head Lightweight design weighs less than 7 lbs., including dies Embosses die code on connection for easy inspection Uses 6-TON Series and Blackburn "O" and "D" Series dies color-coded for easy matching with Color-Keyed connectors Installing Range: Up to 600 mcm copper lugs & splices Up to 400 mcm aluminum lugs & splices CHT814-10 to CHT214-9 copper H-taps 63105 to 63148 aluminum H-taps 54705 to 54750 C-taps Output Force: 6 tons Operating Pressure: 10,000 psi nominal Dimensions (L x W x H): 12" x 2 1 4" x 3 9 16" Weight without Dies: 6.5 lbs. Creates Hexstyle crimp TBM6H 6-Ton Hydraulic Head with Steel Case 1 TBM6HD-1 Die Set for #8 thru 500 kcmil (6-TON21 thru 6-TON87) 1 5

Power-Assisted Compression Tools: #8 to 750 MCM, #8 to 900 MCM JB12B 12-Ton Manual Hydraulic Crimp Tool Self-contained hydraulic crimping tool for copper, aluminum and ASCR connectors Two-stage, rapid-ram advance mechanism for fast installation 180º head rotation Accepts all U-type dies used for Alcoa, Burndy, Thomas & Betts and Blackburn tools of equivalent tonnage Installing Range: Up to 750 mcm copper lugs & splices Up to 650 mcm aluminum lugs & splices CHT814-10 to CHT2502-6 copper H-taps 63105 to 63148 aluminum H-taps 54755 to 54770 C-taps Output Force: 12 tons Dimensions (L x W x H): 22 3 4" x 2 1 2" x 4 7 8" Weight without Dies: 13 lbs. Creates Hexstyle crimp JB12B 12-Ton Manual Hydraulic Crimp Tool 1 with Carrying Case TBM12 12-Ton Hydraulic Crimp Head 13642M 12-Ton Hydraulic Crimping Head Creates Hexstyle crimp Rugged steel construction is durable for most applications Includes five sets of multi-nested dies Uses TBM12D style dies Installing Range: Up to 900 mcm copper lugs & splices Up to 750 mcm aluminum lugs & splices 54755 to 54775 C-taps Creates Hexstyle crimp Dies emboss die code on connectors for easy inspection Closed yoke design yields maximum crimp performance Output Force: 12 tons Operating Pressure: 10,000 psi nominal Dimensions (L x W x H): 14 1 4" x 2 1 2" x 3 7 8" Weight without Dies: 9 lbs. TBM12 12-ton Hydraulic Head with Steel Case 1 If using old style 11700 Series Die Set, use adapter, Cat. No. TBM12D-AR (not included) for adaptation to the above tool. Order adapter separately. Rugged steel construction is durable for most applications Used for Color-Keyed and Sta-Kon connectors The only military-listed hydraulic head (Mil. Spec. MS25441-1) Uses 11700 Series dies for Color-Keyed connectors; see Sta-Kon section for Sta-Kon dies Installing Range: Up to 900 mcm copper lugs & splices Up to 750 mcm aluminum lugs & splices 54755 to 54775 C-taps Output Force: 12 tons Operating Pressure: 10,000 psi nominal Dimensions (L x W x H): 14 1 2" x 2 1 2" x 3 15 16" Weight without Dies: 9 lbs. 13642M 12-ton Hydraulic Head with Steel Case 1 6

Power-Assisted Compression Tools: #8 to 900 MCM SMART Tools Tool is smart because it requires no dies Automatically compresses to the correct depth based on size of connector in jaws C-type head swivels 90º for easy crimp positioning Forged steel construction is well suited for both field and bench work Installs both Color-Keyed and non-insulated Sta-Kon connectors How the SMART Tool Works The SMART Tool was engineered with built-in intelligence* that enables it to sense the connector barrel diameter and automatically apply just the right amount of compression force. This eliminates virtually all air spaces and forms the connector and conductor strands into a solid mass, resulting in a high-quality, low-resistance connection. In addition, the tool clearly embosses T&B with each compression for positive verification that the correct tool was used. * System Novopress Uniform, Dependable Connections The SMART Tool gives you consistent, high-quality compression connections over a wide range of connector sizes. Available in manual, battery-powered and air-operated versions, this tool easily installs lugs and splices from #8 AWG through 900 mcm copper or 750 mcm aluminum without changing dies. For the specified wire range, all you need is one tool. You always have the right die size, eliminating die-selection mistakes. Lower Installation Costs Productivity will be greatly improved with the SMART Tool, especially when installing a variety of connector sizes or types. Initial investment is low, requiring minimal tool inventory. These benefits add up to lower installed cost. C-Type Yoke Offers Installation Convenience The C-type yoke configuration and large die spacing enable the SMART Tool to slip directly over the connector. This means added speed and convenience when installing two-way splice connectors, especially in confined spaces. SMART Tool Range Taking Features The following size Color-Keyed lugs and splice connectors, when crimped with the SMART Tools, produce these range taking capabilities: COPPER ALUMINUM STANDARD RANGE STANDARD RANGE WIRE SIZE TAKING WIRE SIZE TAKING 1/0-AWG #6-1/0 AWG 1/0-AWG #6-1/0 AWG 2/0-AWG #1-2/0 AWG 2/0-AWG #1-2/0 AWG 4/0-AWG #2-4/0 AWG 4/0-AWG #2-4/0 AWG 300 kcmil #2/0-300 kcmil 300 kcmil #2/0-300 kcmil 350 kcmil 250-350 kcmil 350 kcmil 250-350 kcmil 500 kcmil 250-500 kcmil 500 kcmil 4/0-500 kcmil 750 kcmil 500-750 kcmil 750 kcmil 500-750 kcmil TBM8-750M-1 12-Ton Dieless Manual Hydraulic Tool Creates Indentstyle crimp Installing Range: Up to 900 mcm copper lugs & splices Up to 750 mcm aluminum lugs & splices Output Force: 12 tons Dimensions (L x W): 21 1 2" x 4 7 32" Weight: 13 lbs. TBM8-750M-1 12-Ton Dieless Manual Hydraulic Compression Tool 1 Battpac LT TBM8-750BSCR 12-Ton Dieless Battery- Powered Tool Creates Indentstyle crimp Installing Range: Up to 900 mcm copper lugs & splices Up to 750 mcm aluminum lugs & splices Output Force: 12 tons Dimensions (L x W x H): 19 1 2" x 3 7 8" x 8 1 2" Battery: Ni-MH 14.4V 3.0Ah Weight with Battery: 9 lbs. TBM8-750BSCR Battpac LT 12-Ton Dieless Battery-Powered 1 Compression Tool. Includes carrying case, charger, two batteries and carry strap. TBM8-750 12-Ton Dieless Hydraulic Head Creates Indentstyle crimp....... Specifications....... Installing Range: Up to 900 mcm copper lugs & splices Up to 750 mcm aluminum lugs & splices Output Force: 12 tons Operating Pressure: 10,000 psi nominal Dimensions (L x W x H): 14 1 2" x 4 7 32" x 2 9 16" Weight: 9 lbs. TBM8-750 12-Ton Dieless Hydraulic Compression Head 1 7

Power-Assisted Compression Tools: #8 to 900 MCM TBM14M 14-Ton Manual Hydraulic Crimp Tool Features short fiberglass handles for insulation and ease of use in tight spaces Two-stage pump provides rapid advance for fast installation Uses standard T&B Color-Keyed 15500 Series dies Creates Hexstyle crimp Installing Range: Up to 900 mcm copper lugs & splices Up to 750 mcm aluminum lugs & splices CHT814-10 to CHT2502-6 copper H-taps 63105 to 63148 aluminum H-taps 54755 to 54775 C-taps Output Force: 14 tons Length: 24" Weight without Dies: 15.4 lbs. TBM14M 14-ton manual hydraulic crimp tool with case 1 TBM14MC 14-Ton Compact Manual Hydraulic Crimp Tool NEW! Improved ergonomic design requires less force 180º rotating head for use in tight spaces 1.65" jaw opening accommodates large compression terminals and joints Dual-speed action pump offers fast advancing speed for approach of die to connector and slower, more powerful speed for crimping Creates Hexstyle crimp Installing Range: Up to 900 mcm copper lugs & splices Up to 750 mcm aluminum lugs & splices CHT814-10 to CHT2502-6 copper H-taps 63105 to 63148 aluminum H-taps 54755 to 54775 C-taps Output Force: 14 tons Length: 20 1 2" Weight without Dies: 14 lbs. Built-in safety valve bypasses oil supply at maximum pressure Pressure-release system can be easy activated at any stage of compression Uses standard T&B Color-Keyed 15500 Series dies TBM14MC 14-ton compact hydraulic crimp tool 1 8

Power-Assisted Compression Tools: #8 to 900 MCM Battpac LT BPLT14BSCR/BPLT14BSCRI 14-Ton Battery-Powered Compression Tools BPLT14BSCR Reduced weight and more ergonomic design New double-speed feature decreases crimp time by doubling jaw speed until it reaches load New more powerful Ni-MH battery has 50% more energy and less memory effect than old batteries Rotating head allows maximum flexibility for crimping Uses Standard T&B Color-Keyed 15500 Series dies Creates Hexstyle crimp Installing Range: Up to 900 mcm copper lugs & splices Up to 750 mcm aluminum lugs & splices CHT814-10 to CHT2502-6 copper H-taps 63105 to 63148 aluminum H-taps 54755 to 54775 C-taps Output Force: 14 tons Dimensions (L x W x H): 18 1 8" x 3 7 8" x 10" Battery: Ni-MH 14.4V 3.0Ah Weight with Battery: 18.1 lbs. BPLT14BSCRI BPLT14BSCR Battpac LT 14-Ton Compression Tool. Includes carrying case, charger, two-batteries, carry strap 1 BPLT14BSCRI Same as above, but insulated head 1 13100A 14-Ton Hydraulic Crimping Head Rugged design, made to last in field or on bench C-yoke provides maximum flexibility for crimping Uses standard T&B Color-Keyed 15500 Series dies Operates on 10,000 psi hydraulic pumps Creates Hexstyle crimp Installing Range: Up to 900 mcm copper lugs & splices Up to 750 mcm aluminum lugs & splices CHT814-10 to CHT2502-6 copper H-taps 63105 to 63148 aluminum H-taps 54755 to 54775 C-taps Output Force: 14 tons Operating Pressure: 10,000 psi nominal Dimensions (L x W x H): 11 1 2" x 2 1 2" x 4 1 4" Weight without Dies: 10 lbs. 13100A 14-ton hydraulic head with steel case 1 9

Power-Assisted Compression Tools: #8 to 1500 or 2000 MCM Battpac LT BPLT15BSCR 15-Ton Battery-Powered Compression Tool Ergonomic design and reduced weight for operator comfort New double-speed feature decreases crimp time by doubling jaw speed until it reaches load New, more powerful Ni-MH battery has 50% more energy and less memory effect than older batteries Rotating head allows maximum flexibility for crimping Uses 15600 Series dies; can also use 15500 Series dies with 15500-TB adapter Installing Range: 54755 to 54790 C-taps Up to 1500 mcm copper Output Force: 15 tons lugs & splices Dimensions (L x W x H): Up to 1000 mcm aluminum 21" x 3 1 2" x 11" lugs & splices Battery: Ni-MH 14.4V 3.0Ah CHT814-10 to CHT750-350-1F Weight with Battery: 23.75 lbs. copper H-taps 63105 to 63180 aluminum H-taps TBM15I 15-Ton Hydraulic Crimping Head Creates hexstyle crimp Head made of forged steel and insulated with rubber boot Longer, slimmer design enables easier access into tight spaces, such as in cable tray and central office applications Wider jaw opening eases crimping of larger lugs, C-taps and H-taps Uses 15600 Series dies; can also use 15500 Series dies with 15500-TB adapter Creates hexstyle crimp Cat. No. DESCRIPTION PKG. QTY. BPLT15BSCR 15-Ton Battery-Powered Compression Tool 1 Includes carrying case, charger, 2 batteries and carry strap Installing Range: Up to 1500 mcm copper lugs & splices Up to 1000 mcm aluminum lugs & splices CHT814-10 to CHT750-350-1F copper H-taps 63105 to 36180 aluminum H-taps 54755 to 54790 C-taps Output Force: 15 tons Operating Pressure: 10,000 psi nominal Dimensions (L x W x H): 15 3 4" x 2 5 8" x 4 3 8" Weight without Dies: 16.5 lbs. TBM15I Insulated 15-Ton Hydraulic Head with Steel Case 1 15600 Series Fits directly into tool for larger size connectors, 800 kcmil 1,500 kcmil 15500 Series Used in conjunction with 15500-TB Adapter, #8 AWG 750 kcmil 21940 40-Ton Hydraulic Crimping Head Creates hexstyle crimp Compact design delivers maximum pressure for larger lugs and splices Ideal for applications requiring larger lugs up to 2000 mcm Uses 11300 and 11400 Series dies Installing Range: Up to 2000 mcm copper lugs & splices Up to 2000 mcm aluminum lugs & splices Output Force: 40 tons Operating Pressure: 10,000 psi nominal Dimensions (L x W x H): 12" x 4 3 4" x 7 3 8" Weight without Dies: 40 lbs. 21940 40-Ton Hydraulic Head with Steel Case 1 10

Hydraulic Pumps 13606 Foot-/Hand-Operated and 13604 Hand-Operated Hydraulic Pump 13606 operates with either foot or hand; 13604 is hand operated only Operates all T&B hydraulic heads Nominal Pressure: 9,800 psi Pumping Capacity: 2.6 cu. in./min. @ 200 psi 0.16 cu. in./min. @ 10,000 psi Reservoir Volume: 125 cu.in. (0.54 gal.) Built-in safety bypass valve Factory set at 9,800 psi Max. Handle Force: 130 lbs. Dimensions (L x W x H): 23" x 5 3 4" x 6 3 4" Weight: 29 lbs. 13606 Foot-/Hand-Operated Hydraulic Pump 13606 Combination Hand or Foot-Operated Hydraulic Pump 1 13604 Hand-Operated Hydraulic Pump 1 Battpac LT BPLT13970P2 Pump Small and lightweight 60 minutes full recharge Highly visible display indicates battery power level Socket for 24 VDC external connection Operation in any position: on its side or upright Separate operation/release buttons protect against accidental operation Energy consumption limited by automatic shut-off Easily accessible oil top-up inlet................. Specifications.................. Nominal Pressure: 10,000 psi Pumping Capacity: 30 cu.in./min. Reservoir Volume: 60 cu.in. (.26 gal.) Dimensions (L x W x H): 13 1 2" x 6 1 2" x 12 3 4" Battery: Ni-MH 24V, 3 Ah Weight with Battery: 20.9 lbs. Battery Performance Guide In tests, the number of crimps obtained from a fully charged battery, using a remote crimping head, was: 102 crimps for Cu connectors on 250 kcmil HD Cu conductor 98 crimps for C-Tap connectors on #2 AWG HD Cu conductor 76 crimps for Cu sleeve connectors on 500 kcmil HD Cu conductor BPLT13970P2 Battpac LT Pump includes canvas accessories carrying 1 bag, carrying strap, remote hand controller, two batteries, battery charger and non-drip couplings BPLT13970RB Ni-MH 24V Replacement battery 1 BPLT13970RP Canvas backpack for pump 1 BPLT13970DC Power connecting cable with clips 1 BPLT13970FS Remote foot pedal controller 1 11

Hydraulic Pumps 13600 Electric Hydraulic Pump Designed for use with single-acting cylinders and tools rated for 10,000 psi operation Supplied with metal carrying case 13620 hand switch and 13619 hydraulic hose, both sold separately, required for operation 13600 Electric Hydraulic Pump hand or foot switch and 1 non-metallic hose (sold separately) required for operation You may also need 13620 Hand Switch 10 ft. 1 13589A Foot Switch 10 ft. 1 13619 10 ft. Non-Metallic Hose 1 13618 20 ft. Non-Metallic Hose 1 13600S Sled type stand for 13600 pump 1..... Specifications...... Motor: 1 2 hp, 115V 50 60 Hz 10 amps Pumping Capacity: 170 cu. in./min. at 100 psi 32 cu. in./min. at 1,000 psi 25 cu. in./min. at 5,000 psi 18 cu. in./min. at 10,000 psi Reservoir Volume: 104 cu. in. (.45 gal.) Basic Pump Dimension: 6" x 8" x 16" Weight: 25 lbs. 13610A Electric Hydraulic Pump with Shure-Stake Control Shure-Stake control mechanism requires 9,800 psi pump pressure before recyling to prevent under-crimping Designed for use with single-acting cylinders and tools rated for 10,000 psi operation Supplied with metal carrying case Motor Rating: 1 2 hp, 115V, 50-60 Hz, 12.5 amps Pumping Capacity: 170 cu. in./min. at 100 psi 32 cu. in./min. at 1,000 psi 25 cu. in./min. at 5,000 psi 18 cu. in./min. at 10,000 psi Reservoir Volume: 104 cu. in. (.45 gal.) Basic Pump Dimension: 8 1 2" x 10 1 2" x 16" Weight: 35 lbs. 13610A Electric Hydraulic Pump with Shure-Stake control 1 hand or foot switch and non-metallic hose (sold separately) required for operation You may also need 13611 Hand Switch 10 ft. 1 13612 Foot Switch 10 ft. 1 13619 10 ft. Non-Metallic Hose 1 13618 20 ft. Non-Metallic Hose 1 12

Hydraulic Pumps and Battery Connector Tools 13810 Heavy-Duty Electric Hydraulic Pump with Shure-Stake Control Designed for perfect crimps every time in heavy-duty OEM applications Heavy-duty OEM two-stage pump with high flow rate Shure-Stake control mechanism requires 9,800 psi pump pressure before recyling to prevent undercrimping Requires hand or foot control (sold separately) Battery Connector Crimp Tools Adjustable die crimping tool for Color-Keyed cast and tubular battery connectors Available with Shure-Stake mechanism to ensure a complete crimp every time (BCT840S) Crimps casting and tubular battery connectors ranging from 4 AWG to 4/0 BCT840, BCT840S Motor Rating: 1 1 2 hp, 115V, 60 Hz, 23 amps Pumping Capacity: 235 cu.in./min. at 200 psi 61 cu.in./min. at 8,000 psi Reservoir Volume: 462 cu.in./2 gal. Dimensions (L x W x H): 10 3 4" x 15" x 20 3 4" Weight: 60 lbs. TBM5SV, TBM5V 13810 Heavy-duty electric hydraulic pump with Shure-Stake 1 control hand or foot switch and non-metallic hose (sold separately) required for operation You may also need 13611 Hand switch 10 ft. 1 13612 Foot switch 10 ft. 1 13619 10 ft. Non-Metallic Hose 1 13618 20 ft. Non-Metallic Hose 1 Heavy-duty crimping tool including die for 8 AWG-4/0 battery connectors, lugs and splices The single die is an integral part of the tool; no dies to lose or misplace Available with Shure-Stake mechanism to ensure a complete crimp every time (TBM5SV) Miscellaneous Hydraulic Pump Accessories 21061 Hydraulic Oil 1 13798 Male Pioneer Quick Disconnect Coupler 1 13799 Female Pioneer Quick Disconnect Coupler 1 13614 Metallic Reinforced Hose for OEM operations 10 ft. 1 BCT840 Dieless Crimp Tool for cast and tubular battery connectors 1 BCT840S Dieless Crimp Tool with Shure-Stake mechanism for cast and tubular battery connectors 1 TBM5V Ratchet Crimp Tool with die for 8 AWG to 4/0 battery connectors 1 TBM5SV Ratchet Crimp Tool with Shure-Stake mechanism and die for 8 AWG to 4/0 battery connectors 1 13

Strippers, Cutters and Other Tools BCS8-40 Cable Stripper 368-CK Cable Stripper BCS8-40 BCS8-40 Cable stripper for 8 AWG-4/0 battery cable with replacement blade provided in the handle 1 368-CK Cable stripper for #1 to 1,000 kcmil 1 364RF/366RF Cable Cutters with Fiberglass Handles CAT. NO. CABLE SIZE PKG. QTY. 364RF Cutter for up to 500 kcmil copper and aluminum 1 366RF Cutter for up to 1,000 kcmil copper and aluminum 1 For copper and aluminum cable only. Not for steel. Replacement blades are available through. TBM40HC Hand-Operated Hydraulic Cutting Tool Specifically designed to cut copper, aluminum and telecommunications cables up to 3.35" O.D. Offers dual-speed action: fast advancing speed for rapid approach of blades to cable and slower, more powerful speed for cutting Blades manufactured from high-strength, heat-treated steel to ensure long service life Head easily opens to enable cutting of existing run cables Head rotates 180º, enabling operator to position for easiest use Automatic safety valve bypasses oil when reaching maximum pressure Pressure release device can also be activated during any point of operation Max. Cutting Capacity: 3.35" O.D. Weight: 14.55 lbs. Dimensions (L x W): 25.69" x 6.89" TBM40HC Hand-operated hydraulic cutting tool 1 14

Strippers, Cutters and Other Tools CSR750 Cable Cutter Battpac LT BPLT54BSCT Fast- Cycle Battery- Powered Cutting Tool Special advance stroke mechanism requires less handle force Cuts copper or aluminum cables up to 750 kcmil Short handles (only 10" long) enable use in tight spaces...... Specifications...... Max. Cutting Capacity: 2 1 8" O.D. Aluminum; 750 kcmil Copper Recommended Cutting Range for Consistent Use: 250 kcmil Batteries: 6.0V Weight with battery: 4.8 lbs. CSR750 Cutter for up to 750 kcmil copper or aluminum 1 Battpac TBM54BSCT and TBM54BSCTS Battery-Powered Cutters Removable battery simply change for continuous use One-handed control of blade advancement and retraction TBM54BSCTS cuts up to 750 kcmil copper, 2 1 8" O.D. aluminum and 636 kcmil ACSR TMB54BSCT cuts up to 1,500 kcmil copper and 2 1 8" O.D. aluminum (not for use on ACSR) Guide to Cutting Cycles This guide indicates the number of cutting cycles that the TBM54BSCT and TBM54BSCTS can be expected to perform when the battery is fully charged. These figures are approximate and will vary according to the charging and other operating conditions, such as temperature, humidity and battery condition. APPROX. CUTTING CYCLES CAT. NO. CONDUCTOR CRCTBPI & CRCTBP CRCTPBEI TBM54BSCTS 750 kcmil Cu 35 105 636 kcmil ACSR 50 150 TBM54BSCT 1,000 kcmil Cu 45 135 1,500 kcmil Cu; 2 1 8" Al 30 90 BPLT54BSCT Motor: 14.4V DC Dimensions (L x W x H): 16" x 4" x 4.5" Weight with Battery: 7.2 lbs. Battpac LT Fast-Cycle Cutting Tool. Includes carrying case, charger, two batteries, carry strap 1 Battery Cartridge: (CRCTBP) Battery Type: Sealed NIckel Cadmium Voltage: 14.4V DC Rated Current: 1.9Ah Dimensions: 3.5"L x 2.7"W x 5.3"H Weight: 1.6 lbs. Battery Charger: (CRCTQC) Input Voltage: 120V AC Single Phase Charging Capacity: 20 VA Charging Time:15 min. CRCTBP & CRCTBPI 45 min. CRCTBPEI Dimensions: 7.5"L x 3.7"W x 3.5"H Weight: 4 lbs. Optional Accessories: Battery Pack: CRCTBPEI Battery Cartridge: CRCTBPI or CRCTBP DC Charger: CRCTDC...... Specifications...... TBM54BSCTS Battery-powered cutter for up to 750 kcmil Cu, 2 1 8" O.D. Al and 636 kcmil ACSR 1 TBM54BSCT Battery-powered cutter for up to 1,500 kcmil Cu, 2 1 8" O.D. Al (not for use on ACSR) 1 15

Strippers, Cutters and Other Tools Battpac TBM58BSCT Battery-Powered Cutter Designed for one-handed operation Simply remove pin latch, place over cable, reinsert pin and cut Built-in bypass pops off if material is beyond cutter s capacity Cuts ACSR, aluminum and copper cables up to 1 1 2", regular guy wires and ground rods up to 5 8" NOTE: Not recommended for use on hardened steel. Standard Battpac Kit Includes: 1 battery-powered tool 1 carrying strap 1 carrying case 2 CRCTBP batteries 1 CRCTQC 15-minute AC charger............ Specifications............ Output Pressure: 6 tons Max Cutting Capacity: Soft steel bolts: 1 1 16" (17mm) Rebar & ground rod: 5 8" (16mm) ACSR : 1 1 2" (40mm) CU & AL strands: 1 1 2" (40mm) Standard guy wire: 5 8" (16mm) Wire rope: 3 4" (20mm) Dimensions (H x W x D): 17" x 12" x 3" Weight with Battery: 14 lbs. Cat. No. DESCRIPTION PKG. QTY. TBM58BSCT Battery-Powered Cutter 1 Battpac LT BPLT58BSCT Battery- Powered Cutter Cuts copper, aluminum and ACSR up to 1 1 2" O.D. Also cuts soft steel bolts, rebar and wire rope Forged steel head and cutting blades for strength and durability Dual forward speeds enhance productivity New, more powerful Ni-MH battery has 50% more energy and less memory effect than old batteries Max. Cutting Capacity: Copper, aluminum & ACSR cable to 1 1 2" O.D. Rebar, ground rod & standard guy wire to 5 8" Soft steel bolts to 1 1 16" Wire rope to 3 4" Dimensions (L x W x H): 19 1 2" x 3 7 8" x 9 7 8" Battery: Ni-MH 14.4V 3.0Ah Weight with Battery: 16.7 lbs. BPLT58BSCT Battery-Powered Cutter with carrying case, charger, 1 two batteries and carry strap. 297-32136 Hydraulic Cutting Head TBM40HCRH Hydraulic Cutting Head Heavy duty cutter with high strength steel blades Cuts both aluminum and copper wire to 1 1 2" O.D. Cutter supplied with carrying case Heat-treated, high-strength steel blades for clean cuts and long service life Quick automatic coupler speeds connection to hydraulic systems Comes with carrying case.... Specifications.... Max. Cutting Capacity (aluminum and copper): 1 1 2" O.D. Dimensions (L x W x H): 14 1 2 x 2 1 2 x 4" Weight: 8.5 lbs................. Max. Cutting Capacity (copper, aluminum and telecommunications cable): Up to 3.35" O.D.* Hydraulic Operating Pressure: 10,000 psi (maximum) * Not designed for cutting steel-reinforced conductors Dimensions (L x W): 15.94" x 5.63" Weight: 10.8 lbs. 297-32136 Hydraulic Cutting Head 1 CAT. NO. DESCRIPTION PKG QTY. TBM40HCRH Hydraulic Cutting Head 1 16

Strippers, Cutters and Other Tools Cable Slicing Die Sets 21649 Cable Bender Cuts copper and aluminum insulated cable sizes from #8 AWG through 500 kcmil Produces clean, squaredend cut, which eliminates extra trimming of conductor strands BY55 21649 Bender for cable up to 750 kcmil 1 CTR-1 C-Tap Removal Tool MAXIMUM CAT. NO. CABLE SIZE TOOLS PKG. QTY. BY55 2/0 TBM6H and TBM6BSCR 1 40C 4/0 TBM14M and 13100A and TBM14BSCR 1 156CS 500 kcmil TBM15I and TBM15BSCR 1 CTR-1 C-Tap Removal Tool 1 Blackburn OD581 Mechanical Compression Tool Equipped with fixed 5/8" die in nose Blackburn TBMODBSCR 6-Ton Battery-Powered Compression Tool Also accepts standard insert O, D and 840 dies Patented, integral self-gauging system in tool head ensures proper adjustment before each crimp Improved lever-action design reduces force required to crimp by as much as 20% Fiberglass handles offer light weight, high strength and superior insulating properties Distribution of weight over tool length enhances balance for easier handling and positioning Versatile battery-powered crimp tool combines the features of an open-yoke tool with the weight and balance of a closed-yoke tool Reduces stress for operator when crimping connectors Ideal for industrial, commercial, telecom and utility applications Accepts T&B 6-TON and Blackburn O and D dies* Installing Range: Up to 4/0 aluminum H-taps Standard C-taps Output Force: 6 tons Dimensions (L x W x H): 12" x 3" x 13" Battery: Ni-MH 14.4V 3.0 Ah Weight with Battery: 8 lbs. OD581 Mechanical Compression Tool with Fixed 5 8" 1 Nose Die, Insert Die Cavity for O, D or 840 Die (sold separately) and 21" Fiberglass Handles TBMODBSCR Battery-Powered 6-TON Crimping Tool Includes 1 Shoulder Strap, Charger, Carrying Case, Battery Cartridge and Owners Manuals *T&B 6-TON and Blackburn O and D dies sold separately. 17

Installing Dies Dies for Standard Lugs & Splices (TBM25S TBM12) 13642M / 13400 TBM12 CONNECTOR SIZE TBM8-750M-1 TBM-8/8S TBM-5/5S TBM6/6S / 25000 HYDRAULIC HEAD HYDRAULIC HEAD CODE COLOR-KEYED TBM8-750BSCR TBM8 DIE TBM5 DIE CAT. NO. CAT. NO. DIE DIE DIE DIE COPPER FLEX/24 AL/CU DIE COLOR TBM25S TBM4S TBM8-750 CAT. NO. CAT. NO. UPPER DIE LOWER DIE CAT. NO. CODE NO. CAT. NO. CODE NO. 8 AWG 37/24 10 AWG RED 13475 13477 11732 21 TBM12D-1 21 6 AWG 61/24 8 AWG BLUE 13475 13477 11733 24 TBM12D-1 24 4 AWG 91/24 6 AWG GRAY 13461 13454 13472 13476 11734 29 TBM12D-2 29 2 AWG 125/24 BROWN 13474 13477 11735 33 TBM12D-2 33 1 AWG 150/24 4 AWG GREEN C-Taps Only 13474 13477 11736 37 TBM12D-3 37 1/0 225/24 2 AWG PINK 13475 13477 11737 42 TBM12D-3 42 2/0 275/24 BLACK 13462 13455 13474 13477 11738 45 TBM12D-4 45 3/0 325/24 ORANGE 13474 13477 11739 50 TBM12D-4 50 4/0 450/24 PURPLE 13475 13477 11740 54 TBM12D-5 54 250 kcmil 550/24 YELLOW 13463 13456 13473 13476 11771 62 TMB12D-5 62 1 AWG GOLD 13474 13477 11738 45 TBM12D-4 45 1/0 TAN 13474 13477 11739 50 TBM12D-4 50 2/0 OLIVE 13464 13457 13475 13477 11740 54 TBM12D-5 54 3/0 RUBY 13473 13476 11741 60 TBM12D-5 60 300 kcmil 4/0 WHITE 13465 13473 13476 11742 66H TBM12D-5 66H 350 kcmil 775/24(short) 250 kcmil RED 13466 13458 13472 13476 11743 71H TBM12D-4 71H 400 kcmil 775/24(long) 300 kcmil BLUE 13467 4/0 only 13472 13476 11744 76H TBM12D-4 76H 925/24* N/A 13479 13476 11745 80H N/A 500 kcmil 350 kcmil BROWN 13468 13478 13478 11746-TB 87H TBM12D-3 87H 600 kcmil 1100/24 400 kcmil GREEN 11747 94H TBM12D-3 94H GREEN 94H 1325/24** PINK 700 kcmil 500 kcmil PINK 11748 99H TBM12D-2 99H 750 kcmil 650 kcmil BLACK 11749 106H TBM12D-2 106H 800 kcmil ORANGE 11750 107H 700 kcmil PURPLE 11751 112H TBM12D-1 112H 900 kcmil 1925/25 750 kcmil YELLOW 11753 115H TBM12D-1 115H 1000 kcmil 800 kcmil 1000 kcmil * Standard barrel only. Long barrel requires Brown 87H. ** Standard barrel only. Long barrel requires Black 106H. 18

Installing Dies Dies for Standard Lugs & Splices (TBM6H 21940) BPLT14BSCR / TBM14M BPLT15BSCR / CONNECTOR SIZE BPLT6BSCR / TBM6H BPLT62BSCR TBM14MC / 13100A* TBM15I*** 21940 (40 TON) CODE COLOR-KEYED DIE DIE DIE DIE DIE DIE DIE DIE DIE DIE COPPER FLEX/24 AL/CU DIE COLOR CAT. NO. CODE NO. CAT. NO. CODE NO. CAT. NO. CODE NO. CAT. NO. CODE NO. CAT. NO. CODE NO. 8 AWG 37/24 10 AWG RED 6TON21 21 TBM6221 21 15520 21 15520 21 6 AWG 61/24 8 AWG BLUE 6TON24 24 TBM6224 24 15522 24 15522 24 4 AWG 91/24 6 AWG GRAY 6TON29 29 TBM6229 29 15527-CK 29 15527-CK 29 11401 29 2 AWG 125/24 BROWN 6TON33 33 TBM6233 33 15528 33 15528 33 11402 33 1 AWG 140/24 4 AWG GREEN 6TON37 37 TBM6237 37 15513-CK 37 15513-CK 37 11333 37 1/0 225/24 2 AWG PINK 6TON42 42 TBM6242 42 15508 42 15508 42H 11334 42 2/0 275/24 BLACK 6TON45 45 TBM6245 45 15526 45 15526 45 11405 45 3/0 325/24 ORANGE 6TON50 50 TBM6250 50 15530 50 15530 50 11406 50 4/0 450/24 PURPLE 6TON54 54 TBM6254 54 15511 54 15511 54H 11407 54H 250 kcmil 550/24 YELLOW 6TON62 62 TBM6262 62 15510-CK 62 15510-CK 62 297-31669-7 62 1 AWG GOLD 6TON45 45 TBM6245 45 15526 45 15526 45 11405 45 1/0 TAN 6TON50 50 TBM6250 50 15530 50 15530 50 11406 50 2/0 OLIVE 6TON54 54 TBM6254 54 15511 54 15511 54H 11407 54 3/0 RUBY 6TON60 60 TBM6260 60 15532-CK 60 15532-CK 60 11408 60 300 kcmil 4/0 WHITE 6TON66 66H TBM6266 66 15534 66H 15534 66H 11409 66 350 kcmil 775/24(short) 250 kcmil RED 6TON71 71H TBM6271 71 15514-CK 71H 15514-CK 71H 11363 71 400 kcmil 775/24(long) 300 kcmil BLUE 6TON76 76H TBM6276 76 15512 76H 15512 76H 11410 76 925/24* N/A 6TON80 80H TBM6280 80 15517 80H 15517 80H N/A 15606 80 500 kcmil 350 kcmil BROWN 6TON87 87H TBM6287 87 15506 87H 15506 87H 11423 87 600 kcmil 1100/24 400 kcmil GREEN 6TON94 94H 15611 94H 11364 94 GREEN 15536-CK 94H 15536-CK 94H 1325/24** PINK Pink 700 kcmil 500 kcmil PINK 99H 15505 99H 15505 99H 11424 99 750 kcmil 650 kcmil BLACK 106H 15515-CK 106H 15515-CK 106H 74506 106 800 kcmil ORANGE 107H 15608 107H 11425 107 700 kcmil PURPLE 112H 15609 112H 11426 112 900 kcmil 1925/24 750 kcmil YELLOW 115H 15504 115H 15504 115H 11308 115 1000 kcmil 800 kcmil 15603 125H 11416 125 1000 kcmil 15602 140H 11418 140 15601 150H 11419 150 *Standard barrel only. Long barrel requires Brown 87H. **Standard barrel only. Long barrel requires Black 106H. ***15500 Series dies require 15500-TB adapter. 15500F for full size die to fit TBM15I without adapter. 19

Installing Dies Dies for Standard C-Taps TBM25S TBM5/5S TBM6/6S TBM8/8S BPLT62BSCR TBM6H/BPLT6BSCR CONNECTOR COLOR CODE DIE NO. DIE NO. DIE NO. DIE NO. DIE NO. DIE NO. 54705 RED Red Red Nest 13454 13475/13477 13461 TBM6221 6TON21 54710 BLUE Blue Blue Nest 13454 13475/13477 13461 TBM6224 6TON24 54715 GRAY Gray Grey Nest 13454 13472/13476 13461 TBM6229 6TON29 54720 BROWN Brown Brown Nest 13454 13474/13477 13461 TBM6233 6TON33 54725 GREEN Green Green Nest 13455 13474/13477 13462 TBM6237 6TON37 54730 PINK Pink 13455 13475/13477 13462 TBM6242 6TON42 54735 BLACK Black 13455 13474/13477 13462 TBM6245 6TON45 54740 ORANGE Orange 13455 13474/13477 13462 TBM6250 6TON50 54745 PURPLE Purple 13456 13475/13477 13463 TBM6254 6TON54 54750 YELLOW Yellow 13456 13473/13478 13463 TBM6262 6TON62 Dies for Large C-Taps 13100A/JB12B/TBM14M/ TBM15I/ 13642M/13400 TBM12 BPLT14BSCR BPLT15BSCR CONNECTOR COLOR CODE DIE NO. DIE NO. DIE NO. DIE NO. 54755 BLUE Blue 11744 TBM12D-4 15512 15512 54760 BROWN Brown 11746-TB TBM12D-3 15506 15506 54765 PINK Pink 11748 TBM12D-2 15505 15505 54770 BLACK Black 11749 TBM12D-2 15515-CK 15515-CK 54775 YELLOW Yellow 11753 TBM12D-1 15504 15504 54780 WHITE White 15603 54785 N/A 15603 54790 N/A 15603 Dies for Copper H-Taps 13100A/JB12B/TBM14M/ TBM15I/ TBM6H/BPLT6BSCR BPLT14BSCR BPLT15BSCR CONNECTOR COLOR CODE DIE NO. DIE NO. DIE NO. CHT814-10 GREEN Green 6TON37R 15CA37RCH 15CA37RCH CHT214-9 BROWN Brown 6TON71R 15CA71RCH 15CA71RCH CHT250214-8 PURPLE Purple 15CA80RCH 15CA80RCH CHT25014-7 PURPLE Purple 15CA80RCH 15CA80RCH CHT2502-6 PURPLE Purple 15CA80RCH 15CA80RCH CHT50010-5 BROWN Brown 15612CH CHT50040-4 BROWN Brown 15612CH CHT75010-3 YELLOW Yellow 15620CH CHT750350-2 YELLOW Yellow 15620CH CHT75040-11 YELLOW Yellow 15620CH CHT750350-1F WHITE White 15620CHF 20

Installing Dies Dies for Aluminum H-Taps 13100A/JB12B/TBM14M/ TBM15I/ TBM5/5S TBM6/6S TBM8/8S TBM12 TBM6H/BPLT6BSCR BPLT14BSCR BPLT15BSCR CONNECTOR COLOR CODE DIE NO. DIE NO. DIE NO. DIE NO. DIE NO. DIE NO. DIE NO. 63105 ORANGE Orange 13455 13474/13477 13462 TBM12D-4 6TON50 15530 15530 63110 GREEN Green 13470 TBM12D-H OJB 15501A 15501A 63118 GREEN Green 13470 TBM12D-H OJB 15501A 15501A 63125 GREEN Green 13470 TBM12D-H OJB 15501A 15501A 63140 BLUE Blue 13471 TBM12D-H DBL 15502 15502 63148 BLUE Blue 13471 TBM12D-H DBL 15502 15502 63160 RED Red 15612 63169 BLACK Black 15620 63170 BLACK Black 15620 63180 BLACK Black 15620 Dies for Figure 6 & Figure 8 Ground Connectors CABLE TO CABLE TO GROUND ROD TO REBAR DIE SELECTION CONNECTOR ELEMENT A ELEMENT B ELEMENT B ELEMENT B ELEMENT A ELEMENT B 54855L #6 Sol. #2 Str. #6 Sol. #2 Str. 15501A 15501A 54865L #1 Str. 250 kcmil #6 Sol. #2 Str. 1 2" - 5 8" Rod 3 8" 1 2" #3 - #4 Rebar 15G86R 15501A 54875L #2 Str. 250 kcmil #2 Str. 250 kcmil 1 2" - 5 8" Rod 3 8" 1 2" #3 - #4 Rebar 15G86R 15G86R 54885L 250 kcmil 500 kcmil #6 Sol. #2 Str. 5 8" - 3 4" Rod 5 8" 3 4" #3 - #4 Rebar 15G126R 15501A 54895L 250 kcmil 500 kcmil #2 Str. 250 kcmil 5 8" - 3 4" Rod 5 8" 3 4" #3 - #4 Rebar 15G126R 15G86R 54900L 250 kcmil 500 kcmil #2 Str. 250 kcmil 5 8" - 3 4" Rod 5 8" 3 4" #3 - #4 Rebar 15G121R 15G121R Dies for High-Voltage Connectors TBM15I, TBM14M, 13100A DIE CODE **ADAPTER** NON-ADAPTER NO. TYPE TYPE 29R 15CA29R 33R 15CA33R 37R 15CA37R 42R 15CA42R 45R 15CA45R 49R 15CA49R 54R 15CA54R 60R 15CA60R 66R 15CA66R 71R 15CA71R 76R 15CA76R 87R 15CA87R 94R 15CA94R 106R 15CA106R 125R 15C125R* *To be used with TBM15I only. **Use 15500-TB adapter with TBM15I tool. Not UL Listed in TBM14M/13100A tool. 21

Stripping and Cutting Tools Single operation to cut and strip at the same time! SWS01/DWS02 Wire Stripping/Cutting Tools SWS01 Automatic adjustment to the diameter of the wire, with neither setting nor selection Sharply cuts and strips insulator without damaging the conductors DWS02 is a double-side stripper, stripping two wires at the same time DWS02 PKG. CAT. NO. DESCRIPTION QTY. SWS01 Single-Side Stripper 1 DWS02 Double-Side Stripper 1 Integral wire cutter lets user cut and strip with the same tool! Sta-Kon ERG1-WS Wire Stripping/Cutting Tool V Blade Cassette Interchangeable cassettes enable the user to strip a wide range of insulations without having to change tools Tool automatically strips wire to preset length PKG. CAT. NO. DESCRIPTION QTY. ERG1-WS Ergonomic Wire Stripping Tool 1 SBC-1 Replacement Straight Blade Cassette 1 VBC-1 Replacement V Blade Cassette 1 ERG1-WS Wire Stripping/Cutting Tool is shipped with one Straight Blade Cassette. V Blade Cassettes sold separately. 22

Manual Crimping Tools Used for installation of various Sta-Kon terminal series. Plier-Type Tools WT111M WT110M WT112M WT161M WT2000 CAT. NO. FOR USE WITH STA-KON SERIES PKG. QTY. WT110M A, B, C non-insulated terminals and splices and A, B non-insulated terminals with insulation grip 1 WT111M A, B, C, PT non-insulated terminals and splices; includes cutters 1 WT112M A, B, C non-insulated and RA, RB, RC insulated nylon and vinyl terminals and splices; includes cutters 1 WT161M A, B, C, PT non-insulated terminals and splices; includes plier grip and cutters 1 WT2000 A, B, C, AB, PT, RA, RB, RC insulated and non-insulated terminals and splices; includes wire cutters, 1 bolt cutters and wire stripper 23

Manual Crimping Tools Ergonomically designed handles let user get a grip on safety. For easy visual verification of crimps, integrity dots are embossed on the top and bottom of the terminal. Color-coded die nests on both the right and left sides of the tool are included for insulated terminals. Toggle action increases mechanical gain, which dramatically reduces handle force and the stress on your hands. Shure-Stake mechanism ensures a complete crimp cycle before it releases the tool. Advanced ergonomic design of handle distributes the force more evenly across the hand. ERG2001 Rubberized thermoplastic handle combines maximum friction with a soft, comfortable feel that reduces muscle tension. Comfort Crimp Terminal Tool Concerned about safety? Down time? Health care costs? The Thomas & Betts ergonomically-designed Comfort Crimp tool helps reduce the risk of carpal tunnel syndrome, the cause of almost one out of every two industrial injuries. This tool s unique design delivers the same reliable crimp with up to 60% less handle force than other terminal hand tools, so you won t have to sacrifice your hand to make a successful crimp. We ve researched the tool components to provide maximum comfort to the operator while ensuring a complete crimp. Just wrap your hands around our Comfort Crimp terminal tool. It s such a relief you won t want to handle any other tool ever again. ERG2002 ERG2007 ERG2004 ERG2008 ERG2005 PKG. CAT. NO. FOR USE WITH STA-KON SERIES QTY. ERG2001 RA, RB, RC Nylon & vinyl terminals, splices & disconnects 1 ERG2002 A, B, C Non-insulated terminals, splices, disconnects 1 ERG2004 A,B and C Flag terminals 1 ERG2005 B, C, D, E Non-insulated terminals, splices, (D & E tubular only) 1 ERG2006 RA, RB.110 Disconnects and RAX Terminals 1 ERG2007 RD & RE Insulated terminals (tubular only) 1 ERG2008 Non-insulated terminals #8 1/0 AWG (tubular only) 1 NOTE: Contact for gauging. 24

Manual Crimping Tools WT1377 Ratchet Hand Tool WT2130A Ratchet Hand Tool Correct compression every time the Shure-Stake mechanism principle prevents opening of the handles until full staking action is completed. Installs self-insulated and non-insulated Sta-Kon terminal series in the #26 10 AWG wire range. CAT. NO. FOR USE WITH STA-KON SERIES PKG. QTY. WT1377 NW Ring Terminals 1 CAT. NO. FOR USE WITH STA-KON SERIES PKG. QTY. WT2130A RC, RBC and RD insulated 1 terminals, RC6, RP7 wire joints ERG2006 Hand Tool WT3185 Ratchet Hand Tool CAT. NO. FOR USE WITH STA-KON SERIES PKG. QTY. ERG2006 RZ, RV Terminals/Splices 1 RA, RB.110 insulated disconnects CAT. NO. FOR USE WITH STA-KON SERIES PKG. QTY. WT3185 For 8 AWG to 250 MCM Non-Insulated Sta-Kon Terminals 1 NOTE: For gauging information, contact. ERG1255 Ratchet Hand Tool WT129 Flag Terminal Type Hand Tool CAT. NO. FOR USE WITH STA-KON SERIES PKG. QTY. ERG1255 RA, RB, RC Heat-Shrinkable nylon insulated 1 terminals, butt splices, and disconnects CAT. NO. FOR USE WITH STA-KON SERIES PKG. QTY. WT129 D, E, F & G Non-Insulated Flag Terminals 1 25

Manual Crimping Tools WT115A Toggle-Type Hand Tool PKG. CAT. NO. FOR USE WITH STA-KON SERIES QTY. WT115A D, E, F & G Non-Insulated Terminals 1 TBM6 & TBM6S Toggle-Type Hand Tools Installing Dies for Non-Insulated Code and Aircraft Sta-Kon Terminals TBM6 CAT. NO. NEST INDENTOR STATIONARY MOVABLE TERM. DIE DIE SIZE 11803 D, E (Tubular) 11805 E (Brazed), F (Tubular) 11806 11802 F (Brazed), G 11807 H 11808 J 11809 K 11810 L 11811 M Installing Dies for Nylon Insulated Sta-Kon Terminals TBM6 & TM6S Tool PKG. CAT. NO. FOR USE WITH STA-KON SERIES QTY. TBM6 D through M, RD through RM 1 TBM6S D through M, RD through RM with Shure-Stake 1 Dies not included. CAT. NO. TERM. DIE SET SIZE 11821 RD 11822 RE 11823 RF 11824 RG 11825 RH 11826 RJ 11827 RK 11828 RL 11829 RM 26

Safe, fast, high-volume crimping machine! Shure-Stake Auto-Feed Tool Shure-Stake mechanism Fully guarded foot pedal Clear plastic safety guard over die area Dies color coded to terminals #26 10 AWG wire range Installs insulated and non-insulated terminals and disconnects Pneumatic Crimping Tools PKG. CAT. NO. DESCRIPTION QTY. 12050 Compact, pneumatically operated unit for crimping tape-mounted Sta-Kon terminals; 1 equipped with Shure-Stake mechanism, which ensures a full compression each time Space Requirement: 30" W x 20" H x 20" D Weight: 55 lbs. Air Pressure: 90 125 psi input air supply Installing Dies for 12050 STA-KON AWG DIE PKG. TERMINAL TYPE WIRE SIZE CAT. NO. QTY. RA Nylon 22 18 12051 RA Vinyl 22 18 12054* 1 RA.110 Disconnect 22 18 12061 1 RB Nylon 16 14 12052 1 RB Vinyl 16 14 12055* 1 RB.110 Disconnect 16 14 12062 1 RC Nylon and 12 10 12056 1 Vinyl Insulated A Non-Insulated 22 18 12057 1 B Non-Insulated 16 14 12058 1 C Non-Insulated 12 10 12059 1 C Disconnect, Non-Insulated 12 10 12060 1 RV RZ 26 24 683-54335 1 * Can also be used on nylon. 27

Battery-Powered Crimping Tools 1 1 2 tons of force that weighs less than 3 pounds! BAT22-6 Battery-Powered Crimping Tool T&B s BAT22-6 battery-powered tool is fast and portable for making highvolume and difficult-to-reach terminal installations in a snap. The Sta-Kon BAT22-6 delivers 1.5 tons of crimping force with an easy, pushbutton trigger. The lightweight, ergonomic design minimizes the risk of repetitive motion injuries that can occur with traditional hand crimping tools. And at less than three pounds, one-hand operation is easy while still packing enough power to crimp up to 6 AWG terminals in seconds. Interchangeable dies can be quickly changed to crimp non-insulated and insulated terminals up to 6 AWG Dies are the same as our hand tools crimps will be exactly the same between Sta-Kon hand tools such as our ERG2001 and the BAT22-6 360 rotating head gives user the added flexibility when crimping hard-toreach connections Short cycle time equates to crimping times of less than two seconds Quick, lightweight and maneuverable NiCd battery operation provides long-lasting battery life to complete up to 150 crimps on a single charge Extra battery and charger are included with the tool, ensuring round-the-clock operation Battery charger provides full battery life in under an hour Linear crimping motion gives a symmetric, high-quality crimp every time Easy to rotate with your wrist delivers fast and effective crimping power. Uses the exact dies of the Comfort Crimp line of ergonomic tools for Sta-Kon and Dragon Tooth. Included Accessories Sturdy, plastic carrying case for portability Two 9.6V NiCd batteries and battery charger Sturdy tray for convenient storage of crimp dies PKG. CAT. NO. DESCRIPTION QTY. BAT22-6 Battery Crimping Tool, 1.5 Ton with 120 VAC Charger 1 Crimp Dies* DIE2001 Insulated 22 10 AWG Sta-Kon Terminals 1 DIE2002 Non-Insulated 22 10 AWG Sta-Kon Terminals 1 DIE2005 16 14/12 10/8 6 (Tubular Only) Sta-Kon Terminals 1 DIE2007 Insulated 8 6 AWG Sta-Kon Terminals 1 * Dies sold separately. 28

Hydraulic Crimping Tools Crimp 22 6 AWG terminals! BAIR22-6 Bench-Mounted Air Tool 1.5 tons of grip Bench-mounted heavy-duty air tool Short cycle time Shure-Stake mechanism Foot actuated Accepts T&B standard hand tool dies Installs Sta-Kon and Spec-Kon terminals as well as ferrules and Dragon Tooth connectors BAIR22-6 Heavy-duty, high-speed production tool installs a wide range 1 of Sta-Kon terminals, from 26-6 gauge; uses the ERG2000 series dies for both non-insulated and insulated terminals; supplied complete with foot pedal, air hose/air lubricator Crimp Dies* DIE2001 Insulated 22 10 AWG Sta-Kon Terminals 1 DIE2002 Non-Insulated 22 10 AWG Sta-Kon Terminals 1 DIE2005 16 14/12 10/8 6 (Tubular Only) Sta-Kon Terminals 1 DIE2007 Insulated 8 6 AWG Sta-Kon Terminals 1 * Dies sold separately. NOTE: The dies for the BAIR22-6, PAIR22-6 and BAT22-6 are interchangeable. 1.5 tons of portable force! PAIR22-6 Portable Air Hydraulic Tool Crimps 22-6 AWG terminals Portable heavy-duty air tool Installs Sta-Kon terminals as well as ferrules and Dragon Tooth connectors Interchangeable dies Open yoke enables easy access to insert and remove terminals for crimping PAIR22-6 Open yoke; hand actuated 1 Crimp Dies* DIE2001 Insulated 22 10 AWG Sta-Kon Terminals 1 DIE2002 Non-Insulated 22 10 AWG Sta-Kon Terminals 1 DIE2005 16 14/12 10/8 6 (Tubular Only) Sta-Kon Terminals 1 DIE2007 Insulated 8 6 AWG Sta-Kon Terminals 1 *Dies sold separately. NOTE: The dies for the BAIR22-6, PAIR22-6 and BAT22-6 are interchangeable. 29

Hydraulic Crimping Tools Crimps 8 AWG 250 mcm! Air-Operated Bench-Mounted Tool Convenience and Economy The tool accepts a full range of interchangeable dies, the same as used in the TBM6 or TBM6S tools. To install the dies, simply pull the springloaded pin and remove the indentor die. Then, flex the retaining spring and remove the die nest. Shure-Stake Mechanism Means Quality Connections The Shure-Stake mechanism senses inlet air pressure, and if insufficient, is designed to prevent the tool from cycling. Thus you avoid undercrimping. An 85 90 psi air pressure source is required. Safety Features Increase Productivity, Reduce Downtime Safety features include a guard over the die area, an air shutdown switch activated by a slight push with the finger, and an enclosed foot pedal designed to prevent unwanted tool operation. In addition, the tool may be bench-mounted for stability and control. For convenience when crimping large size terminals on heavy wire, the head assembly may overhang the workbench. 25000 This compact heavy-duty air tool installs nylon 1 insulated Sta-Kon terminals on wire sizes from 8 AWG to 250 mcm; non-insulated styles are also installed just as quickly and dependably; Heavy-duty air tool installs non-insulated and insulated Sta-Kon terminals from 8 AWG to 250 mcm NOTE: This tool uses the same dies as the TBM6 and TBM6S hand tools on page 26. 30

Hydraulic Crimping Tools Installs insulated and noninsulated Sta-Kon Terminals! 12-Ton Crimping Tool 13400 12-ton crimping tool for installing both insulated and non-insulated Sta-Kon terminals 1 #8 to 250 mcm (dies ordered separately) Military listed and 12 tons of crimping power! 12-Ton Crimping Tool (Military Spec. MS25441-1) 13642M Hydraulic-operated 12-ton tool installs #8 through 250 mcm Sta-Kon 1 terminals (dies ordered separately) Hex Dies for Non-Insulated Sta-Kon Terminals to Fit 13642M and 13400 DIE CAT. NO. FOR FOR HEX TUBULAR BRAZED STA-KON WIRE DIE TERM SEAM SIZE SIZE CODE 11732 D 8 21 11733 D 8 24 11733 E 6 24 11734 E 6 29 11734 F 4 29 11735 F 4 33 11736 G 2-1 37 11737 H 1/0 42 11738 J 2/0 45 11739 K 3/0 50 11740 L 4/0 54 11771 M 250 mcm 62 13642M Indent Style Dies for Sta-Kon Brazed Seam Non-Insulated Terminals to Fit 13642M and 13400 NEST INDENT. STA-KON WIRE PKG. CAT. NO. CAT. NO. SIZE SIZE QTY. 13643 D 8 1 13644 13650 E 6 1 13645 F 4 1 Indent Style Dies for Sta-Kon Tubular Non-Insulated Terminals to Fit 13642M and 13400 NEST INDENT. STA-KON WIRE PKG. CAT. NO. CAT. NO. SIZE SIZE QTY. 13654 13650 G 2 1 1 13655 13650 H 1/0 1 13656 13650 J 2/0 1 13657 13650 K 3/0 1 13658 13650 L 4/0 1 13659 13650 M 250 mcm 1 Installing Dies for Insulated Sta-Kon Terminals to Fit 13642M (Military Listed) DIE STA-KON WIRE PKG. CAT. NO. SIZE SIZE QTY. 21707M RD 8 1 21708M RE 6 1 21709M RF 4 1 21710M RG 2 1 1 21711M RH 1/0 1 21712M RJ 2/0 1 21713M RK 3/0 1 21714M RL 4/0 1 21715M RM 250 mcm 1 Hex Dies for Non-Insulated Sta-Kon Terminals to Fit 13642M (Military Listed) DIE STA-KON WIRE PKG. CAT. NO. SIZE SIZE QTY. 11781M D 8 1 11782M E 6AN 1 11783M F 4AN 1 11784M G 2AN 1 11785M H 1AN 1 11786M J 1/0AN 1 11787M K 2/0AN 1 11788M L 3/0AN 1 11789M M 4/0AN 1 Indent Style Dies for Flag Type Sta-Kon Terminals Use with 13642M and 13400 NEST INDENT. STA-KON WIRE PKG. CAT. NO. CAT. NO. SIZE SIZE QTY. 21733 D 8 1 21734 21731 E 6 1 21735 F 4 1 21736 G 2 1 21737 G 1 1 21738 21732 H 1/0 1 21739** J 2/0 1 21740** K 3/0 1 21741** L 4/0 1 ** Cat. Nos. 21739, 21740 and 21741 dies must be left in 13642 head with 21732 indentor when gauging. 31

Hydraulic Pumps 13600 Electric Hydraulic Pump Designed for use with single-acting cylinders and tools rated for 10,000 psi operation Supplied with metal carrying case 13620 hand switch and 13619 hydraulic hose, both sold separately, required for operation..... Specifications...... Motor: 1 2 hp, 115V 50 60 Hz 10 amps Pumping Capacity: 170 cu. in./min. at 100 psi 32 cu. in./min. at 1,000 psi 25 cu. in./min. at 5,000 psi 18 cu. in./min. at 10,000 psi Reservoir Volume: 104 cu. in. (.45 gal.) Basic Pump Dimension: 6" x 8" x 16" Weight: 25 lbs. 13810 Heavy-Duty Electric Hydraulic Pump with Shure-Stake Control Designed for perfect crimps every time in heavy-duty OEM applications Heavy-duty OEM two-stage pump with high flow rate Shure-Stake control mechanism requires 9,800 psi pump pressure before recyling to prevent under-crimping Requires hand or foot control (sold separately) 13600 Electric Hydraulic Pump hand or foot switch and 1 non-metallic hose (sold separately) required for operation 13610A Electric Hydraulic Pump with Shure-Stake Control Shure-Stake control mechanism requires 9,800 psi pump pressure before recyling to prevent undercrimping Designed for use with single-acting cylinders and tools rated for 10,000 psi operation Supplied with metal carrying case Motor Rating: 1 1 2 hp, 115V, 60 Hz, 23 amps Pumping Capacity: 235 cu.in./min. at 200 psi 6 cu.in./min. at 8,000 psi Reservoir Volume: 462 cu.in./2 gal. Dimensions (L x W x H): 10 3 4" x 15" x 20 3 4" Weight: 60 lbs. 13810 Heavy-duty electric hydraulic pump with Shure-Stake 1 control hand or foot switch and non-metallic hose (sold separately) required for operation Accessories for the pumps on this page Motor Rating: 1 2 hp, 115V, 50-60 Hz, 12.5 amps Pumping Capacity: 170 cu. in./min. at 100 psi 32 cu. in./min. at 1,000 psi 25 cu. in./min. at 5,000 psi 18 cu. in./min. at 10,000 psi Reservoir Volume: 104 cu. in. (.45 gal.) Basic Pump Dimension: 8 1 2" x 10 1 2" x 16" Weight: 35 lbs. 13610A Electric Hydraulic Pump with Shure-Stake control 1 hand or foot switch and non-metallic hose (sold separately) required for operation You may also need for 13600 13620 Hand Switch 10 ft. 1 13589A Foot Switch 10 ft. 1 13619 10 ft. Non-Metallic Hose 1 13618 20 ft. Non-Metallic Hose 1 13600S Sled type stand for 13600 pump 1 You may also need for 13610A & 13810 13611 Hand Switch 10 ft. 1 13612 Foot Switch 10 ft. 1 13619 10 ft. Non-Metallic Hose 1 13618 20 ft. Non-Metallic Hose 1 32

Tool Selection Charts Critical information for determining the products you need! RATCHET HAND PLIERS ERGONOMIC RATCHET HAND TOOLS TOOLS TERMINAL TERMINAL TYPE SERIES WT110M WT111M WT112M WT161M WT2000 ERG2001 ERG2002 ERG2004 ERG2005 ERG2006 ERG1255 WT1377 WT145A RZZ RA, RAX Nylon Terminals RB RBC, RC RA Nylon Butt Splices RB RC RAA Nylon Parallel Splices RBB RCC RA All Nylon Disconnects RB (except.110 size) RC Heat Shrinkable RAS Terminals, Splices, RBS Disconnects RCS RA, RAA Vinyl Terminals RB, RBB and Splices RC, RCC, RBC A,AA Bare Terminals B,BB and Splices C,CC RB RC Wire Joints RP PT Hi-Temp Terminals NW-Rings and Splices NW-Splices A Insulation Grip B A,B.110 Disconnects RA,RB AB Flag Terminals C RAT, RAAT Tefzel Terminals RBT, RBBT and Splices RCT, RCCT RA Vinyl Disconnects RB RC A Bare Disconnects B C Tefzel is a registered trademark of DuPont. 33

Tool Selection Charts (continued) Critical information for determining the products you need! RATCHET HAND BAT22-6 BAIR22-6 TOOLS (CONT.) PAIR22-6 12050 MYLAR TAPE AUTO TOOL TERMINAL TERMINAL TYPE SERIES WT145C WT2130A DIE2001 DIE2002 DIE2005 12051 12052 12054 12055 12056 12057 12058 12059 12060 683-54335 RZZ Nylon Terminals RA, RAX RB RBC, RC RA Nylon Butt Splices RB RC RAA Nylon Parallel Splice RBB RCC RA All Nylon Disconnects RB (except.110 size) RC Heat Shrinkable RAS Terminals, Splices, RBS Disconnects RCS RA, RAA Vinyl Terminals RB, RBB and Splices RC, RCC, RBC A,AA Bare Terminals B,BB and Splices C,CC RB Wire Joints RC RP PT Hi-Temp Terminals NW-Rings and Splices NW-Splices Insulation Grip A B.110 Disconnects A,B RA,RB Flag Terminals AB C RAT, RAAT Tefzel Terminals RBT, RBBT and Splices RCT, RCCT RA Vinyl Disconnects RB RC A Bare Disconnects B C Tefzel is a registered trademark of DuPont. 34

Select the die numbers you need! Die Selection Charts 25000 AIR TOOL 13642M (MS25441-1) HAND TBM6 TOGGLE HAND TOOL AND TOOL TBM6S TOGGLE HAND TOOL 13400 HYDRAULIC TOOL TERMINAL WITH DIE CAT. NOS. HEX DESCRIPTION SERIES TYPE DIES NEST (STATIONARY) INDENTOR (MOVABLE) DIES NEST INDENTOR Non-Insulated Terminals and Splices Tefzel Nylon Insulated Terminals and Splices Non-Insulated Flag Terminals D Tubular ERG2005 11803 11802 11781M* 13651 13650** D Tubular ERG2008 11803 11802 11781M* 13651 13650** D Tubular WT3185/WT115A 11803 11802 11732 13651 13650** D Brazed WT3185/WT115A 11803 11802 11733 13643 13650** E Tubular ERG2005 11803 11802 1182M 13652 13650** E Tubular ERG2008 11803 11802 1182M 13652 13650** E Tubular WT3185/WT115A 11803 11802 11733* 13652 13650** E Brazed WT3185/WT115A 11805 11802 11734 13644 13650** F Tubular ERG2008 11805 11802 11783 13653 13650** F Tubular WT3185/WT115A 11805 11802 11734* 13653 13650** F Brazed WT3185/WT115A 11806 11802 11735 13645 13650** G Tubular ERG2008 11806 11802 11784M* 13654 13650** G Tubular WT3185/WT115A 11806 11802 11736 13654 13650** H Tubular ERG2008 11807 11802 11785M* 13655 13650** H Tubular WT3185 11807 11802 11785M* 13655 13650** H Tubular WT3185 11807 11802 11737 13655 13650** J Tubular WT3185 11808 11802 11786M* 13656 13650** J Tubular WT3185 11808 11802 11738 13656 13650** K Tubular 11809 11802 11787M* 13657 13650** K Tubular 11809 11802 11739 13657 13650** L Tubular 11810 11802 11788M* 13658 13650** L Tubular 11810 11802 11740 13658 13650** M Tubular 11811 11802 11789M* 13659 13650** M Tubular 11811 11802 11771 13659 13650** RD Tubular ERG2007 11821 (Set) 21707M* (Set) RD Brazed 11822 (Set) 21708M* (Set) RE Tubular ERG2007 11822 (Set) 21708M* (Set) RE Brazed 11823 (Set) 21709M* (Set) RF Tubular 11823 (Set) 21709M* (Set) RF Brazed 11824 (Set) 21710M* (Set) RG Tubular 11824 (Set) 21710M* (Set) RH Tubular 11825 (Set) 21711M* (Set) RJ Tubular 11826 (Set) 21712M* (Set) RK Tubular 11827 (Set) 21713M* (Set) RL Tubular 11828 (Set) 21714M* (Set) RM Tubular 11829 (Set) 21715M* (Set) D WT129 21733 21731 E WT129 21734 21731 F WT129 21735 21731 G WT129 21736 21732 H 21737 21732 J 21738 21732 K 21739 21732 L 21740 21732 M 21741 21732 * Indicates military listed die. ** To order the military version, suffix the indentor catalog number with an "M" (13650M). Nest catalog number does not change. Tefzel is a registered trademark of DuPont. Stud Size and Clearance Hole Chart STUD SIZE 2 4 6 8 10 1 4 Min. hole diam. in. 0.92.116.143.169.196.262.323.388.453.516.650.775 Min. hole diam. mm 2.337 2.946 3.632 4.292 4.978 6.655 8.204 9.855 11.506 13.106 16.510 19.685 5 16 3 8 7 16 1 2 5 8 3 4 35

Manual and Battery-Powered Crimping Tools Ergonomic Manual Installation Tools ERG1806 Fixed die tool Incorporates the ergonomically designed Comfort Crimp tool handles, which distribute the force more evenly across the hand Shure-Stake mechanism ensures a complete crimp cycle before the tool releases Rubberized thermoplastic handles combine maximum friction with a soft, comfortable feel that reduces muscle tension Two-piece movable die nest provides easy connector removal (ERG811 has single die nest) ERG811 CAT. NO. TOOL GAUGING CONNECTOR PKG. QTY. ERG1801.069 max. 22F, L, R-1 Series 1 ERG1802.076 max. 22L002 1 ERG1804.034 max. 22L004 1 ERG1806.095 max. 22F, L, R-6 Series 1 ERG811.103 max. 214420 1 Contact for availability and most recent additions to the ergonomic tool series. BAT22-6 Battery-Powered Crimping Tool T&B s BAT22-6 battery-powered tool is fast and portable for making high-volume and difficult-toreach terminal installations in a snap. The BAT22-6 delivers 1.5 tons of crimping force with an easy, pushbutton trigger. The lightweight, ergonomic design minimizes the risk of repetitive motion injuries that can occur with traditional hand crimping tools. And at less than three pounds, onehand operation is easy while still packing enough power to crimp up to 6 AWG terminals in seconds. Included Accessories Sturdy, plastic carrying case for portability Two 9.6V NiCd batteries and battery charger Sturdy tray for convenient storage of crimp dies Uses the exact dies of the Comfort Crimp line of ergonomic tools for Sta-Kon, Spec-Kon and Dragon Tooth terminals. Interchangeable dies can be quickly changed to crimp non-insulated and insulated terminals up to 6 AWG Dies are the same as our hand tools crimps will be exactly the same between Sta-Kon hand tools such as our ERG2001 and the BAT22-6 360 rotating head gives the user the added flexibility when crimping hard-toreach connections Short cycle time equates to crimping times of less than two seconds Quick, lightweight and maneuverable NiCd battery operation provides long-lasting battery life to complete up to 150 crimps on a single charge Extra battery and charger are included with the tool, ensuring round-the-clock operation Battery charger provides full battery life in under an hour Linear crimping motion gives a symmetric, high-quality crimp every time Installing Range: Up to 6 AWG Output Force: 1.5 tons Dimensions (L x W x H): 25.4" x 3.1" x 2.1" Battery: 9.6V NiCd Weight with Battery: 2 3 4 lbs. BAT22-6 Battery Crimping Tool 1.5 Ton with 120 VAC Charger 1 Crimp Dies* DIE1801 22 F,L,R-1 Series 1 DIE1802 22L002 1 DIE1804 22L004 1 DIE1806 22 F,L,R-6 Series 1 Tool purchase includes crimping tool, two 9V batteries, charger and case. * Dies sold separately. 36

Air-Operated Crimping Tools Perfect for high-speed installation! BAIR22-6 Heavy-Duty Bench-Top Air Crimp Tool Bench mounted for stability and operator control Compact size, all-metallic construction Delivers 1.8 tons of crimping force at 100 psi Heavy-duty and installs wide range of Dragon Tooth connectors....... Specifications........ Installing Range: Up to 6 AWG Output Force: 1.8 tons Operating Pressure: 85 to 100 psi Dimensions (L x W x H): 8" x 8" x 12" Weight without Dies: 17 lbs. BAIR22-6 BAIR22-6 Equipped with Shure-Stake Mechanism, 1 Ensuring Full Crimp Cycle Before Release Pneumatic power! PAIR22-6 Heavy-Duty Portable Air Crimp Tool Installs Dragon Tooth terminals Hand actuated Delivers 1.25 tons of crimping force at 100 psi 3 interchangeable dies can crimp the 22xxx1, 22xxx2, and 22xxx6 series terminals Installing Dies for BAIR22-6 and PAIR22-6 Crimp Dies* DIE1801 22 F,L,R-1 Series 1 DIE1802 22L002 1 DIE1804 22L004 1 DIE1806 22 F,L,R-6 Series 1............... Specifications.............. Installing Range: Up to 6 AWG Output Force: 1.25 tons Operating Pressure: 90 to 100 psi Dimensions (Dia. x L): 2 1 4" x 14" Weight without Dies: 2.5 lbs. PAIR22-6 PAIR22-6 Open C Yoke; Hand Actuated 1 Continuous reel crimping! Auto-Feed Tool for Magnet Wire Connectors on Strip Foot pedal contains T&B Shure-Stake control mechanism, which ensures a full compression each time Insulation piercing connectors are fed on a continuous reel-mounted strip Dies are self-contained Includes foot valve, hoses and air treatment system Pneumatic bench-mounted foot-operated tool for crimping copper or aluminum magnet wire and copper lead wire (not solder dipped or bonded) CAT. NO. CONNECTOR QUANTITY PER REEL WEIGHT WIDTH DEPTH HEIGHT 13676A 220004 9,000 19 lbs. 5" 14" 11" 13678 220001 3,000 28 lbs. 6" 18" 14" 13679 220002 3,000 28 lbs. 6" 18" 14" 13696 220006 2,500 32 lbs. 6" 18" 16" 37

Hydraulic Crimping Tools 6-Ton Hydraulic Head Lightweight but powerful compression tool Dies ordered as a two-piece set 14-Ton Hydraulic Head Rugged design, made to last in field or on bench C-yoke provides maximum flexibility for crimping Operates on 10,000 psi hydraulic pumps Output Force: 6 tons Operating Pressure: 10,000 psi nominal Dimensions (L x W x H): 12" x 2 1 4" x 3 9 16" Weight without Dies: 6.5 lbs. Output Force: 14 tons Operating Pressure: 10,000 psi nominal Dimensions (L x W x H): 11 1 2" x 2 1 2" x 4 1 4" Weight without Dies: 10 lbs. TBM6H 6-Ton Hydraulic Head with Steel Case 1 See die chart on page 39 for complete listing of dies and connectors used with TBM6H. CAT. NO. DESCRIPTION PKG. QTY 13100A Remote 14-Ton Hydraulic Head (Dies Ordered Separately) 1 See die chart on page 39 for complete listing of dies and connectors used with 13100A. 12-Ton Hydraulic Head 15-Ton Hydraulic Head 12 tons output (nominal) 10,000 psi max. hydraulic operating pressure Weighs 15 lbs. Longer, slimmer profile enables easier access into tight spaces Wider jaw opening eases crimping of larger connectors Features an insulated head for safety Output Force: 12 tons Operating Pressure: 10,000 psi nominal Dimensions (L x W): 14 1 2" x 3 1 4" Weight without Dies: 15 lbs. Output Force: 15 tons Operating Pressure: 10,000 psi nominal Dimensions (L x W x H): 15 3 4" x 2 5 8" x 4 3 8" Weight without Dies: 15.5 lbs. 13400 12-Ton Hydraulic Head (Dies Ordered Separately) 1 See die chart on page 39 for complete listing of dies and connectors used with 13400. CAT. NO. DESCRIPTION PKG. QTY TBM15I 15-Ton Insulated Hydraulic Head with Steel Case 1 See die chart on page 39 for complete listing of dies and connectors used with TBM15. 38

Hydraulic Pumps, Installing Dies Electric Hydraulic Pump Up to 10,000 psi output pressure Durable construction Hand or foot actuated 13610A 13810 13600 13810 Electric hydraulic pump, 10000 psi with Shure-Stake 1 mechanism feature; this is a heavy-duty OEM pump with high flow rate; 115V, 60Hz, 1 1 2 HP, 23A; requires hand or foot control. 13600 This electric hydraulic pump is for use with all T&B 1 hydraulic heads consists of pump with pressure gauge and Pioneer type male coupler; add suffix WG to eliminate gauge; output pressure 9800 psi; order switch and hose separately. A remote control switch is required. Order Cat. No. 13620 for hand operation or Cat. No. 13589A for foot operation. All pumps are supplied with a metal carrying case. 13610A Shure-Stake electric hydraulic pump has same features 1 as 13600, but includes the Shure-Stake control mechanism; prevents under crimping; (pump pressure must reach 9,800 psi before recycling); requires hand or foot control; order switch and hose separately. A remote control switch is required to operate this unit. Use either a #13611 (hand) or #13612 (foot) switch. You may also need for 13600 13620 Hand Switch 10 ft. 1 13589A Foot Switch 10 ft. 1 13619 10 ft. Non-Metallic Hose 1 13618 20 ft. Non-Metallic Hose 1 13600S Sled type stand for 13600 pump 1 You may also need for 13610A & 13810 13611 Hand Switch 10 ft. 1 13612 Foot Switch 10 ft. 1 13619 10 ft. Non-Metallic Hose 1 13618 20 ft. Non-Metallic Hose 1 Tool and Die Cross Reference Chart TBM6H 13100A 13400 TBM15I CONNECTOR DIES 204210MT 13682 204210S 13671B 13671A 13671B with 15500TB 204210SH 13673B 13673 13673B with 15500TB 204210-1 13671B 13671A 13671B with 15500TB 204210-1H 13673B 13673 13673B with 15500TB 204210-2 13671B 13671A 13671B with 15500TB 204210-3 13671B 13671A 13671B with 15500TB 204210-3H 13673B 13673 13673B with 15500TB 204210-5 13671B 13671A 13671B with 15500TB 204212 13671B 13671 13671B with 15500TB 204217 13671B 13671A 13671B with 15500TB 204MT14 204MT38 204T14 13689B 13689B with 15500TB 204T38 13689B 13689B with 15500TB 210214MT 13681B 13681 13681B with 15500TB 210214S 13670B 13670A 13670B with 15500TB 210214-2 13670B 13670A 13670B with 15500TB 210214-3 13670B 13670A 13670B with 15500TB 210216, 210216F 13670B 13670A 13670B with 15500TB 210217, 210217F 13670B 13670A 13670B with 15500TB 210219, 210219F 13670B 13670A 13670B with 15500TB 210MT14 210MT38 214420 220001 220002-TB 22000 22000 220006 220015 13713B 13713 220016 13713B 13713 220017 13713B 13713 220018 13713B 13713 220019 13713B 13713 220020 13713B 13713 220021 13713B 13713 220022 13713B 13713 220023 13713B 13713 220024 13713B 13713 220025 13713B 13713 220026 13713B 13713 22F061 22F066 22F081 22F086 22F101 22F106 22L001 22L002 22L004 22L006 22L008 6TON-MW-08 13683B 13683 13683B with 15500TB 22L009 6TON-MW-09 13684B 13684 13684B with 15500TB 22L009H 13686B 13686 13686B with 15500TB 22LF01 22LF06 22LM01 22LM06 22R061 22R106 22R146 314118S 13685B 13685 13685B with 15500TB 314123 13685B 13685 13685B with 15500TB 314125 13685B 13685 13685B with 15500TB 22L010 13690B 39

One-Piece and Two-Piece Connector Tools and Dies WT440 and WT540 Ratchet Hand Tools WT740 Standard Hand Tool WT440 Parallel-action hand tool NON-INSULATED INSULATED MIL-specified DIE OUTER SLEEVE COLOR OUTER SLEEVE NO. CONNECTOR CODE CONNECTOR Frame, with the option 4419 GSC-101 TIN of interchangeable steel dies 4400 GSC-128 BLUE GSR-101 4401 GSC-149 PURPLE GSR-128 A versatile tool, one 4402 GSC-156 YELLOW frame with a selection of dies covers the whole 4403 GSC-175 BLUE GSR-149 range of shield diameters GSC-187 ORANGE in the Hexagonal Range 4406 GSC-194 RED GSC-199 TIN GSR-156 Shure-Stake mechanism: once pressing has started, GSC-205 YELLOW 4408 the tool can be re-opened GSC-219 GREEN GSR-175 only after successful 4409 GSC-225 PURPLE completion of the crimping GSC-232 GSR-187 cycle 4410 ORANGE GSR-194 Supplied in a wooden box GSR-199 containing 1 frame (dies GSR-205 to be ordered separately) 4411 YELLOW GSR-219 GSC-261 GSR-225 4412 GSC-275 TIN GSR-232 GSC-281 PURPLE 4414 GSC-287 BLUE GSC-297 GREEN GSR-261 4415 GSC-312 YELLOW GSR-275 4416 GSC-327 TIN GSR-281.. Specifications.. 4417 ORANGE GSR-287 WT440 GSC-348 GSR-297 5450 GSC-359 PURPLE Length: 8" 5451 GSC-375 YELLOW GSR-312 Weight without dies: 1.0 lbs RED GSR-327 5452 GSC-405 RED GSR-348 Dies: Series 4400 GSC-415 BLUE GSR-359 WT540 5453 GSR-375 Length: 10.4" 5454 GSC-425 TIN Weight without dies: GSR-405 1.19 lbs. 5455 GSR-415 Dies: Series 5450 5456 GSC-460 TIN - 5457 GSC-500 GREEN - 5458 GSR-460 5459 GSR-500 CAT. NO. DESCRIPTION STD PKG. WT440 Ratchet Hand Tool 1 WT540 Ratchet Hand Tool 1 MIL specified Parallel action crimp Metal frame with plastic grip handles Can be used only with plastic dies (see page 41) All the dies are easily interchangeable Shure-Stake mechanism: once pressing has commenced, the tool can be re-opened only after successful completion of the crimping cycle Supplied in a wooden box containing one tool (dies to be ordered separately) Dimensions (L x W x H): 10" x 3.82" x.47" Weight without Dies: 1.75 lbs. CAT. NO. DESCRIPTION STD. PKG. WT740 Standard Hand Tool 1 Ergonomic Hand Tool Ergonomic hand tool Robust construction: metallic frame, partially covered with plastic Can be used either with plastic dies (see page 41) for small volume or with metal dies (see page 41) for medium to high volume applications All dies are easily interchangeable Supplied in a plastic Parallel action crimp case with 1 tool, 1 benchmount stand for easier use in volume Shure-Stake mechanism: production and 1 gauge (Cat. once pressing has commenced, No. RSK-LEHRE) for instant the tool can be re-opened only selection of the die and the after successful completion connector to be used of the crimping cycle Dimensions of Tool (L x W x H): 8.27" x 6.1" x.98" Weight of Tool without Dies: 1.04 lbs. Dimensions of Case (L x W x H): 9.65" x 8.27" x 2.17" Weight of Case & Tools: 2.05 lbs. Weight of Kit (case, tool and dies): 2.65 lbs. CAT. NO. DESCRIPTION STD. PKG. ERG740 Ergonomic Hand Tool 1 ERG740-01 Ergonomic Hand Tool Kit. includes plastic case with 1 tool, 1 1 benchmount stand for easier use in mass production, 1 RSK-LEHRE gauge for instant selection of the die, and 4 metal dies: D-101A, D-201C, D-301J, D-401M. 40

One-Piece and Two-Piece Connector Tools and Dies Plastic Dies for ERG740 and WT740 Ideal for small volume productions (up to a few hundred cycles maximum): prototyping, repair, etc. Made of high quality polymer in the same color as the corresponding connector Go/no-go gauges available (to be ordered separately) to inspect the wearing condition Product Ref. is marked on the upper part and on the lower part of the die set Weight approximately.71 oz. DIE SHIELD FOR GAUGE STD. CAT. NO. DIE COLOR DIAMETER (IN.) CONNECTOR CAT. NO. PKG. 101A Red.050.070 RSK 101 Red 101AG 1 101B Red.071.089 RSK 101 Red 101BG 1 201C Blue.090.100 RSK 202 Blue 201CG 1 201D Blue.101.118 RSK 202 Blue 201DG 1 201E Blue.119.131 RSK 202 Blue 201EG 1 201F Blue.132.143 RSK 202 Blue 201FG 1 301G Yellow.144.162 RSK 301 Yellow 301GG 1 301H Yellow.163.185 RSK 301 Yellow 301HG 1 301J Yellow.186.201 RSK 301 Yellow 301JG 1 401K Green.202.230 RSK 401 Green 401KG 1 401L Green.231.250 RSK 401 Green 401LG 1 401M Green.251.275 RSK 401 Green 401MG 1 401N Green.276.300 RSK 401 Green 401NG 1 Metal Dies for ERG740 For mass production and medium to high volumes Made of hardened steel does not wear Only for the ERG740 hand tool Product Ref. is engraved on the upper part and on the lower part of the die set Marked with a dot having the same color as the corresponding connector Weight approximately 2.6 oz. DIE SHIELD FOR STD. CAT. NO. DIE COLOR DIAMETER (IN.) CONNECTOR PKG. D-101A Red.050.070 RSK 101 Red 1 D-101B Red.071.089 RSK 101 Red 1 D-201C Blue.090.100 RSK 202 Blue 1 D-201D Blue.101.118 RSK 202 Blue 1 D-201E Blue.119.131 RSK 202 Blue 1 D-201F Blue.132.143 RSK 202 Blue 1 D-301G Yellow.144.162 RSK 301 Yellow 1 D-301H Yellow.163.185 RSK 301 Yellow 1 D-301J Yellow.186.201 RSK 301 Yellow 1 D-401K Green.202.230 RSK 401 Green 1 D-401L Green.231.250 RSK 401 Green 1 D-401M Green.251.275 RSK 401 Green 1 D-401N Green.276.300 RSK 401 Green 1 Hydraulic Head Installing Tool All the 2-piece Shield-Kon in the circular range need to be crimped with the 13640 hydraulic head equipped with the appropriate die. 3.5 ton nominal pressure (output) For 2-piece Shield-Kon terminals in the circular range Coupling for quick assembly Requires a 9,800 psi (approx. 690 bar) operating service pressure Quick interchangeable steel dies (to be ordered separately) Interlace die with 360 compression provides uniform pressure around circumference of connector FOR CONNECTOR DIE NOS. COLOR (INNER/OUTER) FOR 13640 CODE GSB430/GSC590 GS590 Red GSB550/GSC710 GS710 Blue GSB670/GSC840 GS840 Gray GSB810/GSC1010 GS1010 Brown GSB920/GSC1130 GS1130 Green GSB1040/GSC1250 GS1250 Pink GSB1122/GSC1332 GS1332 Orange GSB1224/GSC1440 GS1440 Purple GSB1353/GSC1563 GS1563 Yellow GSB1425/GSC1670 GS1670 Red CAT. NO. DESCRIPTION STD. PKG 13640 Installing Head 1 (order dies separately) 13606 Hand-Foot Pump 1 13600 Electric Hydraulic Pump 1 13620 Hand Switch 1 13589A Foot Switch 1 13619 Hydraulic Hose 10 ft. 1 13760 Air-Operated Hydraulic Pump 1 41

Cable Tie Installation Tools The most comfortable and efficient hand tool available for installing cable ties! Ty-Rap Cable Tie Installation Tool Thomas & Betts set out to develop a high performance and very reliable hand-operated cable tie installation tool. It s ergonomic with more features than any competing tool on the market. This new and improved Ty-Rap Cable Tie Installation Tool is the result, and it fits the bill in every aspect. Our engineers carefully considered user comfort and designed this rugged yet lightweight, well-balanced tool to reduce stress, fatigue and cumulative trauma disorders to the hand and wrist. They didn t stop with ergonomics, however. This new tool offers a flush cable tie tail-to-head trim, a longer handle stroke requiring less handle force, higher tension capabilities and much, much more! Designed for Efficiency Wide cable-tie insertion gap makes it easier to insert tie into tool Tension adjustment wheel on nose offers easy access and quick setting about five times faster than competing tools! Tension-locking mechanism maintains constant tension setting, even when tool is frequently put down and picked up again Flush tail-to-head cut-off eliminates sharp cable tie ends that can cut or scratch installers, wires and nearby devices Longest stroke length available on the market a full 1" means fewer handle-tensioning cycles to save time and lower installation costs Designed for Comfort 360 rotating nose offers maximum flexibility in any position, especially in tight spaces no twisting of tool required! Adjustable grip span adapts to fit large or small hands Anti-recoil cut-off mechanism reduces shock and vibration to hand and wrist High-low handle travel feature offers lowest handle force with highest tension in any hand-operated cable tie installation tool on the market Handles constructed from rugged, lightweight, high-impact polymer in a balanced design with soft, over-molded, round-edged grips for added user comfort Dimensions (L x H x W): 7" x 5" x 1 5 8" Weight: 9 oz. STD. ERG50 Tool for 18 50 lb. (80 222 N) Cable Ties 1 ERG120 Tool for 50 120 lb. (222 533 N) Cable Ties 1 42

Cable Tie Installation Tools Lightweight. Economical. Durable. Perfect for spot-tying! Ty-Rap Cable Tie Installation Tool Light Duty Installs Ty-Rap cable ties up to.301" wide by.080" thick Designed for use by both left- and right-handed operators Lightweight, high-impact polymer and steel components These tools cinch up the tie with a squeeze action and cut away the excess tail when twisted 180. A specially designed pawl cuts away the tail if the tension limit is exceeded, thereby preventing the cable tie from being over-tightened. TIE BODY STD. CAT. NO. DESCRIPTION WIDTH IN./MM. PKG. QTY. WT1-TB Cable Tie Installation Tool, 18 50 lbs.(80 222 N).09.18/2.39 4.67 1 WT2-TB Cable Tie Installation Tool, 50 120 lbs.(222 533 N).18.301/4.67 7.65 1 Cuts tail off flush. Ty-Rap Cable Tie Installation Tool Metallic Installs Ty-Rap cable ties Rugged metallic construction Pistol-grip installation tool Easy tension adjustment Tensions and cuts tie tail off flush TIE BODY STD. CAT. NO. DESCRIPTION WIDTH IN./MM. PKG. QTY. WT193A Cable Tie Installation Tool, 18 50 lbs. (80-222 N).09.18/2.39 4.67 1 Easy tension adjustment! Ty-Rap Heavy-Duty Installation Tool Mil Spec Approved Installs Ty-Rap cable ties Rugged metallic construction Pistol-grip installation tool Tensions and cuts cable tie tail off flush Get the job done right! Ty-Rap Heavy-Duty Installation Tool Stainless Steel Installs Ty-Rap stainless steel cable ties Rugged stainless steel construction Pistol-type installation tool Adjustable tension settings TIE BODY STD. CAT. NO. DESCRIPTION WIDTH IN./MM. PKG. QTY. DAS250 Stainless Steel Installation Tool up to.31/7.87 1 Makes tie installation easy! Ty-Rap Installation Tool Deltec & Stainless Steel Ties WT3D Installs both self-locking Ty-Rap cable ties and lashing ties WT3S Installs stainless steel ties TIE BODY STD. CAT. NO. DESCRIPTION WIDTH IN./MM. PKG. QTY. WT199 Installation Tool, 18 50 lbs. (80 222 N).09.18/2.39 4.67 1 WT197 Installation Tool, 50 120 lbs. (222 533 N).18.30/4.67 7.65 1 * Mil Spec Approved (WT199 MS90387-1, WT197 MS90387-2) TIE BODY STD. CAT. NO. DESCRIPTION WIDTH IN./MM. PKG. QTY. WT3D Deltec Installation Tool.18.50/4.67 12.70 1 WT3S Stainless Steel Installation Tool up to.50/12.70 1 NOTE: Tensions only 43

Cable Tie Installation Tools Quality stainless steel tools for tensioning and installing. Tensioning Tools For tensioning Reusable Ties and Multi-Lok Ties WTAE201 Tensioning Hook WTAE200 Cable Tie Tensioner WEIGHT STD. CAT. NO. DESCRIPTION LBS./KG. PKG. QTY. WTAE200 Cable Tie Tensioner.6/.27 1 WTAE201 Tensioning Hook.1/.05 1 Apply tension, cut and secure with confidence! Installation Tools WTC075 Designed to install 1 4" to 5 8" wide Free-End Clamps. The lightweight, ratchet-action tool tension cuts and secures the buckle tab. WTC001 A drop-forged tool with tensioning capability to do all 1 4" to 3 4" Free-End Clamp sizes. WTJ020 Lightweight pocket-sized tool to install 1 4" and 3 8" wide Free-End Clamps. This tool also applies tension and has a built-in cutter. WEIGHT STD. CAT. NO. DESCRIPTION LBS./KG. PKG. QTY. WTJ020 Compact Free End Stainless Steel Cable Tie Installation Tool for 1 4" to 3 8" sizes 1.1/.50 1 WTC075 Pistol Grip Free End Stainless Steel Cable Tie Installation Tool for 1 4" to 5 8" sizes 2.6/1.18 1 WTC001 Free End Stainless Steel Cable Tie Installation Tool For All Sizes 4.4/2.00 1 High-carbon, Teflon coated steel blade! SR-100 Cutting Tool Contoured handle resists tube crushing Produces no sawdust no need to debur Lightweight, low-profile and no exposed blade when stored Use our SR-100 cutting tool for all your spiral wrap, plastic pipe and PVC conduit needs up to 1 1 4" I.D. STD. SR-100 Cutting Tool 1 Teflon is a registered trademark of the DuPont Corporation. 44

Cutting Tools The wiring duct tools you need for every application! Duct Cutting Tools for a clean professional finish Finger Cutting Tools that make modifications simple Notching Tools for duct sidewalls to facilitate tee and corner junctions Bench-Mount Cutting Tools for fast, high volume duct cutting Rivet Installation Tools for quick duct mounting Lightweight and durable! Duct/Cover Cutting Tool Cut duct fingers easily! Finger Cutting Tool Improved Performance! All-steel construction Sharp cutting surface Replaceable blades available Rugged die-cast construction with insulated handles for a comfortable, non-slip grip Removes duct fingers in tight places Works with all slotted wiring duct Also cuts round and solid wall duct Spring loaded for ease of use CAT. NO. DESCRIPTION STD. PKG. QTY. SX-15TB Handheld Duct Cutter 1 CAT. NO. DESCRIPTION STD. PKG. QTY. DK-65TB Duct Finger Cutter 1 45

Cutting and Other Tools For fast, high volume duct cutting! Bench-Mount Cutting Tool Engineered for use with Ty-Duct plastic wiring ducts and covers All-steel construction lasts for years Adjustable gauge sets the desired length of duct Easy-to-read measuring indicator Adjustable stop for easy repeated cutting Sharp, easy-to-replace blades CAT. NO. DESCRIPTION STD. PKG. QTY. DC-125TB Bench-Mount Duct Cutter 1 Notch duct sidewalls fast! Notching Tool Mount ducts quickly! Rivet Installation Tool Notches sidewalls to bottom scoreline Facilitates tee and corner junctions Rugged design Easy to use Spring loaded Use for setting duct rivets Pressure on the tool head secures the rivet in place CAT. NO. DESCRIPTION STD. PKG. QTY. DNT-100TB Duct Notching Tool 1 CAT. NO. DESCRIPTION STD. PKG. QTY. 08205 08200 Series Rivet Installation Tool 1 46

Heat Guns and Torches Electric Heat Gun UL/CSA approved 450 F to 1,000 F heat range 120VAC 60Hz CAT. NO. DESCRIPTION STD. PKG. QTY. WT1400 Dual Temp. heat gun. 600 F/900 F, 1 1,300W, 120VAC 60Hz Separate fuel and air flow controls enable precise adjustment of flame and temperature up to 2,500 F! Portable Heat-Shrink Torch 2,500 F output capacity satisfies virtually any heatshrink, brazing or soldering requirement Dual fuel- and air-flow controls enable separate adjustment of temperature and flame precision Brass and steel construction provides durability Operates on standard butane lighter fluid Air-Flow Control Ergonomic Rubber Grip Safety Lock (push and turn to lock or unlock) Automatic- Ignition Start Button Kill-Switch Button Fuel-Flow Control Removable Base Fuel Tank Capacity: 2.03 fl. oz. Operating Time (per full fuel tank): Up to 220 minutes Dimensions (without base): 3.9"L x 1.4"W x 5.4"H Weight (when filled): 9.88 oz. Heavy-Duty Self-Igniting Torch The Shrink-Kon Torch is engineered to provide years of long, dependable and efficient service. The body is constructed of strong, lightweight cast aluminum; burn tube and conduit of stainless steel; venturi, orifice and burn tips of solid brass. Two separate burn tips are available: one for heat-shrinkable tubing, one for brazing and soldering. Trigger ignition lights the Shrink-Kon Torch automatically no flints, batteries or strikers to wear out its piezo electric crystal provides over 30,000 ignitions before servicing, generating 24,000 volts to ignite the torch instantly Torch easily screws to all commercially available 14- and 16-oz. propane cylinders Single hand ignition makes shrinking, brazing and soldering fast, easy and efficient at all angles, even upside down and in windy conditions Built-in pressure regulator provides a constant gas flow rate in all positions, so your torch won t flare out when you need it most CAT. NO. DESCRIPTION STD. PKG. QTY. WT-PTORCH Shrink-Kon Portable Heat-Shrink Torch* 1 CAT. NO. DESCRIPTION STD. PKG. QTY. SIT-1 Shrink-Kon Torch for 14- or 16-oz. cylinders 1 SIT-2 Adapter and 5-foot extension hose 1 47

Index of Tools (by catalog number) CAT. NO. PAGE NO. CAT. NO. PAGE NO. CAT. NO. PAGE NO. CAT. NO. PAGE NO. CAT. NO. PAGE NO. Index BAIR22-6...29, 37 BAT22-6...28, 36 BCS8-40...14 BCT840...13 BCT840S...13 BPLT13970DC...11 BPLT13970FS...11 BPLT13970P2...11 BPLT13970RB...11 BPLT13970RP...11 BPLT14BSCR...9 BPLT14BSCRI...9 BPLT15BSCR...10 BPLT54BSCT...15 BPLT58BSCT...16 BPLT62500BSCR...4 BPLT62BSCR...4 BPLT6BSCR...5 BY55...16 CSR750...15 CTR-1...16 D-101A...41 D-101B...41 D-201C...41 D-201D...41 D-201E...41 D-201F...41 D-301G...41 D-301H...41 D-301J...41 D-401K...41 D-401L...41 D-401M...41 D-401N...41 DAS250...43 DBL...21 DC-125TB...46 DIE1801...36, 37 DIE1802...36, 37 DIE1804...36, 37 DIE1806...36, 37 DIE2001...28, 29 DIE2002...28, 29 DIE2005...28, 29 DIE2007...28, 29 DK-65TB...45 DNT-100TB...46 DWS02...22 ERG120...42 ERG1255...25 ERG1801...36 ERG1802...36 ERG1804...36 ERG1806...36 ERG1-WS...22 ERG2001...24 ERG2002...24 ERG2004...24 ERG2005...24 ERG2006...24, 25 ERG2007...24 ERG2008...24 ERG50...42 ERG740...40 ERG740-01...40 ERG811...36 JB12B...6 OD581...16 OJB...21 PAIR22-6...29, 37 SBC-1...22 SIT-1...47 SIT-2...47 SR-100...44 SWS01...22 SX-15TB...45 TBM12...6 TBM12D-1...18, 20 TBM12D-2...18, 20 TBM12D-3...18, 20 TBM12D-4...18, 20, 21 TBM12D-5...18 TBM12D-H...21 TBM14M...8 TBM14MC...8 TBM15I...10, 38 TBM25S...2 TBM40HC...14 TBM40HCRH...16 TBM4S...2 TBM54BSCT...15 TBM54BSCTS...15 TBM58BSCT...16 TBM5S...2 TBM5SV...13 TBM5V...13 TBM6...26 TBM6221...19, 20 TBM6224...19, 20 TBM6229...19, 20 TBM6233...19, 20 TBM6237...19, 20 TBM6242...19, 20 TBM6245...19, 20 TBM6250...19, 20 TBM6254...19, 20 TBM6260...19 TBM6262...19, 20 TBM6266...19 TBM6271...19 TBM6276...19 TBM6280...19 TBM6287...19 TBM6H...5, 38 TBM6HD-1...5 TBM6S...3, 26 TBM8-750...7 TBM8-750BSCR...7 TBM8-750M-1...7 TBM8S...3 TBMODBSCR...16 VBC-1...22 WT110M...23 WT111M...23 WT112M...23 WT115A...26 WT129...25 WT1377...25 WT1400...47 WT161M...23 WT193A...43 WT197...43 WT199...43 WT1-TB...43 WT2000...23 WT2130A...25 WT2-TB...43 WT3185...25 WT3D...43 WT3S...43 WT440...40 WT550...40 WT740...40 WTAE200...44 WTAE201...44 WTC001...44 WTC075...44 WTJ020...44 WT-PTORCH...47 6TON21...19, 20 6TON24...19, 20 6TON29...19, 20 6TON33...19, 20 6TON37...19, 20 6TON37R...20 6TON42...19, 20 6TON45...19, 20 6TON50...19, 20, 21 6TON54...19, 20 6TON60...19 6TON62...19, 20 6TON66...19 6TON71...19 6TON71R...20 6TON76...19 6TON80...19 6TON87...19 6TON94...19 15C125R...21 15CA106R...21 15CA29R...21 15CA33R...21 15CA37R...21 15CA37RCH...20 15CA42R...21 15CA45R...21 15CA49R...21 15CA54R...21 15CA60R...21 15CA66R...21 15CA71R...21 15CA71RCH...20 15CA76R...21 15CA80RCH...20 15CA87R...21 15CA94R...21 15G121R...21 15G126R...21 15G86R...21 40C...16 101A...41 101B...41 156CS...16 201C...41 201D...41 201E...41 201F...41 295-31365...3 295-31365M...3 297-31669-7...19 297-32136...16 301G...41 301H...41 301J...41 364RF...14 366RF...14 368-CK...14 401K...41 401L...41 401M...41 401N...41 683-54335...27 08205...46 11308...19 11333...19 11334...19 11363...19 11364...19 11401...19 11402...19 11405...19 11406...19 11407...19 11408...19 11409...19 11410...19 11416...19 11418...19 11419...19 11423...19 11424...19 11425...19 11426...19 11732...18, 31, 35 11733...18, 31, 35 11734...18, 31 11735...18, 31, 35 11736...18, 31, 35 11737...18, 31, 35 11738...18, 31, 35 11739...18, 31, 35 11740...18, 31, 35 11741...18 11742...18 11743...18 11744...18, 20 11745...18 11746-TB...18, 20 11747...18 11748...18, 20 11749...18, 20 11750...18 11751...18 11753...18, 20 11771...18, 31, 35 11781M...31, 35 11782M...31, 35 11783M...31 11784M...31, 35 11785M...31, 35 11786M...31, 35 11787M...31, 35 11788M...31, 35 11789M...31, 35 11802...26 11803...26 11805...26 11806...26 11807...26 11808...26 11809...26 11810...26 11811...26 11821...26, 35 11822...26, 35 11823...26, 35 11824...26, 35 11825...26, 35 11826...26, 35 11827...26, 35 11828...26, 35 11829...26, 35 12050...27 12051...27 12052...27 12054...27 12055...27 12056...27 12057...27 12058...27 12059...27 12060...27 12061...27 12062...27 13100A...9, 38 13400...31, 38 13454...2, 18, 20 13455...2, 18, 20, 21 13456...2, 18, 20 13457...2, 18 13458...2, 18 13461...3, 18, 20 13462...3, 18, 20, 21 13463...3, 18, 20 13464...3, 18 13465...3, 18 13466...3, 18 13467...3, 18 13468...3, 18 13470...21 13471...21 13472...3, 18, 20 13473...3, 18, 20 13474...3, 18, 20, 21 13475...3, 18, 20 13476...3, 18, 20 13477...3, 18, 20, 21 13478...18, 20 13479...18 13589A...12, 32, 39, 41 13600...12, 32, 39, 41 13600S...12, 32, 39 13604...11 13606...11, 41 13610A...12, 32, 39 13611...12, 13, 32, 39 13612...12, 13, 32, 39 13613...32, 39 13614...13 13618...12, 13, 32, 39 13619...12, 13, 32, 39, 41 13620...12, 32, 39, 41 13640...41 13642M...6, 31 13643...31 13644...31 13645...31 13650...31, 35 13651...35 13652...35 13653...35 13654...31, 35 13655...31, 35 13656...31, 35 13657...31, 35 13658...31, 35 13659...31, 35 13676A...37 13678...37 13679...37 13696...37 13760...41 13797...32, 39 13798...13 13799...13 13810...13, 32, 39 15501A...21 15502...21 15504...19, 20 15505...19, 20 15506...19, 20 15508...19 15510-CK...19 15511...19 15512...19, 20 15513-CK...19 15514-CK...19 15515-CK...19, 20 15517...19 15520...19 15522...19 15526...19 15527-CK...19 15528...19 15530...19, 21 15532-CK...19 15534...19 15536-CK...19 15601...19 15602...19 15603...19 15606...19 15608...19 15609...19 15611...19 15612...21 15612CH...20 15620...21 15620CH...20 15620CHF...20 21061...13 21649...16 21707M...31, 35 21708M...31, 35 21709M...31, 35 21710M...31, 35 21711M...31, 35 21712M...31, 35 21713M...31, 35 21714M...31, 35 21715M...31, 35 21731...31, 35 21732...31, 35 21733...31, 35 21734...31, 35 21735...31, 35 21736...31 21737...31, 35 21738...31, 35 21739...31, 35 21740...31, 35 21741...31, 35 21940...10 25000...4, 30 74506...19 48

Tab Category Searches Using the Product, Brand and/or Selector Guide tab searches enables you to view T&B s entire product offering so you can best determine those items of interest to you. For the Latest Information, Visit Electrical World at tnb.com Quick Search Box If you know the T&B item you are searching for or a competitive part number, this quick search box is the best place to begin your search. T&B Catalog/UPC Search use this option when you know the exact T&B catalog number or its 11-digit UPC number. Competitor Part Number Search use this option when you know the exact competitor s catalog number but need to view T&B s equivalent product offering. NOTE: Users do NOT have to enter dashes, slashes and spaces when entering the part number simply enter the alphanumeric characters you are searching for. Limited Warranty for Tools Thomas & Betts sells tools with the understanding that the user will perform all necessary tests to determine the suitability of each tool for the user s intended application. Thomas & Betts warrants that its tools will be free from defects in materials and workmanship for the period of time specified in the chart on the inside front cover. Upon prompt notification of any warranted defect, Thomas & Betts will, at its option, repair or replace the defective product or refund the purchase price. Proof of purchase is required. Misuse or unauthorized modification of the product voids all warranties. Limitations and Exclusions The warranty to the left is the sole warranty concerning this product, and is in lieu of all other warranties express or implied, including but not limited to any implied warranty of merchantability or fitness for a particular purpose, which are specifically disclaimed. Liability for breach of the above warranty is limited to cost of repair or replacement of the product, and under no circumstances will Thomas & Betts be liable for any indirect, special, incidental or consequential damages. Direct all warranty inquiries to: Thomas & Betts 1-800-284-TOOL (8665).

Compression Connectors and Tools Terminal Products and Tools Insulation Piercing Connectors Grounding Connectors For U.S. Customer Service and Order Inquiries, Call 1-800-816-7809 or Fax 1-800-816-7810. Cable Fastening Systems For International Service and Order Inquiries, Call (U.S.) 901-252-5400 or Fax 901-252-1330. For Canadian Customer Service and Order Inquiries, Call 450-347-5318 or Fax 450-347-1976. Wiring Duct and Accessories For U.S. Technical Support, Call 1-888-862-3289 or Fax 901-252-1321. For International Technical Support, Call (U.S.) 901-252-5000, Enter 1, 6672. Wire and Connector Insulation Products For Tool Service and Repair, Call 1-800-284-TOOL (8665). Thomas & Betts Corporation Electrical Division 8155 T&B Boulevard Memphis, Tennessee 38125 Thomas & Betts Ltd. 700 Thomas Avenue Iberville, Québec J2X 2M9 2007 Thomas & Betts Corporation. All rights reserved. Specifications are subject to change without notice. Printed in U.S.A. 2/07/5M Order No. GM-396