GRUNDFOS ALLDOS DISINFECTION ALLDOS DISINFECTION SYSTEMS with Chlorine Gas 1 GRUNDFOS ALLDOS DISINFECTION
Content Applications 4-5 Page Geco 103-100 compact dosing unit 1 Vacuum regulator and dosing unit in one device for direct mounting on a chlorine gas cylinder Complete with injector, vacuum line and spare sealings 6 6 4 C 111/C 113 dosing system Continuous chlorine gas dosing without interrupting the process for manual or automatic control 5 2 2 7 2 vacuum regulators for mounting on chlorine gas cylinders Dosing unit for separate wall mounting The first cylinder being empty, the U 189 device changes immediately over to the next vacuum regulator at the full chlorine cylinder 3 4 6 C 117/GS 146 dosing system 8 Continuous gas dosing without interrupting the process for manual or automatic control 8b 8a 2 vacuum regulators for mounting 8 on gas drums, liquid traps avoid the penetration of liquefied gas 11 9 5 Separate installation of several dosing units 7 7 If the first drum is empty, the device changes immediately over to the 13 next vacuum regulator at the full gas drum 12 4 10 6 The safety valve avoids excess pressure in the vacuum lines leaving the dosing system 1 103-100 9 Display unit for empty signal 2 111-102/111-202 10 Gas sensor 3 113-110 11 Gas warning unit Gasdetect 4 Injector 545 12 Flowmeter with current signal output 5 Vacuum change-over unit U 189 13 Compact measuring system Conex Compact 6 Chlorine gas absorption cylinder 524 7 Vacuum regulator with liquid trap 8 Dosing unit with manual rate valve 8a 8b Dosing unit with electric servomotor Dosing untit with electric servomotor and current input
GS 140 Series High capacity disinfection system These innovative disinfection sytems dispose of modern sensors and microprocessor electronics for the measurement of the chlorine concentration and the control of the dosing flow. A multitude of sensors offer in connection with PLC extensive possibilities of monitoring and early detection of faults in automated systems, and thus provide the utmost process safety. Structure Vacuum regulator with gas inlet valve and safety valve for installation in a gas tank room Dosing unit with flowmeter, linear adjustment valve and differential pressure controller for installation on the floor or at the wall Modern optional equipment for control, regulation, full-automatic operation and control Injectors especially developed for the new dosing system with utmost efficiency 9-10 16 16 2 2 3b 3b 3c 3c 4 4 18 18 7 7 8 8 9 9 17 17 15 15 16 16 5 5 1 1 1a 1a 14 14 6 6 16 16 17 17 11 11 12 12 10 10 13 13 Accessories 11-15 Change-over devices Chlorine header line Pressure reducing valve Injection Units Chlorine gas absorption cylinder Injectors Combined liquid chlorine trap Chlorine gas filter Drum support 1 Chlorine drum 5 Nitrogen flushing device 14 Chlorine gas sensor 1a Chlorine drum balance 6 Chlorine evaporator (Alldos safety system Gasdetect) 2 Control for the pneumatic chlorine 7 Pressure reducing valve and filter 15 Optical and acoustic alarm device drum quick-action stop valves 8 GS 141-148 vacuum regulator 16 Suction nozzle to the chlorine gas 3 Chlorine drum lifting device 9 GS 141-145 gas dosing system neutralization sytem 3a Lifting beam 10 High-capacity injector 17 Central control panel with computer 3b Spring balance for cranes 11 Motive water booster pump interface 3c Chain hoist 12 Flowmeter with 4-20 ma output 18 Sprinkling system 4 Automatic change-over device 13 Injection unit 3 GRUNDFOS ALLDOS DISINFECTION
Chlorine gas disinfection systems are used for drinking water treatment.
Applications Chlorine gas disinfection systems can be used for various purposes: Drinking water The most important application area for gas disinfection systems is in the drinking water sector, including the disinfection of raw water as well as the final disinfection after treatment process. Pool water disinfection Every swimmer adds 1.000.000 to 1.000.000.000 microorganisms to the water. The water itself contains microorganisms, as well. Chlorine gas is the effective and economic means for the disinfection of swimming pool water. Process water disinfection Chlorine gas can also be used for disinfection of process water to ensure that microbial contamination transmission from water is minimized. Cooling water treatment By disinfecting the cooling water you remove microorganisms that can affect the system. Waste water disinfection Waste water disinfection includes disinfection of industrial waste water and municipal waste water. It protects the public from potential exposure to pathogenic microorganisms that would otherwise be present in wastewater. 5 GRUNDFOS ALLDOS DISINFECTION
GECO 103-100 compact dosing unit 131.7 82.4 63 146 92 126 max. 168 71.1 101 31.4 ca. 197 14 40.3 Technical data Medium Chlorine gas Capacity range 5-100 g/h, 10-250 g/h, 25-500 g/h, 50-1000 g/h, 100-2000 g/h, 150-3000 g/h, 400-4000 g/h Adjustment ratio 1 : 20 Accuracy +/- 4 % Measuring device According to the floater principle, measuring tube 70 mm Empty indication Optical signal for lack of chlorine, automatic Materials Enclosure PVC Inlet valve Silver/PTFE, special alloy Springs Hastelloy C coated Diaphragm FEP Rate valve PVC O-rings Viton B Yoke Cast, nickel plated Connections Pressure gas USA yoke, option: union nut Vacuum safety line PE hose 8/11 Injector water connections ¾ hose / ¾ NPT up to 1000 g/h 1 hose / 1 NPT up to 2000 g/h 1 ¼ hose / 1 ¼ NPT up to 4000 g/h P max (water) Motive water pressure at the injector: 16 bar Backpressure at the injector outlet: 5 bar Weight 1,3 up to 2 kg Geco 103-100 variants Capacity Injector connection 5-100 g/h ¾ hose / ¾ NPT 10-250 g/h 25-500 g/h 50-100 g/h 100-2000 g/h 1 hose / 1 NPT 150-3000 g/h 1 ¼ hose / 1 ¼ NPT 400-4000 g/h Optional connections Union nut 1 Union nut G 5/8 Union nut G ¾ Optional accessories Manometer 0-16 bar, NG 63 Residual pressure control 2 bar Liquid trap, heating 230 V, cable with Euro plug Measurements in mm
C 111/C 113 dosing system 146 63 60.6 213.8 187.8 339.4 This systems consists of Vacuum regulator C 111-202 Single dosing regulator C 113-310 or 390 Vacuum regulator C 111-202 Connection Capacity union nut 1 max. 4 kg/h 31.4 C 111-202 with manometer With inlet valve and safety overpressure valve Prepared for manometer Optical empty indication 25 m of vacuum line (PE hose 8/11) with connections With gaskets for cylinder connection Optional connections 203.8 Union nut G 5/8 Union nut G 3/4 Union nut 1,03-14 Union nut 1 ¼ USA yoke Optional accessories 235.8 Manometer 0-16 bar, NG 63 with or without Min contact output Residual pressure control 2 bar Liquid trap, heating 230 V, cable with Euro plug Liquid trap, heating 115 V, cable with USA plug Vacuum regulator for serial installation Testing agents for tightness check 90 75 C 111-202 with liquid trap Single dosing regulator C 113-310/390 Capacity 2-40 g/h 5-100 g/h 10-250 g/h 25-500 g/h 50-1000 g/h 100-2000 g/h 150-3000 g/h 400-4000 g/h 400 For operation with vacuum regulator 111-202 With compensation regulator and measuring device 10 m of vacuum line (PE hose 8/11) Fixing material included 165 190 165 Dosing regulator C 113-390 with electric servomotor 6 6 25 40 105 130 C 113-310 C 113-310 Synchronous motor with limit switches, IP 55 enclosure Actuating time (0-100%): 109 s at 50 Hz, 87 s at 60 Hz Power consumption: 3 VA Standard: mains voltage of servomotor 230 V (50/60 Hz) Option: mains voltage 115 V - please indicate separately Option : different measuring range (please see tabel below) with servomotor with 4-20 ma input for proption control, manual/automatic switch, trimmer for zero point/limit value, keys for manual control open/close Measurements in mm 7 GRUNDFOS ALLDOS DISINFECTION
2 vom Vakuumregler from vacuum regulator du règulateur de dèpression zum Injektor to injector vers hydro-ejecteur C117/GS 146 dosing system Ø 6 Ø 6 This systems consists of Vacuum regulator GS 146-010 Single dosing regulator C 117-110 or 190 Dosing regulator C 117-110 Capacity 0,5-10 g/h 375 400 575 600 25-500 g/h 50-1000 g/h 100-2000 g/h 200-4000 g/h 300-6000 g/h 400-8000 g/h 105 130 Dosing regulator C 117-110 Ø 6 12.5 145 170 Dosing regulator 117-190 with servomotor For the operation with vacuum regulator 146-.. Mounted on a plate for wall mounting With manual rate valve and measuring device Vacuum connection for PE hose or PVC pipe Dosing regulator C 117-190 Capacity 0,5-10 g/h B 610 650 Synchronous motor with limit switches, enclosure IP 55 Actuating time (0-100%): 108 s at 50 Hz, 87 s at 60 Hz Power consumption: 3 VA Standard: mains voltage servomotor 230 V (50/60 Hz) Options: mains voltage 115 V please indicate separately Option: different measuring range with servomotor 4-20 ma input for proportional control, manual/automatic switch, trimmer for zero point/limit value, keys for manual open/close Cl 20 C 0.932 bar abs ALLDOS A Vacuum regulator GS 146-010 Connection Capacity 160 9 360 400 Dosing regulator C 117-390 Ø 9 200 75 PE 10/14 177 union nut 1 max. 10 kg/h With inlet valve and safety overpressure valve Overpressure connection for PE hose 8/11 Optional connection Union nut 1 Union nut G 5/8 Union nut G ¾ Union nut 1,03-14 Union nut 1 ¼ USA yoke 86 173 177 Ø172 59 Optional accessories Plate for wall mounting, incl. fixing material Manometer 0-16 bar, NG 63 Manometer 0-16 bar, NG 63, with Min contact output Liquid trap, heating 230 V, cable with Euro plug Liquid trap, heating 115 V, cable with USA plug GS 146-010 236 143 Different vacuum connection for the dosing unit - optional Connection for PE hose 10/14 Connection for PE hose 12/16 Connection for PVC pipe 12/16 Connection for PVC pipe 15/20 Measurements in mm
GS 140 Series This systems consists of Vacuum regulator GS 146, 147 or 148 Dosing regulator GS 141, 143 or 145 Additional accessories 610 390 209 52 20/25 1000 170.5 105.5 128 206 125 40/50 Ø 175 GS 147 6.6 DN 25 245 1810 DN 40=730 DN 20=760 50 450 GS 141-145 with foot for floor mounting Ø 50 170 6/8 170 1000 245 GS 148 DN 25 Vacuum regulator GS 146 and 148 GS 141-145 for wall mounting Technical data for line installation, with integrated safety valve, with grooved flange 1 DN 25 (G1 ), without liquid trap Chlorine gas Ammonia Sulphur dioxide Flow rate Vacuum connection Order No. Flow rate Vacuum connection Order No. Flow rate Vacuum connection Type No. max. 40 kg/h PVC pipe 20/25 147-040 max. 20 kg/h PVC pipe 20/25 147-020N max. 38 kg/h PVC pipe 20/25 147-038S max. 70 kg/h PVC pipe 40/50 148-070 max. 35 kg/h PVC pipe 40/50 148-035N max. 65 kg/h PVC pipe 40/50 148-065S max. 120 kg/h PVC pipe 40/50 148-120 max. 60 kg/h PVC pipe 40/50 148-060N max. 115 kg/h PVC pipe 40/50 148-115S max. 200 kg/h PVC pipe 40/50 148-200 max. 100 kg/h PVC pipe 40/50 148-100N max. 190 kg/h PVC pipe 40/50 148-190 S Manometer for Cl 2, 0-16 bar, NG 63, optionally with MIN contact (N.O./N.C.) without manometer, optionally prepared for pressure sensor Testing agents bottle with ammonia for tightness check (Cl 2, SO 2 ) sulphur strips for tightness check (NH 3 ) System types Vacuum dosing system with rate valve Gas flowmeter according to floater principle Vacuum meter NG 100 mm Manual adjustment of the dosing flow Differential pressure regulator Floor mounting unit, covered Measurements in mm 9 GRUNDFOS ALLDOS DISINFECTION
Dosing regulator GS 141/143/145 Chlorine gas (Cl 2 ) Dosing capacity Vacuum connections Type No. 10-200 g/h 25-500 g/h 50-1000 g/h 100-2000 g/h 200-4000 g/h 400-8000 g/h 0,5-10 kg/h 1-20 kg/h 2-40 kg/h 3,5-70 kg/h 6-120 kg/h 10-200 kg/h PE hose 10/14 141-010 PVC pipe 20/25 143-040 PVC pipe 40/50 145-200 Gas dosing system GS 141-145 Optional servomotor synchronous motor 3VA, IP 55, actuating time 0-100%: 90s at 50 Hz, 75 s at 60 Hz, installed on the rate valve 230 V (50/60 Hz), input/output 4-20 ma 115 V (50/60 Hz), input/output 4-20 ma Vacuum meter for injector vacuum NG 100 with 2 limit contact outputs Dosing system without vacuum meter Pressure sensors For injector vacuum For operating vacuum 2 pressure sensors (for injector and operating vacuum), signal evaluation via external PLC, required control voltage 24 V Enclosure versions Floor mounting unit with hood, open foot wall mounting unit with hood Optional vacuum connections (only GS 141) for PE hose 8/11, PE hose 12/16, PE hose ½, PVC pipe 12/16, PVC pipe 15/20 Chlorine gas disinfection systems ensure constant quality of your swimming pool water.
Accessories Vacuum change-over device U 189-010 Change-over device U 185-1 73 54 124 149.2 186 275 95.25 240.5 89 100 D2 75 383.5 160 867 Vacuum change-over device U 185-1 67 H 220.5 Ø 6.5 D1 262 Vacuum change-over device U 189 L D1 For combining 2 vacuum regulators with dosing regulators, vacuum connection PE hose 8/11 up to 4 kg/h, 10/14 up to 10 kg/h. 493 Option Additionally with 2 Reed contacts for remote transmission of the empty signal, max. 50 V/1 A/50 W Accessories empty signal Description Order No. Display unit for empty signal, 115 V 332-2012 Display unit for empty signal, 230 V 332-2015 Wall mounting enclosure for display unit 300-210 Change-over device U 186-120 217 86 43 Technical data 145 40 173 68 Connection PVC tube 32/40 Maximum flow up to 120 kg/h for Cl 2 up to 60 kg/h for NH 3 up to 115 kg/h for SO 2 Connections PVC tube 32/40 PVC tube 40/50, extensions PVC tube 20/25, reductions Mains voltage control panel 115 V or 230 V (50/60 Hz) Fastening material for wall mounting Labelling of the control panel German, English, French or Spanish Servomotor protection: IP 65 actuating time 0-100%: 4 seconds adm. ambient temperature: 0 to +40 C adm. storage temperature: -10 to +50 C weight: 2 kg Control panel protection: IP 54 weight: 8,5 kg 110 475 475 110 Technical data Nominal pressure Testing pressure 1170 Vacuum change-over device U 185-2 16 bar 23 bar 340 396 Connection inlet groove flange DN 25 (G1 )/PN 16, to DIN 2527/2512 Connection outlet tongue flange DN 25 (G1 )/PN 16, to DIN 2527/2512 Material valve body and flanges: steel valve balls: stainless steel gaskets: PTFE, glass-fiber reinforced lines: seamless drawn steel tube to DIN 2448 Protection IP 65 Actuating time 0-100% Outputs Power consumption Weight Admiss. ambient temperature 11 sec. at 50 Hz 9 sec. at 60 Hz 3 potential-free outputs; max. charge: 250 V AC, 10 A / 250 V DC, 1 A 0,1 kw 185-1: approx. 20 kg 185-2: approx. 30 kg 0 to + 40 C (Cl 2 + NH 2 ) + 10 to + 40 C (SO 2 ) Measurements in mm 11 GRUNDFOS ALLDOS DISINFECTION
Chlorine header line 542 Lacquered steel header line acc. to DIN 2441, flexible copper lines and connection valves Connection threads 1 (standard cylinder ) G 3/4 G 5/8 1,03-14 M 26x3 1 ¼ (standard drums ) for closed yoke (USA, 1,03-14) for open yoke (France, M 26x3) 15/16-8RH For cylinders 1 C B 350 350 Pressure reducing valve 544 Technical data Nomin. pressure Backpressure Max. flow/ Medium Nominal diameter 16 bar adjustable at 2-3 bar (Cl 2 ); at 3-4 bar (NH 3 ) No. of cylinders Connections Servomotor Order No. 40 kg/h Cl 2 DN 15 G ½ - 544-101 20 kg/h NH 3 DN 15 G ½ - 544-1017 200 kg/h Cl 2 DN 25 G 1-544-102 100 kg/h NH 3 DN 25 G 1-544-1027 40 kg/h Cl 2 DN 15 G ½ x 544-210 20 kg/h NH 3 DN 15 G ½ x 544-2107 200 kg/h Cl 2 DN 25 G 1 x 544-220 100 kg/h NH 3 DN 25 G 1 x 544-2207 H Header line 542 for cylinders Part No. 111 without liquid 111 with liquid trap trap 2 542-622 542-632 3 542-623 542-633 4 542-624 542-634 5 542-625 542-635 6 542-626 542-636 ~35 D L 1 T 1 T 2 L 2 For drums L G 1": L=160 ½ G ": L=130 3000 2000 500 1000 1000 500 500 1000 500 H 162 Pressure reducing valves 544 Accessories for pressure reducing valves No. of drums Header line 542 for drums Collector pipe G ½ Collector pipe G 1 Cl 2 NH 3 + SO 2 Cl 2 1 542-1 542-701 - 2 542-2 542-702 542-32 3 542-3 542-703 542-33 4 542-4 542-704 542-34 5 542-5 542-705 542-35 6 542-6 542-706 542-36 7 542-7 542-707 542-37 8 542-8 542-708 542-38 Description Order No. Manometer 0 to 16 bar, G ¼ (for Cl 2 ) 541-010 Manometer 0 to 16 bar, G ¼ (for NH 3 ) 541-0107 Wall mounting bracket, steel 539-011 Connection set for copper pipe 6/8 (G ½ Cl 2 ) 529-11 Connection set for st. steel pipe 6/8 (G ½ NH 3 ) 529-1017 Pair of threaded flanges (connection flange), groove and tongue, DN 15 Pair of threaded flanges (counterflange), groove and tongue, DN 15 Pair of threaded flanges (connection flange), groove and tongue, DN 25 Pair of threaded flanges (counterflange), groove and tongue, DN 25 529-112 529-12 529-113 529-14 Measurements in mm
Injection units 522-242/-252 Injectors for C 111/C 113 Material / Shut-off valve PVC / ball valve steel / diaphragm valve Connection chlorine solution line Installation connection Order No. PVC pipe 20/25 G 1 522-232 PVC pipe 25/32 G 1 ¼ 522-242 PVC pip 32/40 G 2 522-252 flange DN 25 G 1 ½ 522-302 flange DN 32 G 1 ½ 522-312 flange DN 50 flange DN 80 522-264 flange DN 65 flange DN 100 522-274 flange DN 80 flange DN 125 522-254 flange DN 100 flange DN 150 522-294 flange DN 125 flange DN 200 522-284 With non-return diaphragm FEP diaphragm PTFE piston PFFE coated spring Water connections for PVC pipe 20/25 Vacuum connection for PE hose 8/11 Technical data / Order data Max. capacity (g/h) Water flow (l/h) Adm. press. (bar) Backpress. (bar) Order No. Cl 2 500 300-700 2-16 0-7 545-0500-1 1000 550-1350 2-16 0-7 545-1000-1 2000 850-2220 2-16 0-7 545-2000-1 4000 1200-3300 2-16 0-7 545-4000-1 R D d D l L Injection unit 522-242/-252 Injector 3/4 545-1000-2 / 545-2000-2 / 545-4000-2 Injector 1 545-1000-3 / 545-2000-3 / 545-4000-3 A Chlorine gas absorption cylinder 524-311 PVC, connection for PE tube 8/11, 5l content, filled with 4 kg absorbent, absorption capacity 450 g Cl 2, including fixing accessories The refilling granulate has the order no. 353-225. Measurements in mm 13 GRUNDFOS ALLDOS DISINFECTION
Injectors for C 117/GS 146 Variant: different vacuum connection Connection for PE hose 10/14 Connection for PE hose 12/16 Connection for PVC pipe 12/16 Connection for PVC pipe 15/20 A d D 237 275 DN 20 Injector 1 ¼ 545-3030 / 545-4030 Technical data / Order data Max. capacity (g/h) Water quantity (l/h) Adm. pressure (bar) Backpressure (bar) Part Number Measurements d D A Water connections ¾ hose / ¾ NPT, vacuum connection 8/11 500 550-1350 2-16 0-7 545-1000-2 1000 850-2200 2-16 0-7 545-2000-2 ¾ hose ¾ NPT 400 Water connections 1 hose / 1 NPT, vacuum connection 8/11 500 550-1350 2-16 0-7 545-1000-3 1000 850-2200 2-16 0-7 545-2000-3 1 hose 1 NPT 430 2000 1350-3300 2,5-16 0-7 545-4000-3 Water connections 1 ¼ hose / 1 ¼ NPT, vacuum connection 8/11 3000 2500-4300 4-15 0,5-6,5 545-3030 4000 3400-4700 4-8 0,5-3 545-4030 4000 3600-4300 9-15 3-6,5 545-3030 6000 4600-6000 9-15 3-6,5 545-4030 6000 3400-4500 4-8 0,5-3 545-6030 1 ¼ hose 1 ¼ NPT 400 8000 4700-6000 9-15 3-6,5 545-6030 8000 4200-5800 4-8 0,5-3 545-8030 10.000 6000-8000 9-15 3-6,5 545-8030 10.000 5200-7200 4-8 0,5-3 545-10030 Injectors for GS Systems Technical data / Order data for Cl 2 max. operating pressure: 6 bar injectors for NH 3 and SO 2 on request Dosing capacity Cl 2 Counter pressure bar Length L (mm) Height H (mm) Connection motive water D1 Vacuum connection D2 Connection chlorine solution D1 Order No. 10 kg/h 0,5-3 400 155 PVC pipe 25/32 PE hose 10/14 PVC pipe 25/32 545-0518 10 kg/h 0,5-3 400 155 hose NPT 1 ¼ PE hose ½ hose NPT 1 ¼ 545-1519 10 kg/h 3-7 400 155 PVC pipe 25/32 PE hose 10/14 PVC pipe 25/32 545-3518 10 kg/h 3-7 400 155 hose NPT 1 ¼ PE hose ½ hose NPT 1 ¼ 545-4519 20 kg/h 0,5-3 480 190 PVC pipe 32/40 PVC pipe 20/25 PVC pipe 32/40 545-0615 20 kg/h 3-7 480 190 PVC pipe 32/40 PVC pipe 20/25 PVC pipe 32/40 545-3615 40 kg/h 0,5-3 710 310 PVC pipe 50/63 PVC pipe 20/25 PVC pipe 50/63 545-0715 40 kg/h 3-7 710 310 PVC pipe 50/63 PVC pipe 20/25 PVC pipe 50/63 545-3715 70 kg/h 0,5-3 650 325 PVC pipe 65/75 PVC pipe 40/50 PVC pipe 65/75 545-2816 70 kg/h 3-7 650 325 PVC pipe 65/75 PVC pipe 40/50 PVC pipe 65/75 545-5816 120 kg/h 0,5-3 720 325 PVC pipe 80/90 PVC pipe 40/50 PVC pipe 80/90 545-2916 120 kg/h 3-7 720 325 PVC pipe 80/90 PVC pipe 40/50 PVC pipe 80/90 545-5916 200 kg/h 0,5-3 825 370 PVC pipe 90/110 PVC pipe 40/50 PVC pipe 90/110 545-2016 200 kg/h 3-7 825 370 PVC pipe 90/110 PVC pipe 40/50 PVC pipe 90/110 545-5016
Combined liquid chlorine trap and chlorine gas filter LiquFilt 524 steel vessel filled with chlorineproof rock-wool heater strip Separates the liquid chlorine parts from the chlorine gas flow and cleans the gas from impurities 490 ~ 130 290 190 Drum support Order data Drum support set of two units for storate of one drum material: drum size: load: weight: accessories: Chlorine cylinder balance mounting plate: steel, laquered rollers, axles: steel, nickel-plated min. 0.7 m, max. 1.06 m max. 2000 kg 2 x 23 kg fastening screws, heavy-load dowels Type No. 1 cylinder Type No. 505-632 Type No. 2 cylinders without empty indication 505-624 505-625 with Reed contact for empty indication 505-624-2 505-625-2 without output signal 4-20 ma 505-624-4 505-625-4 Ø 96 Technical data Max. flow Nominal pressure Test pressure Material Input 200 kg/h Cl 2 (gaseous) 16 bar 23 bar high-grade seamless steel, Rockwool gasket material asbestos-free groove flange DN 25 (G 1 ), DIN 2527/2512 min. 110 10 108 M16 Ø 24 400 600 Output tongue flange DN 25 (G 1 ), DIN 2527/2512 110 Weight 22 kg 650 Order data Description Type No. LiquFilt trap and filter, heater strip 115 V (50/60 Hz) 524-205 Drum support 505-632 Neutralisation Plant 15 GRUNDFOS ALLDOS DISINFECTION
Being responsible is our foundation Thinking ahead makes it possible Innovation is the essence Being responsible is our foundation. We know that we have a responsibilty towards the people who are Grundfos, towards the innovation soul of Grundfos as well as towards the surrounding world. Whatever we do, we make sure that we have a firm and sustainable basis for doing it. Thinking ahead makes the innovations possible. We encourage a certain Grundfos way of thinking which is founded upon the belief that everyone must contribute by using his or her judgement and foresight. We are looking for commitment and ideas in everything we do in order to make the best solutions. We think - and we act. Innovation is the essence. It is the innovations that make Grundfos unique. We stand out because of our ability to constantly create new solutions to the ever-changing demands of the pump business. We meet every challenge and we are never afraid of taking the initiative - remainin gtrue to our ideals calls for renewal. Innovation is the soul of Grundfos. www.grundfos.com