Operator: Save these instructions for future use!

1F85-277 ing & Air Conditioning 7 Day/5-1-1 Programmable/Non-programmable, Auto Changeover, Multi-Stage/ Pump Thermostat INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE. PREPARATIONS YOUR THERMOSTAT REPLACES Assemble tools required as shown below. Description 1F85-277 Pump (No Aux. or Emergency ) Pump (with Aux. or Emergency ) Standard & Cooling Systems Two Stage & Two Stage Cool Standard Only Systems Millivolt Only Systems Floor or Wall Furnaces Standard Central Air Conditioning Gas or Oil Electric Furnace Hydronic (Hot Water) Zone 2 Wires Hydronic (Hot Water) Zone 3 Wires! CAUTION No To prevent electrical shock and/or equipment damage, disconnect electric power to system at main fuse or circuit breaker box until installation is complete. HAND OR POWER DRILL WITH 3/16 INCH DRILL BIT, IF NEEDED FLAT BLADE SCREWDRIVER WIRE CUTTER/STRIPPER REMOVING OLD THERMOSTAT Before removing wires from old thermostat's switching subbase, label each wire with the terminal designation it was removed from. 1. Shut off electricity at the main fuse box until installation is complete. Ensure that electrical power is disconnected. 2. Remove Old Thermostat: A standard heat/cool thermostat consists of three basic parts: a. The cover, which may be either a snap-on or hinge type. b. The base, which is removed by loosening all captive screws. c. The switching subbase, which is removed by unscrewing the mounting screws that hold it on the wall or adaptor plate. 3. Remove the front cover of the old thermostat. With wires still attached, remove wall plate from the wall. If the old thermostat has a wall mounting plate, remove the thermostat and the wall mounting plate as an assembly. 4. Identify each wire attached to the old thermostat. 5. Disconnect the wires from the old thermostat one at a time. DO NOT LET WIRES FALL BACK INTO THE WALL. 6. Install new thermostat using the following procedures. Mounting Hole O B L W2 G Figure 1 Thermostat base Mounting Hole Elec-Gas Switch ATTENTION! This product does not contain mercury. However, this product may replace a unit which contains mercury. Do not open mercury cells. If a cell becomes damaged, do not touch any spilled mercury. Wearing non-absorbent gloves, clean up the spilled mercury and place into a container which can be sealed. If a cell becomes damaged, the unit should be discarded. Mercury must not be discarded in household trash. When the unit this product is replacing is to be discarded, place in a suitable container and return to White-Rodgers at 2895 Harrison Street, Batesville, AR 72501 for proper disposal. ELEC. ON AUTO Y2 C R Y1 GAS White-Rodgers is a division of Emerson Electric Co. www.white-rodgers.com PART NO. 37-6560B Replaces 37-6560A 0737

MOUNTING AND WIRING! WARNING Do not use on circuits exceeding specified voltage. Higher voltage will damage control and could cause shock or fire hazard. Do not short out terminals on gas valve or primary control to test. Short or incorrect wiring will damage thermostat and could cause personal injury and/or property damage. Thermostat installation and all components of the system shall conform to Class II circuits per the NEC code. Electric/Gas Switch (Fan Option) This thermostat is configured from the factory to operate a heat/ cool, fossil fuel (gas, oil, etc.), forced air system. It is configured correctly for any system that DOES NOT require the thermostat to energize the fan on a call for heat. If you system is an electric heat or heat-pump system that REQUIRES the thermostat to turn on the fan on a call for heat, locate the ELEC/GAS switch on the back of the thermostat (see fig. 1) and switch it to the ELEC position. This will allow the thermostat to energize the fan immediately on a call for heat. If you are unsure if the heating/ cooling system requires the thermostat to control the fan, contact a qualified heating and air conditioning service person. When the thermostat is configured for Pump, the thermostat will always power the circulator fan on a call for heat in the HEAT mode. The ELEC/GAS switch must be set to match the type of Auxiliary heat your system uses for proper operation in the EMERgency mode. All wiring diagrams are for typical systems only. Refer to equipment manufacturers instructions for specific system wiring information. O Reversing Valve Energized in Cool Mode B Reversing Valve Energized in, Off, Emergency Mode Y2 2nd Stage Y1 Contactor! CAUTION Take care when securing and routing wires so they do not short to adjacent terminals or rear of thermostat. Personal injury and/or property damage may occur. Attach Thermostat Base to Wall 1. Remove the packing material from the thermostat. Gently pull the cover straight off the base. Forcing or prying on the thermostat will cause damage to the unit. 2. Connect wires beneath terminal screws on base using appropriate wiring schematic (see figs. 2 through 4). 3. Place base over hole in wall and mark mounting hole locations on wall using base as a template. 4. Move base out of the way. Drill mounting holes. 5. Fasten base loosely to wall, as shown in fig. 1, using two mounting screws. Place a level against bottom of base, adjust until level, and then tighten screws. (Leveling is for appearance only and will not affect thermostat operation.) If you are using existing mounting holes, or if holes drilled are too large and do not allow you to tighten base snugly, use plastic screw anchors to secure subbase. 6. Push excess wire into wall and plug hole with a fireresistant material (such as fiberglass insulation) to prevent drafts from affecting thermostat operation. Battery Location 2 AA alkaline batteries are included in the thermostat at the factory with a battery tag to prevent power drainage. You must remove the battery tag to engage the batteries. If BATT is displayed, the batteries are low and should be replaced. For best results, replace all batteries with new premium brand alkaline batteries such as Duracell or Energizer. To replace batteries, press system button to OFF, install the batteries along the top of the base (see Fig. 1). The batteries must be installed with the positive (+) end to the left. Figure 2. Typical wiring diagram for single transformer heat pump systems *The 24 volt neutral connection to terminal C on the thermostat is not required if you replace the batteries once a year with fresh AA Energizer alkaline batteries. G Fan W2 Aux NOTE If safety circuits are in only one of the systems, remove the transformer of the system with NO safety circuits. Emergency C * MONITOR SWITCH L R THERMOSTAT Hot 24 VAC 120 VAC Neutral TRANSFORMER (Class II Current Limited) CUT AND TAPE OFF! HOT 120 VAC 24 VAC NEUTRAL O B Y2 Y1 G W2 C * Reversing Valve Energized in Cool Mode Reversing Valve Energized in, Off, Emergency Mode 2nd Stage Contactor Fan MONITOR SWITCH Figure 3. Typical wiring diagram for two transformer heat pump systems with NO safety circuits *The 24 volt neutral connection to terminal C on the thermostat is not required if you replace the batteries once a year with fresh AA Energizer alkaline batteries. Aux Emergency TWO COMMONS MUST BE JUMPERED TOGETHER! L R Limit or Safety Switches THERMOSTAT Hot 24 VAC 120 VAC Neutral TRANSFORMER (Class II Current Limited)

WIRING DIAGRAMS NOTE Polarity must be observed. If the HOT side of the second transformer is jumpered to the COMMON side of the first transformer a short will be made. Damage to equipment will occur when power is restored. O B * Y2 Y1 G W2 C Reversing Valve Energized in Cool Mode Reversing Valve Energized in, Off, Emergency Mode 2nd Stage Contactor Fan Aux Emergency MONITOR SWITCH L R Limit or Safety Switches 24 VAC ACCESSORY RELAY N.O. CONTACT COMMON THERMOSTAT 24 VAC Auxiliary ing Transformer (Class II Current Limited) 120 VAC Limit or Safety Switches HOT NEUTRAL NOTE The accessory relay scheme is required when safety circuits exist in both systems. TWO COMMONS MUST BE JUMPERED TOGETHER! COMMON Limit or Safety Switches Limit or Safety Switches HOT 24 VAC 120 VAC Pump Transformer (Class II Current Limited) Figure 4. Typical wiring diagram for two transformer heat pump systems with safety circuits in BOTH systems *The 24 volt neutral connection to terminal C on the thermostat is not required if you replace the batteries once a year with fresh AA Energizer alkaline batteries. NEUTRAL Refer to equipment manufacturers' instructions for specific system wiring information. You can configure the thermostat for use with the following heat pump system types: HEAT PUMP TYPE 1. Single stage compressor system; gas or electric backup. This thermostat is designed to operate a single-transformer system. If you have a two-transformer system, cut and tape off Pump Terminal Outputs one transformer. If transformer safety circuits are in only one of the systems, remove the transformer of the system with NO safety circuits. If required, replace remaining transformer with a 75VA Class II transformer. After disconnecting one transformer, the two commons must be jumpered together. Use the terminal output information below to help you wire the thermostat properly for your heat pump system. After wiring, see CONFIGURATION section for proper thermostat configuration. THERMOSTAT TERMINALS (HEAT PUMP) L C* R W2 Y2 Y1 G O B Malfunction 24 Volt 24 Volt HP 1 and Emergency No and Blower/Fan Energized Energized Energized Pump 1 Light (Common) (Hot) Emergency Mode Output Cool mode on call for in Cool in 2nd stage 1st stage 1st stage and Cool Mode OFF HP 2 2nd (compressor) Set GAS/ELEC switch Emergency Pump 2 3rd stage stage for Emergency mode mode compressor *The 24 volt neutral connection to terminal C on the thermostat is not required if you replace the batteries once a year with fresh AA Energizer alkaline batteries. O B Y1 Y2 G W2 C * R THERMOSTAT Reversing Valve Energized in Cool Mode Reversing Valve Energized in Mode Off Emergency Contactor Stage 2 Contactor Stage 1 Fan Stage 1 Stage 2 Hot 24 VAC 120 VAC Neutral TRANSFORMER (Class II, Current Limited) Figure 5. Typical wiring diagram for single transformer multi-stage systems *The 24 volt neutral connection to terminal C on the thermostat is not required if you replace the batteries once a year with fresh AA Energizer alkaline batteries.

Refer to equipment manufacturers' instructions for specific system wiring information. You can configure the thermostat for use with either multi-stage electric heat systems or multi-stage gas systems. When configured for electric heat, the G terminal (blower/fan) will be energized on a call for heat. This thermostat is designed to operate a single-transformer system. If you have a two-transformer system, cut and tape off Multi-Stage Terminal Outputs one transformer. If transformer safety circuits are in only one of the systems, remove the transformer of the system with NO safety circuits. If required, replace remaining transformer with a 75VA Class II transformer. After disconnecting one transformer, the two commons must be jumpered together. Use the terminal output information below to help you wire the thermostat properly for your multi-stage system. After wiring, see CONFIGURATION section for proper thermostat configuration. THERMOSTAT TERMINALS (MULTI-STAGE) L C* R W2 Y2 Y1 G O B Multi-stage Malfunction 24 Volt 24 Volt Mode mode Cool Mode Cool Mode Blower/Fan Energized Energized Energized Light (Common) (Hot) 2nd stage 1st stage 2nd stage 1st stage on call for Cool (and in Cool in, Off, if configured Mode Emergency to Electric ) Modes *The 24 volt neutral connection to terminal C on the thermostat is not required if you replace the batteries once a year with fresh AA Energizer alkaline batteries. CHECK THERMOSTAT OPERATION NOTE To prevent static discharge problems, touch side of thermostat to release static build-up before touching any keys. If at any time during testing your system does not operate properly, contact a qualified serviceperson.! Fan Operation If your system does not have a G terminal connection, skip to ing System. 1. Turn on power to system. 2. Move FAN switch to ON position. The blower should begin to operate. 3. Move FAN switch to AUTO position. The blower should stop immediately. CAUTION Do not allow the compressor to run unless the com- pressor oil heaters have been operational for 6 hours and the system has not been operational for at least 5 minutes. ing System 1. Press button to select the Flame icon ( ). If the auxiliary heating system has a standing pilot, be sure to light it. 2. Press to adjust thermostat setting to 1 above room temperature. The heating system should begin to operate. The display should show STG1. However, if the setpoint temperature display is flashing, the compressor lockout feature is operating (see Configuration menu, item 5). 3. Adjust temperature setting to 3 above room temperature. If your system configuration is set at MS2, HP2 or HP1, the auxiliary heat system should begin to operate and the display should show STG1+2. 4. Press to adjust the thermostat below room temperature. The heating system should stop operating. Emergency System EMER bypasses the Pump to use the heat source wired to terminal E on the thermostat. EMER is typically used when compressor operation is not desired, or you prefer back-up heat only. 1. Press button to select EMER. EMER will flash on the display. 2. Press to adjust thermostat setting above room temperature. The Aux. heating system will begin to operate. The display will show STG1 flashing EMER and Flame icon ( ) to indicate that the Aux. system is operating. 3. Adjust temperature setting to 3 above room temperature. The auxiliary heat system should begin to operate and the display should show STG1+2. 4. Press to adjust the thermostat below room temperature. The Aux. heating system should stop operating.! CAUTION To prevent compressor and/or property damage, if the outdoor temperature is below 50 F, DO NOT operate the cooling system. Cooling System 1. Press button to select the Snowflake icon ( ). 2. Press to adjust thermostat setting below room temperature. The blower should come on immediately on high speed, followed by cold air circulation. The display should show STG1. 3. Adjust temperature setting to 3 below room temperature. The second stage cooling should begin to operate and the display should show STG1+2. 4. Press to adjust the temperature setting above room temperature. The cooling system should stop operating. 4

Before you begin programming your thermostat, you should be familiar with its features and with the display and the location and operation of the thermostat buttons. Your thermostat consists of two parts: the thermostat cover and the base. To remove the cover, pull it straight out from the base. To replace the cover, line up the cover with the base and press until the cover snaps onto the base. The Thermostat Buttons and Switches OPERATION 1 Raises temperature setting 2 Lowers temperature setting. 3 TIME button. 4 PRGM (program) button. 5 RUN (run program) button. 6 HOLD temperature button. 7 FAN switch (ON, AUTO) 8 button (COOL, AUTO, HEAT, EMER, OFF) The Display 9 Indicates day of the week. 10 Flame icon ( ) is displayed when the system is in HEAT mode. Snowflake icon ( ) is displayed when the system is in COOL mode. Flame icon ( ) and Snowflake icon ( ) are displayed simultaneously when thermostat is in AUTO mode. 11 Displays BATT when the 2 "AA" batteries are low and should be replaced. Only BATT and LO in the minutes field are displayed when batteries are low and with no system power. 12 Alternately displays current time and temperature. Displays LO in the minutes field when batteries are low. 13 The word HOLD is displayed when the thermostat is in the HOLD mode. HOLD is displayed flashing when the thermostat is in a temporary HOLD mode. 14 Displays currently programmed set temperature (this is blank when is OFF). 15 Displays FLTR when the system has run for the programmed filter time period as a reminder to change or clean your filter. The configuration menu allows you to set certain thermostat operating characteristics to your system or personal requirements. Set button to OFF, then simultaneously press and to enter configuration menu. The display will show the first item in the configuration menu. The configuration menu table summarizes the configuration options. An explanation of each option follows. Press to change to the next menu item. To exit the menu and return to the program operation, press RUN. If no keys are pressed within fifteen minutes, the thermostat will revert to normal operation. Figure 6 Thermostat display, buttons and switches 16 Display ( ) when in keypad lockout mode. 17 EMER is displayed flashing when the system is in EMER mode. 18 The word FAULT will be displayed when there is a malfunction in the HEAT/COOL system. 19 Display ( ) when limited HEAT/COOL range is activated. The icon will flash if an attempt is made to adjust the temperature beyond the limited HEAT/COOL temperature range. 20 Stage1 & 2 indicators: The thermostat shall indicate when the first and second stage is energized except in emergency mode. The icon is STG 1 for the first stage energized. The icons for the first and second stage energized are STG1+2 located in the upper right side of the display. CONFIGURATION MENU 1) Single Stage, Multi-stage or Pump System Configuration This control can be configured for Pump or two stage heat/two stage cool multi-stage operation. The display indicates MS 2 (default for multi-stage mode) in the display. The Multi-stage configuration can be toggled to SS1, HP2, or HP1 by pressing the or key. In Multi-stage configuration, button will not have EMERgency mode. 2) Programs Per Week This control can be configured for 7 independent day or 5/1/1/ programming or non-program mable mode. The display indicates 7d as default. The programs per week can be toggled to 5d or 0d by pressing the or keys. With 0d selected for non- 5

CONFIGURATION MENU Press the button until OFF is displayed, then press the and simultaneously INSTALLER/CONFIGURATION MENU Press Displayed Press or Step Button(s) (Factory Default) to select Comments 1 System MS 2 SS1, HP2, HP1 Selects Single stage, Multi-stage, or Pump (Single stage or 2-stage) System Configuration 2 System 7d 5d, 0d Selects Programs Per Week 3 System PRG 4 PRG 2 Selects Programmable Periods (PRG 2 = 2 programmable periods; PRG 4 = 4 programmable periods) 4 System 4:00 HOLD 0:15 to 4:00 Selects Temporary Program Override Time (increments of 15 minutes) 5 System EMR OFF Selects Energy Management Recovery OFF or ON (ON) 6 System FA SL Selects Fast or Slow Cycle Selection 7 System CL CL Selects Lockout CL OFF or ON (OFF) (ON) 8 System CDL CDL Selects Backlight Display (ON) (OFF) 9 System FA FA Selects Fast Second Stage ON or OFF (ON) (OFF) 10 System 0 FLTR 50-1950 (increments of 50) Selects filter replacement run time 11 System 0 F 4 LO to 4 HI Selects Temperature Display Adjustment 4 LO to 4 HI (Room Temperature) 12 System F C Selects temperature display F or C selection 13 System AU On OFF Selects AUTO Mode ON or OFF 14 System LR LR 62 to LR89 Selects Limited HEAT range (90) 15 System LR LR 46 to LR 82 Selects Limited COOL range (45) 16 System CA CA Feature Not Available (OFF) (ON) 17 System (ON) Selects Keypad Lockout (OFF) 18 System 0 001 to 999 Selects Keypad lockout combination number Press System to set code 19 Run Returns to the OFF position programmable, button selection will skip Programmable periods (item 3), programmable hold time (item 4) and EMR (item 5). 3) Programmable Periods This control can be configured for 4 or 2 programmable periods. The display indicates PRG 4 in the display as default. The programmable periods can be toggled to PRG 2 by pressing the or keys. 4) Select Temporary Program Override Time The thermostat can hold any temperature you set it to for the amount of time you select on this option. Your choices are 0:15 to 4:00 hours in 15 minute increments. 6 Example: a. You have selected 3:00 hours for the Temporary Program Override time period. b. With the thermostat set to or Cool, press or to set the temperature to your preference. The thermostat will maintain this temperature setting for 3 hours with HOLD blinking to remind you it is in Temporary Hold. After 3 hours, the thermostat will go back to the program temperature and HOLD will no longer blink or display.

5) Select Energy Management Recovery OFF or ON Energy Management Recovery (EMR) causes the thermostat to start heating or cooling early to make the building temperature reach the program setpoint at the time you specify. ing will start 5 minutes early for every 1 of temperature required to reach setpoint. Cooling allows more time per degree because it takes longer to reach temperature. Example: You select EMR and have your heating programmed to 65 at night and 70 at 7 AM. If the building temperature is 65 the difference between 65 and 70 is 5. Allowing 5 minutes per degree the thermostat setpoint will change to 70 at 6:35 AM. 6) Fast or Slow Cycle Selection The factory default setting is fast cycle, which cycles 1st stage at approximately 1.2 F and 2nd stage 0.75 F. If you prefer slow cycle, press the or key to change to SL. The 1st stage and 2nd stage would be 1.5 F and 1.2 F respectively. 7) Select Lockout CL OFF or ON Selecting CL ON will cause the thermostat to wait 5 minutes before turning on the compressor if the heating and cooling system loses power. It will also wait 5 minutes minimum between cooling and heating cycles. This is intended to help protect the compressor from short cycling. Some newer compressors already have a time delay built in and do not require this feature. Your compressor manufacturer can tell you if the lockout feature is already present in their system. When the thermostat compressor time delay occurs it will flash the setpoint for about five minutes. 8) Select Backlight Display The display backlight improves display contrast in low lighting conditions. When the C terminal is powered, selecting backlight CdL ON will turn the light on continuously. Select backlight OFF will keep the light on momentarily after any key is pressed. When the C terminal is not powered, this selection has no effect. 9) Select (Fast) Second Stage ON or OFF In the run mode, if the setpoint temperature is manually raised by 3 F (2 C) or more above the actual temperature with the, and the fast second stage feature is enabled, FA ON, the second stage will energize immediately. With FA OFF, second stage will not energize until the setpoint temperature is 1 F or more above actual temperature for more than ten minutes. 10)Select filter replacement run time The thermostat will display FLTR after a set time of operation. This is a reminder to change or clean your air filter. This time can be set from 0 to 1950 hours in 50 hour increments. A selection of 000 will cancel this feature. When FLTR is displayed, you can clear it by pressing HOLD and RUN at the same time. This resets the timer and starts counting the hours until the next filter change. Contact your system manufacturer for a specific replacement/maintenance interval. 11)Select Temperature Display Adjustment 4 LO to 4 HI Allows you to adjust the room temperature display up to 4 higher or lower. Your thermostat was accurately calibrated at the factory but you have the option to change the display temperature to match your previous thermostat. The current or adjusted room temperature will be displayed on the left side of the display. CONFIGURATION MENU 12)Select F or C Readout Changes the display readout to Centigrade or Fahrenheit as required. 13)Selected Auto mode This control will feature AUTO changeover mode when AU on is selected (default). Press the or keys in the menu mode to defeat the auto changeover mode (OFF). 14)Limited Range This feature provides a maximum setpoint temperature for heat. The default setting is 90 F. It can be changed between 62 F and 89 F by pressing the or key. 15)Limited Cool Range This feature provides a minimum setpoint temperature for cool. The default setting is 45 F. It can be changed between 46 F and 82 F by pressing the or key. 16) Defeat on Comfort Alert error By selecting CAL on (default), the compressor will be locked when any CA error is detected. The compressor will not be locked when CA error is detected if CAL is OFF. 17 & 18) Keypad Lockout This menu selection will display lock icon ( ) and OFF (default, keypad not locked out). The and are used to toggle the selection between OFF and ON (keypad locked out). When the keypad lockout selection is enabled (ON), and the button is pressed again, the display will indicate the number 0 (default, still disabled) in the time digits. The and are used to set the combination number from 0 to 999. If a combination of 0 is selected and the button is pressed, the menu will be exited and keypad will not be locked. If 1 to 999 is selected and the button is pressed, the combination is stored into memory and the menu is exited. The ( ) will display designating keypad locked with a valid combination. The button will operate for 10 seconds after the menu mode is exited to allow the user to change the mode from OFF to the desired mode. While the keypad is locked out, a simultaneous press of and will enter the configuration menu from any mode instead of only OFF mode. When the menu is entered with the keypad lockout feature enabled, the first menu item displayed is the combination code 0. The or keys are used to set the combination unlock number from 0 to 999. If the unlock number matches exactly with the combination lock number stored in memory when the button is pressed, the keypad is unlocked and the ( ) is removed. If the unlock number does not match when the button is pressed, the menu is exited and the keypad remains disabled. To reset the combination code and unlock the keypad if the code is forgotten, see troubleshooting section. 7

SPECIFICATIONS ELECTRICAL DATA Electrical Rating: 20 to 30 VAC 50/60 Hz or DC 0.05 to 1.5 Amps (Load per terminal) 2.5 Amps Maximum Total Load (All terminals combined) OPERATION The system "mode" is selected by pressing the button. Icons on the bottom right corner of the display will indicate the mode: COOL ( ), AUTO ( ), HEAT ( ), EMER, or OFF. In any mode except OFF, the setpoint temperature will be shown on the right side of the display. In OFF, this area will be blank. The current temperature will be displayed on the left side of the display. To operate properly in the AUTO mode, the heat setpoint temperature cannot be the same as or higher than the cool setpoint temperature. The heat setpoint must be at least 1 lower than the cool setpoint. Automatic System Changeover When the thermostat is in the AUTO mode, both the Flame and Snowflake icons are displayed. The thermostat will call for heat or cool depending on the room temperature. The setpoint temperature displayed will be that of the last mode called. If the last system cycle was heat, the HEAT setpoint will be displayed. If the room temperature raises above the HEAT setpoint and the COOL setpoint and a call for cool is required, the temperature displayed will change to be the COOL setpoint. Second Stage Time Delay Your thermostat is designed to determine the optimum time to activate the second stage. Simply raising the temperature in heating or lowering it in cooling will not always force the thermostat to bring the second stage on quickly. There is a time delay from 0-30 minutes depending on the performance of the first stage of the system. EXAMPLE: For the last 2 hours the thermostat is set on 70 and the room temperature is 70 with the equipment using only the first stage of heat. Since the equipment is keeping the temperature within 1 of setpoint, the thermostat will delay second stage for a longer time if you manually raise the temperature or if the room temperature quickly changes. Once the second stage comes on, it will come on sooner the next time there is a difference between the setpoint and the room temperature. The net effect of the staging program is that when the first stage is capable of making temperature the second stage will delay longer. When the thermostat calculates that first stage cannot make temperature in a reasonable time, the second stage will come on sooner. This built in function automatically optimizes the use of additional stages of heat or cool. THERMAL DATA Setpoint Temperature Range: 45 F to 90 F (7 C to 32 C) Operating Ambient Temperature Range: 32 F to 105 F Operating Humidity Range: 0 to 90% RH (non-condensing) Shipping Temperature Range: -40 F to 150 F Manual Operation Permanent Program Override (HOLD HOLD) With the button set to HEAT or COOL, press the HOLD button once and release. HOLD will be displayed. Use or to adjust the temperature. The thermostat will hold the room temperature at the selected setting until you press RUN button to start program operation again. Temperature Program Override Press or until the display shows the temperature you want. The thermostat will override current programming and keep the room temperature at the selected temperature for a programmed time period. HOLD will be displayed and flashing. The thermostat will automatically revert to the program after programmed period. LOW BATTERY INDICATOR If the 2 AA alkaline batteries are low and should be replaced, the display will be blank except for LO BATT. We recommend replacing batteries every 2 years. If the home is going to be unoccupied for an extended period (over 3 months), the batteries should be replaced before leaving. When the batteries are low, pressing any button will cause the display to operated for ten seconds. After ten seconds, the display will be blank except for LO BATT. You cannot program with low batteries, but you can override setpoint temperature. After LO BATT has been displayed for 4 weeks, the thermostat will raise the temperature 10 degrees above your setpoint in COOL mode and will drop the temperature 10 degrees below your setpoint in HEAT mode. If the LO BATT condition continues, and when it reaches certain value, the thermostat will turn off all the loads and LO BATT will flash. SIMPLIFIED COPY DAY FUNCTION This feature allows Monday s program to be copied into the rest of the week s programming. This feature is available the first time you programmed your thermostat. To use this feature, simply enter the program for Monday as described in ENTERING YOUR PROGRAM, then press RUN or HOLD. The only way to restore this feature is to complete a software reset (see Reset Operation under TROUBLESHOOTING section). COPY DAY FUNCTION This feature allows a selected day s program to be copied to the desired day s programming. To use this feature: in PRGM mode, select the day to be copied from by pressing the HOLD button. Enter the program for the selected day as described in ENTERING YOUR PROGRAM. Press and hold the TIME button for 4 seconds to begin the COPY mode. The LCD will display COPY and the selected day to be copied. The day the program will copy to will be flashing. Press the HOLD button to select the day you want to copy to. Press TIME to complete the Copy Day operation and return to PRGM mode. Press RUN to exit. 8

PROGRAMMING YOUR THERMOSTAT This section will help you plan your thermostat's program to meet your needs. For maximum comfort and efficiency, keep the following guidelines in mind when planning your program. When heating (cooling) your building, program the temperatures to be cooler (warmer) when the building is vacant or during periods of low activity. During early morning hours, the need for cooling is usually minimal. Planning Your Program Look at the factory preprogrammed times and temperatures shown in the sample schedule. If this program will suit your needs, simply press the RUN button to begin running the factory preset program. If you want to change the preprogrammed times and temperatures, follow these steps. Determine the time periods and temperatures for your program. You can program four or two periods for each day (see Configuration menu, item 3). You may use the same heating and cooling temperatures for consecutive time periods. You can choose start times, heating temperatures, and cooling temperatures independently (for example, you may select 5:00 AM and 70 as the weekday 1st period heating start time and temperature and also choose 7:00 AM and 76 as the weekday 1st period cooling start time and temperature). Use the table to plan your program time periods and the temperatures you want during each period. Fill in the complete table to have a record of your programs. SAMPLE ing/cooling Schedule Plan (Factory Program) Entering Your Program Set Current Time and Day OPERATION 1. Press TIME button once. The display will show the hour only. EXAMPLE: 2. Press and hold either or until you reach the correct hour and AM/PM designation (AM begins at midnight; PM begins at noon). 3. Press TIME once again. The display window will show the minutes only. EXAMPLE: 4. Press and hold either or until you reach the correct minutes. 5. Press TIME once again. The display will show the day of the week. 6. Press or until you reach the current day of the week. 7. Press RUN once. The display will show the correct time and room temperature alternately. PM Enter ing Program 1. Move the switch to HEAT. 2. Press PRGM once. MO (indicating Monday program) will appear in the display. Also displayed are the currently programmed start time for the 1st heating period and the currently programmed temperature (flashing). COOL HEAT Period 1ST 2ND 3RD 4TH 1ST 2ND 3RD 4TH Start Time 6:00 AM 8:00 AM 5:00 PM 10:00 PM 6:00 AM 8:00 AM 5:00 PM 10:00 PM ALL DAYS OF THE WEEK Temperature 70 F 62 F 70 F 62 F 78 F 85 F 78 F 82 F EXAMPLE: ing/cooling Schedule Plan This display window shows that for Monday s 1st heating period, the start time is 6:00 AM, and 70 is the programmed temperature (this example reflects factory preprogramming). 3. Press or to change the displayed temperature to your selected temperature for Monday s 1st heating program period. 4. Press TIME once (the programmed time will flash). Press or until your selected start time for Monday s 1st heating program period appears. The time will change PERIOD 1 HEAT COOL Time Temp Time Temp PERIOD 2 HEAT COOL Time Temp Time Temp PERIOD 3 HEAT COOL Time Temp Time Temp PERIOD 4 HEAT COOL Time Temp Time Temp Mon Tues Wed Thur Fri Sat Sun 9

OPERATION in 15-minute increments. When your selected time is displayed, press TIME again to return to the change temperature mode. 5. Press PRGM once. The currently programmed start time and setpoint temperature for the Monday s 2nd heating program period will appear. 6. Repeat steps 3 and 4 to select the start time and heating temperature for Monday s 2nd heating program period. 7. Repeat steps 3 through 5 for the 3rd and 4th heating program periods. Monday heating programs are now complete. NOTE If you are programming your thermostat for the first time and you want programming for all days of the week to be the same as Monday s program, press RUN or HOLD at this point, and proceed to Enter Cooling Program. (This simplified COPY DAY feature only works the first time you program your thermostat. If you want to copy one day s programming to a specific day programming, refer to COPY DAY FUNCTION in OPERATING FEATURES. If you are changing your thermostat s programming, you must program each day separately.) 8. Press PRGM once. TU (indicating Tuesday program) will appear in the display, along with the start time for the 1st heating period and the currently programmed temperature. 9. Repeat steps 3 through 7 to complete Tuesday s heating programming. 10.Continue entering each day s programming until all heating periods time and temperatures have been entered. 11.When you have complete entering your heating program, press RUN. TROUBLESHOOTING Enter Cooling Program If the outside temperature is below 50 F, disconnect power to the cooling system before programming. Energizing the air conditioner compressor during cold weather may cause personal injury or property damage. 1. Press button to COOL position. 2. Follow Enter ing Program for entering your cooling program, using your selected cooling times and temperatures. CHECK YOUR PROGRAMMING Follow these steps to check your thermostat programming one final time before beginning thermostat operation. 1. Press button to HEAT position. 2. Press PRGM to view the 1st Monday heating period time and temperature. Each time you press PRGM, the next heating period time and temperature will be displayed in sequence for each weekday, then Saturday and Sunday program periods (you may change any time or temperature during this procedure). 3. Press RUN. 4. Press button to COOL position. 5. Repeat step 2 to check cooling program. 6. Press button to HEAT or COOL and press RUN to begin program operation. NOTE: Batteries are not required to keep your programming or menu data. With two optional "AA" batteries installed, your thermostat will maintain time and continuously display the temperature during a loss of AC power. Installed batteries will also allow programming prior to installation. YOUR THERMOSTAT IS NOW PROGRAMMED AND READY TO PROVIDE MAXIMUM COMFORT AND EFFICIENCY! Reset Operation If a voltage spike or static discharge blanks out the display or causes erratic thermostat operation, you can reset the thermostat by removing the wires from terminals R and C and removing batteries for 2 minutes. After resetting the thermostat, replace the wires and batteries. If the thermostat has been reset and still does not function correctly, contact your heating/cooling service person or place of purchase.! CAUTION Symptom No /No Cool/No Fan (common problems) No 10 Possible Cause 1. Blown fuse or tripped circuit breaker. 2. Furnace power switch to OFF. 3. Furnace blower compartment door or panel loose or not properly installed. 1. Pilot light not lit. 2. button not set to HEAT. 3. Loose connection to thermostat or system. 4. Furnace Lock-Out Condition. may also be intermittent. 5. ing system requires service or thermostat requires replacement. Corrective Action Replace fuse or reset breaker. Turn switch to ON. Replace door panel in proper position to engage safety interlock or door switch. Re-light pilot. Press button to HEAT and raise setpoint above room temperature. Verify thermostat and system wires are securely attached. Many furnaces have safety devices that shut down when a lock-out condition occurs. If the heat works intermittently contact the furnace manufacturer or local service person for assistance. Diagnostic: Press button to HEAT and raise the setpoint above room temperature. Within a few seconds the thermostat should make a soft click

Symptom No (continued) No Cool, Cool or Fan Runs Constantly Furnace (Air Conditioner) Cycles Too Fast or Too Slow (narrow or wide temperature swing) Thermostat Setting & Thermostat Thermometer Disagree Blank Display and/or Keypad Not Responding Setpoint will not Respond to the Temperature Up Key Cool Setpoint will not Respond to the Temperature Down Key Forgot Keypad Lockout Code Possible Cause 5. ing system requires service or thermostat requires replacement. (continued) 1. button not pressed to COOL. 2. Loose connection to thermostat or system. 3. Cooling system requires service or thermostat requires replacement. 1. Possible short in wiring. 2. Possible short in thermostat. 3.Possible short in heat/cool/fan system. 4. FAN Switch set to Fan On. 1. The location of the thermostat and/or the size of the ing System may be influencing the cycle rate. 1. Thermostat thermometer setting requires adjustment. 1. Voltage spike or static discharge. 1. The desired setpoint conflicts with the setpoint of the COOL mode. 1. The desired setpoint conflicts with the setpoint of the HEAT mode. Corrective Action TROUBLESHOOTING sound. This sound usually indicates the thermostat is operating properly. If the thermostat does not click, try the reset operation listed above. If the thermostat does not click after being reset contact your heating and cooling service person or place of purchase for a replacement. If the thermostat clicks, contact the furnace manufacturer or a service person to verify the heating is operating correctly. Press button to COOL and lower setpoint below room temperature. Verify thermostat and system wires are securely attached. Same procedure as diagnostic for No condition except set the thermostat to COOL and lower the setpoint below the room temperature. There may be up to a five minute delay before the thermostat clicks in Cooling. Check each wire connection to verify they are not shorted or touching together. No bare wire should stick out from under terminal screws. Try resetting the thermostat as described above. If the condition persists the manufacturer of your system or service person can instruct you on how to test the / Cool system for correct operation. If the system operates correctly, replace the thermostat. Digital thermostats normally provide precise temperature control and may cycle faster than some older mechanical models. A faster cycle rate means the unit turns on and off more frequently but runs for a shorter time so there is no increase in energy use. If you would like to increase the cycle time, choose SL for slow cycle in the menu, step 4. If an acceptable cycle rate is not achieved as received or by choosing slow cycle, contact a local service person for additional suggestions. The thermometer can be adjusted +/- 4 degrees. See Temperature Display Adjustment in the Configuration Menu section. Use the Reset Operation at top of previous page. Change system mode to COOL. Raise the Cool setpoint. Return to HEAT mode and set desired temperature. Change system mode to HEAT. Lower the setpoint. Return to COOL mode and set desired temperature. CAUTION: This resets the thermostat to factory default settings of the configuration menu. After performing this reset, the thermostat will require configuration again. Be sure that you know the required configuration settings before resetting. With the thermostat in any mode, press and at the same time to enter the configuration menu at the point where the lockout code is to be entered. Press 11

TROUBLESHOOTING Symptom Forgot Keypad Lockout Code ( conti nued) Possible Cause Corrective Action and and button at the same time to reset the lockout code, unlock the keypad and reset all configuration menu settings. Why won t my 2nd or 3rd stage come on? FAQ Symptom My thermostat is reading in Celsius. How do I change it to Fahrenheit? First stage is keeping up with demand. Corrective Action Your thermostat is designed to determine the optimum time to activate the second stage. Simply raising the temperature in heating or lowering it in cooling will not always force the thermostat to bring the second stage on quickly. There is a time delay from 0-30 minutes depending on the performance of the first stage of the system. Your thermostat display can be set to display temperature in Fahrenheit or Celsius. This option can be set in the INSTALLER/CONFIGURATION MENU of your thermostat. See page 6 step 12. Do I have to program a stop time for each program period? My thermostat does not follow it s program. What should I do? Between heating and cooling seasons, I want to turn my system off. Will this change my program? My display light does not work. Can it be fixed or replaced? Do I have to reprogram my thermostat after I change the batteries? My setpoint temperature is flashing. What does that mean? How can I get a copy of the Operating Manual for my thermostat? My program or configuration menu is all messed up, how do I start from the beginning? There is no need to select a time to stop a programming period. Starting a new programming period will stop the previous program period. Unless the thermostat appears to be damaged it will follow the program that is in the memory. The most common reason a thermostat will appear not to be following the program is a programming error. Verify that the AM or PM settings are correct for each period. Also verify that the Day of the week is set correctly. Models with EMR (Energy Management Recovery) start early to make the temperature they are programmed for by the time specified in the program. See the CONFIGURATION MENU on page 6 step 3. Any time you wish to turn your system off, simply press the button until OFF is displayed. This will not affect your thermostat s programming in any way. To turn the system back on, press the button to HEAT or COOL and press RUN. The system will begin operating according to the current thermostat program. See under OPERATION page 8 & 9. Because it is soldered to the circuit board it is not possible to repair or replace. No. This thermostat has permanent memory, although you will have to reset your clock. When the thermostat compressor time delay occurs it will flash the setpoint for about five minutes. This is intended to help protect the compressor from short cycling. Visit our website at www.white-rodgers.com for operating manuals. You can perform software reset by pressing and buttons simultaneously when mode is OFF. See Forget Keypad Lockout Code under TROUBLESHOOTING for details. HOMEOWNER HELP LINE: 1-800-284-2925 The Emerson logo is a trademark and service mark of Emerson Electric Co. St. Louis, Missouri Markham, Ontario www.white-rodgers.com