Under Water LED Universal Pool Light

Similar documents
WC2 & WC3 Installation & Maintenance Instructions

HEAT GUN KIT HG 2000K

CERAMIC HEATER MODEL NO: DEVIL 350B 230V/110V OPERATING & MAINTENANCE INSTRUCTIONS PART NO: & ORIGINAL INSTRUCTIONS GC ISS 1

Flo~mate Mains Boost Pump Installation & Maintenance Instructions

NON-SUBMERSIBLE WATER PUMP

Model 3.6m. User Manual Original instructions

HULME MARTIN HEAT SEALERS

Space Saver. Installation and user manual SS3 SS5 SS7 SS9. Issue 001 September 2017 ENGLISH UK IRL SmithsEP.co.uk

User Guide. For THE SWIMSUIT DRYER. Swimsuit Dryer manual Final 120v 60Hz. Copyright 2017 Page of 20

PHOTECH AMPHIBIOUS PA35/PA320/PA520 THE POND MASTERS GUIDE TO. Blagdon - The Pond Masters The name you can rely on

Space Saver. Installation and user manual. Issue 001 March 2018 ENGLISH UK IRL SmithsEP.co.uk. Issue March 2018 smithsep.co.

Flomate Mains Boost Pump Installation & Maintenance Instructions

SUBMERSIBLE WATER PUMPS

Installation Instructions & Operating Manual

SUBMERSIBLE DIRTY WATER PUMP

BOILING UNIT REDITAP. Installation and User Guide. IMPORTANT: This booklet should be left with the user after installation and demonstration

Premier Hazard STC Instructions

Inspect bath carefully and report any damage or faults before installation. No claims can be entered in to after installation.

CLEAN WATER PUMP. MODEL No: Hippo4A OPERATION & MAINTENANCE INSTRUCTIONS. Part No:

18W Round LED Wall/Ceiling Light with Microwave Sensor

User Guide. For THE SWIMSUIT DRYER. Swimsuit Dryer manual Final. Copyright 2014 Page of 20

Contact Details. Please note that some of the contact details on this PDF document may not be current.

I n s t r u c t i o n m a n u a l f o r b u i l t - i n h o o d. Model code: BORA600

OPERATION & MAINTENANCE INSTRUCTIONS

Use numbers given in the box to complete the following sentences. In the UK, the mains electricity supply is volts.

CPE RANGE PUMPS CPE RANGE PUMPS. MODEL Nos: CPE15A1 15A3 20A1 20A3 30A1 30A3 PART Nos:

CLARE G2000. Comprehensive Test Station for The Lighting Association Code of Practice. Operator Manual. February Clare Instruments Ltd.

air pump 2700/4500 ? 2YEAR GUARANTEE UK AIRPUMP _33435 CASC /10/ :16 Page 1

10yr O2NE & Safe-Ox. User Manual

INSTRUCTIONS MODEL: MWBT

Glue Gun 25W TTB580HTL. Barcode: WARNING: Read the instructions before using the product!

HEAVY DUTY BRASS SHOWER PUMPS

Instruction Manual M6627 / Version 7.4. Slide Drying Bench MH6616 MH6616X1

INSTRUCTIONS. MODEL: CPC and CPC1 PIE CABINETS

User Guide and Important Warranty Information. Suprima HE. Condensing Central Heating Boiler. Please read this document and keep it safe.

12W Round LED Wall/Ceiling Light with Microwave Sensor

MAINS KLARGESTER SEPARATOR ALARM INSTALLATION & OPERATIONS MANUAL

Electronic Thermostat With RF

CENTRIFUGAL PUMPS OPERATING INSTRUCTIONS

INSTALLATION INSTRUCTIONS SAFETY INSTRUCTIONS USER INSTRUCTIONS PIE CABINET

HULME MARTIN HEAT SEALERS

Digital Electronic Thermostat With RF

12/50 CENTRIFUGAL PUMPS FOR DC SUPPLY OPERATING INSTRUCTIONS

DANESMOOR FRONT SERVICE (FS) 12-18, FLOOR-STANDING OIL-FIRED PRESSURE-JET BOILERS USER INSTRUCTIONS & CUSTOMER CARE GUIDE

Digital Electronic Thermostat With RF

TIMEGUARD WEATHERSAFE OUTDOOR POWER RANGE INSTALLATION & OPERATING INSTRUCTIONS

Motion tracking. sensor led light. Installation & operating manual NIGHTWATCHER. Model no: nw1200x

Pasto Sous vide water bath

Installation Instructions For Monsoon Extra Pressure Sets:

Complete the table to show which size fuse, 3 A or 13 A, should be fitted to each of the appliances. Appliance Power Fuse

Kitchen Appliance Lift INSTRUCTION MANUAL

Utility Master. Steam cleaner. User Guide. Performance is everything. S10 Series. vax.co.uk

CENTRIFUGAL PUMPS OPERATING INSTRUCTIONS

INSTALLATION AND INSTRUCTION MANUAL IMPORTANT PLEASE READ:

Installation Instructions For Showermate Eco Shower Booster Pumps S1.5 bar Twin, S2.0 bar Twin, S2.0 bar Single

Installation, Operation & Maintenance Instructions

pond and garden LED feature light

INSTRUCTIONS NACHO WARMER MODELS: 1995 / 1995S

VACUUM EXTRACTOR MODEL NO: CWVE1 OPERATING & MAINTENANCE INSTRUCTIONS PART NO: GC0916

24 & 30 Drum Fan. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference

2.8KW ELECTRIC FAN HEATER

OWNERS INSTRUCTION MANUAL

Compact Movement Activated Sensor Installation Instructions

Aqua Dri AIR MOVER / CARPET DRIER SAFETY, OPERATION & MAINTENANCE INSTRUCTIONS

INSTALLATION INSTRUCTIONS SAFETY INSTRUCTIONS USER INSTRUCTIONS DRY BAIN MARIE

INSTALLATION INSTRUCTIONS POINT OF USE WATER HEATERS EPU - HW

Contents. Commissioning 6 Operation 6 Routine Preventative Maintenance 6 Fault Finding 7 Spares Parts 8 Technical Support 9

Model No: Little Devil II (inc ss)

Pond Oxygenator. Single / Twin / Four.

DANESMOOR 12-14, 15-19, 20-25, 26-32, 32-50, FLOOR-STANDING OIL-FIRED PRESSURE-JET BOILERS USER INSTRUCTIONS & CUSTOMER CARE GUIDE

14300 MAINS SEPARATOR ALARM MANUAL

1300W Pressure Washer RACHP133A

POWER SHOWERS Models 4500M 5002M 4500T 5002T

OPERATING & MAINTENANCE INSTRUCTIONS

Version 1.1. S88 W1M-B User Guide _User guide 25/02/ :03 Page 12

INSTRUCTION MANUAL IS-mB1 Minialite Intrinsically Safe Round LED Beacon

Built in Electric Ceramic Hob. Instruction Manual

Instructions for the heat exchanger control system SILVER C RX, RECOnomic, sizes 100/120, RECOsorptic, sizes

Carbon Film Installation Instructions

INSTRUCTIONS MODEL: P9EO

VADA - V80-H PRODUCT OVERVIEW CONSTRUCTION USAGE LIMITATIONS MOTOR WARRANTY

INSTRUCTIONS MODEL: CBM / CMB2

V80-H Multistage Pump Instruction Manual

2 KW OIL FILLED RADIATOR

DETECTOR TRANSMITTER INSTALLATION & OPERATING. Cat No. TLTX2000B INSTRUCTIONS

INSTRUCTIONS MODEL: MFBU WET WELL BAIN MARIE

ANNEALING FURNACE MODEL 414 User Maintenance Manual/Handbook

GEM-C Wireless User & Installation Manual. Revision October Apollo Solar Electric Limited. Documentation

PERFORMANCE SHOWER PRODUCTS

DEVIL CERAMIC SPACE HEATERS

Pie Warmer. Instruction manual. Model: GF454-A/GF455-A

User s Operation Instructions & Important Warranty Information

Congratulations on your Alert- it purchase

01 Safety. IMPORTANT Be sure to have read and understood these instructions before beginning the installation process.

HOT CUPBOARD WITH BAIN MARIE

RFM Series RFM-ISR Barrier. Installation Manual

Avanta 12v - 15v - 18v - 24v - 30v

With a power output ranging from 13kW to 24kW, they provide the flexible answer for the majority of traditional installation scenarios.

INSTALLATION INSTRUCTIONS POINT OF USE WATER HEATERS EPU - US10 EPU - US15

EASYCLEAR 3000 YEAR GUARANTEE

Transcription:

Under Water LED Universal Pool Light

2

3 Installation Instructions for LED lights This equipment is to be installed by a person qualified in electrical and plumbing systems Technical Data LED lights Dimensions Power requirement Power consumption Operating temperature Colours available 170mm dia x 24mm deep IP68 Stainless Steel & acrylic enclosure 12 Volts AC 40VA 54 Watts 0-40 degrees centigrade Amber, Blue, Cyan, Green, Red, Red / Orange and White Multi colour option CE Certificate Declaration of conformance Manufacturer's Name Topline Electronics Ltd Manufacturer's Address Unit A8, Ropemaker Park Hailsham, E.Sussex England, BN27 3GU Declares that the product conforms to the following product specifications: Low Voltage Directive 72/73 EEC Electromagnetic Compatibility Directive 2004/108/EC Restriction of Hazardous Substances (RoSH) Directive 2002/96/EC LED Directive IEC/EN60825-1 Waste Electrical and Electronic Equipment (WEEE) Directive 2002/95/EC CE marking. I the undersigned, declare that the equipment above conforms to the above directives and carries the CE marking. Manufacturer Topline Electronics Ltd Signature on behalf of Topline Electronics Ltd A.Hunt Date Feb.10th 2007

4 Installation Instructions The Underwater lights are designed to fit the Topline, Certikin, Astral or Aqua Pharris light niche. When installed in other manufacturers light niches an adaptor plate may be required, contact Topline on 01323-440760 for further information. Power Requirements Only qualified and competent electricians working to the 17th Edition of Electrical Regulations should install electrical equipment. The lights are powered via a transformer supplied by Topline when required. If connecting to another manufactures transformer please contact Topline for advice. Each light should have its own supply from the transformer and be suitably protected. Conductor size used should be 1mm min. The mains supply to the transformers should be fed by a fused isolator protected by a residual current device. Topline Transformer Connections There are two models of transformers supplied by Topline. A transformer that will supply 1 Topline LED unit and a transformer that will supply up to 8 Topline LED lights. See below for wiring information. To ensure clean switching of the lights a normally closed push button switch of the correct rating should be used between the RCD and transformer. 8 Way Transformer Wiring

5 1 Way Transformer Wiring Connections to LED Light The feed wire from the plant room to the LED light should be made in PVC wire 1mm CSA min. The light unit is supplied with a cable attached, this should be joined to the feed cable via a waterproof connector (IP68) or sealed gland unit (IP69 supplied by Topline if required). Ideally the junction from the plant room and each light should be made at pool surround level. If this is not possible then Topline can supply an underwater connector, installation instructions are detailed. This connector is also suitable for refurb installs and the instructions should be followed in full.

6 Topline LED Pool Lights Cable Connector Fitting Under water cable joints should be avoided if at all possible. In all cases when the joint is made under water, then the below unit should be used.

7 Installation of LED lights into Aqua Pharos Niche When installing the Topline LED light in to the Aqua Pharos niche the outer ring supplied by Aqua Pharos will need retaining. Assemble the light per below picture using Topline part 9944 and M5*35 s/s posi pans. The assembled unit then fits into the Aqua Pharos ring in the same way the Aqua Pharos light unit is installed.

8 Installation of LED lights into Certikin Niche When installing the Topline LED light in to the Certikin niche the outer ring supplied by Certikin should be replaced. Assemble the light per below picture using Topline part 9951 and M4*12 s/s posi pans. The assembled unit then fits into the Niche in the same way as the standard Certikin light

9 Installation of LED lights into Astral Niche When installing the Topline LED light in to the Astral niche the Topline LED light is supplied already installed into an Astral lamp holder. The assembled unit then fits into the Niche in the same way as the standard Astral light The type of niche needs to have been specified at the time of ordering, this will dramatically reduce on site installation time.

10 Commissioning of the LED Light Commissioning procedure Check that the light unit is secure in the underwater housing and that the electrical installation meets the requirement of the 16 th addition of the electrical regulations. NEVER OPERATE THE LIGHT WHEN IT IS NOT SUBMERSED. The light can be damaged beyond repair if this condition is not met. Check for handling damage, if there are any signs of damage replace unit. Turn on the underwater lights and check that all of the individual LED lights are on and that there is no trace of water within the unit. Commissioning Check list 1.Electrical supply 2.Cable to lights 3.Lights submersed 4.Damage to unit 5.All LEDs on 6.Leaks 1.Electrical supply 2.Cable to lights 3.Lights submersed 4.Damage to unit 5.All LEDs on 6.Leaks 1.Electrical supply 2.Cable to lights 3.Lights submersed 4.Damage to unit 5.All LEDs on 6.Leaks 1.Electrical supply 2.Cable to lights 3.Lights submersed 4.Damage to unit 5.All LEDs on 6.Leaks Light 1 Light 2 Light 3 Light 4 Light 5 Light 6 Light 7 Light 8 Light 9 Light 10 Light 11 Light 1 Light 13 Light 14 Light 15 Light 16 Light 17 Light 18 Light 19 Light 20 Notes reference above numbers

11 ACCEPTANCE of EQUIPMENT THE COMMISSIONING SHEET AND THIS SHEET ARE TO BE REMOVED AND RETURNED TO TOPLINE OR COMMISSIONING AGENT No person should sign this commissioning sheet unless they are completely satisfied with the equipment supplied. Signing of this commissioning sheet means that you accept the equipment and have understood the Health and Safety Warning, Risk Assessment and Operations Manual. The LED lights system is now yours and you are responsible for its maintenance and operation. Site... Address......... Client (site) representative... Telephone... Fax... Commissioned by... Date... Pool? Number of lights Serial No (from-to) Colour? Transformer? Hand over procedure Explain and or demonstrate: 1. How to turn on the lights. 2. Explain that operating the lights out of water will damage the unit. 3. That the electrical installation should be tested every 12 months. 4. Show Risk assessment and Health and Safety sheet to staff. 5. Ask everyone if they have any questions and have understood all they have been told.

12 TWENTY FOUR MONTH GUARANTEE Product Valid from Purchased From Installed by-: Commissioned by-: Your new Topline Product carries a full 24 month guarantee against faulty materials and workmanship. In the unlikely event that you have cause to complain during this period you should contact Topline Electronics Ltd. Unit 7, Crown Close, Hailsham, East Sussex. BN7 3JF. Tel: 01323 440760. We will replace components or the equipment, without charge. Provided that:- Approved agent carried out the Commissioning and that the commissioning sheet has been returned to Topline. The Operating Instructions (provided with Equipment) have been followed. Unit always operated submersed. All routine maintenance as been carried out. Service Components installed are approved by Topline Electronics Ltd. The Product has not had a repair attempted by others. The Product has not been damaged, abused or altered, The Product is being used for the purpose it was intended for. We reserve the right to use substitute Components of similar or higher quality. This Guarantee does not affect your statutory rights. PRODUCT SUPPORT. Our Technical Helpline 01323 440760 can provide assistance during office hours.

13 Operating Instructions The underwater LED pool unit is designed to provide reliable underwater lighting. It is advisable that when the lights are not required they are switched off. This will decrease electricity consumption still further and prolong service life. Colour change Mode (If available) To control the colour or control the sequence, turn the light off and on within 1 seconds. If the light is turned off for more than 10 seconds then when turned back on the light will resume the last selected sequence. The colour changing light has the following sequences available: Single Colours 1. White Only. The light will stay on white without any changes. 2. Red Only. The light will stay on red without any changes. 3. Green Only. The light will stay on green without any changes. 4. Blue Only. The light will stay on blue without any changes. 5. Yellow Only. The light will stay on yellow without any changes. 6. Purple Only. The light will stay on purple without any changes. 7. Turquoise Only. The light will stay on turquoise without any changes. Colour Change 8. Colour Fade Blue to Green (Lights not synchronised) The light will change from blue to green. If there is more than one light in the pool, lights will not display the same colour. 9. Colour Fade Green to Red (Lights not synchronised) The light will change from green to red. If there is more than one light in the pool, lights will not display the same colour. 10. Colour Fade Red to Blue (Lights not synchronised) The light will change from red to blue. If there is more than one light in the pool, lights will not display the same colour. 11. Colour Fade all colours (Lights not synchronised) The light will fade through all colours. If there is more than one light in the pool, lights will not display the same colour. 12. Colour Flash all colours (Lights not synchronised) The light will flash through all colours. If there is more than one light in the pool, lights will not display the same colour. 13. Colour Fade and lock (Lights syncronised) The light will fade through all colours. Once you reach a colour, you can turn the lights on and off quickly and the lights will remain locked on that colour. 14. Colour Fade all colours (Lights synchronised) The light will fade through all colours. If there is more than one light in the pool, lights will display the same colour. 15. Colour Flash all colours (Lights synchronised) The light will flash through all colours. If there is more than one light in the pool, lights will display the same colour.

14 Routine Servicing The only routine servicing required is the cleaning of the front lens and the checking of the electrical installation every 12 months. Use a soft sponge to clean the lens whilst the unit is still underwater. Health and Safety Warning You should not look directly at the light unit when it is switched on. The equipment must not be operated when out of water. The front will get very warm. The equipment must always be protected electrically. Remember, if something is wrong with the system TAKE THE APPROPRIATE ACTION! Do not just record a fault and walk away. Risk Assessment There is no significant risk when operating the equipment. The front of the light can get warm, but only when operated out of water. The light should not be viewed directly, there is a risk to the eyes.

15 Trouble shooting Before contacting Topline for technical advice, please ensure you make a note of, what the problem is. SYMPTOM PROBLEM REMEDY 1 ALL LIGHTS OFF TURNED OFF TURN ON CABLE FAULT CONTACT TOPLINE TRANSFORMER FAULT CONTACT TOPLINE 2 ONE LIGHT OFF CABLE FAULT CONTACT TOPLINE TRANSFORMER FAULT CONTACT TOPLINE LIGHT FAULT CONTACT TOPLINE 3 NOT ALL LED LIGHTS ARE ON FAULT WITH LED UNIT CONTACT TOPLINE WITHIN A LIGHT UNIT Servicing including calls made under guarantee SERVICE METHOD STATEMENT Telephone Contact 01323-440760. The number will be manned between 09.00hrs and 17.00hrs Monday to Friday excluding Bank Holidays (Answer phone at all other times redirecting to a mobile number). First action will be to discuss the situation and to try and find a resolution over the telephone. If required a Topline Engineer will attend site as detailed below, in accordance with the Service Price List or Service Agreement, an estimated time of arrival will be given. Parts and equipment are supplied as detailed in the Price List, special Discounts may apply by prior arrangement. VAT is at the prevailing rate in addition to our charges. We aim to provide a fast and efficient Service, if the site is experiencing difficulties with Pools and Spa s outside our remit we will make our resources available to help find a solution. Topline will review all statements and prices from time to time, we reserve the right to make changes when necessary. WARRANTY The LED is supplied with a two year parts and labour return to Topline warranty. Topline Electronics Limited Unit A8 Ropemaker Park Diplocks Way Industrial Estate Hailsham, East Sussex BN27 3GU Tel: 01323 440760 Fax: 01323 844508 Email: sales@topline.uk.net Internet: www.topline.uk.net