.devicemanuals.eu
@ SuperQuick 15 30 C Before ashing for the first time Risk of poisoning Keep detergents and care products out of the reach of children. Risk of explosion Items of laundry pretreated ith cleaning agents containing solvents, e.g. stain remover / cleaning solvent may lead to an explosion after being loaded into the ashing machine. Rinse items of laundry thoroughly by hand beforehand. Risk of injury *880897* Keep packaging, film and packaging parts out of the reach of children. The ashing machine door can become very hot. Be careful hen draining hot detergent solution. Do not climb onto the ashing machine. Do not lean on the open ashing machine door. Do not reach into the drum if it is still rotating. Be careful hen opening the detergent draer hile the machine is in operation. Consumption values Programme Load Additional function... if it contains detergent or fabric softener residues. 1. Pull the draer out, press don the insert and fully remove the draer from the housing. 2. To remove the insert: press the insert upards from belo ith your finger. 3. Clean the detergent dispenser tray and insert ith ater and a brush and dry it. Also remove any detergent or fabric softener residues in the housing. 4. Attach the insert and engage (connect the cylinder to the guide pin). 5. Push in the detergent draer. 3. Carefully unscre the pump cover (residual ater). 4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution pump must rotate). 5. Replace the pump cover and scre it tightly. 6. Place the service flap back on and close. Leave the detergent draer open so that any residual ater can evaporate. Washing drum and rubber seal Electricity*** Descaling Water*** Load Annual energy consumption Ensure there is no laundry in the machine Descale the appliance according to the descaler manufacturer's instructions. This should not be necessary if the correct dosage of detergent is used. Programme duration*** Emergency release, e.g. in the event of a poer cut Drainage hose at the siphon Turn the programme selector to Off and disconnect the mains plug. 1. Loosen the hose clamp, carefully remove the drainage hose (residual ater). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection ith the hose clamp. Filter in the ater supply.d Information on the display panel Annual ater consumption 8 F: 16 F: 17 F: 18 F: 21 F: 23 depending on model Close the ashing machine door properly; laundry may be caught. Open the tap completely, supply hose kinked or trapped; Clean the filter a page 10, Water pressure too lo. Detergent solution pump blocked; Clean the detergent solution pump a page 10. Drainage hose / aste pipe blocked; Clean the drainage hose at the siphon a page 10. Motor fault. Call customer services. Water in the base tub, appliance leaking. Call customer services. 9 To prevent unused detergent from floing straight into the drain during the next ash: Pour 1 litre of ater into compartment II and start the > Drain programme. Risk of electric shock! Do not immerse the HydroSafe safety device in ater (contains an electric valve). The programme continues to run hen the poer has been restored. Hoever, if the laundry has to be removed, the ashing machine door can be opened as follos: Risk of scalding. The detergent solution and laundry may be hot. If possible, leave it to cool don. Do not reach into the drum if it is still rotating. Do not open the ashing machine door if ater can be seen through the glass. 1. Turn the programme selector to Off and disconnect the mains plug. 2. Drain the detergent solution a page 10. 3. Pull the emergency release donards ith a tool and release. Washing machine door can then be opened. LF Cottons 40/60 C ć EcoPerfect** 3,5/ 165 kwh 10686 l ** Programme setting for testing and energy labelling in accordance ith EU directive 2010/30/EU ith cold ater (15 ºC). *** The values deviate from the indicated values depending on ater pressure, hardness, and inlet temperature, ambient temperature, type, amount and soiling of the laundry, detergent used, fluctuations in the poer supply and selected additional functions. 7 2* For models ithout a drainage hose: Carefully unscre the pump cover until the detergent solution begins to flo out. When the service flap is half full, close the pump cover and empty the service flap. Repeat the above steps until all the detergent solution has completely drained out. Wipe the inside of the rubber seal dry ith a cloth. Leave the ashing machine door open so that the drum can dry out. Rust stains - use chlorine-free cleaning agent, not steel ool. L Cottons 20 C 0,32 kwh 68 l 2½h L Cottons 30 C 0,56 kwh 68 l 2½h L Cottons 40 C* 0,91 kwh 68 l 2½h L Cottons 60 C 1,25 kwh 68 l 2¾h L Cottons 90 C 2,16 kwh 74 l 2¾h Easy-Care 40 C* 3 kg 0,55 kwh 54 l 1¾h / Mixed Load 40 C 3 kg 0,45 kwh 35 l 1¼h cdelicate/silk 30 C 2 kg 0,24 kwh 35 l ¾h : / /cwool 30 C 2 kg 0,22 kwh 47 l ¾h * Programme setting for testing in accordance ith valid standard EN60456. Note on comparative tests: For testing the test programmes, ash the specified load using the maximum spin speed. Programme Wipe ith a soft, damp cloth. Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners). Remove detergent and cleaning agent residue immediately. Do not clean ith a jet of ater. Cleaning the detergent draer and housing... depending on model 2. For models ith a drainage hose: Remove the drainage hose from the retainer and pull it from the housing. Remove the container. Remove the sealing cap, allo the detergent solution to flo out. Replace the sealing cap and place the drainage hose in the retainer. u Danger of suffocation Turn the programme selector to Off and disconnect the mains plug. 1. Open and remove the service flap. Machine housing, control panel.e For orn-out appliances: Disconnect the mains plug. Sever the mains cable and discard along ith the plug. Destroy the lock on the ashing machine door. This ill prevent children from locking themselves in and risking their lives. What to do if... an ua ls Danger to life Do not load any laundry into the machine. Turn on the tap. Add the folloing to compartment II: approx. 1 litre ater detergent (dosage according to the manufacturer's instructions for light soiling and the appropriate degree of ater hardness) Set the programme selector to L Cottons 60 C and select $ Start/Reload. At the end of the programme, turn the programme selector to Off. m Never pull the cable to disconnect the mains plug. Never insert/disconnect the mains plug ith damp hands. Risk of scalding. Allo the detergent solution to cool don. Turn off the tap. Detergent solution pump ce WAE24369GB... Risk of electric shock Maintenance Risk of electric shock. Disconnect the mains plug. Risk of explosion. No solvents. ev i Robert Bosch Hausgeräte GmbH Carl-Wery-Str. 34 81739 München / Deutschland Care Read the instruction manual and installation instructions and all other information enclosed ith the ashing machine and act accordingly. Retain the documents for subsequent use. 9303 / 9000880897 2 kg cold, 30 C : / / Wool cdelicate/silk 30 C 3 kg 40 C / Mixed Load 30, 40 C I Easy-Care Additional 2 Rinse/ cspin, > Drain programmes * Reduced load for additional Ĉ SpeedPerfect function As a short programme, / Mixed Load 40 C, ith a maximum spin speed, is ideal. Programmes ithout pre-ash - add detergent to compartment II, programmes ith pre-ash - distribute the detergent beteen compartments I and II. Ĉ SpeedPerfect, ć EcoPerfect, S Reduced Ironing, = Aqua Plus Ĉ SpeedPerfect, ć EcoPerfect, S Reduced Ironing, Fabrics made of cotton or easy-care fabrics = Aqua Plus; different types of laundry can be ashed together For delicate, ashable fabrics, e.g. made of silk, satin, Ĉ SpeedPerfect, ć EcoPerfect, S Reduced Ironing, = Aqua Plus; synthetic fibres or blended fabrics (e.g. curtains) No spin beteen rinse cycles Handä or machine-ashable fabrics made of ool or Particularly gentle ash programme to avoid shrinkage of laundry, longer programme breaks (fabrics rest in the detergent containing ool solution) Easy-care fabrics made of cotton, linen, synthetic Short programme, approx. 15 minutes, fibres or blended fabrics suitable for lightly soiled laundry Easy-care fabrics made of cotton, linen, synthetic fibres or blended fabrics Ĉ SpeedPerfect*, ć EcoPerfect, S Reduced Ironing, = Aqua Plus Hard-earing fabrics, heat-resistant fabrics made of cotton or linen L Cottons + Preash 20, 30, 40, 60, 90 C 40 C / 4 kg* Additional functions; information Type of laundry max. C Programmes a Refer to the table of consumption values on page 8 and notes on page 6. Overvie of programmes Safety instructions 1. 2. 3. 4. Reduce the ater pressure in the supply hose: Turn off the tap. Select any programme (except for 2 Rinse/ cspin // > Drain). Choose $ Start/Reload. Let the programme run for approximately 40 seconds. Turn the programme selector to Off. Disconnect the mains plug. Clean the filter: 1. Depending on model: Disconnect the hose from the tap. Clean the filter using a small brush. and/or for Standard and Aqua-Secure models: Remove the hose on the rear of the appliance, Remove the filter ith pliers and clean. 2. Connect the hose and check for leaks. 10 Water is leaking out. No ater supply. Detergent not dispensed. Washing machine door cannot be opened. Programme does not start. Detergent solution is not drained. Water not visible in the drum. Unsatisfactory spin result. Laundry et/too damp. The programme duration changes during the ash cycle. Spin cycle performed several times. Residual ater in the compartment for care products. Odour formation in the ashing machine. Status display³ 1 flashes. Foam may be coming out of the detergent draer. Intense noise formation, vibrations and andering during the spin cycle. Noises during spin and drain cycles. Display panel/indicator lamps do not function during operation. Programme sequence longer than usual. Attach/replace the drainage hose correctly. Tighten the scre connection of the supply hose. $ Start/Reload not selected? Tap not turned on? Filter blocked? Clean the filter a page 10. Supply hose kinked or trapped? Safety function active. Programme stopped? a page 4. Is Rinse Hold (ithout final spin) selected? a page 3, 4. Can be opened by emergency release only? a page 9. $ Start/Reload or Ready in time selected? Washing machine door closed? Childproof lock active? Deactivate a page 5. Is Rinse Hold (ithout final spin) selected? a page 3, 4. Clean the detergent solution pump a page 10. Clean the aste pipe and/or drainage hose. Not a fault - ater belo the visible area. Not a fault - the unbalanced-load detection system has cancelled the spin cycle because of uneven distribution of the laundry. Distribute small and large items of laundry evenly inside the drum. S Reduced Ironing selected? a page 5. Selected speed too lo? a page 5. Not a fault the programme sequence is optimised for the particular ash process. This may result in changes to the programme duration in the display field. Not a fault - unbalanced load detection system adjusts the imbalance. Not a fault - the action of the care product is not affected. Clean the insert if necessary a page 9. Run programme L Cottons 90 C ithout laundry. Use standard detergent. Too much detergent used? Mix 1 tablespoon of fabric softener ith ½ litre of ater and pour into dispenser II (not for outdoor and donfilled textiles!). Reduce the detergent dosage for the next ash cycle. Are the appliance feet fixed? Secure the appliance feet a Installation instructions. Transportation safety devices removed? Remove the transportation safety devices a Installation instructions. Washing machine Clean detergent-solution pump a page 10. Poer cut? Fuses triggered? Reset/change the fuse. If the fault occurs repeatedly, call customer services. Not a fault - unbalanced load detection system adjusts imbalance by repeatedly distributing the laundry. Not a fault - foam detection system active - adds an additional rinse cycle. Detergent residues Occasionally, phosphate-free detergents contain ater-insoluble on the laundry. residues. Select the 2 Rinse/ cspin cycle or brush out the laundry after ashing. If you cannot correct a fault yourself (sitching on/off) or a repair is required: Turn the programme selector to Off and remove the mains plug from the socket. Turn off the ater supply and call customer services a Installation instructions. 11 en Instruction manual
.devicemanuals.eu
.devicemanuals.eu
.devicemanuals.eu
.devicemanuals.eu
Care Maintenance Risk of electric shock. Disconnect the mains plug. Risk of explosion. No solvents. Before ashing for the first time Detergent solution pump Do not load any laundry into the machine. Turn on the tap. Add the folloing to compartment II: approx. 1 litre ater detergent (dosage according to the manufacturer's instructions for light soiling and the appropriate degree of ater hardness) Set the programme selector to L Cottons 60 C and select $ Start/Reload. At the end of the programme, turn the programme selector to Off. Turn the programme selector to Off and disconnect the mains plug. 1. Open and remove the service flap. 2. For models ith a drainage hose: Remove the drainage hose from the retainer and pull it from the housing. Remove the container. Remove the sealing cap, allo the detergent solution to flo out. Replace the sealing cap and place the drainage hose in the retainer. Machine housing, control panel Wipe ith a soft, damp cloth. Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners). Remove detergent and cleaning agent residue immediately. Do not clean ith a jet of ater. 2* For models ithout a drainage hose: Carefully unscre the pump cover until the detergent solution begins to flo out. When the service flap is half full, close the pump cover and empty the service flap. Repeat the above steps until all the detergent solution has completely drained out. u Cleaning the detergent draer and housing....e... if it contains detergent or fabric softener residues. 1. Pull the draer out, press don the insert and fully remove the draer from the housing. 2. To remove the insert: press the insert upards from belo ith your finger. 3. Clean the detergent dispenser tray and insert ith ater and a brush and dry it. Also remove any detergent or fabric softener residues in the housing. 4. Attach the insert and engage (connect the cylinder to the guide pin). 5. Push in the detergent draer. an ua ls 3. Carefully unscre the pump cover (residual ater). 4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution pump must rotate). 5. Replace the pump cover and scre it tightly. 6. Place the service flap back on and close. Leave the detergent draer open so that any residual ater can evaporate. To prevent unused detergent from floing straight into the drain during the next ash: Pour 1 litre of ater into compartment II and start the > Drain programme. m Washing drum and rubber seal ce Wipe the inside of the rubber seal dry ith a cloth. Leave the ashing machine door open so that the drum can dry out. Rust stains - use chlorine-free cleaning agent, not steel ool. Descaling Ensure there is no laundry in the machine ev i Descale the appliance according to the descaler manufacturer's instructions. This should not be necessary if the correct dosage of detergent is used. Drainage hose at the siphon Turn the programme selector to Off and disconnect the mains plug. 1. Loosen the hose clamp, carefully remove the drainage hose (residual ater). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection ith the hose clamp. Filter in the ater supply.d Emergency release, e.g. in the event of a poer cut Risk of electric shock! Do not immerse the HydroSafe safety device in ater (contains an electric valve). The programme continues to run hen the poer has been restored. Hoever, if the laundry has to be removed, the ashing machine door can be opened as follos: Risk of scalding. The detergent solution and laundry may be hot. If possible, leave it to cool don. Do not reach into the drum if it is still rotating. Do not open the ashing machine door if ater can be seen through the glass. 1. Turn the programme selector to Off and disconnect the mains plug. 2. Drain the detergent solution a page 10. 3. Pull the emergency release donards ith a tool and release. Washing machine door can then be opened. Information on the display panel F: 16 F: 17 F: 18 F: 21 F: 23 Risk of scalding. Allo the detergent solution to cool don. Turn off the tap. depending on model Close the ashing machine door properly; laundry may be caught. Open the tap completely, supply hose kinked or trapped; Clean the filter a page 10, Water pressure too lo. Detergent solution pump blocked; Clean the detergent solution pump a page 10. Drainage hose / aste pipe blocked; Clean the drainage hose at the siphon a page 10. Motor fault. Call customer services. Water in the base tub, appliance leaking. Call customer services. 9 1. 2. 3. 4. Reduce the ater pressure in the supply hose: Turn off the tap. Select any programme (except for 2 Rinse/ cspin // > Drain). Choose $ Start/Reload. Let the programme run for approximately 40 seconds. Turn the programme selector to Off. Disconnect the mains plug. Clean the filter: 1. Depending on model: Disconnect the hose from the tap. Clean the filter using a small brush. and/or for Standard and Aqua-Secure models: Remove the hose on the rear of the appliance, Remove the filter ith pliers and clean. 2. Connect the hose and check for leaks. 10
Washing machine.devicemanuals.eu en Instruction manual