Class 1 laser beam sensor safe for your eyes

1129 PHOTO PHOTO PARTICUR Sensor SERIES Related Information General terms and conditions... F-3 About laser beam... P.193~ guide... P.121~ General precautions... P.19 Conforming to FDA regulations (-11 only) MEASURE panasonic.net/id/pidsx/global Class 1 laser beam sensor safe for your eyes -1 is classified as a Class 1 Product in IEC / JIS standards. -11 is a Class I Product in FDA regulations. Do not look at the laser beam through optical system such as a lens. BASIC PERFORMANCE Safety countermeasures not required This laser collimated beam sensor conforms to the Class 1 laser stipulated in IEC 682-1 and JIS C 682. Hence, safety measures such as protective gear are not necessary. Precise sensing in wide area -1 FUNCTIONS Easy laser beam alignment Four monitoring LEDs help you to easily align the emitter and the receiver. front face DOWN lights up Sensing area: 1 mm.91 19.68 in Minimum sensing object: ø.1 mm ø. in Repeatability: 1 µm.39 mil or less VARIETIES FDA Class I type Sensing width 1 mm.91 in Sensing range mm 19.68 in Minimum sensing object ø.1 mm ø. in -11 LEFT lights up Versatile mounting RIGHT lights up UP lights up The monitoring system checks whether the incident beam falls evenly on all the four receiving elements in the receiver window. -11 conforms to FDA Class I. It is approved for use in U.S.A. by FDA. The side view attachment (optional) enables versatile mounting styles. Side view attachment

Sensor SERIES 113 APPLICATIONS Accurate positioning of orientation flat Counting number of O-rings Positioning gear on polishing machine Defective OK Defective Chuck Gear ORDER GUIDE PARTICUR collimated beam sensors Type Appearance Model No. Conforming standards / regulations Output Class 1 type Sensing range: mm 19.68 in Minimum sensing object: ø.1 mm ø. in Repeatability: 1 μm.39 mil or less Sensing width: 1 mm.91 in Emitting element: Infrared semiconductor laser diode (Class 1) -11 FDA regulations Note: The model No. with P shown on the label affixed to the product is the emitter, D shown on the label is the receiver. Accessory MS-1 (Sensor mounting bracket) -1 IEC and JIS standards NPN open-collector transistor (Comparative output) Analog voltage Output voltage: 1 to V Set of two L-shaped brackets and four M (length 8 mm.31 in) screws with washers. Note: 2 sets are required to mount the emitter and the receiver. Designation Model No. Description Side view attachment (Note 1) Digital panel controller (Note 2) -SV1 CA2-T2 Versatile mounting is possible as the laser beam can be bent at a right angle. Sensing range: mm 19.68 in Minimum sensing object: ø.1 mm ø. in Repeatability: 2 µm.787 mil or less This is a very small controller which allows two independent threshold level settings. Supply voltage: 2 V DC ±1 % No. of inputs: 1 No. (sensor input) Input range: 1 to V DC Output: NPN open-collector transistor Main functions: Threshold level setting function, zero-adjust function, scale setting function, hysteresis setting function, start/hold function, autoreference function, power supply ON-delay function, etc. Notes: 1) Mount -SV1 on either the emitter or the receiver. If it is mounted on both sides, the monitor LEDs may not light off perfectly. 2) Refer to p.113~ the ultra-compact digital panel controller CA2 series. Side view attachment -SV1 Two M3 (length 1 mm.39 in) screws with washers are attached. Digital panel controller CA2-T2

1131 Sensor SERIES SPECIFICATIONS PARTICUR collimated beam sensors Type Class 1 type Conforming standards / regulations IEC and JIS standards FDA regulations Item Model No. -1-11 CE marking directive compliance Sensing width Sensing range Min. sensing object Repeatability Supply voltage Current consumption Comparative output Utilization category Response time Output operation Short-circuit protection Analog output Slew rate Temperature characteristics Remote interlock input Indicators Adjusters Environmental resistance Operation emission warning Stable incident beam beam alignment Threshold level Span Pollution degree EMC Directive, RoHS Directive 1 mm.91 in mm 19.68 in ø.1 mm ø. in opaque object 1 µm.39 mil or less ±1 % Ripple P-P 1 % or less : 3 ma or less, : 2 ma or less NPN open-collector transistor Maximum sink current: 1 ma Applied voltage: 3 V DC or less (between comparative output and V) Residual voltage: 1 V or less (at 1 ma sink current). V or less (at 16 ma sink current) DC-12 or DC-13. ms or less ON when the incident beam amount is less than the threshold level Incorporated Analog voltage Output voltage: 1 V (Darkest) to V (Lightest) Output impedance: 7 Ω 8 V/ms or more Within ±.1 % F.S./ C (with respect to sensing range at ambient temperature 2 C 68 F) is emitted when it is connected to V, but not emitted when connected to V or kept open Red LED (lights up when the comparative output is ON) Red LED (lights up when laser is being emitted) Green LED (lights up under the stable light received condition) Yellow LED (light up when laser beam is misaligned) Adjustment of threshold level for the comparative output, 18-turn endless adjuster Adjustment of span for the analog voltage output, 18-turn endless adjuster 3 (Industrial environment) Ambient temperature to C to 122 F (No dew condensation allowed), Storage: 2 to 7 C to 18 F Ambient humidity Ambient illuminance Insulation resistance Vibration resistance Shock resistance Emitting element Enclosure earthing Material Cable Cable extension (Note 2) Net weight 3 to 8 % RH, Storage: 3 to 8 % RH Incandescent light: 1, lx or less at the light-receiving face 2 MΩ, or more, with 2 V DC megger between all supply terminals connected together and enclosure 1 to Hz frequency, 1. mm.9 in double amplitude in X, Y and Z directions for two hours each m/s 2 acceleration ( G approx.) in X, Y and Z directions three times each Infrared semiconductor laser diode (Maximum output: 1.7 mw, Peak emission wavelength: 78 nm.31 mil) Capacitor earth Enclosure: Die-cast zinc alloy, Top cover: PPO, Front protection cover: Glass.2 mm 2 -core (emitter: -core) shielded cable, 3 m 9.83 ft long Extension up to total m 16.2 ft is possible, for both emitter and receiver, with.3 mm 2, or more, cable. (Synchronization wire cannot be extended.) : 29 g approx., : 28 g approx. MS-1 (Sensor mounting bracket): 1 set for emitter and receiver Adjusting screwdriver: 1 pc. Accessories Crimp contact: 2 pcs. Class 1 identification label: 1 pc. (-1 only) Inspection slip: 1 pc. (-11 only) Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of 2 C 68 F. 2) -1 and -11 are CE compliant and complies with EMC directives. EN 61-6-2 is the applicable standard that covers immunities relating to use of this product, but in order to comply with this standard, the following conditions must be satisfied. Conditions This sensor should be connected less than 1 m.88 ft from the power supply. The signal line to connect with this sensor should be less than 3 m 98.2 ft.

Sensor SERIES 11 I/O CIRCUIT AND WIRING DIAGRAMS -1-11 collimated beam sensor I/O circuit diagram Enclosure Sensor circuit D Color code (Brown) V (Orange/Violet) Sync. *1 (Pink) Remote interlock ±1 % Wiring diagram Brown *1 Pink Blue ±1 % C (Blue) V Orange/Violet Enclosure Sensor circuit Internal circuit Tr D 7 Ω Z D1 Z D2 C Users circuit (Brown) V (Orange/Violet) Sync. (White) Analog voltage output (Black) Comparative output (Blue) V Load 1 ma max. ±1 % Orange/Violet Brown Black Load White To analog input circuit ±1 % PARTICUR Internal circuit Users circuit *1 Blue Symbols D : Reverse supply polarity protection diode ZD1, ZD2: Surge absorption zener diode C : Capacitor (.22 μf) Tr: NPN output transistor Remote interlock emission: Connection to V emission halt: Connection to V, or open SENSING CHARACTERISTICS (TYPICAL) Correlation between setting distance and excess gain Correlation between transverse deviation and output voltage Correlation between interrupted beam width and output voltage Correlation between ambient temperature and output voltage variation rate 1 8 8 1 Excess gain 1 1. 1.6 1 3.281 1..921 2 6.62 Setting distance L (m ft) 2. 8.22 Output voltage (V) 6 2 mm 19.68 in l 1 1.39.197.197.39 Left Center Right Deviation l (mm in) Output voltage (V) 6 2 (Lightest).197 1.39 1.91 2.787 (Darkest) Interrupted beam width D (mm in) Output voltage variation rate (%) 1 1 2 3 68 86 1 122 Ambient temperature ( C F)

1133 Sensor SERIES PRECAUTIONS FOR PROPER Refer to p.19 for general precautions and p.193~ for information about laser beam. PARTICUR collimated beam sensor This catalog is a guide to select a suitable product. Be sure to read the instruction manual attached to the product prior to its use. Never use this product as a sensing device for personnel protection. In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. This product is classified as a Class 1 Product in IEC / JIS standards and a Class I Product in FDA regulations. Do not look at the laser beam through optical system such as a lens. The following label is enclosed with this product. Handle the product according to the instruction given on the warning label. Class 1 type Mounting The emitter and the receiver must face each other with proper slit orientation so that the beam can be received. The tightening torque should be 1.17 N m or less. When mounting the sensor with the attached sensor mounting bracket, the sensor must be fixed on both sides. The English warning label based on FDA regulations is pasted on the FDA regulations conforming type. Align the slit orientation Sensor mounting bracket MS-1 (Accessory) Wiring In -1 and -11, capacitor earth is used to enhance the noise characteristics. In case there is a high frequency noise generating equipment, such as, an ultrasonic welding machine, etc., near the sensor head and if the mounting base is electrically conducting (metallic, etc.), then insulate the sensor head from the mounting base. Do not use a power supply having a single-winding transformer (auto-transformer) as this can be dangerous. Safety standards for laser beam products A laser beam can harm human being s eyes, skin, etc., because of its high energy density. IEC has classified laser products according to the degree of hazard and the stipulated safety requirements. -1 is identified as a Class 1 laser product. Classification by IEC 682-1 Classification Description s that are safe under reasonably foreseeable conditions of operation, Class 1 including the use of optical instruments for intrabeam viewing. Note: Refer to p.19 for information about for the classification in FDA regulations. Safe use of laser products For the purpose of preventing users from suffering injuries by laser products, IEC 682-1 (Safety of laser products). Please check the standards before use. (Refer to p.193~ for information about laser beam.) s The sensor s output is proportional to the amount of laser beam received. Since there is some variation in the light intensity at the center and the periphery of the sensing area, take care that output = dimension may not hold. For stable operation, use the sensor 1 min., or more, after switching on the power supply.

Sensor SERIES 113 DIMENSIONS (Unit: mm in) The CAD data can be downloaded from our website. -1-11 26 1.2 26 1.2 9..37 beam emitting part -M3..2, 6.236 deep 3 1.181 31.8 1.22 2-M.7.28,.17 deep MS-1 -SV1 26 1.2 7.276 1.969 2.2 1.6.16 19.78 7 2.93 7 9.276.3 emission warning indicator (Red).197 16.63 ø.7 ø.22 cable, 3 m 9.83 ft long 13.7.39 3.2.126 (3.2) (.126) 1.7 2-M.7.28, 1.39 deep (on both sides).17.2.16 13.12 2.787 7.276 t 1.6 t.63 Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated) Set of two L-shaped brackets and four M (length 8 mm.31 in) screws with washers 3.118 8.31 2-ø3. ø.13 mounting holes Mounting surface.197 for -1 or -11 (.6) (.2) axis Material: Glass (Front protection cover, Aluminum evaporated mirror) Polyetherimide (Enclosure) Two M3 (length 1 mm.39 in) screws with washers are attached. 26 1.2 3 1.181 12..88 12..88 beam alignment monitor 26 1.2 beam alignment monitor elements beam receiving part (1 1) (.91.39) -M3..2, 6.236 deep 1.8 1.66 2.8 1.16 31.8 1.22 2-M.7.28,.17 deep 13.12 7. 18..29.728..173 1.8.71 7 2.93 (72) 8 (2.83) 2.283 29 1.12 7 2.276.787 t 1.6 t.63 axis 7.8 1.882 axis collimated beam sensor 6.236 Threshold level adjuster 16.63 Span adjuster Operation indicator (Red).197 ø.7 ø.22 cable, 3 m 9.83 ft long 13.7.39 3.2.126 (3.2) (.126) 1.7 2-M.7.28, 1.39 deep (on both sides) Sensor mounting bracket (Accessory for -1 and -11) Assembly dimensions Assembly dimensions.17 27.8 1.9 (112) (.9) 7 2.93 19 7 9.78.276.3 1.969 13.12.2.16 7.276 23..92 Side view attachment (Optional).197 PARTICUR