FlaskScrubber & SteamScrubber Laboratory Glassware Washers! FlaskScrubber & SteamScrubber racks now interchangeable
FlaskScrubber Laboratory Glassware Washers General Features Patent-pending design Lower spindle rack, of Type 304 stainless steel, with 36 detachable large spindles for washing narrow-neck glassware. Eighteen glassware holders, 36 clips and 10 additional interchangeable small spindles are included. Rack accommodates a variety of inserts for holding beakers, culture tubes and other specialty glassware (inserts sold separately). See pages 6-7. Water temperature reaches 82 C (180 F) on 115 olt models and 93 C (199 F) on 230 olt models to sanitize glassware and for enhanced washing and faster drying LCD information center for customizing cycles and monitoring operation, including internal water temperature ( C or F) Water recirculation rates of 96 gal/min (363 liters/min) when operated on 115 olt, 60 Hz and 230 olt, 50 Hz and 112 gal/min (424 liters/min) on 230 olt, 60 Hz for thorough cleaning Dual pumps, one for washing and one for draining, to reduce potential for cross contamination Built-in purified water pump to bring non-pressurized or pressurized purified water into the tank for up to six pure water rinses Built-in steam generator that produces hot vapor to penetrate and remove dried residue for cleaner glassware Manual-fill detergent dispenser for powder or liquid detergent Manual-fill rinse aid solution dispenser Built-in forced air drying through the spindles up to 99 minutes and programmable from 38-70 C (100-158 F) Factory-set cycle programs. All 115 volt models have seven programs: RINSE ONLY, PLASTIC, GLASS, GLASS PLUS, SCIENTIFIC, SCIENTIFIC PLUS, and DRY ONLY. All 208/240 olt models have three additional programs for a total of ten: INTENSE, INTENSE PLUS and EXTREME. Alarms with display for HOT GLASS, PLEASE WAIT, WATER LOW, WATER HIGH and OERFLOW Two user-set cycle programs User-set delayed start (up to 8 hours) Type 304, brushed stainless steel door, tank, upper and lower wash arms. Freestanding models also have stainless steel exterior sides and top. One-piece, stainless steel, fine mesh particle drain filter to trap debris in tank to protect the pumps No center water distribution tower allowing for greater glassware capacity Four leveling feet 3/8" Female NPT inlet fitting for hot tap water connection FlaskScrubber Laboratory Glassware Washer 4420430 Factory-installed drain hose and band clamp Two year warranty on parts and labor Made in the U.S.A. IQ/OQ available on line. Contact Labconco about on-site validation service (sold separately). Accommodate optional Upper Spindle Rack with additional wash arm and side release latches. See page 6. More versatility. Accommodate optional Upper and Lower Standard Racks. See page 6. Requirements Minimum inlet water temperature 49 C (120 F) Recommended inlet water temperature 60 C (140 F) Minimum purified water pressure 0 psi Water consumption per fill 3.4 gallons (13 liters) Hot tap water pressure at the washer 20-120 psi Hot tap water flow rate 1.25 gallons (4.7 liters) per minute 3/8" OD copper tubing for connection to the water inlet valve Purified water with supply piping minimum 3/8" ID to permit at least 0.9 gallon (3.4 liters) per minute flow Exclusive Labconco feature Catalog # Style Electrical Maximum Internal iewing Window Overall Dimensions Shipping Requirements Water Temperature and Light with Door Closed Weight 2 4420320 Undercounter 115 volts, 60 Hz, 16 Amps 82 C (180 F) No 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg) 4420321 Undercounter 208/230 volts, 50/60 Hz, 12 Amps 93 C (199 F) No 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg) 4420330 Undercounter 115 volts, 60 Hz, 16 Amps 82 C (180 F) Yes 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg) 4420331 Undercounter 208/230 volts, 50/60 Hz, 12 Amps 93 C (199 F) Yes 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg) 4420420 Freestanding 115 volts, 60 Hz, 16 Amps 82 C (180 F) No 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg) 4420421 Freestanding 208/230 volts, 50/60 Hz, 12 Amps 93 C (199 F) No 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg) 4420430 Freestanding 115 volts, 60 Hz, 16 Amps 82 C (180 F) Yes 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg) 4420431 Freestanding 208/230 volts, 50/60 Hz, 12 Amps 93 C (199 F) Yes 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg)
General Features SteamScrubber Laboratory Glassware Washers Patent-pending design Upper and lower racks, of Type 304 stainless steel. Upper rack has additional wash arm and side release latches for easy lift out. Racks accommodate a variety of inserts for holding beakers, culture tubes and other specialty glassware (inserts sold separately). See pages 6-7. Water temperature reaches 82 C (180 F) on 115 olt models and 93 C (199 F) on 230 olt models to sanitize glassware and for enhanced washing and faster drying LCD information center for customizing cycles and monitoring operation, including internal water temperature ( C or F) Water recirculation rates of 96 gal/min (363 liters/min) when operated on 115 olt, 60 Hz and 230 olt, 50 Hz and 112 gal/min (424 liters/min) on 230 olt, 60 Hz for thorough cleaning Dual pumps, one for washing and one for draining, to reduce potential for cross contamination Built-in purified water pump to bring non-pressurized or pressurized purified water into the tank for up to six pure water rinses Built-in steam generator that produces hot vapor to penetrate and remove dried residue for cleaner glassware Manual-fill detergent dispenser for powder or liquid detergent Manual-fill rinse aid solution dispenser Built-in forced air drying up to 99 minutes and programmable from 38-70 C (100-158 F) Factory-set cycle programs. All 115 volt models have seven programs: RINSE ONLY, PLASTIC, GLASS, GLASS PLUS, SCIENTIFIC, SCIENTIFIC PLUS, and DRY ONLY. All 230 olt models have three additional programs for a total of ten: INTENSE, INTENSE PLUS and EXTREME. Alarms with display for HOT GLASS, PLEASE WAIT, WATER LOW, WATER HIGH and OERFLOW Two user-set cycle programs User-set delayed start (up to 8 hours) Type 304, brushed stainless steel door, tank, upper and lower wash arms. Freestanding models also have stainless steel exterior sides and top. One-piece, stainless steel, fine mesh particle drain filter to trap debris in tank to protect the pumps No center water distribution tower allowing for greater glassware capacity Four leveling feet 3/8" Female NPT inlet fitting for hot tap water connection Factory-installed drain hose and band clamp SteamScrubber Laboratory Glassware Washer 4400430 shown with 48-Pin Insert 4591601, Petri Dish Insert 4589701, Bulk Tube Insert 4542100, Utensil Holder 4542500 and BOD Bottle Insert 4589201. Two year warranty on parts and labor Made in the U.S.A. IQ/OQ available on line. Contact Labconco about on-site validation service (sold separately). More versatility. Accommodate optional Upper and Lower Spindle Racks (without forced air drying through the spindles). See page 6. Requirements Minimum inlet water temperature 49 C (120 F) Recommended inlet water temperature 60 C (140 F) Minimum purified water pressure 0 psi Water consumption per fill 3.4 gallons (13 liters) Hot tap water pressure at the washer 20-120 psi Hot tap water flow rate 1.25 gallons (4.7 liters) per minute 3/8" OD copper tubing for connection to the water inlet valve Purified water with supply piping minimum 3/8" ID to permit at least 0.9 gallon (3.4 liters) per minute flow Exclusive Labconco feature Catalog # Style Electrical Maximum Internal iewing Window Overall Dimensions Shipping Requirements Water Temperature and Light with Door Closed Weight 4400320 Undercounter 115 volts, 60 Hz, 16 Amps 82 C (180 F) No 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg) 4400321 Undercounter 208/230 volts, 50/60 Hz, 12 Amps 93 C (199 F) No 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg) 4400330 Undercounter 115 volts, 60 Hz, 16 Amps 82 C (180 F) Yes 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg) 4400331 Undercounter 208/230 volts, 50/60 Hz, 12 Amps 93 C (199 F) Yes 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg) 4400420 Freestanding 115 volts, 60 Hz, 16 Amps 82 C (180 F) No 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg) 4400421 Freestanding 208/230 volts, 50/60 Hz, 12 Amps 93 C (199 F) No 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg) 4400430 Freestanding 115 volts, 60 Hz, 16 Amps 82 C (180 F) Yes 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg) 4400431 Freestanding 208/230 volts, 50/60 Hz, 12 Amps 93 C (199 F) Yes 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg) 3
General Features FlaskScrubber antage Series Laboratory Glassware Washers Patent-pending design Lower spindle rack, of Type 304 stainless steel, with 36 detachable large spindles for washing narrow-neck glassware. Eighteen glassware holders, 36 clips and 10 additional interchangeable small spindles are included. Rack accommodates a variety of inserts for holding beakers, culture tubes and other specialty glassware (inserts sold separately). See pages 6-7. Water temperature reaches 93 C (199 F) to sanitize glassware and for enhanced washing and faster drying LCD information center for customizing cycles and monitoring operation, including internal water temperature ( C or F) Water recirculation rates of 96 gal/min (363 liters/min) when operated on 230 olt, 50 Hz models and 112 gal/min (424 liters/min) on 230 olt, 60 Hz for thorough cleaning Dual pumps, one for washing and one for draining, to reduce potential for cross contamination Built-in purified water pump to bring non-pressurized or pressurized purified water into the tank for up to six pure water rinses Built-in steam generator that produces hot vapor to penetrate and remove dried residue for cleaner glassware Water conductivity monitor to confirm rinse water cleanliness and effective detergent removal RS-232 port for monitoring washer operation on a user-supplied computer or recorder Automatic liquid detergent dispenser with peristaltic pump Automatic rinse aid dispenser Manual-fill detergent dispenser for powder or liquid detergent Manual-fill rinse solution dispenser Built-in, HEPA-filtered forced air drying through the spindles up to 99 minutes and programmable from 38-70 C (100-158 F). HEPA filter is 99.97% efficient on particulates 0.3 micron. Ten factory-set cycle programs: RINSE ONLY, PLASTIC, GLASS, GLASS PLUS, SCIENTIFIC, SCIENTIFIC PLUS, INTENSE, INTENSE PLUS, EXTREME, and DRY ONLY Alarms with display for HOT GLASS, PLEASE WAIT, WATER LOW, WATER HIGH, OERFLOW, LIQUID DETERGENT and RINSE AID Two user-set cycle programs User-set delayed start (up to 8 hours) Type 304, brushed stainless steel door, tank, upper and lower wash arms. Freestanding models also have stainless steel exterior sides and top. Clear tempered safety glass viewing window 25-watt interior light One-piece, stainless steel, fine mesh particle drain filter to trap debris in tank to protect the pumps No center water distribution tower allowing for greater glassware capacity Four leveling feet FlaskScrubber antage Series Laboratory Glassware Washer 4540031 3/8" IPS inlet fitting for hot tap water connection Factory-installed drain hose and band clamp Two year warranty on parts and labor Made in the U.S.A. IQ/OQ available on line. Contact Labconco about on-site validation service (sold separately). Accommodate optional Upper Spindle Rack with additional wash arm and side release latches. See page 6. More versatility. Accommodate optional SteamScrubber Upper and Lower Racks. See page 6. Requirements Minimum inlet water temperature 49 C (120 F) Recommended inlet water temperature 60 C (140 F) Minimum purified water pressure 0 psi Water consumption per fill 3.4 gallons (13 liters) Hot tap water pressure at the washer 20-120 psi Hot tap water flow rate 1.25 gallons (4.7 liters) per minute 3/8" OD copper tubing for connection to the water inlet valve Purified water with supply piping minimum 3/8" ID to permit at least 0.9 gallon (3.4 liters) per minute flow Exclusive Labconco feature Catalog # Style Electrical Maximum Internal iewing Window Overall Dimensions Shipping Requirements Water Temperature and Light with Door Closed Weight 4 4540031 Freestanding* 208/230 volts, 50/60 Hz, 12 Amp 93 C (199 F) Yes 32.2" w x 27.5" d x 34.2-36.2" h 260 lbs. (118 kg) * Convertible to undercounter
Dimensional Data 24.1" (61.2 cm) Undercounter FlaskScrubber & SteamScrubber 49.6" (126.0 cm) 27.4" (69.6 cm) 36.1" MAX (91.7 cm) 34.1" MIN (86.6 cm) 24.2" (61.6 cm) Freestanding FlaskScrubber & SteamScrubber 49.7" (126.2 cm) 27.5" (69.8 cm) 36.2" MAX (91.9 cm) 34.2" MIN (86.9 cm) 32.2" (81.7 cm) FlaskScrubber antage Series* 49.7" (126.2 cm) 27.5" (69.8 cm) 36.2" MAX (91.9 cm) 34.2" MIN (86.9 cm) FRONT *Freestanding model may be converted to undercounter SIDE 5
Accessories 6 Guide to Accessories Use the icon key below to select accessories that fit your washer. Racks can accommodate a maximum of two inserts except Utensil Holders and Utensil Baskets; racks can hold a maximum of five Utensil Holders* or four Utensil Baskets. For use in SteamScrubber For use in FlaskScrubber For use in FlaskScrubber antage Series Fits in Upper Standard Rack Fits in Lower Standard Rack Fits in Lower Spindle Rack with spindles removed and plugged Fits in Upper Spindle Rack with spindles removed and plugged Base Stands Elevate washers 17" (43.2 cm) for washer loading convenience and storage of supplies. Type 304 stainless steel stationary stand, fully assembled with leveling feet and instructions. Upper Spindle Racks Constructed of Type 304 stainless steel. Include side release latches, 30 removable spindles, 30 adjustable height clips, 10 small spindles, 15 plastic glassware holders, tool to remove spindles, 30 nylon plugs, and wash arm. Spindles may be removed and plugged to accommodate accessory inserts (sold separately). Spindle dimensions: 5.25" high x 1/4"OD. Overall dimensions: 20.0" w x 20.9" d x 7.2" high (51 x 53 x 18 cm). Accommodate glassware up to 8.5" high. 4595400 Stand for Freestanding FlaskScrubbers or 80 lbs. (36 kg) SteamScrubbers, 24.2" w x 27.5" d x 17.0" h (61 x 70 x 43 cm), includes one storage compartment with hinged door 4595500 Stand for FlaskScrubber antage Series, 105 lbs. (48 kg) 32.2" w x 27.5" d x 17.0" h (82 x 70 x 43 cm), includes two storage compartments with hinged doors 4595600 Upper Spindle Rack for FlaskScrubber and 20 lbs. (9 kg) FlaskScrubber antage Series Glassware Washers. Includes side rails for tank side wall installation. Provides direct injection cleaning and forced air drying through the spindles. 4595800 Upper Spindle Rack for SteamScrubber 16 lbs. (7 kg) Glassware Washers. Provides direct injection cleaning through the spindles. Lower Spindle Rack 4595700 One is included with every FlaskScrubber and FlaskScrubber antage Series Glassware Washer. May be used in place of the Lower Standard Rack in any SteamScrubber. Constructed of Type 304 stainless steel. Includes 36 removable spindles, 36 adjustable height clips, 10 small spindles, 18 plastic glassware holders, tool to remove spindles and 36 nylon plugs. Spindles may be removed and plugged to accommodate accessory inserts (sold separately). Spindle dimensions: 7.4" high x 1/4"OD. Overall dimensions: 21.1" w x 21.0" d x 8.6" high (54 x 53 x 22 cm). Accommodate glassware up to 9.8" high (without upper rack in place). Accommodate glassware up to 4.8" high (with upper rack in place). Shipping weight 20 lbs. (9 kg). Upper Standard Racks One rack is included with every SteamScrubber. May be used in any FlaskScrubber or FlaskScrubber antage Series. Constructed of Type 304 stainless steel. Include side release latches and wash arm. Add accessory inserts below and on pages 7 and 8 to suit your glassware mix (sold separately). Dimensions: 20.2" w x 20.9" d x 6.0" h (51 x 53 x 15 cm). 4595900 Upper Standard Rack for FlaskScrubber and 16 lbs. (7 kg) FlaskScrubber antage Series Glassware Washers. Includes side rails for tank side wall installation. 4587000 Upper Standard Rack for SteamScrubber 12 lbs. (5 kg) Glassware Washers Lower Standard Rack 4588500 One is included with every SteamScrubber. May be used in any FlaskScrubber or FlaskScrubber antage Series. Constructed of Type 304 stainless steel. Add accessory inserts below and on pages 7 and 8 to suit your glassware mix (sold separately). Dimensions: 21.1" w x 21.0" d x 3.5" h (54 x 53 x 9 cm). Shipping weight 10 lbs. (5 kg). * Four Utensil Holders maximum in FlaskScrubber and FlaskScrubber antage Series Washers. Utensil Holder 4542500 For spatulas, spoons, scoops and other miscellaneous utensils. Utensils fit vertically in four compartments, 2.75" w x 3.5" d x 4.9" h (7 x 9 x 12 cm). Type 304 stainless steel. Dimensions: 10.8" w x 4.1" d x 6.6" h (27 x 11 x 17 cm). Shipping weight 4 lbs. (2 kg). Utensil Basket 4402201 For miscellaneous labware such as stoppers, spatulas and other small lightweight items that will not pass through No. 4 mesh sides and bottom. Retainer top is required and included. Type 304 stainless steel. Dimensions: 8.0" w x 8.0" d x 4.0" h (20 x 20 x 10 cm). Shipping weight 2 lbs. (1 kg).
Accessories Bulk Tube Insert 4542100 Quick loading. For vertically-positioned test tubes. Holds up to 600 each 13 mm tubes or 244 each 20 mm tubes. Bottom, grate size 0.38" (9.5 mm), allows water to drain from inverted tubes. When insert is less than fully loaded, the divider may be adjusted to keep tubes upright. Type 304 stainless steel. Smallest divided compartment size: 1.8" w x 8.1" d x 4.2" h (4 x 21 x 11 cm). Overall interior dimensions (without divider): 18.7" w x 8.1" d x 4.2" h (48 x 21 x 11 cm). Dimensions: 21" w x 8.3" d x 4.4" h (53 x 21 x 11 cm) Shipping weight 5 lbs. (2 kg). Culture Tube Inserts Choose from three inserts designed to hold tubes from 10 to 24 mm OD. Type 304 stainless steel. 48-Pin Insert 4591601 Forty-eight pins accommodate a variety of labware. Type 304 stainless steel. Stainless steel pins have plastic tips to protect glassware from scratching. Dimensions: 7.8" w x 19.3" d x 5.2" h (20 x 49 x 13 cm). Shipping weight 2 lbs. (1 kg). Petri Dish Insert 4589701 For petri dishes, watch glasses and microtiter plates. Capacity: 24 plates. Grid size: 22 mm x 140 mm. Type 304 stainless steel. Dimensions: 19.2" w x 8.6" d x 5.9" h (49 x 22 x 15 cm). Shipping weight 2 lbs. (1 kg). Catalog # Description Dimensions Grid Size Shipping Wt. 4588600* 242 tubes, 18.0" w x 8.6" d x 4.5" h 16.8 mm x 4 lbs. 10 mm to 12 mm (46 x 22 x 11 cm) 16.8 mm (2 kg) 4402001 144 tubes, 18.0" w x 7.8" d x 6.4" h 23.8 mm x 3 lbs. 15 mm to 18 mm (46 x 20 x 16 cm) 23.8 mm (1 kg) 4402101 105 tubes, 18.0" w x 8.3" d x 9.9" h 26.5 mm x 3 lbs. 20 mm to 24 mm (46 x 21 x 25 cm) 26.5 mm (1 kg) 4401401 Retainer 18.5" w x 8.3" d x 0.3" h 2 lbs. Top (47 x 21 x 1 cm) (1 kg) * Includes 4401401 Retainer Top Labware Inserts Pins hold a variety of wider-mouth flasks, beakers and other labware in inverted position. Retainer Top is recommended for use with plastic and lightweight glassware. Inserts and Retainer Top of Type 304 stainless steel. Stainless steel pins have plastic tips to protect glassware from scratching. DNA Sequencing Plate Insert 4591500 For electrophoresis plates, 10" x 16.6". Capacity: 6 plates. Type 304 stainless steel with plastic glides. Dimensions: 17.1" w x 8.5" d x 9.9" h (43 x 22 x 25 cm). Shipping weight 6 lbs. (3 kg). Tray Insert 4598401 For pans, instrument trays, multipurpose trays and other shallow containers. Capacity: 5 trays. Type 304 stainless steel. Dimensions: 18.2" w x 12.2" d x 9.1" h (46 x 31 x 23 cm). Shipping weight 2 lbs. (1 kg). Catalog # Description Dimensions Shipping Wt. 4401501 10-Pin Insert 19.3" w x 8.8" d x 8.0" h 3 lbs. (1 kg) (49 x 22 x 20 cm) 4401801 32-Pin Insert 19.3" w x 8.8" d x 6.0" h 3 lbs. (1 kg) (49 x 22 x 20 cm) 4401901 Retainer Top 18.5" w x 8.0" d x 0.3" h 2 lbs. (1 kg) (47 x 20 x 1 cm) BOD Bottle Insert 4589201 Type 304 stainless steel. Capacity: 18 bottles. Grid size: 70 mm x 70 mm. Dimensions: 19.5" w x 8.8" d x 6.0" h (49.5 x 22.2 x 15.2 cm). Shipping weight 2.0 lbs. (0.9 kg). Pipet Inserts Permit direct injection cleaning of pipets. Self-sealing silicone check valves allow washing of partial or full loads. Type 304 stainless steel. FlaskScrubber and FlaskScrubber antage Series Washers hold up to four 4492000 or two 4595200 Inserts. 4494200 Holds 8 pipets, 1 ml to 10 ml. Includes one 1.25" mounting spindle. 2 lbs. (1 kg) Includes 1.25" mounting spindle. 4595200 Holds 16 pipets, 1 ml to 50 ml. Includes two 1.25" mounting 3 lbs. (1 kg) spindles and PC-coated holder. 7
Accessories and Consumable Products Glassware Holders Grip glassware over spindles. *Eighteen 4585204 Glassware Holders are included with every FlaskScrubber and FlaskScrubber antage Series Glassware Washer. 4424600 4.0" h (10 cm) vinyl-coated 0.4 lb. (0.2 kg) Type 304 stainless steel wire with height adjustment screw 4424800 6.0" h (15 cm) vinyl-coated 0.4 lb. (0.2 kg) Type 304 stainless steel wire with height adjustment screw 4585204* 3.9" h (10 cm) plastic 0.4 lb. (0.2 kg) with Type 304 stainless steel height adjustment clip Small Spindles with Clips 4596000 Included with every FlaskScrubber and FlaskScrubber antage Series Glassware Washer. Type 304 stainless steel. Spindles may be used in any spindle location on any Upper or Lower Spindle Rack to provide direct injection cleaning of small narrow neck glassware. Each spindle is 4.3" h x.12" OD. Package of 10 spindles with 10 height adjustment clips. Shipping weight 3 lbs. (1 kg). Freestanding-to-Mobile Conversion Kits Add mobility to freestanding SteamScrubber and FlaskScrubber Glassware Washers. Allow washers to be plugged into a 20 amp electrical wall outlet and connected to a standard laboratory sink faucet. Include four 2-inch diameter rubber casters, two aerator adapters for connection to standard 55/64"-27 male and 15/16"-27 female laboratory faucets, drain hose and installation instructions. Not for use with undercounter washers or FlaskScrubber antage Series Glassware Washers. 4596100 Mobile Conversion Kit, for 115 volt operation. 60 lbs. (27 kg) Includes 10' power cord with NEMA 5/20 plug. 4596101 Mobile Conversion Kit, for 230 volt operation. 60 lbs. (27 kg) Includes 8.2' power cord with NEMA 6/20 plug. Liquid Detergent Dispenser Kit 4587500 Connects to any SteamScrubber or FlaskScrubber Glassware Washer during installation to automate liquid detergent dispensing. Includes peristaltic pump, float switch, tubing, one gallon plastic container and installation instructions. Detergent is not included. Not for use with FlaskScrubber antage Series Glassware Washers. Shipping weight 10 lbs. (5 kg). Drain Water Cooling Kits Provide plumbing components, solenoid valve and electrical connections necessary to mix cold tap water with hot drain water so that water <60 C (<140 F) is directed to the house drain system. When the washer s drainage pump is activated, the solenoid valve opens releasing the flow of cold tap water to the drain. 4591900 Cold Water Drain Kit, 115 volt, 60 Hz operation 8 lbs. (4 kg) 4591901 Cold Water Drain Kit, 230 volt, 50/60 Hz operation 8 lbs. (4 kg) 2007 by Labconco Corporation. Printed in the U.S.A. Product design subject to change without notice. LabSolutions Liquid Detergent 4522000, Neutralizing Acid Rinse 4522000, and Powder Detergent 4422100 and 4422000 LabSolutions Non-Foaming Powder Detergent Specially formulated for Labconco glassware washers. Removes most lab contaminants such as grease, agar, blood and protein digestates. Rinses completely. Non-foaming formula does not promote leaks. A 1% solution has a ph of approximately 12.5. Contains phosphates. Non-hazardous formula may be shipped anywhere. Catalog# Description Shipping Wt. 4422000 Powder Detergent, small pail for approximately 140 loads 10 lbs. (5 kg) 4422100 Powder Detergent, large pail for approximately 400 loads 28 lbs. (13 kg) LabSolutions Low-Foaming Liquid Detergent Specially formulated for Labconco glassware washers. Removes a wide range of laboratory contaminants. Rinses completely. Non-corrosive formula won t degrade stainless steel, glass or plastic. Phosphate-free for environmentally-safe disposal. Chlorine-free and tissue culture-safe. May be used in hot or cold water. Catalog# Description Shipping Wt. 4522000 Low-Foaming Liquid Detergent for approximately 180 loads 12 lbs. (5 kg) 1 gallon (3.8 liters) LabSolutions Neutralizing Acid Rinse Specially formulated for rinse aid reservoir in Labconco glassware washers. Mild acid corrects ph reducing alkaline detergent residue. Removes hard water deposits, mineral deposits, accumulated lime scale that can cloud glassware. Rinses completely. Catalog# Description Shipping Wt. 4522200 Neutralizing Acid Rinse, fills reservoir approximately 6 times 3 lbs. (1 kg) 34 ounces (1 liter) For MSDS information, visit our website at www.labconco.com or call customer service at 800-821-5525 or 816-333-8811. Labconco Corporation 8811 Prospect Avenue Kansas City, MO 64132-2696 Telephone: 800-821-5525 or 816-333-8811 FAX: 816-363-0130 E-MAIL: labconco@labconco.com HOME PAGE: www.labconco.com 2-10-8/07-Graphx-7.5M-R1