WASHING MACHINE SWES(P)/XST SERVICE Manual WASHING MACHINE CONTENTS! Caution for the safety during servicing. Product Features. Technical Points 3. Schematic and Circuit and PCB Pattern Diagram 4. Cautions in Servicing 5. Troubleshooting 6. How to Disassemble 7. Exploded Views & Part List 8. Product Specifications
! Caution for the safety during servicing. Do not allow the customer to repair the product. The person may be injured or the product life may be shortened.. Execute A/S after unplugging the power supply unit. Be care of the electric shock. 3. Do not plug several plugs in the same outlet. It may cause the fire due to overheat. 4. Check the damage, pressing or burning of the power plug or outlet. Replace it promptly if it has problem.(it may cause the electric shock or fire) 5. Do not clean the main body with the water. It may cause the electric shock and fire and shorten the product life) 6. The wiring of the harness shall be free from the moisture and tightened during serving. It shall not be deviated by certain impact. 7. Remove any dust or filth on the housing section,wiring section,connection section during servicing. Protect the cause of the fire such as the tracking,shortage and etc. 8. Check any mark of the moisture on the electrical parts, harness section and etc. Replace the parts or remove the moisture. 9. Check the assembly status of the parts after servicing. Maintain the status before servicing. 0. Pull out the power cord with holding the plug. Be care of the electric shock and fire when the cord is damaged.. Unplug the power plug from the outlet when the wash machine is not used. Be care of the electric shock and fire due to the strike of the lightening.. Do not use or store the spray or flammable materials(including gasoline,alcohol and etc.) around the wash machine. Be care of the explosion or fire due to the electric spark. 3. Do not put the bowl of water or wet laundry on the wash machine. If the water is penetrated to the wash machine, this may cause the electric shock or fire. 4. Do not install the wash machine in the place where the snow or rain falls. It may cause the electric shock and fire and shorten the product life. 5. Do not push the control buttons with the awl,pin, or sharp materials. It may the electric shock and trouble. 6. Check the wash machine is leveled horizontally and installed properly on the floor. The vibration may shorten the product life. 7. Joint the wire by the connector correctly. When the wire is jointed by the tape, this may cause the fire due to the tracking. 8. When the wash machine is to be laid for the service, put the pad on the floor and lay the product at side slowly. If the wash machine is laid front, the relay may be damaged by the tub. 9. When the wash-heater is replaced, check it is inserted in the bracket-heater and screw the nut. If the wash-heater is not inserted in the bracket-heater properly, this may cause the noise and leakage since it is contacted to the drum.
. Product Features Whirling washing tub * The laundry becomes cleaner than ever since the laundry is turned over in the whirling tub and washed by the beating of the higher whirling embossing on the tub. Washing by the strike of the strong falls * The strong falls vigorously strike the full load of laundry or the large laundry to clean. The light bedding is pressed even for the old dirt to be thoroughly removed. No detergent remnants in the detergent and the softener dispensers. * The powder detergent is solved to the liquid detergent in order to prevent the contamination of the environment. * If the softener is put in the dispenser, it is automatically flushed during the rinsing cycle. Softener Compartment Detergent Compartment Leveling feet * Since the leveling feet are on the front, it is convenient to adjust by hand. Large filtering net * Since the lint or other substances are thoroughly collected by the filtering net that is more than times larger than the existing one, you can feel the difference by the far cleaner laundry. Water spouting washing hands * The water spouting washing hands shoot up the water columns in the water to prevent the laundry from being entangled. The water columns shot up by the water spouting washing hands prevent the laundry from being entangled in substituted for the rod and they wash the laundry by scrubbing, which is the merit of the revolving board washer, as well. As a result, the cleaning ability is also excellent. Wider variety of rinse selection * By adding the rinse selection button, during the rinsing cycle, not only water is supplied, but also water can be added to the higher water level than that of the washing cycle and so on. Consequently, you have more choices to select the rinsing mode. SAMSUNG ELECTRONICS CO., LTD
. Technical Points - Each Key & Display REMAINING TIME/MIN COLD/WATER HOT/WATER HIGH MEDIUM LOW SMALL MINIMUM TIMES TIMES 3 TIMES FUZZY BEDDING WOOL SPIN ONLY RINSE ONLY WATER SUPPLY WATER LEVEL RINSE ADDITION COURSE LEVEL INDICATOR START/PAUSE POWER - Definition of Function for Each Key. Course Key ) Before pressing the initial start key or while in pause, each time this key is pressed, one of the courses is selected in the following order. Fuzzy Bedding Wool Spin Only Rinse Only ) While in operation by the effective selection of the course, the input of this key is ineffective. However, it makes the input sound. 3) When changing the course after a Pause while in operation by the effective input of the Course key, the default value of each cycle in the finally selected course is set even if each cycle (the number of rinsing cycles) has been changed by using the Manual key in the previous course. 4) While in operation by the effective selection of the course, the input of all the keys except the Course key is effective. However, during the spinning cycle, only the Start/Pause key and the Power key are effective. 5) The weight sensor functions only in the Fuzzy course and the Rinse Only course. Each time the Water Level key is pressed, Low Medium High Medium Low Small Minimum Small is selected in order. SAMSUNG WASHING MACHINE
6) Table of Function for Each Course Washing Time Classification Fuzzy Bedding Wool Spin Only Rinse Only High water level 8 min 8 min 6 min x x Medium water level 8 min 8 min 6 min x x Low water level 8 min 8 min 6 min x x Small water level min x 6 min x x Minimum water level,om x x x x Number of Rinsing Cycles Spinning Time Rinse Addition Range -3 times -3 times -3 times -3 times -3 times Default Value times 3 times times x times Default Value 6 min 9 min min 6 min x Default Value of Water Supply Selection Cold water Cold water Cold water x Cold water Water Level Setting Range by Weight Sensor Small- High x x x Small- High Water Current Pattern A B C x D 7) While in operation by the effective course key, the corresponding mode can be updated by the Rinse Addition key input. However, the Rinse Off is skipped. 8) While in the initial stage of Power On (while the Fuzzy course is selected), after switching from the Fuzzy course to another course before the Start key input, the corresponding mode can be updated by the Rinse key input. 9) While the Fuzzy, Bedding, or Wool course is in progress, press the Pause key and then the Rinse Addition key to increase the number of the rinsing cycle. Each time the Rinse Addition key is pressed, one is selected as shown below. (before entering the rinsing cycle) E.g.) Fuzzy course One time Two times Three times Off 0) When the Fuzzy, Bedding, or Wool course is selected, the cycles are fully automatically proceeded. ) When the Spin Only is selected, the Spin Only mode is carried out and the Rinse Addition key can be input. (before the Start key input) ) When the Rinse Only is selected, the Rinse Only mode is carried out. Each time the Rinse Addition key is pressed, one is selected as follows. (before entering the rinsing cycle) One time Two times Three times Off 3) On starting the selected course, the LED indicating the corresponding course is ON/OFF at sec interval. While in Pause, the LED is ON. * ) The LED for the Water Supply and Water Level are ON/OFF at sec interval. When supplying water is done, it is kept ON. ) The LED for the Rinse Addition is ON until the rinsing is done. SAMSUNG ELECTRONICS CO., LTD 3
. Rinse Addition Key ) The input of this key is always effective except while in progress of the intermittent spin, the spin, or the pause mode. ) After selecting the Rinse Only and before inputting the Start key, one is selected by touching this key as follows. One time Two times Three times Off (Same in the initial stage of Power On) 3) While in progress of the Rinse Only mode, if the Course key is pressed, only the key input sound is produced. 4) While in progress of the Rinse Only mode, if the Pause key is pressed and then the Course key is input, the Rinse Only mode is cancelled to switch to the selected mode. 5) When the number of the rinsing cycles is changed, one previously carried out is canceled and the finally selected one is applied. 6) While in operation or after a pause, this key can be input until the final rinse is done just before the draining cycle starts. 3. Water Supply Key ) The input of this key is always effective except in the Error mode. ) Each time this key is pressed, one is selected in the following order. Cold water Hot & Cold water Hot water 3) When the water supply selection is changed by inputting this key, the selected water supply maintains even if the course is changed. When changed to the Wool course, automatically cold water is selected. However, when changed to another course again, the previous water supply selection is applied again. 4) The Error in Paragraph ) is as follows. () Water Supply Error () Draining Error 5) While in supplying water, the lamp for the corresponding water supply flashes in the way of sec ON/OFF. 4 SAMSUNG WASHING MACHINE
4. Start/Pause ) Each time this key is input, one is selected in the following order. Start Pause ) This key carries out the Error canceling function. () Water Supply Error () Draining Error 3) When restarting after a pause, the delay time of the drive part is as follows. Operation Mode Drive Part Operation Mode Pause Mode Operation Mode Remarks Water Supply Mode Water supply valve Rinse valve sec The delay time when carrying out the canceling function by the UNB sensor is 0 sec. Washing Mode Motor MR. ML sec Draining/Stop Draining Motor 4 sec Spin Mode (including Intermittent Spin) Draining Motor Motor (ML) 0 sec 0 sec 5. Water Level Key ) The input of this key is always effective except in the Error mode. Error: Water Level Sensor, Water Supply Error, Draining Error ) Each time this key is input, one is selected in the following order. Low Medium High Medium Low Small Minimum Small 3) When the Bedding course is selected, only the low water level or higher can be selected. 4) When the Wool course is selected, only the small water level or higher can be selected. 5) While a water level is selected, if the course is changed to the Wool or Bedding course after a pause, in case of the Bedding course, if the previous water level is below the Low, the water level is automatically set to the High, however, if the previous water level is the Low or higher, the previous water level is applied. In case of the Wool course, if the previous water level is below the Small, automatically the high water level is set. However, if the previous water level is the Small or higher, the previous water level is applied. 6) After supplying water is done just before the motor runs, if the water level is changed by touching the water level key, the remaining time is recalculated since the water supplying time for the corresponding water level is changed. 7) Changing washing time according to the water level in the Fuzzy course is applied only before the motor starts to run. After the motor starts to run, washing is proceeded according to the washing time for the previous water level regardless of the water level change. 8) While is displayed as the initial data in the Fuzzy course, by inputting the water level key, the remaining time for the corresponding water level immediately appears. However, if the Start key is input in the initial stage of the Fuzzy without inputting the water level key, is displayed until the weight sensing is done. SAMSUNG ELECTRONICS CO., LTD 5
-3 Main Functions -3- Washing Cycle. Water Supply Mode ) In the water supply mode of each cycle, the valve for the corresponding water supply is on according to the water supply selection until the selected water level is reached. ) The water level selection is as follows. (Unit: water amount-l, Frequency: KHz) Reset Minimum Small Low Medium High 5.0 3.76 3..75..9 3) The selection of the water supply valve-on for each cycle according to the water supply stated in Paragraph ) is as follows. Water Supply Selection Washing Rinsing Rinsing, 3 Added Water Cold water Cold water Cold water Cold water Hot, Cold water Hot, Cold water Hot, Cold water Cold water Hot water Hot water Hot, Cold water Cold water Following the water supply selection for each of Washing, Rinsing, Rinsing /3 Note). When only the hot water is selected, for the initial 0 sec of supplying water at the beginning of washing, the cold water valve is on. To avoid the damage of the cloth and to solve the detergent completely. While in rinsing, the water supply selection is applied only to the Rinsing as shown in the table above. In the Rinsing or later, only cold water is supplied. 4) While supplying water, the corresponding lamp is ON/OFF at sec interval. When the water supply is done, the corresponding lamp is on. 5) When supplying water is not done after the standard time allotted for supplying water is over, the remaining time does not decrease. 6) When supplying water is done before the standard time allotted for supplying water is not over, the remaining time is compelled to decrease according to the allotted time and then the next cycle starts. 7) When supplying water is not done 60 min later after starting the water supply, the Water Supply Error mode is carried out. (including the water supply or the additional water supply for clearing the unbalance) 8) After supplying water is done, if the water level key is input and the selected level is higher than the previous one, water is supplied to the selected level. Meanwhile, the motor is off and the remaining time is not reduced while in supplying water. 9) Table of Water Supply Time for Each Water Level Water Level High Medium Low Small Minimum Remarks Water Supply Time 5 min 4 min 30 sec 4 min min 30 sec min 30 sec 0) While in operation, if the water level drops below the reset, water is supplied to the selected water level and then the operation proceeds. ) When the water level reaches the one that is one level lower than the selected level while in supplying water, the motor starts to run with the default water current pattern. When the selected water level + 00 Hz are reached, the motor is off. (excluding the small water level or lower) *. Motor running time out 30 sec. This procedure is carried out in washing or rinsing as well. 6 SAMSUNG WASHING MACHINE
. Washing Mode ) After reading the selected water level and washing is carried out for min or 9 min, the motor is off for 3 sec to read the frequency of the water level. If the water level is lower than the selected water level, water is added to the selected water level and then washing proceeds. The time for adding water does not exceed 30 sec. * While in rinsing, water is added min later after the rinsing cycle starts. ) Table of Water Current Pattern during the washing cycle of each water level for each course according to the washing selection (see the appendix) 3) For each course or each water level, the water addition mode is carried out min or 9 min after the washing cycle starts and min after the rinsing cycle starts. The time out is 30 sec. Although the washing time is changed by the washing-adjusting key while in washing cycle after the water addition mode, the water addition mode is not carried out. 4) In case that the water addition mode is carried out twice in a course, even though the time for any cycle is changed, no more water addition mode is carried out. 5) When the washing time is changed after the water addition mode is carried out once, it is carried out once more within the changed washing time. -3- Rinsing Cycle. Draining Mode ) The draining valve is kept ON. If the water level at the initial stage of this mode is higher than the reset, the delay mode is carried out for 50 sec after reading the reset. If lower than the reset, it is carried out for 0 sec. ) The remaining time decreases while the draining mode is carried out until the standard time for draining is over. After that, the remaining time does not decrease any longer. When this mode is done, the standard time for draining is considered to be over. Water Level High Medium Low Small Minimum Remarks Draining Time min 0 sec min min 50 sec min 30 sec min 0 sec Excluding 50 sec delay 3) When the water level is higher than the reset in 5 min after starting the draining mode, the draining error mode is carried out. The buzzer sounds 5 times and the pause mode is carried out. 4) If the Start key is input during the step 3), the error is cleared, the time out is set to 5 min again, and then draining begins.. Intermittent Spin Mode ) If the door is open while in this mode, this mode is paused and the door open alarm (5 times of the door open melody) sounds. ) If the door is closed while the door open alarm sounds, the alarm stops and the operation proceeds in the same way when the Start/Pause key is input. 3) When the safety S/W detects the unbalance while in this mode, the unbalance clearing mode is carried out. Unbalance detecting mode - Checker S/W detecting time: 0 ñ 449 ms - When the door is open (Reed S/W detecting), the drive part is turned off immediately after 0 ms is detected. When the door is closed while the door open alarm sounds, the alarm mode is canceled, the draining valve is on in 0 sec after it is off, and then the motor restarts after the draining valve is on. ➁ Unbalance clearing mode - When the unbalance occurs while in spinning after the washing cycle ends, this mode is carried out in the same way when one rinsing cycle is added. When the unbalance is detected while in rinsing, water is supplied and then the next rinsing step is proceeded. When the unbalance occurs during the final spin, the clearing mode is carried out up to twice. At the third time, the unbalance alarm sounds. - At the beginning of the clearing mode, the standard time for supplying water + min is added to the initial remaining time of the corresponding cycle. The clearing mode is carried out with the disentangling water current for min after supplying water. - When the unbalance error occurs, UE flashes in the way of sec ON/OFF and the error melody sounds 5 times. - When the unbalance occurs while in the spin only mode, the error alarm sounds. SAMSUNG ELECTRONICS CO., LTD 7
3. Spin Mode ) This mode is carried out by turning the washing motor counterclockwise. The draining valve is kept on during the corresponding spinning time. ) The other functions are the same as those of the intermittent spin mode. 3) The spinning time after washing or rinsing, or the final spinning time is shown in the time chart. 4. Pause Mode ) This mode is carried out by turning off ML for min 30 sec and keeping the draining valve on. ) When the door is open while in the pause mode of the rinsing cycle, the door open error occurs. When the door is closed again, the restart mode is carried out. 3) When the door is open while in the pause mode of the final spinning cycle, the ending mode is carried out. 5. Draining Mode ) The same as the draining mode of the washing cycle. 6. Rinsing Mode ) When the selected water supply is done, rinsing starts according to the water level. ) The rinsing time is min 30 sec regardless of the number of rinsing cycles. However, in the Wool course, it is min. 3) Table of Water Current Pattern during the rinsing cycle of each water level for each course (see the appendix) -3-3 Spinning Cycle ) The same as the intermittent spin mode or the spin mode of the rinsing cycle. ) In the Wool course, spinning is carried out by 0-sec ON and 5-sec OFF. -3-4 Ending Cycle ) This mode is carried out when all the selected cycles are done. ) While in this mode, the end melody sounds and all the drive parts are off. Meanwhile, 00 is displayed by -sec ON/-sec OFF. 3) When this mode ends, the automatic power relay off is carried out. 8 SAMSUNG WASHING MACHINE
-4 Definition of Special Mode -4- Error Occurrence Mode. Water Level Sensor Error ) When the water level sensor detects the frequency of below 5 KHz or above 30 KHz for 5 sec or longer, the water level sensor error occurs. ) Display: E, 0.5 sec ON/OFF 3) How to clear: Power key-on. Power Relay Failure ) When the power is not turned off by the automatic power off mode (This mode works only in the test mode.) ) The error melody sounds 5 times. 3) Display: E, 0.5 sec ON/OFF 4) How to clear: : Power key-on 3. Water Supply Error ) When the selected water level is not reached in 60 min after supplying water begins ) The error melody sounds 5 times. 3) Display: 4E, 0.5 sec ON/OFF 4) How to clear: Inputting the Start key to start supplying water again 4. Draining Error ) When the water level does not drop below the reset in 5 min after draining begins. ) The error melody sounds 5 times. 3) Display: 5E, 0.5 sec ON/OFF 4) How to clear: Inputting the Start key to start draining again 5. Door Open Error ) When the door is open while in the mode of the intermittent spin or the spin ) The error melody sounds 5 times. 3) Display: de, 0.5 sec ON/OFF 4) How to clear: Closing the door 6. Unbalance Error ) When the unbalance is detected for the third time during a spinning cycle ) The error melody sounds 5 times. 3) Display: UE, 0.5 sec ON/OFF 4) How to clear: Opening and closing the door 7. Motor Failure Error ) When a failure occurs in the primary motor TRAC, the weight sensor circuit, or the motor ) The error melody sounds 5 times. 3) Display: 3E, 0.5 sec ON/OFF 4) How to clear: High water level washing by the Start key input SAMSUNG ELECTRONICS CO., LTD 9
-4- Automatic Power Off Mode ) After the end melody sounds when all the cycles are done, the automatic power relay off is carried out. Meanwhile, 00 is displayed by -sec ON/-sec OFF. -4-3 Softener Flushing Mode ) The valve for flushing the softener is on as shown below. Supplying water ON OFF RINSE ON OFF 0 5 0 5 0 5 0 5 5 ) The softener is flushed at the final rinsing cycle. However, if the number of the rinsing cycles is adjusted to the higher number while in flushing the softener, the valve for flushing softener is off and then water is supplied. 3) When the number of the rinsing cycles is adjusted to the higher number while in flushing the softener, flushing the softener stops. Later when the final rinsing cycle starts, the softener is flushed for the remaining flushing time of the previous rinsing cycle. 4) When the pause mode is carried out while flushing the softener, flushing the softener stops. When restarted, the softener is flushed for the remaining time. -4-4 Sudden Power Failure Mode ) When the voltage is not detected while a cycle is in progress by the Start key input, all the drive parts are off in order to compensate the sudden power failure. The steps of the cycle are paused in the same way when the Pause key is input. In other words, the remaining time and the other steps are paused, but the display does not disappear. ) When the power is restored, the paused cycle proceeds in the same way when the restart key is input. However, the key input sound is not produced. 3) The power failure is detected when 60 Hz INT is not generated for 50 ms or longer. Clearing is carried out immediately after 60 Hz INT is generated for 450 ms. 0 SAMSUNG WASHING MACHINE
-5 Test Program Mode -5- Test Mode (Drive Part, Other Test) ) How to enter: [Rinse Addition + Course + Power S/W ON] ) Initial display after entering: All display 3) Each time the Rinse Addition key is input at the step ), the mode is selected as shown below. 0 0 03 04 05 4) Mode (Drive Part Test) When the Start key is input while 0 is ON on 88-SEG, 0 remains on the display and each drive part is turned -sec ON/OFF to check the condition of the drive part. ➁ The operating procedures are as follows. Cold water (Cold water LED ON) Draining (Spin LED ON) Hot water (Hot water LED ON) MR (Note ) ML (Note Rinse (Rinse LED ON) * Note : L is ON on 8-SEG * Note : r is ON on 8-SEG 5) Mode (Spin Aging) When the Start key is input while 0 is ON on the display, 0 remains on the display and only the spin is proceeded after the delay time of the draining valve. The intermittent spinning operation is carried out only three times in the way of 3.5-sec ON/4.5-sec OFF, 4-sec ON/4-sec OFF, 4-sec ON/4-sec OFF. When the door open error or the unbalance error occurs, it is detected that ERROR appears on the display and the motor is turned off. ➁ The sequential spinning procedures are carried out in the following order. 7-min ON OFF (3 min) ➂ The draining mode is carried out by detecting the water level. 6) Mode 3 (Washing Aging) When the Start key is input while 03 is ON on the display, 03 remains on the display and the washing motor runs until the power is turned off. ➁ The water current pattern follows that of each water level in the Fuzzy course as shown in the table of the water current pattern. ➂ The water level is detected. 7) Mode 4 (Power Relay Off) When the Start key is input while 04 is ON on the display, 04 remains on the display and the power S/W relay is operated up to three times of 0.5-sec ON/OFF. Then if it is not turned off, E is displayed and the error melody sounds 5 times. 8) Mode 5 (Water Level Sensor) 05 appears on the display during the pause. When the Start key is input, the data of the water level frequency is displayed in 4-digit hexadecimal number. 9) When the Rinse Addition key is input while the corresponding mode is carried out by selecting a mode at the step 4), the mode in progress is canceled to enter the mode designated by the Rinse Addition key. If the Start key is pressed at this time, the finally selected mode is carried out. SAMSUNG ELECTRONICS CO., LTD
-6 Table of Cycle Proceedings () Course Fuzzy Bedding Wool Rinse Rinse Rinse 3 Spin Rinse + Spin Water Level High Medium Low Small Min High Medium Low High Medium Low Small High Medium Low Small Min High Medium Low Small Min High Medium Low Small Min High Medium Low Small Min Washing Rinsing Cycle Rinsing Cycle (Unit: min) Water Washing Drain Intermittent Pause Water Rinse Drain Intermittent Spin Pause Water Rinse Supply Spin Supply Spin Supply 5:00 8:00 :0 :00 :30 5:00 :30 :0 :0 :00 :30 5:00 :30 4:30 8:00 :00 :00 :30 4:30 :30 :00 :00 :00 :30 4:30 :30 4:00 8:00 :50 :00 :30 4:00 :30 :50 :00 :00 :30 4:00 :30 :00 :00 :30 :00 :30 :30 :30 :30 :00 00 :30 :30 :30 :00 :00 :0 :00 :30 :00 :30 :0 :00 :00 :30 :00 :30 5:00 8:00 :0 :00 :30 5:00 :30 :0 :00 :00 :30 5:00 :30 4:30 8:00 :00 :00 :30 4:30 :30 :00 :00 :00 :30 4:30 :30 4:00 8:00 :50 :00 :30 4:00 :30 :50 :00 :00 :30 4:00 :30 5:00 6:00 :0 :00 :30 5:00 :00 :0 :00 0:30 :00 5:00 :00 4:30 6:00 :00 :00 :30 4:30 :00 :00 :00 0:30 :30 4:30 :00 4:00 6:00 :50 :00 :30 4:00 :00 :50 :00 0:30 :30 4:00 :00 :30 6:00 :30 :00 :30 :30 :00 :30 :00 0:30 :30 :30 :00 5:00 :30 4:30 :30 4:00 :30 :30 :30 :00 :30 5:00 :30 :0 :00 :00 :30 5:00 :30 4:30 :30 :00 :00 :00 :30 4:30 :30 4:00 :30 :50 :00 :00 :30 4:00 :30 :30 :30 :30 :00 :00 :30 :30 :30 :00 :30 :0 :00 :00 :30 :00 :30 5:00 :30 :0 :00 :00 :30 5:00 :30 4:30 :30 :00 :00 :00 :30 4:30 :30 4:00 :30 :50 :00 :00 :30 4:00 :30 :30 :30 :30 :00 :00 :30 :30 :30 :00 :30 :0 :00 :00 :30 :00 :30 5:00 :30 4:30 :30 4:00 :30 4:00 :30 :30 :30 :00 :30 SAMSUNG WASHING MACHINE
-6 Table of Cycle Proceedings () (Unit: min) Course Water Level Rinsing Cycle Spin Drain Intermittent Spin Pause Water Rinse Drain Intermittent Spin Pause Spin Supply Spin Remaining Time Fuzzy Bedding Wool Rinse Rinse Rinse 3 Spin Rinse + Spin High Medium Low Small Min High Medium Low High Medium Low Small High Medium Low Small Min High Medium Low Small Min High Medium Low Small Min High Medium Low Small Min :0 :00 6:00 :30 6min 00sec :00 :00 6:00 :30 60min 00sec :50 :00 6:00 :30 58min 00sec :30 :00 6:00 :30 46min 30sec :0 :00 6:00 :30 44min 30sec :0 :00 :00 :30 5:00 :30 :00 :00 9:00 :30 79min 0sec :00 :00 :00 :30 4:30 :30 :00 :00 9:00 :30 76min 30sec :50 :00 :00 :30 4:00 :30 :50 :00 9:00 :30 73min 50sec :0 :00 :00 :30 4min 00sec :00 :00 :00 :30 39min 00sec :50 :00 :00 :30 37min 00sec :30 :00 :00 :30 3min 30sec 07min 30sec 07min 00sec 06min 30sec 05min 00sec 04min 30sec min 40sec 0min 30sec 9min 0sec 6min 00sec 4min 50sec :0 :00 :00 :30 5:00 :30 35min 50sec :00 :00 :00 :30 4:30 :30 34min 00sec :50 :00 :00 :30 4:00 :30 3min 0sec :30 :00 :00 :30 :30 :30 7min 00sec :0 :00 :00 :30 :00 :30 5min 0sec :0 :00 6:00 :30 0min 40sec :00 :00 6:00 :30 0min 30sec :50 :00 6:00 :30 0min 0sec :30 :00 6:00 :30 0min 00sec :0 :00 6:00 :30 09min 50sec :0 :00 6:00 :30 8min 0sec :00 :00 6:00 :30 7min 30sec :50 :00 6:00 :30 6min 50sec :30 :00 6:00 :30 5min 00sec :0 :00 6:00 :30 4min 0sec SAMSUNG ELECTRONICS CO., LTD 3
4. Cautions in Servicing 4- Before Servicing ) When laying down the washer on the front side, if the floor is uneven, put a stand on the floor, and then carefully lay down the washer so as not to damage the out-case. ) When separating the top-cover from the out-case, be cautious that the wire bundle connected to the lower part does not touch the sharp edge of the out-case or is not stretched. 3) When separating the top-cover, be cautious not to damage the checker-s/w. 4) Do not drag the washer on the uneven floor, if avoidable. (It may cause to remove the rubber packing. If then, the violent vibration may occur during the spin.) 6 SAMSUNG WASHING MACHINE
4- While in Servicing ) When replacing the suspension-bar ass y, make sure that the front and the rear are not switched each other and that the parts of other models are not mixed. (During the spin, the violent vibration may occur.) Shape Front White White Red Yellow Rear White White White Yellow ) Structure of Ass y-damper & Cautions in Servicing CALLER-SUSPENSION Existing: Albanian or damping grease Servicing: Applying Albanian grease * Area on which damping grease should not be applied (Applying Albanian) Damping grease (sticky) DAMPER CASE AIR SEAL * Grease or other foreign substances should not stick to this area. Caution ) Be cautious not to apply grease on the area where no grease should exist. ) After replacing the damper, apply enough Albanian grease on the caller-suspension part. Since there are few defective dampers among the recently produced ones owing to the thorough management, be cautious when judging the product whether good or not. SAMSUNG ELECTRONICS CO., LTD 7
4-3 After Servicing ) First, select the installing location. Set the direction of the drain hose according to the condition of the place. Keep the washer the minimum 0 cm away from the wall. c. When the adjustment is done, pull the adjusting handle to the front again to fix the leveling feet. Fixing 4) Properly arrange the wire bundle at the bottom so that it is not stretched even if the tub-ass y leans. (If not, it may cause vibration or noise during the spin.) 0cm 0cm ) Level checking Adjust so that the bubble of the level indicator is in the center of the circle. How to adjust the level Bubble Positio Cause Lower front Lower rear Lower left Lower right Adjustment Adjust the leveling feet. Adjust by putting the leveling rubber or a stand at the rear. Adjust the left side by adjusting the leveling feet on the front or putting the leveling rubber at the rear. Adjust by putting the leveling rubber or a stand at the rear. 5) While reassembling the top-cover after being separated, ensure that the air-hose is not caught between the out-case and the top-cover. (It may cause the occurrence of No drain or No water supply error.) Caution * While separating or assembling the top-cover, the powercord wire on the rear side may come out of the top-cover. It may cause the occurrence of a problem caused by nicking of wire while assembling the cover-tc. Therefore, ensure that the wire does not come out of the top-cover before starting assembling. 3) Leveling If not level, adjust the leveling feet so that the washer is level. Be cautious not to put the hand under the leveling feet. (It may cause to hurt the hand.) * If not level, it may cause the severe vibration or a failure. Be sure to be level. a. Pull the adjusting handle of the left, right leveling feet on the front to the front and push them to the left or right. Loosening b. Adjust the washer upward or downward to be level. 8 SAMSUNG WASHING MACHINE
6. How to Disassemble 6- PCB-Ass y Replacement ) Remove the two cover-screws on the control-panel as shown in the figure, and then remove the screws. ) Push the control-panel to the front as shown by the arrow in the figure and pull it upward to separate. 3) Turn over the control-panel ass y and remove the 5 screws on the PCB Ass y. 4) Raise the ass y gently to the direction to which the screws are removed in order to separate the ass y. 5) Separate the connector connected to the Ass y PCB. While separating the control-panel, be cautious not to stretch the wire excessively. While in assembling, ensure that the wire is not caught in the groove of the top-cover. While assembling the PCB, make sure the it is properly fastened by the fastening hook of the control-panel. If not, the selection S/W will not work. Checkpoint after replacing the PCB-Ass y Check that each component works properly. (using the test mode) 0 SAMSUNG WASHING MACHINE
6- Replacement of pressure-sensor, water-valve, checker-ass y, ass y-detergent ) After removing the screws that fasten the top-cover and the cover-t.c. together, gently push the cover-t.c. to the direction of the arrow in the figure to separate it. Remove the 3 screws ( on the rear, on the front) that fasten the top-cover and the out-case together, gently raise the rear side, and push it to the front in order to separate the top-cover and to turn it over. ➁ Before turning over the top-cover, remove the screw that fastens the earth-wire. EARTH-WIRE ) Pressure-sensor After pulling out the terminal of the pressure-sensor lead-wire, widen the hook to remove the sensor. While assembling the pressure-sensor, ensure that the airhose is not kinked and connected properly. SCREW 3) Water-valve Remove the 3 terminals of the water-valve lead-wire. Then remove the 3 screw-taps, TH that fasten the water-valve of the ass y-detergent inside the top-cover to disassemble the ass y water-valve. Before assembling the water-valve, ensure that the sealdetergent is not missing. (If the seal-detergent is missing, water leaking occurs and it may cause the danger of a short.) 4) To disassemble the ass y-detergent, turn over the top-cover and remove the screws. 5) After pulling out the terminal of the checker-s/w lead-wire, remove the screws that fasten the checker-s/w. (Pull out the lead-wire terminal while pressing the hook.) SAMSUNG ELECTRONICS CO., LTD
6-3 Shaft-Ass y Replacement ) Remove the cover-screws (front, rear) on the control-panel by using the (-) driver. After that, remove the screws (front, rear) that fix the control-panel by using the (x) driver. Then push the controlpanel to the front and pull it upward to separate it. ) After removing the screws ( on the rear, on the front) that fix the top-cover and the screw that fixes the earth-wire, raise the rear part of the top-cover ass y and push it to the front to separate it. 3) Remove the 4 screws that fix the cover-tub and take out the covertub. 4) Disassemble the pulsator-cap. Insert the (-) driver between the pulsator-cap + the pulsator-cap and push upward to separate it. When assembling When disassembling Align with the groove of () and press () to assemble. Caution: If the (-) driver is inserted too deeply then pressed, it may cause to damage the hook. Be cautious when using the driver. 5) Loosen the pulsator fixing bolt by using the mm box and remove it. 6) Remove the nut that fixes the ass y-spin basket and the shaft together by using the jig box and take out the ass y spin basket. Nut loosening direction: to the right (clockwise) Nut fastening direction: to the left (counterclockwise) 7) Lay down the main body so that the front of the out-case faces upward and the remove the 4 bolts that fix the saddle by using the 0 mm box. When laying down the washer, be cautious not to break or scratch the components. (Lay the cloth, on which to work, on the floor.) 8) Remove the 4 bolts that fix the shaft by using the 0 mm box and take out the shaft-ass y. (Please check that the condition of the shaft is same as the figure on the right.) Assemble in reverse order of disassembling. (The Condition During Washing) Since the front left side of the top-cover is fixed by the hook, check that the hook is correctly fixed while assembling the topcover. (The Condition During Spinning) SAMSUNG WASHING MACHINE
5. Troubleshooting * Since the structure of the automatic microcomputer washer is complicated, you may make a service call even though the problem is not caused by the defective product. This section easily explains how to diagnose such problems correctly and how to repair at lower cost. 5- Cautions in repairing or replacing When diagnosing the problem or replacing the part, please ensure that the following instructions are followed ) The static electricity on the plastic part of the washer or on your body may cause to damage the electronic components. Therefore, before working on the PCB, earth by your body or touch the terminal of the washer power plug and the earth wire in order to remove the current difference between your body and the washer. Power Plug Earth Wire ) Since the components on the PCB are coated with the urethane, they cannot be checked by the test rod of the tester. Therefore, check them by carrying out the test mode in order to diagnose the problem according to the results. SAMSUNG ELECTRONICS CO., LTD 9
7. Exploded Views & Part List 7- ASS Y SPIN-BASKET 4 3 5 9 6 7 8 0 3 5 4 6 SAMSUNG ELECTRONICS CO., LTD 3
7. Exploded Views & Part List No Code No Description Specification Q ty Remarks DC66-5089D PULSATOR-CAP ABS DC60-4033A BOLT-PULSATOR STS304,M8,L5 3 DC9-60A ASS'Y-PULSATOR DARK-GRY 4 DC66-5085A PULSATOR-UPPER PP 5 DC66-5086A PULSATOR-LOWER PP 6 DC60-60003A PULSATOR-WASHER T.5 STS304 7 DC60-50003B NUT-SPIN IC,ZNDCI,M8,DARCRO 8 DC60-600B WASHER-WAVE TO.8 STS30 9 DC9-35A ASS'Y BASKET SPIN DARK/GRY 0 DC9-974A ASS'Y-BALANCE DC9-774P ASSY-FILTER NET DC6-6048A GUIDE-WATER FLOW(A) PP(BJ-500) 3 DC6-60483A GUIDE-WATER FLOW(B) 4 DC6-60484A GUIDE-WATER FLOW(C) 5 DC9-36A ASSY SEMI SPIN BASKET STS 304BA 6 DC66-4067A FLANGE-SHAFT ALDC8 4 SAMSUNG WASHING MACHINE
7. Exploded Views & Part List 7- ASS Y TOP-COVER 6 6 3 4 5 9 8 7 3 0 4 6 5 7 8 3 4 6 0 9 7 5 8 SAMSUNG ELECTRONICS CO., LTD 5
7. Exploded Views & Part List No Code No Description Specification Q ty Remarks DC9-6G ASS'Y-LID T.C ABS DC6-07A LID-T.C(U) ABS 3 DC6-08C LID-T.C(L) ABS 4 DC66-90008B MAGNET-R.S T5*W8*L0 5 DC6-60044J CUSHION-LID SILICON 4 6 DC6-700A SPRING-Q(L) STS430 DC6-700B SPRING-Q(R) STS430 7 DC6-0700W COVER-T.C ABS 8 DC6-0657C COVER-SCREW ABS,SUB/EUN BI 9 DC97-00005L ASS'Y-PANEL CONTROL ABS 0 DC6-0699A PANEL-CONTROL ABS DC64-40377R WINDOW-PANEL DC34-30006E SWITCH-REED 5V 0.3A,60mm 3 DC9-5B ASS'Y-L.H 4 MF-ESE-00 ASS'Y-PCB 5 DC6-0698A COVER-TOP ABS 6 DC3-30006A SENSOR-PRESSURE DN-SI 7 DC6-06A HINGE-DOOR(L) POM 8 DC6-06B HINGE-DOOR(R) POM 9 DC90-0079A ASS'Y-POWER CORD EP 0 DC90-004D ASS'Y-CHECKER DC5V/50mA DC6-30307A VALVE WATER PP/SUS(COLD) DC6-4067B SEAL-WATER FORM,D5 3 DC6-4064A SEAL-DETERGENT SILICON,PINK 4 DC6-403B RING-O EPDM NTR 5 DC6-30303B VALVE WATER PP/SUS(HOT) 6 DC6-0053A HOSE-RINSE NBR,ID0,BLK, L4 7 DC65-000B CABLE-TIE DA-00 8 DC97-00080H ASS'Y-DETERGENT ABS 6 SAMSUNG WASHING MACHINE
7. Exploded Views & Part List 7-3 ASS Y CASE-OUTER 3 3 5 7 4 4 0 5 8 0 7 9 8 6 SAMSUNG ELECTRONICS CO., LTD 7
7. Exploded Views & Part List No Code No Description Specification Q ty Remarks DC9-77J ASS'Y-DAMPER FRONT DC9-77K ASS'Y-DAMPER REAR DC6-009A HANDLE P.P 3 DC99-00045A ASS'Y-PAINT SBHG-A 4 DC9-965A ASS'Y-BASE 5 DC6-30330A BASE P.P 6 DC9-795D ASS'Y-LEG 7 DC6-5064A LEG-LEVER FRPP 8 DC6-5007A LEG-SPRING HSWR,YEL&ZPC 9 DC6-5067A LEG-RUBBER NBR BLK 0 6046-00030 STAND OFF ID.5,L,NYLON66 4 DC63-0056D SPONGE-CUSHION FRONT DC63-000L SPONGE-HARNESS T0 W50 L80 BLK 3 DC66-6033B SHEET-DAMPING T.8 00 3 4 ASS'Y-EARTH WIRE 5 DC68-3005K LABEL-RATING YUPO+LAMI 6 DC6-057A COVER-BACK SBHG-A 7 DC6-60074A CLAMP-WIRE SADDLE NYLON#66 8 DC90-90B ASS'Y-PUMP DRAIN 0~40V/50HZ 8 SAMSUNG WASHING MACHINE
7. Exploded Views & Part List 7-4 ASS Y TUB-OUTER 6 5 6 3 (WITHOUT PUMP) 8 5 8 6 9 3 (WITH PUMP) SAMSUNG ELECTRONICS CO., LTD 9
No Code No Description Specification Q ty Remarks DC6-30094A TUB-OUTER P.P DC6-084B CAP-TRIP P.P 3 DC90-68A ASS'Y-WIRE HARNESS(SUB) SUB DC90-44B ASS'Y-WIRE HARNESS(MAIN) MAIN 4 DC6-0670B COVER-TUB P.P 5 DC6-4038A SADDLE SBHG,-ASEW-0 6 DC60-3000A SCREW-MOTOR ZPC(YEL) 4 7 DC9-03L ASS'Y-SHAFT SEM-80N 8 DC9-58E ASS'Y-SCREW SHAFT+MOTOR DIE 4 9 DC3-006H MOTOR-WASHING 0V/50HZ PWS360ZTED 0 DC9-58B ASS'Y-SCREW MOTOR(COATING) 4 DC66-00005A PULLEY-MOTOR DC60-40007A BOLT-HEX M6,L,ZPC,SM8C 3 DC6-70064A DIE-MOTOR SBHG,-A 4 DC6-508J CONDENSOR-M.F 400VAC 5MFD 5 DC66-3004A LINK-DRAIN PP,L66.5 SEW0JL 6 DC3-004A MOTOR-DRAIN 0~40VAC,50/60HZ 7 DC66-04A BELT-V M 8 DC6-09A HOSE-PUMP BLK,L37 PUMP 9 DC6-09A HOSE-DRAIN BLK,L8 PUMP 0 DC9-059A ASS'Y-CASE D.V WITHOUT PUMP DC6-0043A HOSE-O.F NTR WITHOUT PUMP DC66-3004A LINK-DRAIN P.P L66.5 SEW-0JL 30 SAMSUNG WASHING MACHINE
7. Exploded Views & Part List 7-5 ACCESSORY 3 No Code No Description Specification Q ty Remarks DC9-009P ASS'Y-HOSE DRAIN(O) SYSTEM/GRY DC6-04D ASS'Y-HOSE WATER BLUE(NEW-TYPE),.0MT HOT 3 DC6-04C ASS'Y-HOSE WATER PINK(NEW-TYPE),.0MT COLD DC68-0053A INSTRUCTION BOOK DC68-4009A CARD-WARRANTY SAMSUNG ELECTRONICS CO., LTD 3
8. Product Specifications Model No Wash & Spin Capacity Type Power Source Wash & Spin Type SEW-ES(P) 0kg (dry laundry) / 0kg Automatic Washer Single-phase current Whirling type/centrifugal spin type Water Pressure 0.5kg.f/cm ~ 8kg.f/cm Dimensions (mm) W 640 x D 698 x H 998 Weight Rated Power Consumption Rotary Wing Revolution 53kg Motor 557W 8 rpm Spin Revolution 70 rpm Water Level Water Volume Laundry Capacity Detergent Quantity Standard Concentrated High 90 liter Up to 0 kg (blanket 3.5 kg, wool 3.5 kg) 90g 6g Medium 84 liter Up to 7.5 kg (blanket.5 kg, wool.5 kg) 84g 57g Low 65 liter Up to 5 kg 65g 44g Small 5 liter Up to 3 kg 5g 35g Minimum 38 liter Up to.0 kg 38g 6g Standard Water Volume 40 liter 3 SAMSUNG WASHING MACHINE
3. Schematic and Circuit and PCB Pattern Diagram 3- Schematic and Circuit Diagram SAMSUNG ELECTRONICS CO., LTD 4