European Technical Assessment ETA-13/0909 of 8 December 2016 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction product Product family to which the construction product belongs Manufacturer Manufacturing plant Deutsches Institut für Bautechnik Injection system VMU plus for masonry Injection system for use in masonry MKT Metall-Kunststoff-Technik GmbH & Co. KG Auf dem Immel 2 67685 Weilerbach DEUTSCHLAND Werk 2, D This European Technical Assessment contains This European Technical Assessment is issued in accordance with Regulation (EU) No 305/2011, on the basis of 61 pages including 3 annexes which form an integral part of this assessment Guideline for European technical approval of "Metal Injection Anchors for Use in Masonry", ETAG 029, April 2013, used as European Assessment Document (EAD) according to Article 66 Paragraph 3 of Regulation (EU) No 305/2011. Z73822.16 8.06.04-256/16
European Technical Assessment ETA-13/0909 Page 2 of 61 8 December 2016 The European Technical Assessment is issued by the Technical Assessment Body in its official language. Translations of this European Technical Assessment in other languages shall fully correspond to the original issued document and shall be identified as such. Communication of this European Technical Assessment, including transmission by electronic means, shall be in full. However, partial reproduction may only be made with the written consent of the issuing Technical Assessment Body. Any partial reproduction shall be identified as such. This European Technical Assessment may be withdrawn by the issuing Technical Assessment Body, in particular pursuant to information by the Commission in accordance with Article 25(3) of Regulation (EU) No 305/2011. Z73822.16 8.06.04-256/16
European Technical Assessment ETA-13/0909 Page 3 of 61 8 December 2016 Specific Part 1 Technical description of the product The Injection System VMU plus for masonry is a bonded anchor (injection type) consisting of a mortar cartridge with injection mortar VMU plus or VMU plus Polar, a perforated sleeve and an anchor rod with hexagon nut and washer. The steel elements are made of zinc coated steel or stainless steel. The anchor rod is placed into a drilled hole filled with injection mortar and is anchored via the bond between steel element, injection mortar and masonry and mechanical interlock. The Illustration and the description of the product are given in Annex A. 2 Specification of the intended use in accordance with the applicable European Assessment Document The performances given in Section 3 are only valid if the anchor is used in compliance with the specifications and conditions given in Annex B. The verifications and assessment methods on which this European Technical Assessment is based lead to the assumption of a working life of the anchor of at least 50 years. The indications given on the working life cannot be interpreted as a guarantee given by the producer, but are to be regarded only as a means for choosing the right products in relation to the expected economically reasonable working life of the works. 3 Performance of the product and references to the methods used for its assessment 3.1 Mechanical resistance and stability (BWR 1) Essential characteristic Characteristic resistance for steel elements Characteristic resistance for anchors in masonry units Displacements under shear and tension loads Reduction Factor for job site tests (β-factor) Edge distances and spacing Group factor for group fastenings Performance See Annex C2 See Annex C3 C45 See Annex C4 C45 See Annex C1 See Annex C3 C45 See Annex C3 C45 3.2 Safety in case of fire (BWR 2) Essential characteristic Reaction to fire Resistance to fire Performance Class A1 No performance assessed 3.3 Hygiene, health and the environment (BWR 3) Regarding dangerous substances there may be requirements (e.g. transposed European legislation and national laws, regulations and administrative provisions) applicable to the products falling within the scope of this European Technical Assessment. In order to meet the provisions of Regulation (EU) No 305/2011, these requirements need also to be complied with, when and where they apply. Z73822.16 8.06.04-256/16
European Technical Assessment ETA-13/0909 Page 4 of 61 8 December 2016 3.4 Safety in use (BWR 4) The essential characteristics regarding Safety in use are included under the Basic Works Requirement Mechanical resistance and stability. 4 Assessment and verification of constancy of performance (AVCP) system applied, with reference to its legal base In accordance with guideline for European technical approval ETAG 029, April 2013 used as European Assessment Document (EAD) according to Article 66 Paragraph 3 of Regulation (EU) No 305/2011 the applicable European legal act is: [97/177/EC]. The system to be applied is: 1 5 Technical details necessary for the implementation of the AVCP system, as provided for in the applicable European Assessment Document Technical details necessary for the implementation of the AVCP system are laid down in the control plan deposited at Deutsches Institut für Bautechnik. Issued in Berlin on 8 December 2016 by Deutsches Institut für Bautechnik Andreas Kummerow p.p. Head of Department beglaubigt: Wittstock Z73822.16 8.06.04-256/16
Page 5 of European Technical Assessment
Page 6 of European Technical Assessment
Page 7 of European Technical Assessment
Page 8 of European Technical Assessment
Page 9 of European Technical Assessment
Page 10 of European Technical Assessment
Page 11 of European Technical Assessment
Page 12 of European Technical Assessment
Page 13 of European Technical Assessment
Page 14 of European Technical Assessment
Page 15 of European Technical Assessment
Page 16 of European Technical Assessment
Page 17 of European Technical Assessment
Page 18 of European Technical Assessment
Page 19 of European Technical Assessment
Page 20 of European Technical Assessment
Page 21 of European Technical Assessment
Page 22 of European Technical Assessment
Page 23 of European Technical Assessment
Page 24 of European Technical Assessment
Page 25 of European Technical Assessment
Page 26 of European Technical Assessment
Page 27 of European Technical Assessment
Page 28 of European Technical Assessment
Page 29 of European Technical Assessment
Page 30 of European Technical Assessment
Page 31 of European Technical Assessment
Page 32 of European Technical Assessment
Page 33 of European Technical Assessment
Page 34 of European Technical Assessment
Page 35 of European Technical Assessment
Page 36 of European Technical Assessment
Page 37 of European Technical Assessment
Page 38 of European Technical Assessment
Page 39 of European Technical Assessment
Page 40 of European Technical Assessment
Page 41 of European Technical Assessment
Page 42 of European Technical Assessment
Page 43 of European Technical Assessment
Page 44 of European Technical Assessment
Page 45 of European Technical Assessment
Page 46 of European Technical Assessment
Page 47 of European Technical Assessment
Page 48 of European Technical Assessment
Page 49 of European Technical Assessment
Page 50 of European Technical Assessment
Page 51 of European Technical Assessment
Page 52 of European Technical Assessment
Page 53 of European Technical Assessment
Page 54 of European Technical Assessment
Page 55 of European Technical Assessment
Page 56 of European Technical Assessment
Page 57 of European Technical Assessment
Page 58 of European Technical Assessment
Page 59 of European Technical Assessment
Page 60 of European Technical Assessment
Page 61 of European Technical Assessment