Λευκωσία, 8 Δεκεμβρίου ΘΕΜΑ: November 2016 Notification Procedure 1025/2012. Κυρία/Κύριε,

Λευκωσία, 8 Δεκεμβρίου 2016 ΠΡΟΣ: Όλα τα Μέλη ΘΕΜΑ: November 2016 Notification Procedure 1025/2012 Κυρία/Κύριε, Σας επισυνάπτουμε γνωστοποιήσεις από Εθνικούς Οργανισμούς Τυποποίησης, μελών των Ευρωπαϊκών Οργανισμών Τυποποίησης CEN/CENELEC, που περιέχουν τους τίτλους προτεινόμενων εθνικών προτύπων. Σύμφωνα με την Ευρωπαϊκή Οδηγία που αφορά την πληροφόρηση σε θέματα τεχνικών προτύπων, μπορείτε, αφού μελετήσετε τους τίτλους: α) να ζητήσετε όπως λάβετε ηλεκτρονικά ολόκληρο το κείμενο του προσχεδίου εθνικού προτύπου, εάν αυτό είναι διαθέσιμο, β) να συμμετάσχετε στις συναντήσεις της τεχνικής επιτροπής του Εθνικού Οργανισμού Τυποποίησης που ετοιμάζει το προσχέδιο προτύπου και γ) να υποβάλετε εισήγηση στον CYS, να αρχίσει τυποποιητική εργασία σε Ευρωπαϊκό επίπεδο σχετικά με το θέμα της γνωστοποίησης, εάν φυσικά πιστεύετε ότι το εν λόγω εθνικό πρότυπο θα επηρεάσει την ελεύθερη διακίνηση προϊόντων ή την κυπριακή βιομηχανία και οικονομία. Τυχόν σχόλια και παρατηρήσεις παρακαλώ όπως υποβάλλονται στον Κυπριακό Οργανισμό Τυποποίησης. Σε περίπτωση που δεν υπάρξει οποιαδήποτε ανταπόκριση, ο CYS δε θα φέρει ένσταση στην προώθηση των υπό αναφορά εθνικών προτύπων. Για περισσότερες πληροφορίες μπορείτε να επικοινωνείτε με την κα. Μαριλένα Νικολάου, Λειτουργό Διοίκησης και Διεθνών Σχέσεων του Κυπριακού Οργανισμού Τυποποίησης (CYS), τηλ: 22 411439, Φαξ. 22 411511 και στην ηλεκτρονική διεύθυνση: m.nicolaou@cys.org.cy Με εκτίμηση, Ανδρέας Ανδρέου, Αναπλ. Διευθυντής Τμήματος Βιομηχανίας, για Γενικό Γραμματέα. /ΜΚ. Γρίβα Διγενή 38 & Δεληγιώργη 3, 1066, Τ.Θ. 21455, 1509 Λευκωσία, Κύπρος, Τηλ. + 357-22889860, Φαξ. + 357-22665685, E-mail: meropi@ccci.org.cy, Ιστοσελίδα:www.ccci.org.cy

Information procedure Page 1 Monthly Notifications Register Notifications registered at CCMC from 2016-11-01 to 2016-11-30 Register issued on : 2016-12-05 A list of subsectors can be found at the end of this document.

Information procedure Page 2 Monthly Notifications Register Notifications registered at CCMC from 2016-11-01 to 2016-11-30 Sector A : SERVICES Register issued on : 2016-12-05

Subsector A11: SAFETY AND SECURITY Page 3 Subsector : A11 Registration Date : 2016-11-18 TSE Turkey ID : t0109691/0001 03.080.30 Work places - Rules for selling of mineral and grease lubricants This standard, includes, rules for management structural properties, technical equipment and personnel characteristics for selling of mineral and grease lubricants Subsector : A11 Registration Date : 2016-11-18 TSE Turkey ID : t0109693/0001 03.080.30 Workplaces - Places of manufacturing, assembly and service for acrylic solid surfaces kitchen and bath benchtops and wall covers - Rules This standard, includes, rules for management structural properties, technical equipment and personnel characteristics for manufacturing, assembly and service for acrylic solid surfaces kitchen and bath benchtops and wall covers Subsector : A11 Registration Date : 2016-11-18 TSE Turkey ID : t1008357/0001 03.080.30 Work places - Public toilets - The classification, - General and spesific rules The concept of this standard is about the classificaion and requirements of public lavatories (including toursimplus) Subsector : A11 Registration Date : 2016-11-18 TSE Turkey ID : tst11526/0001 03.080.30

Auto cleaning, washing and oilling places- General rules This standard includes general rules for auto cleaning, washing and oilling places. Page 4 Subsector : A11 Registration Date : 2016-11-25 TSE Turkey ID : tst12713/0002 03.080.30, 33.160.25, 33.170 Competent services - Rules for satellite receiver systems This standard includes rules for management, structural features, technical equipment, personnel specifications and certification of competent services for satellite receiver systems. Subsector : A11 Registration Date : 2016-11-18 TSE Turkey ID : tst13027/0001 03.080.30 Hygiene and sanitation at food production places-general rules This standard, includes, rules for management structural properties, technical equipment and personnel characteristics of hygiene for whole and retail food production and consumption Subsector : A11 Registration Date : 2016-11-25 TSE Turkey ID : tst13166/0002 03.080.30, 35.180 Competent services - Rules for queue and call system (queue-matic) This standard includes rules for management, structural features, technical equipment, personnel specifications and certification of competent services of queue and call system (queue-matic).

Subsector : A11 Registration Date : 2016-11-25 TSE Turkey ID : tst13560/0001 03.080.30, 29.130.01 Competent services - Rules for satellite based positioning (GPS) and/or navigation equipments This standard includes satellite based positioning equipments competent services rules about technical equipment, operation management, structural situation and functions of staff Page 5 Subsector : A11 Registration Date : 2016-11-18 TSE Turkey ID : tst13820/0001 03.080.30 Work places - Places Produced Powder Control Systems - General rules This standard includes the general rules for structural characteristics, management and workers characteristics of places produced powder control systems. Subsector A99: UNDETERMINED Subsector : A99 Registration Date : 2016-11-18 TSE Turkey ID : tst11827/0001 03.080.10 Work places Rules for providing maintenance and filling service for fire extinguishers This standard includes rules for structural characteristics, operating, personal and technical equipment providing maintenance and filling service for fire extinguishers ** End of Sector **

Information procedure Page 6 Monthly Notifications Register Notifications registered at CCMC from 2016-11-01 to 2016-11-30 Sector B : BUILG AND CONSTRUCTION Register issued on : 2016-12-05

Subsector B01: FIRE PROTECTION Page 7 Subsector : B01 Registration Date : 2016-11-21 ASI Austria ID : 00026999/0001 13.220 ÖNORM F 3032 Components of automatic fire detection systems - Fire brigade key box - Requirements and test specifications This ÖNORM defines requirements and test specifications for the fire brigade key box. The fire brigade key box is a part of an automatic firefighting system. It shall be installed in those cases, were it is not ensured by a company, that in case of a fire, the fire brigade has access to the building at any time. Subsector : B01 Registration Date : 2016-11-16 ID : 03101084/0001 03101084 Fire brigade training facilities - Part 1: General requirements Subsector : B01 Registration Date : 2016-11-16 ID : 03101085/0001 03101085 Fire brigade training facilities - Part 2: Gas-operated representation appliances Subsector : B01 Registration Date : 2016-11-16 ID : 03101086/0001 03101086 Fire brigade training facilities - Part 3: Wood fired fire brigade training facilities

Page 8 Subsector : B01 Registration Date : 2016-11-16 ID : 03101088/0001 03101088 Firefighting vehicles - Part 5: Group pumping appliance LF 10; Amendment A2 Subsector : B01 Registration Date : 2016-11-16 ID : 03101089/0001 03101089 Fire-fighting vehicles - Part 11: Group pumping appliance LF 20; Amendment A2 Subsector : B01 Registration Date : 2016-11-16 ID : 03101090/0001 03101090 Firefighting vehicles - Part 18: Pump water tanker TLF 2000; Amendment A1 Subsector : B01 Registration Date : 2016-11-16 ID : 03101091/0001 03101091 Firefighting vehicles - Part 21: Pump water tanker TLF 4000; Amendment A1 Subsector : B01 Registration Date : 2016-11-16

Page 9 ID : 03101092/0001 03101092 Fire fighting vehicle - Part 22: Pump water tanker TLF 3000; Amendment A1 Subsector : B01 Registration Date : 2016-11-16 ID : 03101093/0001 03101093 Firefighting vehicles - Part 26: Group pumping appliance for rescue operations HLF 10; Amendment A2 Subsector : B01 Registration Date : 2016-11-16 ID : 03101094/0001 03101094 Fire-fighting vehicles - Part 27: Group pumping appliance for rescue operations HLF 20; Amendment A2 Subsector : B01 Registration Date : 2016-11-16 ID : 03101101/0001 03101101 Firefighting and fire protection - Mobile generators for the supply of electrical equipment and for the building supply Subsector : B01 Registration Date : 2016-11-16

Page 10 ID : 03101106/0001 03101106 Firefighting and fire protection - Permanently installed generator (generating set) <kleiner> 12 kva, 230 V/400 V for the use in firefighting vehicles Subsector B02: STRUCTURES Subsector : B02 Registration Date : 2016-11-04 BSI United Kingdom ID : 01603028/0001 BS 8533 Assessing and managing flood risk in development - Code of practice Subsector : B02 Registration Date : 2016-11-04 BSI United Kingdom ID : 01603298/0001 BS 1377-3 Methodsoftestforsoilsforcivilengineeringpurposes.Part3:Chemicaland electro-chemical testing Subsector B05: FIRE TESTS Subsector : B05 Registration Date : 2016-11-25 LST Lithuania ID : 10002385/0001 13.220.50 Reaction to fire tests. Method for determining combustibility characteristics This test method is applicable to solid non-metallic materials, including building materials and products (hereinafter - the material) containing more than 3% of organic material and does not apply to materials with one-sided finish or non-combustible cover. This test method is intended for determination of material flammability characteristics (weight loss

Page 11 and temperature increase) in research and control work and is not intended for classification of building materials according to LST EN 13501-1. Subsector B07: GLASS Subsector : B07 Registration Date : 2016-11-04 BSI United Kingdom ID : 01603133/0001 BS 6262-1 Glazingforbuildings.Part1:Generalmethodologyfortheselectionof glazing Subsector : B07 Registration Date : 2016-11-04 BSI United Kingdom ID : 01603134/0001 BS 6262-4 Glazingforbuildings.Part4:Codeofpracticeforsafetyrelatedtohuman impact Subsector : B07 Registration Date : 2016-11-04 BSI United Kingdom ID : 01603135/0001 BS 6262-7 Glazingforbuildings.Part7:Codeofpracticefortheprovisionof information Subsector B08: DOORS AND WINDOWS Subsector : B08 Registration Date : 2016-11-16

Page 12 ID : 00517835/0001 00517835 Locks - Mortice locks - Part1: Mortice locks for rebated doors Subsector : B08 Registration Date : 2016-11-04 BSI Draft Issue Date : 2016-09-21 United Kingdom Latest Date for Comments : 2016-11-21 ID : 01602515/0001 Draft for public enquiry BS 6375-1:2015/A1 BS6375-1AMD1.Performanceofwindowsanddoors.Part1.Classificationfor weathertightness and guidance on selection and specification. Amendment Subsector : B08 Registration Date : 2016-11-25 TSE Turkey ID : tst01904/0003 91.060.50 Doorframes-Steelsheet This standard specifies external and internal door frames fabricated from steel sheet European : Modified BS 1245:2012 Subsector : B08 Registration Date : 2016-11-25 TSE Turkey ID : tst01904/0003 91.060.50 Doorframes-Steelsheet This standard specifies external and internal door frames fabricated from steel sheet European : Modified 18111-1:2004 Subsector : B08 Registration Date : 2016-11-25 TSE Turkey

Page 13 ID : tst01904/0003 91.060.50 Doorframes-Steelsheet This standard specifies external and internal door frames fabricated from steel sheet European : Modified 18111-1:2005 Subsector : B08 Registration Date : 2016-11-25 TSE Turkey ID : tst01904/0003 91.060.50 Doorframes-Steelsheet This standard specifies external and internal door frames fabricated from steel sheet European : Modified 18111-2:2004 Subsector B14: GEOTECHNICS Subsector : B14 Registration Date : 2016-11-16 ID : 00517899/0001 00517899 Soil - Calculation of embankment failure and overall stability of retaining structures; Amendment 1 Subsector : B14 Registration Date : 2016-11-25 TSE Turkey ID : ts104671/0001 93.020 Soil control tests in place - Part 6: Determination of density of soil and rock in-place at depths below surface by nuclear methods This test method covers the calculation of the density of soil and rock by the attenuation of gamma radiation, where the gamma source and the gamma detector are placed at the desired depth in a bored hole lined by an access tube.

Page 14 International : Modified ASTM D5195-14:2014 Subsector : B14 Registration Date : 2016-11-25 TSE Turkey ID : ts104672/0001 13.080.20 Soil control tests in place - Part 7: Determination of in-place density and water content of soil and soil-aggregate by nuclear methods (shallow depth) This test method describes the procedures for measuring in-place density and moisture of soil and soil-aggregate by use of nuclear equipment. International : Modified ASTM D6938-15:2015 Subsector B17: LIGHTING EQUIPMENT AND LIGHTING APPLICATION TECHNOLOGY Subsector : B17 Registration Date : 2016-11-16 ID : 05800824/0001 05800824 Phosphorescent pigments and products - Part 1: Measurement and marking at the producer Subsector B18: SCAFFOLG Subsector : B18 Registration Date : 2016-11-04 BSI United Kingdom ID : 01602968/0001 BS 5975:2018 Codeofpracticefortemporaryworksproceduresandthepermissiblestress design of falsework Subsector B20: DRAINAGE EQUIPMENT Subsector : B20 Registration Date : 2016-11-21 ASI

Page 15 Austria ID : 00027009/0001 23.040.01, 93.025, 93.030 ÖNORM B 5010 Quality assurance of pipeline components for installations in buildings, hydraulic installations for housing and industry - General principles This Austrian Standard provides general principles for quality assurance of pipeline components (pipes, fittings, valves and connections), which are used in municipal and industrial water systems. The requirements for the respective pipe members, the applicable test methods and the specific rules of quality assurance are specified in the applicable document of such products. Moreover, the present ÖNORM is generally effective for securing the quality characteristics of pipeline components and also serves as a basis for quality assurance in the relevant measure-effective standards. This ÖNORM can be applied also for the quality assurance of pipeline components in buildings. Subsector : B20 Registration Date : 2016-11-21 ASI Austria ID : 00027010/0001 13.060.30, 17.120.01, 17.120.20 ÖNORM B 2509 Flow measurement in wastewater systems This ÖNORM is applied to measure the flow in sewage systems using measuring devices. The document describes Venturi channels, flowmeters and other measurement methods. Subsector : B20 Registration Date : 2016-11-29 UNI Italy ID : 01601919/0001 93.080.30 UNI1601919 Gully tops and manhole tops for vehicular and pedestrian areas Indications regarding the application of standard EN 124:2015 This technical report is an informative document, with the purpose of giving information on the application in Italy of the standard EN 124:2015. Subsector B22: WALLCOVERINGS

Page 16 Subsector : B22 (Secondary Subsector) Registration Date : 2016-11-29 UNI Italy ID : 01602371/0001 73.020, 91.100.15 UNI1602371 Natural stone test methods Determination of the measure of the staining of stone surfaces The standard describes a test method to measure colour differences by staining the surface with several staining agents. Subsector B25: GAS DISTRIBUTION INSTALLATION AND RELATED EQUIPMENT Subsector : B25 Registration Date : 2016-11-04 BSI United Kingdom ID : 01602917/0001 BS 6172:2010+A1 Installation,servicingandmaintenanceofdomesticgascookingappliances. Specification. Amendment Subsector : B25 Registration Date : 2016-11-03 NEN Netherlands ID : 50002009/0001 75.200, 91.140.40 NEN 7244-7:2016 Concept nl Dutch edition on base of NEN-EN 12327 - Gas supply systems - Pipelines for maximum operating pressure up to an d including 16 bar - Part 7: Specific functional requirements for strength- and tightness testing and for commissioning and decommissioning of gasdistribution pipelines Is applicable to the design, installation, testing, use, disuse, management, maintenance, renovation of pipework and all related activities. Subsector B26: ROAD BUILG AND MAINTENANCE Subsector : B26 Registration Date : 2016-11-04 SNV Draft Issue Date : 2016-11-01

Page 17 Switzerland Latest Date for Comments : 2016-12-20 ID : CH160019/0001 Draft for public enquiry 93.080.10 prsn 640517 Surfaceproperties; longitudinal evenness Subsector : B26 Registration Date : 2016-11-04 SNV Draft Issue Date : 2016-11-01 Switzerland Latest Date for Comments : 2016-12-20 ID : CH160020/0001 Draft for public enquiry 93.080.10 prsn 640518 Surface properties; transversal evenness Subsector B28: FLOOR COVERINGS Subsector : B28 Registration Date : 2016-11-29 UNI Italy ID : 01602371/0001 73.020, 91.100.15 UNI1602371 Natural stone test methods Determination of the measure of the staining of stone surfaces The standard describes a test method to measure colour differences by staining the surface with several staining agents. Subsector : B28 Registration Date : 2016-11-04 BSI United Kingdom ID : 01602797/0001 BS 8203 Code of practice for installation of resilient floor coverings

Subsector B31: HEATING SYSTEMS IN BUILGS Page 18 Subsector : B31 Registration Date : 2016-11-21 ASI Austria ID : 00027005/0001 91.140.10 ÖNORM M 7510-1 Checking of heating systems -- Part 1: General requirements and inspection -- National amendment referring to ÖNORM EN 15378 This Austrian Standard is the national supplement to the ÖNORM EN 15378 and enables the checking and evaluation of the energy efficiency and the emission performance of a heating system. This checking does not replace safety-related checkings, customer service or inspection works and type tests. Subsector : B31 Registration Date : 2016-11-16 ID : 04111905/0001 04111905 Process heat installations for more than one kind of energy; one boiler for solid fuel and one for oil or gas and only one chimney; safety requirements and tests Subsector B99: UNDETERMINED Subsector : B99 Registration Date : 2016-11-21 ASI Austria ID : 00027006/0001 65.020.20, 65.020.40 ÖNORM L 1110 Plants - Quality requirements, provisions for sorting This ÖNORM is for assessing plants for garden design and landscaping requirements in terms of quality and sorting provisions. Further, it contains provisions on packaging and transportation as well as the identity of plants. It also serves as the basis for the preparation of tenders and services offered by the garden design and landscape construction, especially when ÖNORM L 2241 as part of the contract is agreed. The tasks of garden design and landscaping is arranged in ÖNORM L 1111.

Subsector : B99 Registration Date : 2016-11-21 ASI Austria ID : 00027007/0001 13.030.40, 13.030.99 ÖNORM S 2205 Technical requirements for composting plants The present ÖNORM specifies the minimum technical standard for composting plants. Page 19 Subsector : B99 Registration Date : 2016-11-16 ID : 00517895/0001 91.120.30 18534-6/A1 Waterproofing for indoor applications - Part 6: Waterproofing with waterproofing materials in panel-shaped form in conjunction with tiles or paving; Amendment A1 Subsector : B99 Registration Date : 2016-11-29 UNI Italy ID : 01602384/0001 03.040, 91.010.30 UNI1602384 Building and civil engineering works - Digital management of the informative processes - Part 7: Knowledge, skill and competence requirements of building information modelling profiles This standard describes requirements for the building information modelling professional profiles. These requirements are defined in terms of knowledge, skills and competence, in accordance with the European Qualifications Framework, EQF. Subsector : B99 Registration Date : 2016-11-11 AENOR Spain Latest Date for Comments : 2016-12-21 ID : P0044285/0001 Draft for public enquiry PNE 41810 Conservation of Cultural Heritage. Intervention Criteria for Stone Materials. This document provides guidelines and recommendations on the conservation of stone cultural heritage. This document his mainly aimed at cultural heritage stakeholders involved

Page 20 in stone cultural heritage projects and in quality control interventions. ** End of Sector **

Information procedure Page 21 Monthly Notifications Register Notifications registered at CCMC from 2016-11-01 to 2016-11-30 Sector C : CHEMICALS, CHEMICAL ENGINEERING AND FOOD PRODUCTS Register issued on : 2016-12-05

Subsector C01: Food products Page 22 Subsector : C01 Registration Date : 2016-11-29 UNI Italy ID : 01602160/0001 67.100.10 UNI1602160 Method for lactose, glucose and galactose analysis of hard, long ripened cheese This technical specification describes the method for analyzing, in hard-long ripened cheese, the content of lactose, glucose and galactose, using High Performance Anion-Exchange Chromatography with Pulsed Amperometric Detector (HPAEC-PAD). This technical specification is applicable to hard cheese in which both the reduction of lactose and the further metabolization of glucose and galactose, naturally occurred during the technological process by the action of microflora.. It is not applicable to dairy products in which the lactose hydrolysis has been obtained by the addition of the beta- galactosidase enzyme, and consequently contain high concentration of glucose and galactose. The method has been validated by only one laboratory. Subsector : C01 Registration Date : 2016-11-16 ID : 05701944/0001 05701944 Analysis of foodstuffs - Determination of Salmonella with impedance-method Subsector : C01 Registration Date : 2016-11-16 ID : 05701986/0001 05701986 Food hygiene - Production and immediate dispense of ice-cream to the consumer - Hygiene requirements, testing Subsector : C01 Registration Date : 2016-11-28 MSZT Hungary ID : 60401607/0001

Page 23 67.060, 67.060 MSZ 6369-7 Flour test methods. Part 7: Determination of grade of grinding REV/AMD MSZ 6369-7:1978 Subsector : C01 (Secondary Subsector) MSZT Hungary ID : 60401607/0001 Registration Date : 2016-11-28 67.060, 67.060 MSZ 6369-7 Flour test methods. Part 7: Determination of grade of grinding REV/AMD MSZ 6369-7:1978 Subsector C03: CHEMISTRY Subsector : C03 Registration Date : 2016-11-11 AENOR Spain Latest Date for Comments : 2016-12-21 ID : P0044999/0001 Draft for public enquiry PNE 84642 Cosmetic raw materials. Sodium cocoamphoacetate. This standard includes the specifications required by the sodium cocoamphoacetate in cosmetic uses. REV/AMD UNE 84642:2002 Subsector C06: ESSENTIAL OILS Subsector : C06 Registration Date : 2016-11-16 ID : 00200936/0001 00200936 Binders for paints and varnishes - Castor oil - Requirements and methods of test

Subsector C18: ADHESIVES Page 24 Subsector : C18 Registration Date : 2016-11-16 ID : 04200924/0001 79.060.10 53255 Testing of wood adhesives and glued wood joints - Mechanical delamination tests by grooving and chopping Subsector C19: CHEMICAL ANALYSIS Subsector : C19 Registration Date : 2016-11-21 ASI Austria ID : 00027008/0001 13.080.99 ÖNORM L 1075 Principles for the evaluation of the content of selected elements in soils This Austrian Standard is used to assess the contents of the following elements in the fine earth (<2 mm) and in the humus layer: arsenic (As), lead (Pb), cadmium (Cd), chromium (Cr), cobalt (Co), copper (Cu), molybdenum (Mo), nickel (Ni), mercury (Hg), selenium (Se), thallium (Tl), uranium (U), vanadium (V), zinc (Zn). These elements are natural in all soils against natural. Depending on the content they can also have negative effects on the environment. Subsector : C19 Registration Date : 2016-11-16 ID : 02703053/0001 39.060 13093 Screening test for nickel release from consumer items which are inserted into pierced parts of the human body and consumer items that come into direct and prolonged contact with the skin Subsector C20: EXPLOSIVES AND FIREWORKS

Page 25 Subsector : C20 Registration Date : 2016-11-08 TSE Turkey ID : t0109806/0001 95.020 Glossary of mine action terms, definitions and abbreviations This standard covers terms, definitions and abbreviations of mine action Subsector : C20 Registration Date : 2016-11-25 TSE Turkey ID : ts113628/0001 71.100.30, 95.020 Humanitarian mine action - Quality management - Quality assurance (QA) and quality control (QC) for mechanical demining This standard covers quality management in humanitarian demining in general as well as associated with demining machines. The standard also focuses on specific actions for quality assurance (QA) and quality control (QC) in the use of demining machines at hazardous sites. Subsector : C20 Registration Date : 2016-11-25 TSE Turkey ID : ts113629/0001 71.100.30, 95.020 Humanitarian Mine Action - Test and evaluation - Metal Detectors This standard covers principles and procedures for the testing and evaluation of metal detectors. Subsector C99: UNDETERMINED Subsector : C99 Registration Date : 2016-11-28 UNMZ Draft Issue Date : 2016-11-30 Czech Republic Latest Date for Comments : 2017-02-28 ID : 01007116/0001

Safety code for working in chemical laboratories Page 26 Subsector : C99 Registration Date : 2016-11-16 ID : 01200628/0001 01200628 Support rings and ring supports on apparatus - Part 1: Calculation of stability, Types, dimensions, calculation of thickness, dimensions and maximum service weight for nonalloy and stainless steel agiation vessels Subsector : C99 Registration Date : 2016-11-16 ID : 06235004/0001 25.220.20 19279 Photocatalytic activity of surfaces - Determination of the photocatalytic deposition velocity of nitrogen monoxide at photocatalytically active surfaces ** End of Sector **

Information procedure Page 27 Monthly Notifications Register Notifications registered at CCMC from 2016-11-01 to 2016-11-30 Sector F : FUNDAMENTAL STANDARDS Register issued on : 2016-12-05

Subsector F02: UNITS & SYMBOLS Page 28 Subsector : F02 Registration Date : 2016-11-16 ID : 15202651/0001 15202651 Units - Conversion of non-si units Subsector F05: MEASURING INSTRUMENTS Subsector : F05 Registration Date : 2016-11-21 ASI Austria ID : 00027000/0001 01.040.17, 17.120.20 ÖNORM B 2401 Hydrometry - Methods for the determination of liquid flow and velocity in open channels This ÖNORM describes the methods for determining the flow and / or the flow rate in open channels and their application range and accuracy attainable. This ÖNORM contains no hazards in terms of carrying out measurements in open channels. It is the responsibility of the user to establish appropriate safety and health measures Subsector : F05 Registration Date : 2016-11-29 UNI Italy ID : 01602368/0001 33.200 UNI1602368 Communication systems for meters - Shared management of communication band at 169 MHz This technical specification establishes the requirements for shared management of communications in the 169 MHz frequency band and the coexistence of various services related to different utilities (e.g. gas, electricity, water, heat). Subsector : F05 Registration Date : 2016-11-16 ID : 15202649/0001

Page 29 17.120.10 19216 Flow Measurement - Mounting arrangements for flow measuring devices according to the differential pressure method Subsector F14: GRAPHICAL TECHNOLOGY, SIGN-BOARDS AND NAMEPLATES Subsector : F14 Registration Date : 2016-11-16 ID : 01700032/0001 01.040.37 16609 Printing technology - Porous printing - Terms Subsector : F14 Registration Date : 2016-11-16 ID : 01700033/0001 01.040.37 16500 Printing technology - Basic terms Subsector F20: QUALITY ASSURANCE Subsector : F20 Registration Date : 2016-11-25 TSE Turkey ID : tst10004/0001 03.120.10 Military quality assurance requirements for production Standard contains the requirements, which, if applied appropriately, provide confidence in the Supplier s capability to deliver product that conforms to Acquirer contract requirements.

Page 30 Subsector : F20 Registration Date : 2016-11-25 TSE Turkey ID : tst10005/0001 03.120.10 Military quality assurance requirements for inspection and test Standard contains the requirements, which, if applied appropriately, provide confidence in the Supplier s capability to deliver product that conforms to Acquirer contract requirements Subsector F99: UNDETERMINED Subsector : F99 Registration Date : 2016-11-16 ID : 09500470/0002 09500470 Comparative testing - Technical principles ** End of Sector **

Information procedure Page 31 Monthly Notifications Register Notifications registered at CCMC from 2016-11-01 to 2016-11-30 Sector H : PRODUCTS FOR HOUSEHOLD AND LEISURE USE Register issued on : 2016-12-05

Subsector H04: SPORTS EQUIPMENT Page 32 Subsector : H04 Registration Date : 2016-11-21 ASI Austria ID : 00026995/0001 97.220.20 ÖNORM ISO 8061 Alpine ski-bindings - Selection of release torque values This International Standard specifies methods for the selection of the release torques for alpine skibindings. It gives information necessary to determine the release torques; these are to be recommended for use by ski-binding manufacturers in their instructions for installation and use, and by ski shops for the adjustment of already mounted ski-bindings. It applies to alpine ski-bindings in current use. Subsector : H04 Registration Date : 2016-11-21 ASI Austria ID : 00026996/0001 97.220.20 ÖNORM ISO 8783 Alpine skis - Guidelines for conducting slope performance tests This International Standard provides guidelines for carrying out comparative testing of alpine skis with the objective of evaluating the performance characteristics. It is applicable to alpine skis in accordance with ISO 6289. Subsector : H04 Registration Date : 2016-11-21 ASI Austria ID : 00027011/0001 97.220.20 ÖNORM ISO 9523 Touring ski-boots for adults - Interface with touring ski-bindings - Requirements and test methods This International Standard specifies the dimensions and characteristics of the interface, requirements, test methods, and marking of ski-boots with a rigid sole which are used with current Systems of touring ski-bindings with attachment at the boot toe and boot heel, the proper release function of which depends on the dimensions and design of the interfaces. Subsector : H04 Registration Date : 2016-11-21 ASI

Austria ID : 00027012/0001 97.220.20 ÖNORM ISO 11110 Winter-sports equipment - Test devices for the setting of the functional unit ski/boot/binding - Requirements and tests This International Standard specifies the tests and requirements for devices used to determine the release moments of ski-bindings in retail sales, rental, and other facilities. It specifies requirements for the design accuracy, operation, maintenance, and calibration of the test devices used for determining binding release settings. Page 33 Subsector : H04 Registration Date : 2016-11-16 ID : 11201161/0001 97.220.40 79018 Paragliding equipment - Paramotor gliders - Requirements and test methods for structural strength and determination of flight safety characteristics Subsector : H04 Registration Date : 2016-11-16 ID : 11201186/0001 11201186 Detection and alert systems for emergencies under water in swimming pools - Safety requirements and test methods Subsector H09: FURNITURE Subsector : H09 Registration Date : 2016-11-04 BSI Draft Issue Date : 2016-10-13 United Kingdom Latest Date for Comments : 2016-12-14 ID : 01602470/0001 Draft for public enquiry BS 6222-2:2009+A1 Domestic kitchen equipment Domestickitchenequipment.Fittedkitchenunits,peninsular units, island units and breakfast bars. Performance requirements and test methods. Amendment

Page 34 Subsector H19: NON-ELECTRIC COOKERS AND BARBECUES Subsector : H19 Registration Date : 2016-11-04 BSI Draft Issue Date : 2016-11-02 United Kingdom Latest Date for Comments : 2017-01-11 ID : 01602403/0001 Draft for public enquiry BS 8303 BS8303.Installationofdomesticheatingandcookingappliancesburningwood, woody biomass and solid mineral fuels. Specification Subsector H25: LARGE GAS APPLIANCES Subsector : H25 Registration Date : 2016-11-16 ID : 04000344/0001 97.040.10 18861-2 Equipment for commercial kitchens - Dishwashing facilities and sinks - Part 2: Sinks, Requirements and testing Subsector : H25 Registration Date : 2016-11-16 ID : 04000348/0001 97.040.10 18865-4 Equipment for commercial kitchens - Food distribution equipment - Part 4: Top shelves heated or not heated, Requirements and testing Subsector H99: UNDETERMINED Subsector : H99 Registration Date : 2016-11-16

Page 35 ID : 04000342/0002 04000342 Equipment for commercial kitchens - Portable, non-integrated oil/fat filtration equipment, Requirements and testing Subsector : H99 Registration Date : 2016-11-16 ID : 04000345/0001 04000345 Appareils pour la grande cuisine - Tables de lavage et éviers - Partie 3: Lavabo de main, Exigences et essais Subsector : H99 Registration Date : 2016-11-16 ID : 04000346/0001 04000346 Appareils pour la grande cuisine - Tables de lavage et éviers - Partie 4: Bassin de drain, Exigences et essais Subsector : H99 Registration Date : 2016-11-16 ID : 04000347/0001 04000347 Appareils pour la grande cuisine - Tables de lavage et éviers - Partie 5: Combinaison de lavabo de main et de bassin de drain, Exigences et essais Subsector : H99 Registration Date : 2016-11-16

Page 36 ID : 04000349/0002 04000349 Equipment for commercial kitchens - Thermal equipment - Part 4: Noodle cookers, Requirements and testing Subsector : H99 Registration Date : 2016-11-16 ID : 04000350/0001 04000350 Methods for measuring the energy consumption of commercial kitchen appliances - Part 3: Deep fat fryers Subsector : H99 Registration Date : 2016-11-16 ID : 04000351/0001 04000351 Equipment for commercial kitchens - Convection ovens and convection steamers - Requirements and testing ** End of Sector **

Information procedure Page 37 Monthly Notifications Register Notifications registered at CCMC from 2016-11-01 to 2016-11-30 Sector I : MECHANICAL ENGINEERING Register issued on : 2016-12-05

Subsector I02: FASTENERS Page 38 Subsector : I02 Registration Date : 2016-11-21 ASI Austria ID : 00027001/0001 21.060.10 ÖNORM M 5029 Mechanical fasteners - Panhead tapping chipboard screw - Single start full threaded or part threaded - Cross recess driving form Z and hexalobular internal driving HL This ÖNORM contains requirements for single-start panhead tapping chipboard screw, full threaded or part threaded, driving cross recess, driving form Z according to ÖNORM EN ISO 4757 and hexalobolar internal driving HL according to ÖNORM EN ISO 10664, for thread sizes SP3,0 to SP6,0 and nominal lengths of 10 mm to 100 mm, used outside areas liable to registration such as load bearing timber wood constructions. Subsector : I02 Registration Date : 2016-11-21 ASI Austria ID : 00027003/0001 21.060.10 ÖNORM M 5027 Mechanical fasteners - Chipboardscrews - Full threaded or part threaded - Cross recess driving form Z and hexalobolar internal driving HL This ÖNORM contains requirements for single-start chipboardscrews, full threaded or part threaded, driving cross recess, driving form Z according to ÖNORM EN ISO 4757 and hexalobolar internal driving HL according to ÖNORM EN ISO 10664, for thread sizes SP3,0 to SP10,0 and nominal lengths of 10 mm to 400 mm, used outside areas liable to registration such as load bearing timber wood constructions. Subsector : I02 Registration Date : 2016-11-21 ASI Austria ID : 00027004/0001 21.060.10 ÖNORM M 5028 Mechanical fasteners - Raised countersunk head chipboard screw - Single start full threaded or part threaded - Cross recess driving form Z and hexalobular internal driving HL This ÖNORM contains requirements for single-start raised countersunk head chipboard screw, full threaded or part threaded, driving cross recess, driving form Z according to ÖNORM EN ISO 4757 and hexalobolar internal driving HL according to ÖNORM EN ISO 10664, for thread sizes SP3,0 to SP6,0 and nominal lengths of 10 mm to 100 mm, used outside areas liable to registration such as load bearing timber wood constructions.

Page 39 Subsector I05: IRON PIPES Subsector : I05 (Secondary Subsector) Registration Date : 2016-11-25 TSE Turkey ID : t1002649/0001 23.040.40, 91.140.10 Steel pipe fittings - Welding ended, threaded or flanged This standard covers the connection parts welded to pipes used for general purposes and the connection parts made of steel and flanged to pipes Subsector I06: PRESSURE VESSELS Subsector : I06 Registration Date : 2016-11-29 UNI Italy ID : 01602195/0001 23.020.30, 27.060.30 UNI1602195 Pressure equipment - Putting into service and use of pressure equipment and assemblies -Part3:Supervisionofsteamboilersand/orsuper-heatedwatergenerators This technical specification provides procedures for the supervision of pressure equipment with the risk of overheating intended for generation of steam and/or super-heated water at temperatures higher than 110 C ( steam boilers and/or hot water generators ) at a maximum allowable pressure PS greater than 0,5 bar included in the scope of the Italian decree D.M. 329/2004. The technical specification gives recommendations of operation and testing of the boiler both with and without the continuous presence of the boiler attendant, with a maximum time of operation without manual intervention of 72 hours. REV/AMD UNI/TS 11325-3:2010 Subsector I08: AGRICULTURAL MACHINES Subsector : I08 Registration Date : 2016-11-21 ASI Austria ID : 00027002/0001 53.020.99, 65.060.99

Page 40 ÖNORM L 5277 Pulley block in agriculture and forestry This ÖNORM determines the required information on the pulley and the design parameters for pulley block in agriculture and forestry. Subsector I15: EQUIPMENT FOR PETROLEUM INDUSTRY Subsector : I15 Registration Date : 2016-11-04 BSI Draft Issue Date : 2016-08-10 United Kingdom Latest Date for Comments : 2016-10-11 ID : 01601844/0001 Draft for public enquiry PD 8010-1:2015+A1 Pipelinesystems.Part1.Steelpipelinesonland.Codeof practice. Amendment Subsector : I15 Registration Date : 2016-11-04 BSI Draft Issue Date : 2016-08-10 United Kingdom Latest Date for Comments : 2016-10-11 ID : 01601845/0001 Draft for public enquiry PD 8010-2:2015 Pipelinesystems.Part2.Subseapipelines.Codeofpractice. Amendment Subsector I28: FLUID POWER Subsector : I28 Registration Date : 2016-11-16 ID : 06003698/0001 06003698 Hydraulic fluid power - Hose assemblies - Dimensions, requirements

Subsector I31: VALVES Page 41 Subsector : I31 Registration Date : 2016-11-25 TSE Turkey ID : t1002649/0001 23.040.40, 91.140.10 Steel pipe fittings - Welding ended, threaded or flanged This standard covers the connection parts welded to pipes used for general purposes and the connection parts made of steel and flanged to pipes ** End of Sector **

Information procedure Page 42 Monthly Notifications Register Notifications registered at CCMC from 2016-11-01 to 2016-11-30 Sector M : METALLIC MATERIALS Register issued on : 2016-12-05

Subsector M05: WELG Page 43 Subsector : M05 Registration Date : 2016-11-29 UNI Italy ID : 01602412/0001 23.040.20, 25.160.10 UNI1602412 Quality requirements for welding of polyethylene pipes for gas, water and other pressure fluids pipelines The standard defines the quality requirements for the welding of pipes for gas, water and other fluids with pressure, independently by the welding process used. The standard also gives a guideline for the manufacturer assessment to produce welded components in accordance with the requirements established REV/AMD UNI 11024:2003 Subsector : M05 Registration Date : 2016-11-11 AENOR Spain Latest Date for Comments : 2016-12-21 ID : P0047074/0001 Draft for public enquiry PNE 14618 Weld construction inspectors. Qualification and certification. This standard specifies the requirements for qualification and certification of Welding Inspectors, ICS. This standard is independent from the type of welded structure. Any structure, piece, assembly or subassembly having welds during design, fabrication or repairing is considered as a welded structure. REV/AMD UNE 14618:2000 Subsector M15: METALLIC CORROSION Subsector : M15 Registration Date : 2016-11-16 ID : 03200789/0001 03200789 Field coating materials for corrosion protection of buried pipelines - Part 2: Application and quality control on site Subsector : M15 Registration Date : 2016-11-16

ID : 03200791/0001 03200791 External corrosion protection of buried pipes - Part 1: corrosion protection systems for steel pipes Page 44 ** End of Sector **

Information procedure Page 45 Monthly Notifications Register Notifications registered at CCMC from 2016-11-01 to 2016-11-30 Sector N : NON-METALLIC MATERIALS Register issued on : 2016-12-05

Subsector N01: PAPER AND BOARD Page 46 Subsector : N01 Registration Date : 2016-11-16 ID : 07400269/0001 85.080.30 54608 Board - Buckling resistance of corrugated board Subsector : N01 Registration Date : 2016-11-25 TSE Turkey ID : tst11668/0004 85.080 Paper towels This standard specifies description types and characteristics, sampling and testing and with marking of paper towels made of tissue paper. Subsector N02: SOLID FUELS Subsector : N02 Registration Date : 2016-11-25 TSE Turkey ID : ts104341/0001 73.040 Hard coal Taşkömürü Subsector N03: PETROLEUM PRODUCTS Subsector : N03 Registration Date : 2016-11-25 TSE Turkey ID : t2011796/0001 75.100

Page 47 Lubricants, industrial oils and related products (Class L) -Lubricants for compressors (Family D) - For air and gas compressors and vacuum pumps This standard specifies requirements and test methods for lubricants for air and gas compressors and vacuum pumps. Subsector N09: PLASTICS Subsector : N09 Registration Date : 2016-11-16 ID : 05401566/0001 83.080.01 53497 Testing of Plastics - Hot Storage Test on Mouldings Made of Thermoplastic Moulding Materials without External Mechanical Stressing Subsector : N09 Registration Date : 2016-11-16 ID : 06235018/0001 83.100 53428 Testing of cellular materials - Determination of the resistance to liquids, vapours, gases and solid materials Subsector : N09 Registration Date : 2016-11-18 TSE Turkey ID : tst10883/0001 83.080.20 Siding - Rigid polyvinyl chloride This standard covers extruded homogeneous single - wou siding manufactured from rigid PVC compund. International : Modified ASTM D 3679:2013 Subsector : N09 Registration Date : 2016-11-25

TSE Turkey Page 48 ID : tst97298/0001 13.030.99, 83.080.01 Plastics - Assessment of oxobiodegradability of polyolefinic materials in the form of films - Methodology and requirements This standart provides a methodology for the experimental evaluation of the oxobiodegradability of polymeric materials in the form of films. It also prescribes requirements for such materials to qualify as oxobiodegradable. It applies to polyolefin (polyethylene, polypropylene) films of thickness less than or equal to 250 mm which, in the end, may be accidentally dispersed in the environment. European : Identical to AFNOR AC T51-808:2012 Subsector N14: PLASTICS PIPES Subsector : N14 Registration Date : 2016-11-21 ASI Austria ID : 00026994/0001 23.040.20, 93.025, 93.030 ÖNORM B 5161 Plastics piping systems for water supply and for drainage and sewerage with or without pressure - Pipes, joints and fittings made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Supplementary requirements to ÖNORM EN 1796 and ÖNORM EN 14364 This ÖNORM is applicable to industrially produced GRP piping systems that meet the basic requirements of ÖNORM EN 1796 and EN 14364. This ÖNORM cannot be used on GRP piping systems that do not comply with ÖNORM EN 14364 and EN 1796. Piping systems according to this ÖNORM are preferably used for the transport of liquids and can, depending on the class of pipe, with an internal pressure greater than 1 PN be used as pressure pipes or with PN 1 as a sewage pipes. These pipes can be either buried in the ground with or without concrete coating or used as gravity pipelines. Subsector : N14 Registration Date : 2016-11-21 ASI Austria ID : 00026998/0001 93.020 ÖNORM B 5150 Potable water storage tanks and water collection pits made of glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) This Austrian Standard provides a normative basis for the design and the requirements of drinking water tanks made of glass-reinforced thermosetting plastics (GRP). Especially the hygienic requirements (in accordance with ÖNORM B 5014-1 and the German KTW) are

Page 49 taken into account. Further requirements for the mechanical properties of potable water tanks made of glass-reinforced thermosetting plastics (GRP) and for the design and construction are given. Also data concerning internal production control and audit testing (the latter informative) are included. Subsector : N14 Registration Date : 2016-11-18 TSE Turkey ID : t0113670/0001 23.040.01 Rigid polyvinylchloride plastic pipes used for water wells - Column pipes This standard covers rigid polyvinylchloride plastic pipes used for water wells of Column pipes Subsector N99: UNDETERMINED Subsector : N99 Registration Date : 2016-11-18 TSE Turkey ID : t0097284/0001 73.080 Ulexite - Used for industry Üleksit - Sanayide kullanılan ** End of Sector **

Information procedure Page 50 Monthly Notifications Register Notifications registered at CCMC from 2016-11-01 to 2016-11-30 Sector S : HEALTH, ENVIRONMENT AND MEDICAL EQUIPMENT Register issued on : 2016-12-05

Subsector S01: ACOUSTICS AND SOUND INSULATION Page 51 Subsector : S01 Registration Date : 2016-11-16 ID : 00100984/0001 00100984 Prediction of sound propagation Subsector S04: PROTECTIVE CLOTHING AND EQUIPMENT Subsector : S04 Registration Date : 2016-11-04 BSI United Kingdom ID : 01603236/0001 BS 6366:2011+A1 Specification for studs for rugby football boots. Amendment Subsector S05: DENTISTRY Subsector : S05 Registration Date : 2016-11-16 ID : 01402234/0001 11.060.20 19405 Dentistry - High temperature sintering furnace - Test method for temperature measurement with separate thermocouple Subsector S06: VIBRATION & SHOCK Subsector : S06 Registration Date : 2016-11-16 ID : 13202827/0001 21.160

Page 52 95413 Wire rope isolators - Dimensions, sizes Subsector S09: WATER QUALITY AND WATER SUPPLY Subsector : S09 Registration Date : 2016-11-16 ID : 00300651/0001 13.060.20 3505 Controllable backflow preventer with reduced pressure zone - Family B Type A according to EN 12729 for temporary connection to standpipes installed outside of buildings Subsector S20: WASTE COLLECTION, HANDLING AND TRANSPORTATION Subsector : S20 Registration Date : 2016-11-21 ASI Austria ID : 00026997/0001 13.030.40 ÖNORM S 2102 Potential hazards of wastes during storage and treatment The present ÖNORM describes the potential hazards of waste in storage, treatment and specifies the requirements to reduce potential hazards. Subsector S24: SOIL QUALITY Subsector : S24 Registration Date : 2016-11-03 NEN Netherlands ID : 50002010/0001 13.080.05 NTA 8240:2016 Concept nl Soil - Sample treatment of dry soil or wet sediments for the analyses of heavy metals and arsenic - Extraction with calcium chlorid NTA 8240 describes the sample treatment for the analyses of heavy metals and arsenic.

Page 53 Subsector S27: WASTE - CHARACTERIZATION, TREATMENT AND STREAMS Subsector : S27 (Secondary Subsector) TSE Turkey Registration Date : 2016-11-25 ID : tst97298/0001 13.030.99, 83.080.01 Plastics - Assessment of oxobiodegradability of polyolefinic materials in the form of films - Methodology and requirements This standart provides a methodology for the experimental evaluation of the oxobiodegradability of polymeric materials in the form of films. It also prescribes requirements for such materials to qualify as oxobiodegradable. It applies to polyolefin (polyethylene, polypropylene) films of thickness less than or equal to 250 mm which, in the end, may be accidentally dispersed in the environment. European : Identical to AFNOR AC T51-808:2012 ** End of Sector **

Information procedure Page 54 Monthly Notifications Register Notifications registered at CCMC from 2016-11-01 to 2016-11-30 Sector T : TRANSPORT, MECHANICAL HANDLING AND PACKAGING Register issued on : 2016-12-05

Subsector T01: SHIPBUILG AND MARITIME STRUCTURES Page 55 Subsector : T01 Registration Date : 2016-11-16 ID : 13202637/0001 47.020.10 83408-3 Flaps, weathertight - Part 3: Frame and covers made of aluminium Subsector T02: AEROSPACE Subsector : T02 Registration Date : 2016-11-04 BSI Draft Issue Date : 2016-08-30 United Kingdom Latest Date for Comments : 2016-11-01 ID : 01602521/0001 Draft for public enquiry BS 3TA 11:2009/Amd 1 Specificationforbarandsectionformachiningof titanium-aluminium-vanadiumalloy(tensilestrength900-1160mpa)(limitingruling section 150 mm). Amendment Subsector T03: ROAD VEHICLES Subsector : T03 Registration Date : 2016-11-29 UNI Italy ID : 01602331/0001 43.060.40, 43.180, 75.200 UNI1602331 Requirements of vehicles safety technical center that plays activities of Technical evaluation of used vehicles This standard specify minimum requirements for a vehicles safety technical center that plays activities of Technical evaluation of used vehicles and the evaluation process of vehicle itself. Subsector T20: TRAM- AND RAILWAY ENGINEERING Subsector : T20 Registration Date : 2016-11-16

ID : 08701261/0001 08701261 State of railway vehicles - Basic principles and production technology - Part 6: Welding Page 56 Subsector : T20 Registration Date : 2016-11-16 ID : 08701262/0001 08701262 State of railway vehicles - Basic principles and production technology - Part 9: Measuring ** End of Sector **

Information procedure Page 57 Monthly Notifications Register Notifications registered at CCMC from 2016-11-01 to 2016-11-30 Sector Z : INFORMATION TECHNOLOGY Register issued on : 2016-12-05

Subsector Z99: UNDETERMINED Page 58 Subsector : Z99 Registration Date : 2016-11-16 ID : 04300830/0001 04300830 UIM - Unique Identification Mark - Application standard for very small items using matrix symbols Subsector : Z99 Registration Date : 2016-11-11 AENOR Spain Latest Date for Comments : 2016-12-21 ID : P0041744/0002 Draft for public enquiry PNE 178105 Smart cities. Infrastructures. Universal accessibility in the smart cities. Standardization for inclusion of accessibility and design for all criteria in smart cities Subsector : Z99 Registration Date : 2016-11-11 AENOR Spain Latest Date for Comments : 2016-12-21 ID : P0042497/0002 Draft for public enquiry PNE 178401 Smart cities. Street lighting. Levels, zoning and control arquitecture Standardization of the telecontrol of the street lighting according to the characteristics of the different zones present in a city ** End of Sector **

List of non-electrotechnical subsectors 2011-06 Sector A: Services Subsector Title ISO/TC CEN/TC reference reference A01 Tourist services / 329; CEN/WS ETO A02 Cleaning services / 328 A03 Postal services / 331 A04 Transportation services / 320; CEN/WS 016; CEN/WS SCUTUM A05 Maintenance services / 319 A06 Building and construction services / 330 A07 Translation services / A08 Funeral services / CEN/BT/TF 139 A09 Facility management / 348 A10 Services of Real Estate Agents / CEN/BT/TF 180; 373 A11 Security Services / CEN/BT/TF 167; 391; 384; 370; CEN/WS 044; CEN/CLC/TC 4 A12 Consultancy Services / 395; 381 A13 Expertise Services / 405 A14 Aesthetic Services / 403;409 A99 Undetermined / CEN/WS 002; CEN/WS 004; CEN/WS 037; CEN/WS 039; CEN/WS 041; CEN/WS 051; 375; 374; 376; 385; 404

Sector B: Building and construction Subsector Title ISO/TC CEN/TC reference reference B01 Fire protection 21 70; 72; 191; 192 B02 Structures 59; 98 166; 167; 250; 277; 346; 349; 284; 288; 297; 340 B03 Concrete 71 104; CEN/WS 009 B04 Cement 74; 77 51 B05 Fire tests 92 127 B06 Gypsum / 241 B07 Glass 160 129 B08 Doors and windows 162 33 B09 Thermal matters 163 88; 89; 371; CEN/BT WG 173; CEN/WS 036 B10 Timber structures 165 124 B11 Metal structures 167 135 B12 Masonry 179; 196 125; 246 B13 Solar energy 180 312 B14 Geotechnics 182 341; 396 B15 Sanitary appliances / 163; 7 B16 Taps / / B17 Lighting equipment and lighting / 50; 169 application technology B18 Scaffolding / 53 B19 Ceramic tiles 189 67 B20 Drainage equipment / 165 B21 Baths / / B22 Wallcoverings / 99 B23 District heating / 107 B24 Auxiliary and handicraft work / / B25 Gas distribution installation and / 234; 235; 282 related equipment B26 Road building and maintenance / 178; 227 B27 Waterproofing materials / 128; 254; 361; 314 B28 Floor coverings 38/SC 12 134 B29 Aggregates / 154 B30 Floor and surfacing / 217; 303; 323; 390 B31 Heating systems in buildings / 228; 247 B32 Precast concrete products / 177; 229

B33 Building design 205 315; 325; 388 B34 Building and construction Environmental aspect 350; 351 B99 Undetermined / /

Sector C: Chemicals, chemical engineering and food products Subsector Title ISO/TC CEN/TC reference reference C01 Food products 34 174; 275; 302; 360; 307; 327; 338; 387; CEN/WS 008; CEN/WS 018; CEN/WS 054 C02 Paints and related products 35 139; 298; 173 C03 Chemistry 47 317; 363 C04 Laboratory glassware 48 332 C05 Lac / / C06 Essential oils 54 / C08 Pesticides 81 / C09 Surfactants 91 276 C10 Starch 93 / C11 Tobacco 126 401 C12 Glass plant / / C13 Fertilizers 134 223; 260 C16 Wood preservatives / / C17 Trees and plants / / C18 Adhesives / 193 C19 Chemical analysis 201; 202 382; 347 C20 Explosives and firework / 212; 321 C21 Cosmetics 217 392 C22 Bio-Based products / 411 C99 Undetermined / 386

Sector F: Fundamental standards Subsector Title ISO/TC CEN/TC reference reference F01 Technical drawings 10 / F02 Units & symbols 12 / F03 Preferred numbers 19 / F04 Sieves 24 / F05 Measuring instruments 30; 113 92; 171; 176; 237; F06 Terminology principles 37 / 294; 318; 244; 367; 141; CEN/WS 011 F07 Documentation and information 46 304; CEN/WS 024 CEN/WS 010 CEN/WS 023 CEN/WS 028 CEN/WS 014 CEN/WS 050 CEN/WS 006 368 F08 Surfaces / 290 F09 Banking 68 / F10 Statistics 69 / F12 Information processing systems 204 224; 225; 251; 278; CEN/WS CPF CEN/WS CIS CEN/WS ODR CEN/WS CID 287; 311; 365 F13 Environmental tests / / F14 Graphical technology, 130 / sign-boards and nameplates F15 Material testing in general 135 138; CEN/WS 007 CEN/WS 021 CEN/WS 033 F16 Graphical symbols 145 / F17 Administrative documents 154 CEN/WS MMU F18 Micrographics 171 / F19 Optics 172; 187 123; 170 F20 Quality assurance 176 CEN/CLC/TC1 CEN/CLC/WG QS CEN/WS 030 362 F21 Value analysis and project / 279 network F22 Logistics / 379; 273 F23 Energy 203 CEN/CLC/JWG 1; CEN/CLC/JWG 2;

CEN/CLC/JWG 3; CEN/CLC/JWG 4; CEN/WS 027 F99 Undetermined / 389; CEN/WS 057; CEN/WS 058; CEN/WS 060

Sector H: Products for household and leisure use Subsector Title ISO/TC CEN/TC reference reference H01 Cinematography 36 372 H02 Photography 42 / H03 Consumer questions / 291 H04 Sports equipment 83 136 H05 Oil and gas burners / 47; 131 H06 Horology 114 / H07 Space heating 116 62; 110; 130; 179; 180 H08 Sizing systems 133; 137 / H09 Furniture 136 207 H10 Sewing machines 148 / H11 Heater controls 161 58 H12 Ceramic and glass-ware for food 166 / H13 Jewellery 174 CEN/WS 047 H14 Caravans 177 245 H15 Toys 181 52 H17 Oil stoves / 46 H18 Central heating boilers / 48; 57; 109; 269 H19 Non-electric cookers and barbecues / 49; 281; 295 H22 Smokers lighters and matches / 355; 87 H23 Ladders / 93 H24 Tactile danger warnings / / H25 Large gas appliances / 106; CEN/CLC/JWG FCGA H26 Sealing materials / 108; 208 H27 Educational equipment / / H28 Hunting 191 / H29 Heat pumps / 113 H30 Equipment for children / 252 H31 Dedicated LPG appliances / 181 H32 Culinary utensils 186 194 H33 Footwear (excluding protective / 309 footwear) H34 Child safety / CEN/BT/WG 117 398 H99 Undetermined / 299; 364; 369; 402

Sector I: Mechanical engineering Subsector Title ISO/TC CEN/TC reference reference I01 Screw threads 1 / I02 Fasteners 2 185 I03 Limits & fits / / I04 Rolling bearings 4 / I05 Iron pipes 5 203 I06 Pressure vessels 11 54 I07 Shafts 14 / I08 Agricultural machines 23 144, 334 I09 Small tools 29 213 I10 Splines / / I11 Machine tools 39 142; 143; 145; 255 I12 Pulleys & belts 41 188 I13 Gas containers 58 23; 286 I14 Gears 60 / I15 Equipment for petroleum industry 67 12 I16 Internal combustion engines 70; 192 270 I17 Machinery in general 72; 199 114; 153; 214; 313 (including safety) 271, 337; 399; 397 CEN/WS 025 I18 Mining 82 196 I19 Nuclear energy 85 / I20 Refrigeration 86 44; 182 I21 Chains and chain wheels 100 / I22 Vacuum technology 112 / I23 Pumps 115 197 I24 Industrial fans 117 356 I25 Compressors 118 232 I26 Plain bearings 123 / I27 Earth moving and construction 127; 195 151 equipment I28 Fluid power 131 / I29 Gas cleaning / 195 I30 Air distribution / 156 I31 Valves 153; 185 69; 236; 105 I32 Flanges / 74 I33 Information processing in 184 310 automation I34 Non-ferrous metallic pipes / /

I35 Leisure and recreational machines / 152 I36 Thermoprocessing technology / 186 I37 Printing and paper machines / 198 I38 Leather production, tannery and / 200; 201 related machinery I39 Machines for metal processing / 202; 322 I40 Industrial piping networks / 267 I41 Membrane filters / 272 I42 Potentially explosive atmospheres / 305 I43 Hydrogen energy 197 / I44 Nanotechnologies 229 352 I99 Undetermined / CEN/CLC/JTF PE; CEN/CLC/TC 2; 65, 157; CEN/WS 059

Sector M: Metallic materials Subsector Title ISO/TC CEN/TC reference reference M01 Steel 17 CEN/TC 342; 344; ECISS/TC 6 ECISS/TC 7 ECISS/TC 9 ECISS/TC 10 ECISS/TC 11 ECISS/TC 12 ECISS/TC 13 ECISS/TC 15 ECISS/TC 19 ECISS/TC 20 ECISS/TC 21 ECISS/TC 22 ECISS/TC 23 ECISS/TC 24 ECISS/TC 26 ECISS/TC 27 ECISS/TC 28 ECISS/TC 29 ECISS/TC 5 ECISS/TC 14 ECISS/TC 100 ECISS/TC 102 ECISS/TC 103 ECISS/TC 104 ECISS/TC 105 ECISS/TC 106 ECISS/TC 107 ECISS/TC 108 ECISS/TC 109 ECISS/TC 110 M02 Zinc / 209 M03 Foundry technology, 25 190; ECISS/TC 31 ECISS/TC 111 including cast iron M04 Copper 26 133 M05 Welding 44 121 M06 Dimensions of wrought products / / M07 Manganese and chromium 65 / M08 Light alloys 79 132 M09 Iron ores 102 / M10 Metallic coatings 107 240 M11 Powder metallurgy 119 / M12 Aluminium ores 129 / M13 Ferroalloys 132 / M14 Nickel 155 / M15 Metallic corrosion 156 262; 219

M16 Mechanical tests for metals 164 ECISS/TC 1 ECISS/TC 2 ECISS/TC 101 M17 Heavy metal ores 183 / M18 Metal wire products / ECISS/TC 30; CEN/BT/TF 196; 378; 407 M20 Tin and tin alloys / 220 M21 Precious metals / 283 M22 Lead and lead alloys / 306 M99 Undetermined / /

Sector N: Non-metallic materials Subsector Title ISO/TC CEN/TC reference reference N01 Paper and board 6 172 N02 Solid fuels 27 335; 343;383; CEN/WS 019 N03 Petroleum products 28 19; 336; CEN/WS 038; CEN/WS 061 N04 Refractories 33 187 N05 Textiles 38 189; 248 N06 Rubber 45 218; 366 CEN/WS 003 N07 Sawn timber 55 38; 175 N08 Mica / / N09 Plastics 61 249 N10 Cork 87 / N11 Wood-based panels 89 112 N12 Timber products 99 / N13 Leather 120 289 N14 Plastics pipes 138 155 N17 Fluorspar 175 / N18 Glass-fibre reinforced plastics / / N19 Tapes / 253 N20 Ceramics 206 184 N21 Gaseous fuels and combustible gas 158; 193 238; 408 N22 Feather and related materials / 222 N23 Diamond / 410 N99 Undetermined / /

Sector S: Health, environment and medical equipment Subsector Title ISO/TC CEN/TC reference reference S01 Acoustics and sound 43 126; 211 insulation S02 Transfusion equipment 76 / S03 Syringes 84 / S04 Protective clothing and equipment 94 85; 158; 159; 160; 161; 162; CEN/WS 026; CEN/WS 043 S05 Dentistry 106 55 S06 Vibration & shock 108 231 S07 Anaesthetic and respiratory 121 215 equipment S08 Air quality 146 137; 243; 264; CEN/CLC/JWG CMI S09 Water quality and water supply 147 164; 230; CEN/WS 001 CEN/WS 034 S10 Surgical implants 150 285; CEN/CLC/JWG AIMD S11 Contraceptives 157 / S12 Gas analysis / / S13 Ergonomics 159 122 S14 Prosthetics 168 / S15 Surgical instruments 170 / S16 Aids for the disabled 173 293 S17 Respiratory protective devices / 79 S18 Sterilization of equipment 198 102; 204 S19 First aid equipment and rescue systems / 239 S20 Waste collection, handling and / 183 transportation S21 Laboratory medicine, clinical 194 140; 206; 233; pathology and biosafety 257; 258; 316; CEN/CLC/TC 3; CEN/WS 031; CEN/WS 053; CEN/WS 055 S22 Energy saving / CEN/WS 005 CEN/WS 015 S23 Personal & property protection against aggression/burglary protection / 263 S24 Soil quality 190 345; CEN/WS 032

S25 Chemical disinfectants and / 216 antiseptics S26 Environmental management 207 CEN/TC 406; CEN/WS 040 S27 Waste - Characterization, treatment / 292; 308; and streams CEN/BT/TF 120 S28 Demining / CEN/WS 029 CEN/WS 013 S99 Undetermined / 205; CEN/BT/TF 127 394; 259; 357; 358; 359; 380; 400; CEN/WS PCEC CEN/WS 012 CEN/WS 020

Sector T: Transport, mechanical handling and packaging Subsector Title ISO/TC CEN/TC reference reference T01 Shipbuilding and maritime 8; 188 15; 300 structures T02 Aerospace 20 274; AECMA; ECSS ;377 T03 Road vehicles 22 301; 326 CEN/WS IMA T04 Tyres 31 / T05 Pallets 51 / T06 Metal and plastic containers 52 210; 221; 265; 266; 268; 296 393 T07 Glass containers 63 / T08 Cranes 96 147 T09 Materials handling and 101 148; 149 storage equipment T10 Freight containers 104 119; 280 T11 Steel wire ropes 105 / T12 Industrial trucks 110 150; 324 T13 Lifting chains, hooks and ropes 111 168 T14 Packaging 122 261; 120 T15 Cycles 149 333 T16 Lifts & escalators 178 10; 242 T17 Builders hoists / / T18 Elevating platforms / 98 T19 Road safety / 226; 339 T20 Tram- and railway engineering / 256; / CEN/CLC/WG FPR T21 Packaging machines / 146 T22 Off-road vehicles / 354 T99 Undetermined / CEN/WS TAF

Sector Z: Information technology Subsector Title ISO/TC CEN/TC Z01 Radiocommunication for IT / / Z02 Telephony, telegraphy for IT / CEN/CLC - ETSI Z03 Common O.S.I. activities / CEN/CLC - EWOS Z99 Undetermined / 353; CEN/WS ADN; CEN/WS AUT; CEN/WS BII; CEN/WS CAT; CEN/WS CST; CEN/WS CTC; CEN/WS DFA; CEN/WS DIR; CEN/WS DIS; CEN/WS DPA; CEN/WS DPP; CEN/WS EBE; CEN/WS ECH; CEN/WS ECO; CEN/WS EFI; CEN/WS EMD; CEN/WS ESI; CEN/WS ESR; CEN/WS EUR; CEN/WS FAS; CEN/WS FIN; CEN/WS FS2; CEN/WS FUN; CEN/WS GEN; CEN/WS HIC; CEN/WS ICT; CEN/WS IEC; CEN/WS IHM; CEN/WS INV2; CEN/WS ISD; CEN/WS JXF; CEN/WS KMA; CEN/WS LCT; CEN/WS LTS; CEN/WS MDC; CEN/WS MEE; CEN/WS MES; CEN/WS MET; CEN/WS MLX; CEN/WS MMI; CEN/WS NEA; CEN/WS NOM; CEN/WS ORC; CEN/WS POR; CEN/WS QIS; CEN/WS SAN; CEN/WS SCE; CEN/WS TEX; CEN/WS TWE; CEN/WS UDP; CEN/WS URI; CEN/WS WAC;

CEN/WS XFS; CEN/WS XML; CEN/WS ego; CEN/WS ein; CEN/WS epr

REGISTER OF NEW NATIONAL STANDARDIZATION INITIATIVES NOTIFIED UNDER SUBSECTORS IN THE SCOPE OF CENELEC November 2016 Issued on : 5 December 2016

Page 1 Information Procedure on Standards Notifications registered at CCMC during November 2016 Sector U : GENERAL ELECTROTECHNICAL STANDARDS Register issued on : 5 December 2016

Subsector U99: UNDETERMINED Page 2 Subsector : U99 Registration Date : 2016-11-16 ID : 14900212/0001 14900212 Entertainment technology - Media server Subsector : U99 Registration Date : 2016-11-16 ID : 14900212/0001 14900212 Entertainment technology - Media server ** End of Sector **

Page 3 Information Procedure on Standards Notifications registered at CCMC during November 2016 Sector V : ELECTRONIC ENGINEERING Register issued on : 5 December 2016

Subsector V02: ELECTRICAL MEASURING EQUIPMENT Page 4 Subsector : V02 Registration Date : 2016-11-04 BSI United Kingdom ID : 01602751/0001 BS 7856:2017 Codeofpracticeforspecialdesignandotherfeaturesofalternatingcurrent watthourmetersforactiveenergy(midaccuracyclassesaandb)foruseinthe UK ** End of Sector **

Page 5 Information Procedure on Standards Notifications registered at CCMC during November 2016 Sector W : ELECTRICAL ENGINEERING Register issued on : 5 December 2016

Subsector W08: ELECTRIC CABLES Page 6 Subsector : W08 Registration Date : 2016-11-11 AENOR Spain Latest Date for Comments : 2016-12-11 ID : P0047158/0001 Draft for public enquiry PNE-HD 603-5N:2007/1M Distribution cables of rated voltage 0,6/1 kv. Part 5: XLPE insulated cables unarmoured. Section N: PVC sheathed cables without concentric conductor. (Type 5N) This standard specifies the construction, dimensions and test requirements of un-armoured power cables with XLPE insulation and with circular aluminium conductors in single core cables for rated voltage (U) of 1 kv for fixed installations. The sheathing material shall consistofpvc,typedmv18. REV/AMD UNE-HD 603-5N:2007 Subsector : W08 Registration Date : 2016-11-11 AENOR Spain Latest Date for Comments : 2016-12-11 ID : P0047159/0001 Draft for public enquiry PNE-HD 603-5X:2007/1M Distribution cables of rated voltage 0,6/1 kv. Part 5: XLPE insulated cables unarmoured. Section X: Polyolefin sheathed cables without concentric conductor (Type 5X-1 and 5X-2) This standard specifies the construction, dimensions and test requirements of un-armoured power cables with XLPE insulation and with circular aluminium conductors in single core cables for rated voltage (U) of 1 kv for fixed installations. The sheathing material shall consistofpolyolefin. Thisstandardincludestwotypesofcables: Type5X-1:MinimumclassoffirereactionEca Type5X-2:MinimumclassoffirereactionCca-s1b,d2,a1. REV/AMD UNE-HD 603-5X:2007 Subsector : W08 Registration Date : 2016-11-11 AENOR Spain Latest Date for Comments : 2016-12-11 ID : P0047160/0001 Draft for public enquiry PNE-HD 620-9E:2012/1M

Page 7 Distribution cables with extruded insulation for rated voltages from 3,6/6 (7,2) kv up to and including 20,8/36 (42) kv. Part 9: HEPR insulated single core cables, and single core pre-assembled cables. Section E: Cables with polyolefin compound sheath (types 9E-1, 9E-3, 9E-4 and 9E-5). This standard specifies the construction, dimensions and test requirements of power cables withheprinsulationforratedvoltages(u)from20kvupto30kvforfixedinstallations. Thetypesofcablecoveredbythissectionare: Type9E-1:Cablewithpolyolefincompoundsheath,withoutpropertiesincaseoffire. Type 9E-3: Bundle assembled cables (type 9E-1) with steel messenger core for overhead distributionandservice Type 9E-4: Cable with polyolefin compound sheath, low content halogen and special propertiesagainstfirereaction.minimumclassoffirereactioneca. Type 9E-5: Cable with polyolefin compound sheath, low content halogen and special propertiesagainstfirereaction.minimumclassoffirereactioncca-s1b,d2,a1. REV/AMD UNE-HD 620-9E:2012 Subsector : W08 Registration Date : 2016-11-11 AENOR Spain Latest Date for Comments : 2016-12-11 ID : P0047161/0001 Draft for public enquiry PNE-HD 620-10E:2012/1M Distribution cables with extruded insulation for rated voltages from 3,6/6 (7,2) kv up to and including 20,8/36 (42) kv. Part 10: XLPE insulated single core, and single core preassembled cables. Section E: Cables with polyolefin compound sheath (types 10E-1, 10E-3, 10E-4 and 10E-5). This standard specifies the construction, dimensions and test requirements of power cables withxlpeinsulationforratedvoltages(u)from10kvupto30kvforfixedinstallations. Thetypesofcablecoveredbythisstandardare: Type10E-1:Cablewithpolyolefincompoundsheath,withoutpropertiesincaseoffire. Type 10E-3: Bundle assembled Type 10E-1 cables, with steel messenger core for overhead distributionandservice Type 10E-4: Cable with polyolefin compound sheath, low content halogen and special propertiesagainstfirereaction.minimumclassoffirereactioneca. Type 10E-5: Cable with polyolefin compound sheath, low content halogen and special propertiesagainstfirereaction.minimumclassoffirereactioncca-s1b,d2,a1. REV/AMD UNE-HD 620-10E:2012 Subsector : W08 Registration Date : 2016-11-11 AENOR Spain Latest Date for Comments : 2016-12-11 ID : P0047162/0001 Draft for public enquiry PNE 211620 Distribution cables with extruded insulation, of rated voltage from 3.6 / 6 (7.2) kv up to 20.8 / 36 (42) kv inclusive. Single core and single core with XLPE insulation assembled cables. Cables with aluminium tape screen and polyolefin compound cover (types 10E-6, 10E-8 and 10E-9) This standard specifies the construction, dimensions and test requirements of power cables

withxlpeinsulationforratedvoltages(u)from10kvupto30kvforfixedinstallations. Thetypesforcablecoveredbythisstandardare: Type10E-6:Cablewithpolyolefincompoundsheath,withoutpropertiesincaseoffire. Type 10E-8: Cable with polyolefin compound sheath, low content halogen and special propertiesagainstfirereaction.minimumclassoffirereactioncca-s1b,d2,a1. Type 10E-9: Bundle assembled type 10E-6 cables, with steel messenger core for overhead distribution and service. Page 8 Subsector W27: ELECTRICAL INSTALLATIONS IN BUILGS Subsector : W27 Registration Date : 2016-11-16 ID : 02227128/0001 02227128 Low-voltage electrical installation - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances (IEC 64/2123/CDV:2016) Subsector : W27 Registration Date : 2016-11-16 ID : 02227156/0001 02227156 Low-voltage electrical installation - Selection and erection of electrical equipment - Switches and socket-outlets ** End of Sector **

Page 9 Information Procedure on Standards Notifications registered at CCMC during November 2016 Sector Z : CCMC/CEN/CLC Register issued on : 5 December 2016