INSTALLATION INSTRUCTIONS 5000 700069 50055 MODEL: Dillon 5000 (RH-600) 50055 (RH-600X) 700069 (TRRH-600) REV D
Restoration Hardware Faucet Product Size Specification Diagram Recommended Deck Hole Size -/8 Diameter Dimensions are in Inches and Approximation of a Typical Installation Technical support: -866-7-507 Customer Service: -877-77-67 RH-600 REV D
Common tools needed: Adjustable Wrench Plumbers Putty Pipe Cutter Assorted Screwdrivers Thread Sealant. Installation Instructions We Recommend Installation by a Licensed Plumbing Professional Spout Assembly Insert SHANK () and HOSE () through ESCUTCHEON () and sink hole, (apply putty or silicone to underside of ESCUTCHEON ()). Align SPOUT () and secure into place with MOUNTING BRACKET (5) and NUT (6). SINK HOLE Technical support: -866-7-507 Customer Service: -877-77-67 RH-600 REV D
. Valve Assembly Place flange NUT () and INVERT FLANGE NUT() onto valve BODY (). -5/6 Insert valve BODY () through sink hole from underside of sink. Valve BODY () should extend - 5/6 above mounting surface. If necessary adjust lower flange NUT () and QUICK CONNECT SPACER (). Set valve BODIES (,A) so that their outlets are facing parallel with the spout and tighten upper flange NUT (). A. Hose and Valve Assembly Connect Larger COUPLING NUT () to outlet of each VALVE BODY (, A). Connect Larger COUPLING NUT (5) to T-VALVE (6). Hand tighten and secure each connection with a wrench / turn. A Technical support: -866-7-507 Customer Service: -877-77-67 RH-600 REV D
. Make Water Supply Connections NOTE: SUPPLY RISERS MUST BE PURCHASED SEPARATELY Connect water supply to VALVE BODIES(, A) with one of the three following types of risers: A a. b. c. / IPS FLEXIBLE RISER (), discard RUBBER NOSECONE (7), FRICTION WASHER () and COUPLING NUT (). /8 or / O.D. BULLNOSE RISER (5), place FRICTION WASHER () and COUPLING NUT () onto BULLNOSE RISER (5). / O.D. COPPER RISER (6), place COUPLING NUT (), FRICTION WASHER (), and RUBBER NOSECONE (7) onto end of COPPER RISER(6). Use adjustable wrench to tighten connections. Do not over tighten and be careful not to kink copper supply when bending. Use a tube bender and cutter to properly adjust copper supply. a 5 6 7 b c 5 Technical support: -866-7-507 Customer Service: -877-77-67 RH-600 REV D
5. Install Handles Turn VALVE STEM () to OFF position. Place ESCUTCHEON () and O-RING (6) over CARTRIDGE (5). Secure HANDLE () into place by first engaging the STEM () then thread BONNET () with HANDLE () onto CARTRIDGE (5). Any adjustments for rotatioinal alignment must be made to the valve body, not to the CARTRIDGE (5). 6 5 6 Technical support: -866-7-507 Customer Service: -877-77-67 RH-600 REV D
6. Install Pop- up Drain Remove drain FLANGE (), WHITE WASHER () and PLUNGER ASSY (), and discard drain CAP (), from drain assembly. Place drain FLANGE () and WHITE WASHER () in place through the sink drain hole. (Clear silicone may be used in place of the WHITE WASHER). From underside of the sink install LOCK NUT (8), FLAT WASHER (7), RUBBER CONE WASHER (6), and install drain BODY (9) with the side port pointing toward the back. Cone portion of WASHER (6) to face upward. Secure in place by threading the drain FLANGE () onto drain BODY (9). Then tighten LOCK NUT (8) firmly. ** Adjust drain BODY (9) alignment, as required, by loosening LOCK NUT (8), rotate assembly for alignment of ball ROD () to pop-up ROD (0) and re-tighten LOCK NUT (8). Apply thread sealant to TAILPIECE (5) and attach to drain BODY (9). Attach TAILPIECE (5) to p-trap drain (not included). See Figure. Place PLUNGER ASSY(), oriented as shown, into drain FLANGE (). Insert pop-up ROD (0) through spout and secure to STRAP (6), approximately " from end of ROD (0), with SCREW (7). Insert ball ROD () into the drain's side port opening and connect it with the bottom hole of PLUNGER ASSY (), secure with ball rod NUT (). Adjust the height of the drain cap of PLUNGER ASSY () through elevation holes in STRAP (6). Use CLIP (5) to secure ball ROD () to STRAP (6). Adjust ball ROD () and pop-up ROD (0) adjusting via the elevation of the STRAP (6) so drain will open and close properly. See Figure. Figure Note hole orientation SINK HOLE 6 7 8 9 5 P-TRAP DRAIN 7 Technical support: -866-7-507 Customer Service: -877-77-67 RH-600 REV.D
Figure 0 Note hole orientation 7 6 5 Blue washer in this end 9 White washer inside the body Figure 0 6 Extension Kit #5 (not supplied) MIN 7 MAX Note: Extension Kit (# 5) for ball ROD () and/or pop-up ROD (0) available (sold separately). See Figure for nominal dimensions. (Extension Kit connection must not interfere with CLIP (5), cutting item () and/or (0) may be required.) 8 Technical support: -866-7-507 Customer Service: -877-77-67 RH-600 REV.D
7. Test Installed Faucet With handles in OFF position, turn on water supplies and check all connections for leaks. Operate both handles to flush water lines thoroughly. Operate pop-up drain assembly and check for leaks. If water flow is diminished, clean flow restrictor by disassemble T-VALVE (6) IN figure. Care and Cleaning The lustrous finish on your Restoration Hardware Bathware fixture should be treated with care. Improper handling or cleaning can damage the surface of any metal finish. Use a soft cloth to wipe clean. Avoid harsh abrasive cleaner. Water contains lime and other mineral deposits that will be left on the surface after the water has evaporated. You can prevent these deposits from forming by always wiping the fixture dry immediately after use. Technical Support and Customer Service For technical support in the installation of your Restoration Hardware Bathware fixture, please call -866-7-507 weekdays between the hours of 7:00am and :00pm PST. For other questions regarding your order, to order additional components of the Restoration Hardware Bathware Collection, to order replacement parts, or to address warranty issues, please contact Restoration Hardware Customer Service at -877-77-67. 9 EN-98 RH-600 REV.D