Project: Type: Model# CDL8 LED Architectural PRODUCT DESCRIPTION Retrofit Down lights The Luminoso 8 inch Commercial LED Downlight is damp rated, and suitable for 1-277V Input equipped with fire-rated Junction box. The CPL delivers high lumen output while maintaining an 85+ CRI. With a lifetime greater than 5, hours, the Luminoso CDL is suitable for nearly all commercial downlight applications providing K, 4K, 5K color temperature options. It can replace most manufacturers' incandescent, CFL or H.I.D. fixtures with apertures of 8.1" minimum to 8.7" maximum diameter. PERFORMANCE SUMMARY Efficancy: >9 Lm/W Power: 18W, 23W, 27W, 4W, Delivered light output: 1438-41 lumens Chip: CREE COB by Cree True White Technology CRI: Ra>85 CCT Options: K 4K 5K THD: <2% Power Factor: >.9 Standard Warranty: 5 Years Standard Lifetime: Designed for minimum 5, hours Dimmable: - 1V The external driver ensures steady performance and long lifespan Driver efficiency >87%. Temperature Rating: Designed to operate in temperatures of 45 C and below room side and plenum side. REGULATORY & VOLUNTARY QUALIFICATIONS UL Listed Energy Star Listed Suitable for damp locations. LED Chip The Luminoso LED CDL delivers superior quality light output using Cree's Chip on Board technology. LED sources have been LM8 tested and reported from accredited testing laboratories in accordance with IESNA LM-8-28. Standard color management maintains superior color consistency over time and various climates. CCT classification according with the ANSI C78.377-28 standard. Heat Sink Luminoso innovative heat sink mounted to tail enables the LEDs to consistently run cooler, providing significant boosts to lifetime, efficacy, and color consistency. Optical System The reflector is made of surface oxidized metal, which effectively enhances the lumen output ratio. Also, the interior surface fish scale design prevents lighting glare, creating an even light effect free from layering. ORDER INFORMATION EXAMPLE: CDL8-19--5K-P-Y Enter Information: Series Base Wattage CCT Optics Voltage Options CDL8 19=Whip 18W K = K P=4º Y=12-277V Blank = None 23W 27W 4W 4K = 4K 5K = 5K EB = Emergency Battery Backup 9.8.16 Rev.3 1
CDL8 Performance Series / Performance Series No. Power Lumens Efficacy CRI Input CDL8-18W CDL8-23W CDL8-27W CDL8-4W 18W 23W 27W 4W 1438 Lm 177 Lm 222 Lm 288 Lm 9 Lm/W 9 Lm/W 9 Lm/W 9 Lm/W 85 85 85 85 12-277V DC 12-277V DC 12-277V DC 12-277V DC CDL8-41 Lm 9 Lm/W 85 12-277V DC Photometrics 18W 23W 27W 6 12-6 18 6 24 C/18,4.deg C9/27,39.6deg 7 14-6 21 6 28 C/18,39.2deg C9/27,39.8deg 7 14-6 21 6 28 C/18,39.2deg C9/27,39.8deg 4. 4.2 39.6 39.7 39.88 7. 69.6 69.5 69.8 69.73 39.2 39.1 39.8 4.1 39.2 69.5 69.7 7.2 69.8 39.8 39.1 38.9 4. 4.1 39.53 69.7 69.7 7. 7.1 69.88 4W 11 22-6 3 6 44 C/18,39.deg C9/27,39.8deg 12 24-6 36 6 48 C/18,46.8deg C9/27,47.1deg 39. 38.7 39.8 39.9 39.35 69.8 69.8 7. 69.9 69.88 46.8 46.9 47.1 47. 46.95 78.1 78.3 78.7 78.3 78.35 9.8.16 Rev.3 2
Photometrics 18W Angle:39.4.Flux out:1354.lm. 23W Angle:39.4.Flux out:1354.lm. 27W Diameter Height ( m) Eavg(lx) Emax(lx) Height ( m) Diameter Eavg(lx) Emax(lx) Angle:39.4.Flux out:1354.lm. Height ( m) Diameter Eavg(lx) Emax(lx).5 36.3 6466 1323..5 36. 7983. 12729..5 35.9 124. 1635. 1. 72.6 1616 2581. 1. 72. 1996. 3182. 1. 71.8 256. 49. 1.5 18.9 718.4 1147. 1.5 18. 887. 1414. 1.5 17.7 1114. 1782. 2. 145.2 44.1 645.2 2. 144. 498.9 795.6 2. 143.6 626.5 12. 2.5 181.5 258.6 412.9 2.5 18.1 319.3 59.2 2.5 179.6 41. 641.4 3. 217.8 179.6 286.7 3. 216. 221.7 353.6 3. 215.4 278.4 445.4 3.5 254.1 131.9 21.7 3.5 252. 162.9 259.8 3.5 251.3 24.6 327.2 4. 29.4 11. 161.3 4. 288. 124.7 198.9 4. 287.2 156.6 25.5 4.5 326.7 79.8 127.4 4.5 324. 98.6 157.2 4.5 323.1 123.8 198. 5. 363. 64.7 13.2 5. 36.2 79.8 127.3 5. 359.3 1.2 16.3 4W Angle:39.4.Flux out:1354.lm. Height (m) Diameter Eavg(lx) Emax(lx) Angle:39.4.Flux out:1354.lm. Height (m) Diameter Eavg(lx) Emax(lx).5 35.8 115. 2849..5 43.5 13661. 2242. 1. 71.6 3254. 5212. 1. 87. 3415. 565. 1.5 17.4 1446. 2317. 1.5 1.4 1518. 2491. 2. 143.2 813.5 13. 2. 173.9 853.8 141. 2.5 179. 52.6 834. 2.5 217.4 546.4 896.8 3. 214.8 361.5 579.1 3. 26.9 379.5 622.8 3.5 25.6 265.6 425.5 3.5 4.4 278.8 457.6 4. 286.4 23.4 325.8 4. 347.9 213.4 35.3 4.5 322.3 16.7 257.4 4.5 391.3 168.6 276.8 5. 358.1 1.2 28.5 5. 434.8 136.6 224.2 Recommend Dimmers for DC: Leviton cat,nos: AW RMG-7XX AW SMG-7XX AW SMT-7XX IP71-LFZ/DLX www.leviton.com Lutron cat,nos: DIVA-DVTV NOVA-NVTV NOVAT-NTFTV W /PP2 www.lutron.com Dimensions A Item NO: A B CDL8-18W 8.19" 9.29" CDL8-23W 8.19" 9.29" CDL8-27W 8.98" 9.29" CDL8-4W 8.98" 9.29" CDL8-9.76" 9.29" B 9.8.16 Rev.3 3
EMBE Emergency Ballast PRODUCT DESCRIPTION The Luminoso Emergency Battery Back-up allows the LED fixture to be used for both normal and emergency operation. In the event of a power failure, the EMBE switches to the emergency mode and operates the existing fixture for 9 minutes. The LED Emergency Battery Back-up is UL recognized and contains a battery, charger and converter circuit in a single can and is available in different mounting configurations for individual fixture requirements. 1.The EMBE-8W-Y is for use with an LED load up to 8W at a rated voltage of 12V-48V. 2.The EMBE--Y is for use with an LED load up to at a rated voltage of 12V-48V. 3.The EMBE--Y is for use with an LED load up to at a rated voltage of 18V-48V. FEATURES 1.Dial the code to suitable rated voltage of luminaire. 2.Recyclable Ni-Cad battery. 3.Includes test switch and charge indicator accessory kit. 4.For use with switched or unswitched fixtures 5.Meets or exceeds all National Electrical Code and Life Safety Code Emergency Lighting TECHNICAL SPECIFICATIONS DIAL CODE FOR SUITABLE RATED VOLTAGE OF LUMINAIRE EMBE--Y Model(UL) EMBE-8W-Y EMBE--Y EMBE--Y Input Voltage 1-277VAC,5-6Hz Input Current 65mA (max) 65mA (max) 8mA (max) Input Power 4.8 Watts(max) 4.8 Watts(max) 6 Watts(max) Output Voltage 12V-48VDC 12V-48VDC 18V-48VDC Max. Connected Load.5 A.75 A 1.4 A Output Power 8W(max) (max) (max) Emergency Operation Battery UL Conditions of Acceptability Model EMBE-8W-Y EMBE--Y Emeregency Power 8W 9 minutes High Temp Nickel-Cadmium; 24 Hour Recharge; 7-1 Year Life Expectancy Must be factory wired Battery temperature must not exceed 5 Switch select Voltage Current 1 12-16V.5A 2 16-24V.33A 3 24-36V.22A 4 36-48V.16A 1 12-16V.75A 2 16-24V.5A 3 24-36V.33A 4 36-48V.25A 1 18-24V 1.4A 2 24-36V.7A 3 36-42V.6A 4 42-48V.52A DIMENSIONS B A TYPICAL WIRING DIAGRAM SMITCH OR UNSWITCH (2) TEST SWITCH Model C EMBE-8W-Y EMBE--Y EMBE--Y A 2.18" 2.18" 2.7" B 2.17" 2.17" 2.8" C 1.4" 1.4" 14.8" D 2.7" 2.18" 2.7" E.9".9".9" AC DRIVER LED LFLEX B Emergency RED(+) BROWN(+) BLUE(-) LFLEX A PURPLE(+) D UNIT CONNECTOR (1) Order Information Example: EMBE-8W-Y CHARGE INDICATOR GRAY(-) BLUE(-) LED ARRAY Product Category Source Voltage EMBE 8W Y = 12-277V (1) DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. (2) TEST ACCESSORY LEADS-OBSERVE PROPER POLARITY WIRING. 6.27.16 Rev.3 4
Installation & Safety IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: Read And Follow All Safety Instructions 1: CAUTION - To prevent electrical shock, do not mate unit connector until installation is complete and A.C. power is supplied to the unit. 2: CAUTION - This fixture provides more than one power supply output source. To reduce the risk of electrical shock, disconnect both normal and emergency sources by turning off the A.C. branch circuit and by disconnecting the unit connector. 3: CAUTION - This is a sealed unit. Components are not replaceable. Replace the entire unit when necessary. 4: CAUTION - Installation and servicing should be performed by licensed electrical contractor. Only de-energize before opening. 5: DO NOT USE OUTDOORS. The LED Emergency equipment is for use with grounded, UL Listed, damp location rated, indoor fixtures. Not for use in heated air outlets or hazardous locations. 6: The LED Emergency requires an unswitched A.C. power source of 1-277 volts. Properly cap the unused A.C. lead. 7: The LED Emergency and A.C. driver must be on the same branch circuit. 8: Do not mount near gas or electric heaters. 9: The LED Emergency should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel. 1: The LED Emergency will supply 48V DC output at the individual rated specification for 9 minutes. See individual units for output specifications. 11: Suitable for use in damp locations. 12: For use in 32 F minimum, 122 F maximum ambient temperatures. 13: The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 14: Do not use this equipment for other than intended use. 15: Install in accordance with the National Electrical Code and local regulations. 16:Lighting fixture manufacturers, electricians, and end users need to ensure product system compatibility before final installation. SAVE THESE INSTRUCTIONS Installation Instructions CAUTION: Before installing, make certain the A.C. power is off and the LED Emergency unit connector is disconnected. 1. Production Information 2. Mounting The LED Emergency The LED Emergency should be mounted on or nearby the fixture above the ceiling. The flex conduit marked "A" should be wired into the driver/lamp compartment or to an electrical junction box on the fixture which allows access to the fixture connections. Refer to Illustration 1 for typical mounting. When battery packs are remote mounted, the remote distance can not exceed ½ of the distance from driver to lamp specifed by the A.C. driver manufacturer. Under no circumstances should the battery pack exceed a distance of 5' from the lamp. 3. Wiring AC In put 12-25VAC (UL/CUL) 1-277VAC (UL) Refer to the wiring diagram on the back page for the appropriate wiring of the LED load and driver. Install in accordance with the National Electrical Code and local regulations. For additional wiring diagrams consult Customer Service. 4. Mounting The Test Accessories Cut a single gang switch box into the ceiling tile adjacent to the fixture within reach of the LED Emergency flex. After mounting the switch box, connect flex to the box and route all leads inside the box. Note proper polarity of the charge indicator light prior to removal from harness. 5.LABELS Model EMBE-8W-Y EMBE--Y EMBE--Y EMBE-8W-Y EMBE--Y EMBE--Y LED Arrays 8W 8W Attach the appropriate labels adjacent to the Test Switch and Charge Indicator. Annotate Replacement Label for LED array type and wattage. The Caution and the Relamping labels must be on the fixture in a readily visible location to anyone attempting to service the fixture. 6.WIRING THE A.C. INPUT A.The LED Emergency and A.C. driver must be on the same branch circuit. B.When the LED Emergency is used with a switched fixture, the A.C. input to the LED Emergency must be connected ahead of the fixture switch, Refer to Illustration 2 for switched and unswitched fixture wiring diagrams. 6.27.16 Rev.3 5
Installation & Safety Flex A Illustration 1: Downlight Fixture LED Emergency LED Flxture Illustration 2: Switched Fixture SWITCH LED DRIVER Flex B Switch Box TEST SWITCH Unswitched Fixture LED Emergency Junction Box Ceiling Tile Test Accessories TEST SWITCH WH ITE LED DRIVER LED Emergency 7.COMPLETING INSTALLATION When the installation is complete, switch the A.C. power on and join the LED Emergency unit connector. OPERATION Normal Mode- A.C. power is present. The A.C. driver operates the LED load as intended. The LED Emergency is in the standby charging mode. The Charge Indicator will be lit providing a visual indication that the battery is being charged. Emergency Mode- The A.C. power fails. The LED Emergency senses the A.C. power failure and automatically switches to the Emergency Mode. One or multiple LED are illuminated, for a minimum of 9 minutes. When the A.C. power is restored, the LED Emergency switches the system back to the Normal Mode and resumes battery charging. See page 1 of the Instruction Manual. (1)DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. (2)TEST ACCESSORY LEADS-OBSERVE PROPER POLARITY WIRING. Instruction Manual LED Emergency TESTING & MAINTENANCE Pressing the Test Switch turns off the light on the Charge Indicator and forces the unit into emergency mode, interrupting power to the designated A.C. driver. The LED load is now being lit by the LED Emergency unit. After releasing the Test Switch, the fixture returns to normal operation after a momentary delay. To simulate a " OUT" use the circuit breaker to turn off A.C. power. Initial Testing- Allow the unit to charge approximately 1 hour, then conduct a short dis-charge test. Allow a 24 hour charge before conducting a one hour test. The LED Emergency is a maintenance free unit, however, periodic inspection and testing is required. NFPA 11, Life Safety Code, outlines the following schedule: Monthly - Insure that the Charge Indicator light is illuminated. Conduct a second discharge test by depressing the Test Switch. At least one LED should operate at reduced output. Annually - Insure that the Charge Indicator is illuminated. Conduct a full 9 minute discharge test. The unit should operate as intended for the duration of the test. Written records of testing shall be kept by the owner for inspection by the authority having jurisdiction. TYPICAL WIRING DIAGRAM AC DRIVER SMITCH OR UNSWITCH (2) TEST SWITCH RED(+) LFLEX B LED Emergency Brown(+) BLUE(-) LFLEX A PURRLE(+) UNIT CONNECTOR (1) CHARGE INDICATOR GRAY(-) BLUE(-) LED ARRAY 6.27.16 Rev.3 6