Q3200 Smart Home Alarm Kit Content and Installation Guide
Table of Contents 1. Introduction 1 2. Installation 4 3. Troubleshooting & Factory Reset 7 4. Specifications 9 Information and illustrations are subject to change within this document. Blaupunkt reserves the right to alter the specification and product design at anytime without notice.
1. Introduction This document includes information to help you install and maintain your Q3200 alarm system and its accessory devices. For information about registration and system operation using Blaupunkt Home Connect cloud server. Please refer to Blaupunkt Home Connection User Manual which you can download from server home page https://eu.bphomeconnect.com/ Kit Contents Control Panel The Control Panel is the hub of your alarm system. It must be powered on and connected to internet at all times. When an alarm signal is transmitted from accessory devices, the Control Panel will activate its built-in buzzer to raise alarm and report the event to the server, which in turn sends notification to user via email or smartphone push notification. The Control Panel is puposedly designed to resemble the appearnce of a speaker and blend in your home environment. Mode LED Status LED Network LED Learn/Reset Button Switch Ethernet Port DC Jack Status LED (Green / Red): Green ON Disarm Mode Green Flash Learning Mode Red ON Away Arm Mode Red Flash Home Arm Mode Off Walk Test Mode Status LED (Amber / Red): Amber ON System has fault Amber Flash AC failure Red Flash System alarming Red ON Alarm Memory Off Normal Network LED (Amber ): Amber ON Network Error Off Normal Learn/Rest Button: Used for learning new device or resetting panel to default. Switch: Slide to ON to activate and charge built-in battery. DC Jack: Connect the DC9V 1A adaptor supplied in the package to power up Control Panel Ethernet Port: Connect to your router 1
IMPORTANT NOTE: The Switch is set to OFF by factory default. Please make sure to turn the switch to ON after connecting AC power to the Control Panel, otherwise the battery will not be charged and the Control Panel will be without back up power when power fails. It takes about 72 hours to fully charge the battery. When fully charged, the battery can serve as back-up power source for about 15 hours. Accessories All accessories included in the kit content are pre-linked with Control Panel and do not require manual linking (learning). If learning is required, please refer to the the server user manual. Door Contact The Door Contact is mounted on the Door or Window frame to detect door/window opening. When triggered, it will transmit a signal to Control Panel to alert the condition LED Indicator: The LED will light up if the Door Contact is triggered under tamper open or low battery status to signal fault. Learn / Test Button: The Learn / Test button is used to send signal for learning Door Contact or test range. Tamper Switch: The tamper switch is compressed against door or window frame when installed. When the Door Contact is removed from installed location, or its cover opened, the Tamper Switch will be activated. Rib Mark: The Rib Mark marks the location of the Door Contact s internal magnetic switch to help alignment with the magnet. Magnet LED Indicator Learn/Test Button Rib Mark Tamper Switch Magnet The magnet is mounted on the door and window and should align with the Rib mark when installed. PIR Camera The PIR Camera raises alarm upon detecting intruder and takes 3 pictures to send to user for verification. Parts Identification: LED Indicator / Learn & Test Button: The LED will light up if the PIR Camera detects movement under tamper open or low battery status to signal fault. PIR Sensor: The PIR Sensor has a detection coverage of about 90 to the front. LED Indicator / Learn/Test Button PIR Sensor LED Flashlight Camera Lens 2 Tamper Switch
LED Flashlight: The Flashlight provide lighting for image capture under low light condition Camera Lens: The camera lens has coverage of about 60 to the front. Tamper Switch: The tamper switch is located inside the back cover and depressed by bottom screw. It will be activated when the bottom screw is loosened to open back cover. Remote Controller The Remote Controller can be carried with the user to control alarm system mode. You can also use the Panic button on the Remote Controller to activate a Panic alarm at any time regardless of system mode. Parts Identification: LED Indicator: The LED Indicator will light up when the Remote Controller is transmitting signal. Away Arm Button: Press the button to Away Arm the alarm system. Home Arm Button: Press the button to Home Arm the alarm system. Disarm Button: Press the button to Disarm the alarm system Panic Button: Press and hold the button for 3 seconds to activate a Panic alarm. Cover: Insert a coin into the slot and turn counter-clockwise to open the cover and insert battery, then turn clockwise to tighten. Arm Button Emergency Button LED Indicator Disarm Button Home Button Cover System Extension Aside from the devices included in the package, you can further improve the capability of your alarm system by purchasing extra accessories. Such as extra PIR Sensor or Door Contract to extend your protection area; Remote Keypad for a secondary system operation platform; Smoke Detector for fire protection; Temperature Sensor for temperature update; and more Power Switch for energy management and Home Automation. For information about more accessory devices, please visit www.blaupunkt.com 3
2. Installation Before proceeding to install your accessory devices, you should first complete system registration on Blaupunkt Home Connect server. Please refer to the Quick Start Guide or server user manual to complete the registration process and log into your user account. Signal Range and Walk Test All accessory devices in the Q3200 alarm kit uses wireless radio protocol to communicate with the Control Panel to save you from the extra labour of wiring the device to panel. All devices in the alarm system have an approximate range of 30 meters in typical domestic environment. The range may vary depending on different home condition. Before installing an accessory device, you should test its signal range at selected mounting location first. To test signal range, use the Walk Test function from Blaupunkt Home Connection server, then press the device s test button to transmit test signal. Refer to the server user manual for more info. Home Arm Mode Planning The alarm system functions according to its current Mode, which determines the system behaviour when a sensor is activated. There are 3 modes: Disarm Mode: The system will not activate alarm when a Burglar protection sensor, such as Door/Window Contact, or PIR sensor is triggered. It will only activate alarm if the user does so manually, or a Fire/Water sensor is triggered. Away Arm Mode: The system will activate alarm when any sensor is triggered. Home Arm Mode: The system will only activate Burglar alarm from specific sensors. Sensor set to be ignored under Home Arm mode will not be activated alarm when triggered. With Home Arm mode, you can keep your home perimeter under alert, and still be able to move freely within the house. Home Arm mode allows system to be partially armed by deactivating some sensors under Home Arm mode. Before installation, you should plan ahead and determine which sensor should be deactivated for Home Arm mode. Usually the sensor deployed at home perimeter and entry points, such as Door Contact on the front gate, should be activate all the time. While sensors located in internal space, such as 2 nd floor can be deactivate for Home Arm mode. For more info about Home Arm mode setting, please refer to server user manual. Tamper Protection Your intrusion protection sensor (PIR Camera and Door Contact) are protected from sabotage attempt by a tamper switch, which is triggered when the device cover is opened, or removed from mounted surface. When the tamper switch is triggered, the sensor will transmit signal to Control Panel to alert user that the sensor may be either installed improperly or has been sabotaged. To make sure the tamper switch functions properly, please make sure the switch is fully depressed against the mounting surface when installing your accessory devices. General Device Location Guideline Avoid mounting the Control Panel and devices close to large metal objects or electrical interference source, such as fridge and microwave oven as they could affect signal strength. Wall material also plays a great role in signal penetration efficiency, for example, a brick wall will reduce signal strength a lot more than wooden wall. For devices that has tamper protection function, mount on even surface to ensure the tamper is fully closed when mounted. For uneven surface, use extra packing material on the back. 4
Device Location Panning: Door Contact The Door Contact should be mounted as high as possible. Do not aim a PIR sensor directly at this door/window. Remote Controller The Remote Controller is carried with you personally and not installed at fixed location. PIR Camera Mount the PIR Camera at 1.9-2m height for best performance. When mounted at 2m height, the PIR sensor has a range of 12m. PIR Camera detection is most effective when the intruder is moving across its field of view from the sides. Do not mount PIR sensor in a location that faces intruder directly. Do not mount the PIR Camera directly exposed to sunlight, which may affect detection sensitivity. Do not point PIR Camera at window, moving object or sources of heat e.g. fire or boiler. Control Panel The Control Panel should be mounted in a hidden area invisible from outside view. The Control Panel requires Ethernet connect to your router. 5
Mounting Door Contact 1. Pull out the plastic battery insulator on the back to activate battery and power on Door Contact. 2. The Door Contact should be mounted on the door/window frame, while the magnet should be mounted on the door/window aligned with the Rib Mark on the Door Contact. The gap between the Door Contact and the magnet should be no more than 15 mm. 3. Choose to install the Door Contact with either screw or adhesive tape Screw Mounting The Door Contact has two knockouts on the inside of the back cover where plastic is thinner for wall mounting. 4. Open the Door Contact back cover to reveal the knockouts, break through the knockouts and use the knockouts to mark position on door or window frame 5. Drill holes into door or window frame at marked location, insert plugs if needed. 6. Screw the back cover into marked location and replace the front cover. 7. Screw the magnet onto the door, the position of the magnet should be aligned with the rib mark on the Door Contact at the same height. If the magnet cannot be placed at same height of Door Contact, a spacer is provided in the package to increase the magnet height. Adhesive Mounting Door/ Window Knockouts Before mounting with double side adehesive tape, you should clean the mounting location with degreaser and make sure there is no cracked paint or uneven surface. 4. Unpeel the cover on the double side adhisive tape, apply the tape to the back of Door Contact, then apply the Door Contact to door or window frame 5. Use another double side adhesive tape to install the magnet on the door/window. Frame Tamper Switch Insulator PIR Camera The PIR Camera has knockouts on the back where plastic is thinner. The 2 center knockouts are for flat wall mounting, and the 4 side knockouts are for corner mounting. 1. Pull out the plastic battery insulator on the back to activate batteries and power on PIR Camera. 2. Open the PIR Camera back cover, break through the knockouts and use the knockouts to mark position on wall or corner. 3. Drill holes into the wall or corner at marked location, insert wall plugs if needed. 4. Screw the back cover into marked location and replace the front cover. Corner Fixing Knockouts x 4 Insulator Surface Fixing Knockouts x 2 6
3. Troubleshooting & Factory Reset This chapter covers the potential issues you may encounter during system operation, and factory reset function Control Panel Control Panel Fault Orange LED indicates fault in system, When the LED light up, please login to your Blaupunkt Home Connection Server account to check fault events. The possible fault events include: Control Panel / Devices low battery: -- Change device batteries or charge Control Panel battery accordingly. AC power fail: -- Check AC power connection Sensor out of order: -- Check device battery status and conduct Walk Test to confirm if the Control Panel can receive device signal. Device tamper: -- Close the accessory device tamper switch by checking mounted location and cover screw. Interference: -- Perform Walk Test on all your devices to check if Control Panel can still receive their signals. PIR Camera PIR Camera LED flashes when activated: -- PIR is on low battery or tamper switch triggered. PIR does not respond to movement: -- PIR has a built-in 1 minute sleep timer after detecting a movement. PIR will not redetect movement within 1 minute after it is triggered. Please wait for at least 1 minute before testing PIR again. -- exhausted, please change battery. PIR is slow to respond: -- This is normal. PIR has sophisticated false arm filter setting to prevent accidental trigger. It is also less sensitive when walking directly toward it. PIR give false alarm: -- Make sure pets have no access to protected area. -- Make sure the PIR is not pointed at source of heat or moving objects. Door Contact Door Contact LED flashes when activated: -- Door Contact is on low battery or tamper switch triggered. Door Contact does not respond to door/window opening -- Batteries exhausted, please change battery. -- The magnet is too far away from the Door Contact, please check the gap between the magnet and the Door Contact. Reduce the gap and test the Door Contact again. 7
Remote Controller Remote Controller LED glows dimly when any key is pressed -- Remote Controller on low battery. Factory Reset The Factory Reset function will clear all device info and returns all system parameter to default value. After resetting you will need to setup the system by following the instruction in server user manual. 1. Power down Control Panel by disconnecting AC Power and switching off battery switch. 2. Apply AC Power while holding down the button on the back. 3. Keep holding the button for about 5 seconds until the panel emits a long beep and turn on all 3 LEDs. 4. Release button, factory reset is complete. 8
4. Specifications All Devices Environmental Condition -10 C to 40 C, relative humidity 85% non-condensing for Control Panel and all devices. Radio Operation Range About 30m in typical domestic installation, range varies depending on building construction, device location, and environment. Control Panel Siren Output 96 dba sound pressure @ 1m minimum Zones 40 radio devices. Radio Frequency 868MHZ & 2.4 GHz Power Supply DC9V 1A Power Adaptor 4.8V 1100mAH Ni-MH Rechargeable, charge time 72 hours. Backup Time 15 hours PIR Sensor Radio Frequency 2.4 GHz 2 x 1.5V AA alkaline batteries Door Contact Radio Frequency 868MHz 1 x CR2 3V lithium battery Remote Controller Radio Frequency 868MHz 1 x CR2032 3V lithium coin cell 9
Compliance Statement Declaration of Conformity This device complies with the requirements of the R&TTE Directive 1999/5/EC and the following harmonized standards have been applied: Health: EN62479:2010 Safety: EN60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 EMC: EN 301 489-1 V1.9.2:2011 EN 301 489-3 V1.6.1:2013 EN 301 489-17 V2.2.1:2012 Radio: EN 300 328 V1.8.1:2012 EN 300 220-1 V2.4.1:2012 EN 300 220-2 V2.4.1:2012 FCC FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance may void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). Blaupunkt Competence Center Security & Care Azure Security & Care Corporation www.blaupunkt.com 6F., No.1, Lane 250, Sinhu 2nd Rd., Neihu, Taipei 114, Taiwan 10