Ozone Waterfall Foot and Leg Spa Bath Massager A Tradition for Foot Reflexology Instruction Manual Model: KH298 This user manual provides both operation information of this product and its detailed specifications. Read this manual and understand it thoroughly before operation.
*** Keep this manual for future reference *** READ AND SAVE IMPORTANT SAFETY INSTRUCTIONS Read the following safety instructions carefully before using this massager. If you suffer from any of the medical conditions listed below, consult with a doctor before using this relaxation massage device. If you: suffer from a heart condition. have a sensory disorder or pacemaker suffer from osteoporosis or diabetes are pregnant have a malignant tumor are undergoing medical treatment are physically disabled suffering from acute diseases are osteoporosis, vertebral fracture patients, such as muscle/skin disease. have the gout, arthritis, joint deformation. skin disease and allergic dermatitis have neurological disorder or perceptual disorder on skin have fractured or plastic surgery materials inside your knee, joint, legs, or feet are unable to feel normal temperature we advise you to consult with your doctor before using this massager. SAFETY NOTE: Attention: Never try to turn on the power or operate this device without having water inside the container. Attention: This device is designed for private use, not intended for medical or commercial purpose. Children should be supervised to ensure that they do not use this device as a toy. CAUTION: Never try to turn on the power or operate this device without having water inside the container. Do not immerse the device into water for cleaning. DO NOT attempt to stand up on this device or its water container or walk into the foot bath container. Use it only when you are being seated on a chair or sofa. 2
Do NOT try to plug or unplug the power source if your hands are wet. Do not try to touch the control panel if your hands are wet. Do not use the device if you are hungry, right after meal, drunk, or right after extreme exercise. Do NOT use the device if you have wound or after surgery and not yet fully recovered on legs or feet. Do NOT use this device continuously for more than 50 minutes at a time. The device has preset working time of 50 minutes. It'll automatically turn off when the time is up. It is recommended to take a 10 to 15 minutes break for every 50 minutes of use. Do not use this product while you are sleeping and avoid falling asleep while the product is operating. Always remove the plug from the power outlet after use. Never leave this device unattended while power is connected. Never use the device close to heater, fireplace, stove or heat source. Always escort and pay attention while children, patients, disabled and elderly people are using this device. Never use the device if the plug or wire is damaged, not in a smooth operation as it should be, broken or wet. People with heart disease or prohibited to have excited exercise should not use this device unless you have consulted with your doctor. People with skin allergy, wounded or after surgery and not well recovered should not use this device unless you have consulted with your doctor. Unauthorized person is not allowed to reconstruct or replace the component of this device. Do not use this device in sauna room or bath room, or in area where has high humidity. Close supervision is necessary when this appliance is used by, close or next to children, invalids, or disabled person. Never let children, mental retarded and people with difficulty in action to operate this device and to reach the power source. If the device was not used for a long time, check it first before use again. Extensive use could lead to the product s excessive heating and shorter life. Should this occur, discontinue use, unplug the power source and allow the unit to cool before operating again. DO NOT use this product as a substitute for medical attention or treatment. This product is designed for home use only. MEDICAL NOTES: 1. To avoid excessive stimulation of skin, the massage time should not exceed the recommended 50 minutes at a time (its default time). 2. If your doctor / orthopedist does not particularly forbidden foot spa massage, you can enjoy the massage following your doctor's instruction. 3. A massage should never feel unpleasant. Should pain or discomfort result, discontinue use and consult your doctor. 3
4. Over exaggerated massage can also harm the body. 5. People who are unable to feel normal temperature, the ill persons undergoing medical treatment and children should not use this device. In case of injuries to legs and feet, a massage can be dangerous. If in doubt, talk to your doctor beforehand. WARNING 一 TO REDUCE RISK OF BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS: 1. This device should never be left unattended when plugged in. Unplug from outlet when not in use. 2. Close supervision is necessary when this device is used by, on, or near children, invalids, or disabled persons. THIS DEVICE IS NOT A TOY. 3. Use device only for its intended use as described in this manual. 4. Never operate this unit if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to service center for examination and repair. Never try to repair this device by yourselves. 5. Do not carry this unit by the supply power cord or use the power cord as a handle. 6. Turn all controls to OFF position, before removing plug from outlet. 7. Use only the original adaptor that comes with the device. 8. It is recommended not to use any electronic devices while using the foot spa massager, avoid possibly dropping electronic devices into water container. NOTICE: this massager should not be used in the following cases: Massage should be comfortable and pleasant. Should pain or discomfort result, discontinue use and consult your doctor. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. This product should never be used by an individual with a medical condition that would limit the user capability to operate the controls. Never use this product directly on swollen or inflamed areas of the skin or on areas where skin eruptions are present. Do not operate after taking pain killers, sedatives or alcohol. Consult your doctor if under these medications. Always unplug the power cord from the electrical outlet after using it and before cleaning it. Keep power cord away from heat or wet sources. DO NOT immerse this device in water or with any other liquid. DO NOT use attachments that are not recommended by manufacturer with this device. Do not use it when you have insensitive skin in your targeted areas or in the environment of poor air circulation. The unattended use of heat by children or incapacitated persons may be dangerous. It is recommended not to use the device 30 minutes before or after meal. 4
SPECIAL WARNING: DO NOT place or store this device where it can fall or be pulled into a tub or sink. DO NOT place in or drop into water or other liquid. DO NOT attempt to plug or unplug the power source while your feet are in the water container. Use the device on a dry sturdy level surface. Always unplug the power source when loading water or moving the unit. Consult your doctor before using this device if you have diabetes, as diabetes can contribute to foot problems including decreased feeling or circulation to the feet. If you take foot spa everyday, you should rub lotion or skin moisturizer and wear socks for keeping warm after taking foot bath. ATTENTION: This device is being tested with water at factory, if there is any water drops left inside water container, it is normal. To speed up water heating time and save electricity, it is fine to put warm water into water container, but the warm water temperature should be less than 40 Celsius degrees. Do not leave water inside the water container if the room temperature is lower than 0. Frozen water inside the device may cause damage to its components. 5
SPECIFICATIONS: Default working time: 50 minutes. Default water drainage time: 3 minutes. (Turn on the drainage function again if you need more time to drain out all water). With 110V/60Hz power cord. Power consumption: 800W. (KH298) 6
PRODUCT PARTS: Figure 1: Figure 2: 7
Figure 3: Figure 4: 8
Figure 5: water drainage OPERATION INSTRUCTION: NOTE: You must fill in water before turning on the foot bath massager. Never try to operate this device without having water inside the water container. 9
1 Put the Device together 2 Stabilize the Device Refer to Figure 2/3/4. Remove the tape on the waterfall cover (Figure 4). Put back the power cord storage cover to the massager. And close the storage compartment with power cord inside so that it will not get wet when filing in water (Figure 2). Pull up the waterfall cover to change or replace the herbal bag basket (optional) (Figure 3). Check and make sure there is no any damage on the product such as its case and power cord. Allocate the massager on the flat floor where you want to use. Make sure the 4 wheels on bottom of massager are stabilized so that the massager will not move away during use. Do Not plug in power cord to wall outlet now. 3 Filling in Water You must fill in water before turning on the foot bath massager. Never try to operate this device without having water inside the water container. Filling in water with water bucket. Do NOT put your massager under faucet directly. Be careful NOT to spill water onto the cover or control panel. To save electricity or speed up water heating, you can put in warm water but the warm water temperature should be less than 40 Celsius degrees. Water Level: (refer to Figure 4) Water level should not higher than the waterfall output level if you are using waterfall function. Water level should not higher than the water jet output level if you are using water jet function. The maximum water level is right under the waterfall output spot. If you are using both waterfall and water jet function, water level should not higher than water jet output spot. Never filling in water that is higher than its maximum water level, it'll affect the waterfall or water jet massage function. After filling in water, make sure your hands are not wet, use a dry cloth to clean up any water drops on control panel. Plug in power cord to wall outlet. 4 ON/OFF Press ON/OFF button once, ON/OFF indicator light is on 10
in red, the two-digit LED display immediately shows the current water temperature. Press the ON/OFF button again to turn off power completely. The default massage program is P1 once the power is turned on. The default massage time is 50 minutes once the power is turned on. (Figure 1, shows 50 min on the LCD display). The default minimum water heating temperature is 35 C and maximum water temperature is 40 C once the power is turned on. 5 Heating Press the Heating button to turn on/off heating function. Automatic water temperature balancing system: The default maximum water heating temperature is 40 C once the power is turned on. If the just-filled-in water temperature is lower than 40 C, the Heating function will be turned on automatically and stopped when its water temperature reaches 40 C. When its water temperature cools down below 40 C, the Heating function will be turned on automatically again, and so on. When the water temperature reaches its default maximum temperature (40 C), the Keep Warm indicator light on LCD display will be on (Figure 1). Note: the Heating function will not be on if your fill-in water temperature is already higher than its default maximum 40 C. Changing the Default Water Heating Temperature: If you prefer to change its default water temperature to be higher or lower than 40 C, you can press the TEMP + / TEMP - to reset the maximum water heating temperature. The highest heating temperature you can set is 48 C. The lowest heating temperature you can set is 35 C. 6 Temp+/- When to use Temp+/- : The Temp+/- button can be used to change maximum water heating temperature under any massage modes. Press TEMP + to increase water heating temperature you want. After 3 seconds, its LCD display will switch back showing its current water temperature. Press TEMP - to decrease water heating temperature. After 3 seconds, its LCD display will switch back showing its current water temperature. 11
Minimum and Maximum Water Temperature: The highest heating temperature you can set is 48 C/117 F. The lowest heating temperature you can set is 35 C. If you do not press the Temp+/- button to adjust the default heating temperature, the water temperature will stay in between 35 C/95 F - 40 C/104 F (default setting). The Automatic Water Temperature Balancing System will be initiated to turn on/off the Heating function automatically to keep water temperature in between 35 C/95 F - 40 C/104 F (default setting). 7 Mode There are 4 massage programs (modes), P1, P2, P3, P4. Press the Mode button to choose different programs. Default massage program is P1 once the power is turned on. You can always press Massage button to turn on/off massage function under P1. (Figure 1). P1: Under P1, water temperature, massage, air bubble, and ozone function can be chosen based on your need. All buttons on the control panel are available for selection. Under P1, if you do not change its default water temperature, its water temperature will stay in between 35 C/95 F - 40 C/104 F (default setting). 8 Two-Digit display P2, P3, P4 (Preset spa programs): Under P2, P3, P4 program, each of these 3 programs has its own preset massage pattern such as its water temperature, air bubble, ozone or massage. Under P2, P3, P4 program,you can not make any change by yourself except the Temp+/- function. (Refer to Figure 6). If you do not change its default water temperature, its water temperature will stay in between 35 C/95 F - 40 C/104 F (default setting). Except Temp+/- button, If you press any other buttons on control panel under P2, P3, P4 mode, it'll be switched back to P1 program. When the power is turned on, the LED screen displays its current water temperature inside water container and its default working time (50 minutes). 12
9 Air Bubble & OZONE Under P1: Press Ozone button once to turn on both Air Bubble and Ozone massage. Press Ozone button twice to turn Off Ozone massage. Press Ozone button third times to turn Off Air Bubble massage. Under P2, P3, P4: Air Bubble / Ozone function cannot be adjusted under preset spa programs (P2, P3, P4). (Refer to Figure 6). 10 Massage Press Massage button to turn On/Off massage function. Massage button only can be selected under P1. It cannot be selected under preset spa programs (P2, P3, P4). If you do, it'll be switched back to P1. (Refer to Figure 6). 11 Water Drainage This device has motorized water drainage system with double-lock safety switch. After each use, before trying to drain out water, always turn off all functions on control panel (but not to disconnect the power cord from wall outlet). The Drainage button on control panel cannot be used before the Drainage Switch is switched down at the back of case (Figure 2). Drainage step by step procedures: Put a water bucket under the water drainage valve. (Figure 5). Switch down the Drainage Switch at the back of case (Figure 2). The water drainage valve will open (Figure 5). At this time, the LCD screen shows water temperature 00 and its default drainage time 3 minutes. Its drainage indicator is on. Once the Drainage Switch is switched down, all buttons (except Drainage button) on control panel are not available. This is the double-lock safety system. Press the Drainage button once on control panel to turn on water draining, and water drainage starts. During water draining you can always press the Drainage button to pause drainage when you have to change or replace your water bucket. After 3 minutes, if water is not completely drained out, you can press the Drainage button to do draining again. Press Drainage button to turn off drainage. Close the water drainage valve (Figure 2). 13
Switch up the Drainage Switch (Figure 2) to completely lock up the drainage system. 12 Using bath salt / The herbal bag basket is located inside the waterfall cover. herbal bag / (Figure 3). mineral bag Pull up the waterfall cover gently to change or replace the herbal bag basket. You can put bath salt/herbal bag in this basket. 13 Waterfall and Waterfall / Water Jet switch is located inside the water Water Jet container. (Figure 3). Waterfall and Water Jet function can work alone or simultaneously. Switch the Waterfall Switch to left or right to choose waterfall or water jet function. Switch the Waterfall Switch to center position to have both waterfall and water jet function worked at the same time. 14 Clean up Make sure your hands are not wet when unplugging power cord. After each use, before trying to clean up the container with dry towel, always turn off power on control panel and unplug the power cord from wall outlet first. Put power cord back to the storage compartment and have it closed properly. Do not use the power cord as a hanger to pull or drag away the massager. Use only soft, dry cloth to clean up the control panel. Figure 6: (work pattern for P2/P3/P4) NOTE: under P2/P3/P4, all functions are preset and not selectable. If you press one of these 3 functions, it'll switch back to P1 program. Mode - P1 Heating (Temp+ / Temp-) Massage Air Bubble Ozone Time (Minute) Mode - P2 Heating, Massage, Air Bubble, and Ozone are selectable. Yes Yes Yes Yes Preset: 50 minutes Preset - all functions are NOT selectable except Heating Temp+/Temp- 14
Heating (Temp+ / Temp-) Preset: maximum heating temperature 41 Celsius. Massage Preset: when water temperature reaches 39C, massage is On for 1 minute and Off for 1 minute, stopped after a cycle of 10 minutes. Air Bubble Preset: NOT working Ozone Preset: NOT working Time (Minute) Preset: 50 minutes Mode - P3 Heating (Temp+ / Temp-) Preset - all functions are NOT selectable except Heating Temp+/Temp- Preset: maximum heating temperature 42 Celsius. Massage Preset: when water temperature reaches 39C, massage is On for 1 minute and Off for 1 minute. When Massage is On, Air Bubble is Off, and vise versa. Air Bubble Preset: when water temperature reaches 39C, Air Bubble is On for 1 minute and Off for 1 minute. When Air Bubble is On, Massage is Off, and vise versa. Ozone Preset: NOT working Time (Minute) Preset: 50 minutes Mode - P4 Heating (Temp+ / Temp-) Preset - all functions are NOT selectable except Heating Temp+/Temp- Preset: maximum heating temperature 43 Celsius. Massage Preset: when water temperature reaches 39C, Massage is On all the time until you turn it off. Air Bubble Preset: when water temperature reaches 39C, Air Bubble is On for 2 minutes and Off for 1 minute, until it is turned off. Ozone Preset: NOT working Time (Minute) Preset: 50 minutes Features: Adopt ceramic and mica insulating design, double insulation for water and electricity to maximize safety. Ozone therapy function: ozone therapy is an unique form of therapy that both heals and detoxifies at the same time. Ozone stimulates increased uptake of oxygen and improves body circulation. Strong air bubble massage with both waterfall and water jet functions, waterfall and water jet can work alone or simultaneously. Strong waterfall and water jets surfing water cycle with 300 massage burls simulating foot reflex zones. 15
With smart thermal control water temperature automatic balancing system. Calf-deep water container, water height about 18-20 cm. Infrared heated therapy function. Selective water temperature based on different needs. Equipped with detachable herbal bag container, one extra mineral stone container included. Smart design with LED indicator. Over-heat protection. Four selective automatic massage programs. Motorized rolling massage with four massage rollers. Motorized water drainage system with smart design, automatic lock or unlock system when draining. With built-in carrying handle. With hidden compartment for drainage and power cord storage. Built-in mobile wheels, easy for moving around and water drainage. Specifications: Default massage time: 50 minutes. Default water drainage time: 3 minutes. Default water temperature: 35 C/95 F (lowest) to 40 C/104 F (highest). The highest heating temperature: 48 C/117 F. The lowest heating temperature: 35 C/95 F. With 110V/60Hz UL power cord. Power consumption: 800W. (KH298) Luxury water container, big enough for any foot sizes. Cleaning and Maintenance Before cleaning, you must turn off the device and unplug the power cord from the electric outlet. Make sure the water drainage valve is closed and the power cord is properly stored inside the storage compartment. It is recommended to always drain out water along the water drainage valve; do not pour out water over the control panel. Clean the water container only with a soft cloth. Never use strong abrasives, detergents or cleaning agents for cleaning. Do NOT immerse the massager in water or under faucet to do cleaning. If you put in bath salt, herbal bag, or other spa detergents, try to clean up right after use to make sure the water valve is not blocked. To clean up, you can put in some clean water and turn on the massaging function for 1 minute and follow the water drainage procedure to drain out water. Storage 16
Unplug the appliance from the electric outlet and allow it to cool down and get dried. Store it in its box or in a clean, dry place. Do NOT drag or hang the unit with the power cord. This appliance is designed for indoor use only. Never put the appliance close to fireplace or other heating sources. Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. Troubleshooting: Problem Cause Solutions Water Jet or waterfall not working Water filter and or waterfall valve is blocked. clean up the water filter if necessary. Check and clean up the herbal bag basket. Heating not working Heating function is turned off. It may reach the preset maximum water temperature. The adjusted highest water temperature may be too low. The current water temperature inside water container is already higher than your preset water temperature. Turn on Heating function. Press the Temp+/- to adjust the preset highest water temperature. Device stops working Preset working time is up (max. is 50 minutes). Auto shut off for protection when using too long time. Try to unplug the power source completely for a while and plug in the power again. Try to unplug the power source completely for a while and plug in the power again. 17
Device stops working Massage not working under P2, P3, P4 Water drainage valve (Figure 2) is not closed. Check and make sure the water drainage valve is closed. The water temperature is too higher than your preset highest temperature. Rolling massage is over-used. P2, P3, P4 are present spa program. Try to put in some cold water to cool down the water temperature. Or, reset the highest water temperature. Turn off the device completely and let it cool down for a while before using it again Not allowed to change under preset spa programs: P2, P3, P4. Note: This product is not intended to diagnose, treat, cure, or prevent any disease. Limited Warranty Please contact seller for warranty. Limited warranty from manufacturer only for original purchaser against manufacturing or workmanship defect under normal use. Due to the hygiene or rehabilitation nature of this product, it is non-returnable. Carepeutic is a registered trademark, all rights reserved, Q.L.M. www.ideatomorrow.com Powered by Carepeutic Global Lab 18