Tullis Russell Papermakers Ltd (In Administration) By Order of Blair Nimmo and Tony Friar of KPMG LLP Joint Administrators For sale by Private Treaty Roll grinding Farrel roll grinder for grinding all paper machine rolls. Crane for loading rolls into the grinder. Building also in use as a roll store. Paper machine R1
Built 1969 with many re builds, 3800mm deckle width at reel, gsm 154 to 470, speed 80 to 260 mtrs/min. Basement machine with R/H drive. Two cantilever wire sections with part spare third wire section. Voith pressure flowboxes. Four press sections of which two are double felted, built 1998, moisture profiling steam box 2008. Dryers are rated at 70 psi operating pressure, A/F bearings, five sections, twenty - eight before the inclined size press and ten after dryers. Calender two roll stack with one Kuster roll. Drum reel up installed 2008. Paper machine QCS system ABB Smart Platform 12000 system year 2000. Paper machine DCS system ABB AC450 year 2000. Web inspection by ABB YEAR 2000. Drive sectional electric. R1 pre winder. Nash vacuum system. Stock preparation Spare broke splitter on upper level in parts. Semi automatic pulp handling and dewiring system. Sicma wire baler. Pulper for virgin pulp Sultzer Esher Wyess, 80 m³ in stainless steel, year 1990, 6% consistency. UTM pulper under dry end of paper machine Cellwood W25-84S 15 m³, stainless steel, year 1998, 2 to 6% consistency. Broke pulper Black Clawson, 14 ft diameter, stainless steel, 24 m³ capacity and year 1990. Consistency 5%. Inclined conveyor incorporating a roll splitter. Refiners: one Beloit 3000 series 34 and two Jylhavara JCO 3 refiners. Broke screens Finch horizontal year 2000. Back water fibre recovery by a Holder drum thickener. Voith stainless LD cleaners. Beloit machine pressure screens, model 10, stainless construction. Rejects to a Finch vibrating screen. In line Beloit Mag traps.
Truflo Coater Beloit coater built 1981, pre - coater installed 1996. Taking P1 and P4 base papers. Paper width 3700mm Gsm range 160 to 530 gsm Speed 210 to 400 m/min. Average operating speed 270 m/min. Cellier plant DCS Siemens 55 system 1988 Coater QCS. Lippke system 1981 Coater DCS: Alcont 1995 + Telemechanique TSX7-1995. Jagenberg Vari Roll Rewinder: model 650-15, 3800 mm width, roll diameter1500mm. Coating Kitchen Coating kitchen with various mixers, tanks and screens.
Cast coater Black Clawson manufacture, year 1988, reverse roll coater with airknife coating head applying 20 gsm of coating. Sheet width 1900mm gsm range 120 to 450, speed 20 to 65 m/ min. Coater installed 1988 with Jagenberg 5 in line Synchro sheet cutter. Sheeter adapted in 1990 as a stand alone unit. Unwind on coater is a flying splice type unwind.
Sheeter Jagenberg 3 Jagenberg model 35/215 sheeter synchro operation, year 1988, number 30-74136, two roll shaftless unwind, three slitters, Reject layboy with built in shredder. 1600mm width, sheet length 590 to 1600mm, sheet width 260 to 2000mm on the unwind, gsm range 120 to 500, roll change auto splicing, speed 60 to 300 m/min, tabbers in layboy trim widths 30 to 80mm, pallet height in layboy up to 1.5 mtrs, roll diameter max 1.5 mtrs. Sheeter Jagenberg 4 Jagenberg model 35-165 sheeter: synchro operation, year 1990, number 30-74352, two roll shaftless unwind, reject layboy with built in shredder, vacuum overlap belt, sheet length 580 to 1600mm, sheet width 510 to 1600mm, 200 to 500 gsm, auto splice unwind, reel widths 550 to 1650mm, three slitters, speed 60 to 300 m/min, join detector, pallet height 1500mm.
Sheeter Jagenberg 5 Jagenberg model 35/215, synchro operation, year 1988, number 30/74129, two roll shaftless unwind, reject layboy with shredder, sheet length 590 to 1600 mm, sheet width 260 to 2000mm, auto splice unwind, 60 to 300 m/min, tabber on layboy, three slitters, maximum pallet height in layboy:1500mm. Balers Trim balers for sheeters. Lindemann Baler (white) auto wire tying, number 211000, type BIGRO 1027. Two MOB balers (white) with auto wire tying. Hanley baler (blue) with auto wire tying. All balers with feed hoods. Core link core cutter.
Wrapper BK01 Beilomatic Folio wrapper, year 2000, number 80125217, manual ream feeding, infeed pallet heights 500 to 1500mm, sheet lengths 420 to 1200mm, sheet widths 287 to 1000mm, bundle heights 150 to 750mm, feed rate of reams 3 to 8 each minute. Norddson hot melt glue unit, wrap roll dimensions 860 to 1500mm widths, pallet out: 660+920mm minimum and 900+1200 mm maximum. Pallet height 1200 to 1480mm. In - line labeler. Pallet Wrapper MSK Pallet wrapper, plastic wrap with lowering heat tunnel which is gas heated, labeller, pallet incoming 500 to 1700mm, pallet widths 450 to 1200mm, pallet lengths 450 to 1600mm.
Laboratory with Pilot Paper Machine Laboratory Hunt and Moscrop calender Beater: Hollander type Conical lab refiner Solvo stainless batch pulper Pilot paper machine with twin wire sections, electric heated dryers, deckle width approximately 300mm deckle, press sections, two dryer sections, size press, pope type reel up. Various stainless stock chests. Lab coater and further calender. Pulp store with location of two pulpers Pulpers are for paper machines PM4 and PM5. Two Cellwood pulpers in stainless steel with auto bale feed dewiring stations. Sicma wire baler. Two stainless stock chests with side entry agitators.
Paper machine 4 Walmsley paper machine, year 1954, deckle 3340mm, twin wire sections, basement paper machine with a L/H drive, 135 to 400 gsm, speed 80 to 230 m/min. Cantilevered wet end frames, Beloit Converflo flowboxes, wire frame rebuild 2006, four press sections, two with suction rolls and one double felted. Moisture profiling steam box, dryers on A/F bearings operating at 40 psi. Twenty six dryers before size press and eight dryers after the inclined size press. Voith tandem calender with two hard roll sets, oil heated rolls, drum reel up rebuild 2009. QCS system for paper machine: Measurex ET2002 year 1988. DCS Alcont system: year 2000. Web inspection MX Open year 1998. Sectional electric drive.
Rewinder Jagenberg rewinder Vari-Dur, serial number 30-21955, builder number 5, machine basement. 1500 mm rewind and unwind, shaftless rewind with roll ejector and lowering table. Baler Hanley baler (blue) for rewinder trim. Core cutter Core link core cutter.
Stock preparation Pulper cellwood as previously described. Pulper Grubbens VC3-105/84SH, 30 m³, year 2006, 8% consistency. Broke pulper with roll splitter and conveyor feed. Sicma wire baler. Jylhavara deflaker. Two Beloit 34 3000 series refiners. Beloit model 10 pressure screens with rejects to a Finckh vibrating screen. In - line Hett separator model SP700. Bauer 606 LD cleaners. Back water fibre recovery by a Holder drum thickener.
Paper machine 5 Beloit paper machine, basement machine, built 1979, deckle 2960mm, 85 to 300 gsm, 140 to 370 m/min, drive sectional electric on R/H side. Two Beloit Converflow headboxes, three press sections, one suction press, one double felted press and one smoothing press. Dryers operating at 50 psi, A/F bearings, thirty two dryers prior to the inclined size press and ten after dryers. Three roll calender stack with one kuster roll. Pope horizontal reel up. Paper machine DCS and QCS Measturex ET2002 system, year 1987. Stock preparation DCS Vision 2002 system, year 2002.
Rewinder Jagenberg rewinder number 30-22688, shaft unwind and shaftless rewind with reel ejector and lowering table. Year 1978, slit widths 220 to 2950 mm, six slitters, gsm 50 to 500, speed 1000 m/min, maximum rewind diameter 1500mm. Stock preparation Pulper cellwood as previously described. Pulper Grubbens VC3-105/84SH, 30 m³, year 2006, 8% consistency. Broke pulper. Two Beloit 3000 series refiners 34. Jylhavara deflaker. Voith pressure screens, rejects to a Finckh vibrating screen. Hett separator SP1000. Back water fibre recovery by a Holder drum thickener. Bauer LD cleaners. Ream wrapper Wrapmatic Grande Risme folio ream wrapper, year 1982, pallet height infeed 530 to 1780mm, manual ream feed, sheet lengths 530 to 1200mm, sheet widths 420 to 1000 mm, ream heights 20mm to 85 mm, ream feed 7 to 10. Two roll unwind for wrapping paper rolls each maximum 1000 mm diameter. Pallets outgoing 400 to 1200mm. Forbo hot melt gluing, OEM labeller, twin layboys for completed pallets with auto ream changeover. Baler Vertical HSM baler (cream coloured).
Ream wrapper Pasaban folio ream wrapper, year 1982, manual ream feed, CALDUM hot melt glueing, HERMA labeller, single layboy for completed reams. Twin roll paper roll wrapping rolls 860 to 965 mm widths, pallet height infeed 1480mm, sheet lengths 1620 to 1620mm, sheet widths 1090 to 1320mm, ream heights 25 to 1320mm, finished pallet height 1560mm. Pallet shrink wrap Actipac in line pallet wrapper, plastic wrap with gas heated heat tunnel. Year 1992, incoming pallets 400 to 1475mm height, 400 to 1200mm widths, 400 to 1600mm lengths. Polythene wrap 100 to 140 microns. Pallet turner Located next to the Wohlenberg guillotine. The pallet turner is painted blue.
Guillotine Wohlenberg guillotine model 155, number 3005-0114, power back fence, light guarding, programmatic. Pallet turner Busch pallet turner with vibrator (grey). Lamb wrapper Lamb semi automatic folio ream wrapper, manual ream feed, paper wrap, conveyor to layboy for pallet loading. Cut size sheeter Beilomatik ream cutter cutting A4 and A3, cutting head spare, year 2003, roll widths 750 to 300mm, roll diameters 1524 to 550 mm, maximum roll weight 1300 kgs. Two roll shaftless unwind stands with air brakes and tension control, 15 to 500 m/min, layboy ream size 127 to 10 mm height, 500 sheet reams, 45 reams/min.
Ream wrapper Beilomatiik model CSW30, ream height 127 to 20mm A4, 80mm to 20mm A3, ream height SRA3 60mm to 20mm, ream height 46 x 32 is 55 x 20 mm, ream dimensions 460 x 320 mm and 257 x 182 mm. Output 30 reams/min on A4 and 15 reams min on A3. Soco System TE-780 lidder and palletiser. Sheet length 400 to 1400mm, gsm 70 to 500, manual wrap roll change, minimum roll width 520mm, speed 140 m/min. Pasaban sheeter Marquip Sheeter Sheeter Pasaban, synchro cut, two roll shaftless unwind stands. Auto tension control. In line Henderson embosser, year 1975, embossing width1080 to 360 mm, 70-500 gsm, roll finishes are linen, fine linen, pinhead, fine ridge, linen, hallmark linen, wave, laid, cambric, weave, ridge, hammer two side, hidden image. Spare bowls A0.0036, B 0.0020, C Wave C roll, steel roll and elastic roll. With inline reject layboy with shredder, four slitters, 400mm to 1400mm sheet length, 70 to 500 gsm, minimum roll width 520mm, speed 140 mtrs/min. Ream counter and taber. Marquip synchro sheeter, year 2007, 4 roll shaftless unwinds, auto tension control, sheet length 280 to 1650mm, sheet width 400 to 1600 mm, gsm 90 to 500, auto splice on unwind, roll size on unwinds 450 to 1700mm, roll diameter 1500mm, pallet height on accept layboy 1580mm, speed 50 to 300 mtrs/min. Reject layboy with shredder. Ream counter and taber. Strachan and Henshaw sheeter Sheeter with twin two roll 1500mm diameter, shaftless floor pick up unwind stands, tension control, four slitters, sheet length 520 to 1400mm, sheet width 402 to 1590mm, reject layboy with shredder, overlap section to layboy for pallets. Maximum height 1580mm, ream counting and taber.
Jagenberg Sheeter number 1 Jagenberg synchro sheeter, sheet length 560 to 1650mm, sheet width 402 to 1840mm, five slitters, 90 to 400 gsm, twin double floor pick up, shaftless unwind stands, ream counter and taber. Manual splicing, speed 60 to 250 m/min, pallet height 1580mm. Reject layboy with shredder. Jagenberg Sheeter number 2 Jagenberg synchro sheeter, serial number 3073256, year 1981, sheet length 560 to 1650mm, sheet width 402 to 1840mm, five slitters, 90 to 400 gsm, twin double floor pick up shaftless unwind stands, ream counter and taber. Manual splicing, speed 60 to 250 m/min, pallet height 1580mm. After unwind the sheeter has an in line wood and Stirling laminating station, reject layboy with shredder. Jagenberg Rewinder J110 Rewinder serial number 30311954, width 2794mm, shaftless foor pick up unwind, shaftless rewind, tension control. Jagenberg Rewinder J120 Rewinder serial number 3022945, width 3048 mm, type 33-15/500AB3050, shaftless floor pick up unwind, shaftless rewind. Tension control.
Roll wrapper Trancell roll wrapper with conveyor roll feed from the two Jagenberg rewinders. Plastic roll wrapping. Balers Balers Two vertical load balers, one light blue and other dark blue. Two external Hanley balers for Jagenberg 1 and 2 sheeters also for Jagenberg 110/120 rewinders. Final sheeting baling area Powell Jag 1 baler: vertical hydraulic baler with feed hopper, wire tying colour white with blue baler. Lindeman Jag 2 baler: blue horizontal hydraulic. Hindle baler: blue horizontal hydraulic. Lindemann: horizontal hydraulic baler: BALE 2343 MARDON vertical loading baler Hanley vertical hydraulic baler located near to pallet conveyor. MRP1 roll storage area.
Laboratory equipment All equipment has been stored in one location in the mill. A complete phototograpic data base is available via a link on this document. N.B. In association with GMG Asset Management UK Ltd. Please see www.gmgasset-management.com for details of the online auction of additional ancillary equipment. THIS INFORMATION IS THE TITLE OF JOHN WILKIE PAPER MILL SERVICES LTD AND SHOULD NOT BE COPIED OR FORWARDED TO A THIRD PARTY WITHOUT CONSENT. FOR YOUR GENERAL INFORMATION WE HAVE TO INTIMATE THE FOLLOWING TO YOU: This schedule has been prepared solely for the guidance of prospective purchasers and does not constitute (and at no time shall be deemed to constitute) an offer or contract or any part of an offer or contract. Additionally, no warranty is given to the accuracy of any measurements, specifications or other details whatsoever given within this schedule. Whilst every reasonable effort has been made to verify any statement, description, or comment made within this schedule, for the avoidance of doubt it is emphasised that the purchaser must make their own enquiries and satisfy themselves.