Automatic Drum Washing Machine Service Manual Suited model: HWD1000 Features Sense the temperature in drum while drying, stop when clothes dry Adjustable washing time LED display Memory the habit washing process in CUSTOM program Serial umber: SMHWD1000-1 Version:00.00 Edition: 2006-5-10
1 Contents----------------------------------------------------------------------------------------1 2 Product code illumination and series introduction-----------------------------------2 3 Features ---------------------------------------------------------------------------------------3 4 Specification ----------------------------------------------------------------------------------4 5 Safety ------------------------------------------------------------------------------------------6 6 Installation ------------------------------------------------------------------------------------10 7 et dimension -------------------------------------------------------------------------------13 8 ames of the parts-------------------------------------------------------------------------14 9 Operational functions----------------------------------------------------------------------15 10 Program description table --------------------------------------------------------------17 11 Error display and troubleshooting-----------------------------------------------------19 12 Wiring circuit -------------------------------------------------------------------------------28 13 Exploded view and list of parts--------------------------------------------------------29 Page 1
PRODUCT CODE ILLUMIATIO AD SERIES ITRODUCTIO Model code rule description Model identification HWD A 1000 B A B Serial code Max spin speed Page 2
FEATURES Selling Point Dry clothes intelligently and stop automatically when clothes are dry. Benefits Intelligent drying Automatic washing program Washing load selecting automatically Technical Supports Automatic moisture sensing for the clothes and stop of operation when the laundry is dried, saving energy and trouble. Unique function of self-programming of washing procedure, washing at your pleasure. Four display screens, the washing process being clear at a glance. Six-level smart protection, 59-minutes standard procedures capable of remembering washing habits for time saving and convenient operation. Page 3
SPECIFICATIO Proposal Automatic Drum Washer and Dryer 2006 ew Sensor HWD1000 1. Product identification Description of appliance Washer and Dryer Type of appliance (FS = standing, BI = built-in) FS Supplier own brand Supplier bar code UPC 688057394381 Mares computer code / Commercial Brand / Model / Commercial bar code UPC / 2. Key-Features Energy efficiency class Washing performance class Spin efficiency class Programs Capacity(washing) kg / / / 6 5 Spin speed (max. / optional) rpm 1000-400 oise level db(a) 72 Energy consumption per wash circle * kwh / Water consumption* l 53 Residual dampness (spin result) % 78.7% Spin speed selector switch (steps) rpm 1000/800/600 Spin speed variator (stepless) rpm - Adjustable thermostat ( water temp. adjust from - to) C - Drum capacity l 47.8 Auto water level adjust (depending on volume of filled in laundry) AWL Washing time (max.) min 139 Washing temperatures (program-controlled) H/W/C Certification's ( ETL) ETL/CETL Approvals ETL * E 60456 (60 C cycle, full load without pre-wash) = COLD / 3. Basics data Unit dimensions (H x W x D) cm 86x48.5x59.5 85X59.5X55 et weight kg 81 Voltage/frequency V/Hz 120V~60Hz Input power / main fuse (intensity) W/A 1300/12 Work top / removable Control M = electromechanical, E =electronic, F = fuzzy E Drum S = stainless steel / Z = zinc coated S Tub P = Polyprop./ S = stainless steel S Door: aesthetic ( R=round, =big eye, Q=square) R Diameter cm 30 Outer door frame S= stainless steel / M = metal / P = plastic P Inner door G =glass / P=plastic G Detergent compartments n 3 Removable compartment for liquid detergent - Page 4
Delay timer (from - to) Self cleaning suds pump Water inlet hose Water drain hose Adjustable feet n 4 4. Safety systems Auto door lock ADL Motor overheating protection MOP o heating without water Auto water cool-down (before drain 80 C boiled water) Water return protection Acqua Stop kit Child protection 5. Programs 1) Standard 2) Custom 3) Quick 4) ight 5) Heavy Pre-wash Delicate / hand wash Wool / cashmere Soak Drain Easy ironing Optional function keys (additional program settings) O/OFF button Half load Rinse Spin exclusion Spin speed selection Program o Soak Dry Delicate Cold wash START/PAUSE Extra Rinse Water level Door lock indicator Temperature selection (H/W/C) 5kg wash Prewash HW AWC WRP rpm - / - - - - / - - - - - - Remark : " " signify the washing machine has this function "- " signify the washing machine does not have this function Page 5
The appliance must be positioned so that the plug is accessible. Used new hose-sets and that old-sets should not be reused. Page 6
Page 7
Page 8
Page 9
Page10
Page11
Page12
et Dimension 595 550 850 height: 850mm / width: 595mm / depth: 550mm Page 13
ame of the parts Page 14
Page 15
W C H W H W C Page 16
Page 17
Page 18
HWD1000 Error Display and Troubleshooting Error message:the required water level is not reached within 8 min Check if water is leaking from washer bottom. inlet pipe. drain pipe or other pipe connection Readjust or replace the broken parts Check if tap is closed or water pressure is too low (usual between 0.05-1MPa) Open the tap or wait for normal water pressure to use Check if inlet valve is jammed Clean inlet valve Draw out the dispenser and check if water is entering Observe if the height of drain pipe not reach 80 cm. If water level sensor and the hose is leaking gas Turn on power, and set pre-wash mode, then start. Check the import voltage of electromagnetic valve by multimeter,isitbetweenac120v? Electromagnetic valve must be broken, please replace it. Check if export voltage from board to electromagnetic valve, is between AC 120V? it The wire connected display baord and inlet valve is not properly. Please reconnect it or replace it. Replace display board Page 19
Error message:drainage error, water not emptied within 5 min. Check if water is emptied Check if water level pressure switch is undamaged. Check if drain pump acts by touching pump position Check if drain pump or drain pipe is jammed, and open the filter and clean Cut off the power and choose spin program to start, then check the import voltage of drain pump, is it between AC 120V? Replace drain pump Cut off power and pull out water level pressure switch wire connection. Set spin program to start. Check the export voltage to drain pump, is it between AC 120 V? The wire between display board and drain pump is not connected properly. Replace the wire. Replace display board Error message. Water level exceeds protective value. Check if water switch hose and air collector are jammed Clean water switch hose and air collector Without power,connect inlet pipe to inlet vavle,then open the tap and observe if water is entering in dispenser Replace inlet valve Replace water switch Without starting but electrifying, measure the import voltage of inlet valve, is it between 120V Replace display board AC120 V? Page 20
Error message. Motor overheat protection or is damaged. Cut off power and check if motor wires are connected well Reconnect well Pull out the wire connection of motor Then check if circuit is open by multimeter Repair wires Replace display board Error message: Water level is abnormal in the drying process check if the wire connected display board and inlet valve is not properly. Please reconnected it Check if drain pump acts by touching pump position Check if drain pump or drain pipe is jammed, and open the filter and clean Cut off thepower and choosespin programto start, then check the import voltage of drain pump, is it between AC 120V? Replacedrain pump Cut off power and pull out water level pressure switch wire connection. Set spin program to start. Check the export voltage to drain pump, is it between AC 120V? The wire between display board and drain pump is not connected properly. Replace the wire. check if the stream adjuster is broken. Please replace it Replace display board Page 21
Error message:the water level sensor circuit short cut or open Check if the wire of water levle sensor is connected properly Connect it well Check if the water levle sensor is damaged Replace it Replace display board Error message:the temperature of air vent Check if the wire of heater is connected properly Connect it well Check if the fuse is connected properly Connect it well Turn on power and choose dry program to start, measure if voltage of heater by multimeter,is it between AC 120v? Heater element must be broken, please replace it The control wire may be broken, otherwise display board must be broken. Please replace the broken one. Page 22
Error message: The dry temperature sensor short cut or open. Check if the dry temperature sensor is connected properly Connect it well Check if the dry temperature sensor is short cut or open Replace it Replace display board Error message:door is not properly shut 20s after program is started. Pushing the door to Check Whether Door is properly shut or not Shut the door properly. Cut off the power and then turn on again. Check the voltage of door lock, is it between AC 120 V? 120v Door lock is broken and need replacing, then make sure wire is connected properly. Check if the wire connecting door lock and display board is loose Connect the wire properly Replace display board Page 23
Error message:spin losidedly ou can disperse the clothings evently in the tub and restart the SPI program. Error message: Unclose the door before start program Close the door properly Error message: The memory function is failure The EEPROM may be go wrong, plese replace display board Page 24
HWD1000 Failure:Display nothing Measure the power supply,is it exists 120V AC voltage Automatic Drum Washing Machine Examination & Troubleshooting Repair power supply Is power switch on? Press the power switch Press power switch and check the voltage between two pins of power switch. Is there 120V AC voltage? Make sure power supply cable assembly is connected well and then replace power switch. Cut off power and check if plugs are connected well by pulling the plug of display board. Insert the plug well and test Check if power plug exists 120V AC Replace display board voltage at the import pin Failure:no water inletting Is the tap shut off or the water pressure too low? Open tap or wait for normal water pressure Check if water is leaking from washer connection, especially between inlet pipe andtap.tomakesureofnobends. Reconnect inlet pipe. Check if filter of electromagnetic valve is Clean filter jammed Choose pre-wash program and start Check if there is 120V at import pin of electromagnetic valve 120V Replace electromagnetic valve Is there open circuit betw een electromagnetic valve Reconnect the wire Choose pre-wash program and start then check if there is 120 V at export 120V Replace display board pin of electromagnetic valve Page25
Failure:no draining Is the height of drain pipe too high? Automatic Drum Washing Machine Adjust the height of drain pipe to 80-100 cm Turn filter anticlockwise open and check if filter is jammed Clean and tighten filter clockwise. Check if hose connecting cylinder to pump is bent or jammed Arrange hose and clean Turn on power and choose spin program to start. Measure if import voltage of drain pump is 120 V Replace drain pump Cut off and check if the connection between drain pump and display board is open Replace the wire. Turn on and choose spin program to start. Measure if export voltage of display board to drain pump is 120V Replace dispay board Failure :abnormal noise and vibration Is the pack screws dismantled? Dismantle the screws Is there foreign material in the washer? Clean Is washer in balance? Adjust adjustable feet Is belt loose or worn? Replace it Are the screws of counterweight and motor loose? Fasten them Remove belt and turn belt pulley by hand, and then check if there is different Dismantle triangle and check the bearing.if it is broken, replace it. Turn on power and set spin program, then start check if there is different noise from motor Replace motor Page26
Failure:water leaking Check if water is leaking from the inlet pipe or the tap Readjust it. Is drain pipe broken Replace drain pipe Check if there is foreign material nipped between cushion of sight window and sight window Remove clothes Check if all tubes and tie-in is leaking water, including the connecting of tube and valve, dispenser, tube and dispenser,outer cylinder-cushion of sight window-hose and outer cylinder, drain pump and gas valve Reassemble or repair Is cushion of sight window broken? Replace cushion of sight window Is water leaking from outer cylinder? Replace outer cylinder Page 27
Electronic system diagram thermal link 128C C ' IP thermostat '' CL '' ' Page 28
Sincere Forever Group