DCPFRCME FAT REPONE CONTACT MODULE TANDARD FEATURE ingle input contact monitor Fast, reliable contact monitoring utilizing the Hochiki DCP (Digital Communications Protocol) Two different mounting configurations 127 devices can be used per DCP loop Bicolored indicating LED provides module status (FRCME4 only) Can be programmed to monitor Normally Open (NO) or Normally Closed (NC) contacts Operates on Class A or Class B LC loop Accepts up to 14 AWG wire UL listed UL 864 FRCME4/ FRCME only C943 MEA 28491E Vol. IV FRCME4 PRODUCT LITING 3022559 California tate Fire Marshal 73000410:150 PECIFICATION Operating Voltage DCP Powered Loop 17~41 VDC Average Current Consumption 550 µa (Typical) Alarm Current 8mA Dimensions FRCME4 4.2"W x 4.7"H x 1.4"D FRCMEP 3.0"W x 1.9"H x 0.5"D FRCME 2.8"W x 1.8"H x 0.7"D Ambient Temperature 32 F (0 C) ~ 120 F (49 C) Max. Humidity 90% RH, noncondensing Mounting FRCME4 Mounts to double gang/4" square back box FRCME/FRCMEP Mounts inside a single gang back box DERIPTION The Hochiki FRCME Fast Response Contact Monitoring Modules are designed to be used with pull stations, water flow switches, and other applications requiring the monitoring of dry contact alarm initiating devices. The interrupt driven Digital Communications Protocol (DCP) combines maximum communication reliability and fast response to emergency conditions. Two different mounting configurations are provided to meet a wide range of applications. The FRCME contact monitoring module does not require a separate 24 VDC power source. Each addressable contact monitoring module is programmed with its own unique ignaling Line Circuit (LC) loop address. The device address is electrically programmable and stored in onboard EEPROM. Up to 127 devices can be placed on the Hochiki DCP LC loop. The module supervises the wiring to the contact with an End Of Line (EOL) resistor. It can be programmed to monitor Normally Open (NO) or Normally Closed (NC) contacts. If a fault condition occurs in the wiring, the module sends a trouble status signal to the fire alarm control panel. When a change of status (contact changes state) is sensed by the FRCME, it sends an interrupt to the FireNET control panel indicating that an alarm has occurred. The FRCMEP and FRCME are small package designs and are suitable for mounting in a small junction box behind a pull station or other monitored device. The FRCME4 is mounted to a cover plate for a 4" square or double gang junction box. It contains a visible bicolored indicating LED to provide module status. Continued on back. Find latest revision at www.hochiki.com 7051 Village Drive, uite 100 Buena Park, CA 906212268 Phone: 714/5222246 Fax: 714/5222268 Technical upport: 800/8456692 or technicalsupport@hochiki.com F0002 02/2008
ENGINEERING PECIFICATION The contractor shall furnish and install where indicated on the plans, addressable contact monitoring modules Hochiki DCPFRCME4, DCPFRCME and FRCMEP. The modules shall be UL listed and compatible with the Hochiki FireNET fire alarm control panel. The device address shall be electrically programmable and stored in EEPROM. The FRCME and FRCMEP shall fit inside a single gang electrical back box. The FRCME4 shall be supplied with a plastic face plate and shall be suitable for mounting to a 4" square or double gang electrical back box. The FRCME4 shall provide a monitor LED that is visible through the face plate. FRCME4 FRCME FRCMEP OUT TO NEXT MODULE TYPICAL WIRING FOR N/O CONTACT ONLY WIRING DIAGRAM FRCME4/FRCME IUE NO. AH9755 DCPFRCME4 + INA INB ALL WIRING HOWN I UPERVIED CONTROL ANY NUMBER OF UL LITED N/O CONTACT CLOURE DEVICE MAY BE UED. DO NOT MIX FIRE ALARM INITIATING OR UPERVIORY ON THE AME MODULE OUT TO NEXT MODULE IUE NO. AH9755 DCPFRCME4 + INA INB CONTROL TYPICAL WIRING FOR N/C CONTACT ONLY FRCMEP OUT TO NEXT MODULE ALL WIRING HOWN I UPERVIED TYPICAL WIRING FOR N/O CONTACT ONLY CAUTION! DO NOT CONNECT MORE THAN ONE N/C CONTACT TO AN INPUT. IUE NO. AH9765 DCPFRCMEP (OUT) RED (IN) (OUT) BLK (IN) WHT INA INB CONTROL ALL WIRING HOWN I UPERVIED OUT TO NEXT MODULE ANY NUMBER OF UL LITED N/O CONTACT CLOURE DEVICE MAY BE UED. DO NOT MIX FIRE ALARM INITIATING OR UPERVIORY ON THE AME MODULE IUE NO. AH9765 DCPFRCMEP (OUT) RED (IN) (OUT) BLK (IN) WHT INA INB CONTROL ALL WIRING HOWN I UPERVIED TYPICAL WIRING FOR N/C CONTACT ONLY DCPFRCME CAUTION! DO NOT CONNECT MORE THAN ONE N/C CONTACT TO AN INPUT.
DIMM DUAL INPUT MONITOR MODULE PECIFICATION Operating Voltage 17~41 VDC Average Current Consumption 600µA(Typical) Alarm Current 30mA Dimensons 4.2"W x 4.7"H x 1.4"D Ambient Temperature 32 F (0 C) ~ 120 F (49 C) Max. Humidity 90% RH, noncondensing Mounting 4" square electrical box TANDARD FEATURE Fast, reliable contact monitoring utilizing the Hochiki DCP (Digital Communications Protocol) 127 devices can be used per DCP loop Bicolored indicating LED provides module status Dual input contact monitor Can be programmed to monitor Normally Open (NO) or Normally Closed (NC) contacts Operates on Class A or Class B LC loop Accepts up to 14 AWG wire Mounts to 4" square gang box DERIPTION The Hochiki Dual Monitor Module (DIMM) is designed for use on the FireNET analog addressable system. It provides two independent contact monitoring circuits while only utilizing one address on the LC loop. Up to 127 devices can be placed on a single LC loop. The device address is uniquely stored on an onboard EEPROM. The module can be programmed to monitor Normally Open (NO) or Normally Closed (NC) contact fire alarm and supervisory devices. The interrupt driven Digital Communication Protocol (DCP) combines maximum communication reliability and fast response to emergency conditions. The module has a single bicolored LED to indicate device status. It fits into a standard 4" square or double gang electrical back box. PRODUCT LITING California tate Fire Marshal 73000410:150 3033215 Continued on back. Find latest revision at www.hochiki.com 7051 Village Drive, uite 100 Buena Park, CA 906212268 Phone: 714/5222246 Fax: 714/5222268 Technical upport: 800/8456692 or technicalsupport@hochiki.com F0003 12/2008
ENGINEERING PECIFICATION The contractor shall furnish and install where indicated on the plans, addressable contact monitoring modules Hochiki DIMM. The modules shall be UL listed and compatible with the Hochiki FireNET fire alarm control panel. The device address shall be electrically programmable and stored in EEPROM. A bicolored LED shall indicate device status. WIRING DIAGRAM Back ide of a DIMM 22K 040001000 TYPICAL WIRING FOR N/O CONTACT ONLY TB2 OUT TO NEXT MODULE + 22K 040001000 ANY NUMBER OF UL LITED N/O CONTACT CLOURE DEVICE MAY BE UED. + FIRE CONTROL 22K 040001000 TYPICAL WIRING FOR N/C CONTACT ONLY 22K 040001000 CAUTION! DO NOT CONNECT MORE THAN ONE N/C CONTACT TO AN INPUT! Dual Input Monitor Module ALL WIRING HOWN I UPERVIED DIMM
DCPCZM CONVENTIONAL ZONE MODULE TANDARD FEATURE Provides an address point for a zone of up to 25 conventional smoke detectors Blinks green when polled. Latched on red (controlled by panel) when activated Device address can be programmed with a handheld programmer. Device address ranges from 1 to 127 Compatible with Class B and Class A wiring Auxiliary power source provides power for the zone of detectors Compatible with conventional detectors, LR, IJ, LK, LV, DCD, DFE and IH series PRODUCT LITING California tate Fire Marshal 3033215 73000410:150 PECIFICATION upply Voltage () 25.3 ~ 39 VDC Auxiliary upply Voltage 18.8 ~ 27.2 VDC Average Current Consumption (On Line) 670µA 2Wire Detector Loop Current tandby Detector Load 1mA Max. From Auxiliary upply 60mA Max. EOL Device 4.7K ohms Resistor Max. Quantity Per Loop 127 Alarm Threshold Level <1.5K ohms Wiring Threshold Level >2.5K ohms & <6K ohms Open Circuit Threshold Level >10K ohms Max. 2Wire Conventional Detector (Loop Resistance) 50 ohms (total wire length) Dimensions 4.2 W x 4.7 H x 1.4 D Operating Temperature 32 F (0 C) ~ 120 F (49 C) Mounting 4 square electrical box Relative Humidity 90% RH NonCondensing DERIPTION The Hochiki Conventional Zone Module (DCPCZM) is designed for use on an analog addressable Fire Alarm system. Up to 127 devices can be placed on a single LC loop. The device address is uniquely stored on an onboard EEPROM. The module allows the panel to interface and monitor twowire conventional detectors or pull stations. Each DCPCZM transmits the status on one zone of devices (25 maximum per zone) back to the panel. It supervises the power supply as well as the entire zone of devices. tatus conditions are reported as normal, open or alarm. All 2wire smoke detectors must be UL listed as compatible to be interfaced with the DCPCZM. The interrupt driven Digital Communication Protocol (DCP) combines maximum communication reliability and fast response to emergency conditions. The module has a single bicolored LED to indicate device status. It fits into a standard 4" square or double gang electrical back box. Continued on back. Find latest revision at www.hochiki.com 7051 Village Drive, uite 100 Buena Park, CA 906212268 Phone: 714/5222246 Fax: 714/5222268 Technical upport: 800/8456692 or technicalsupport@hochiki.com 05/2010 F0004
ENGINEERING PECIFICATION The contractor shall furnish and install where indicated on the plans, Conventional Zone Module (DCPCZM). The modules shall be UL listed and compatible with the Hochiki America Analog Control Panel Protocol. The device address shall be electrically programmable and stored in EEPROM. A bicolored LED shall indicate device status. The DCPCZM shall be supplied with a plastic cover and shall be suitable for mounting to a 4" square or double gang electrical back box. The DCPCZM shall provide a monitor LED that is visible from outside the cover plate. Detector Model IH24F LIT OF DEVICE Detector Identifier HD3 Detector Type Ionization Base Model HB224 Base Indetifier LK24F HD3 Photoelectric HB224 HB53 25 HB53 Max Detectors LR24H HD3 Photoelectric w/heat N4224, N6224 HB5 25 LR24V HD3 Photoelectric N4224, N6224 HB5 25 LR835/835W HD3 Photoelectric (835V) N4224, N6224 HB5 18 N4224W, N6224W LR835H/835HW HD5 Photoelectric (835V) N4224, N6224 HB5 18 w/thermal N4224W, N6224W LR835B2/2W HD6 Photoelectric (835V) (baseless) N/A N/A 18 25 LR835BH2/2W IJ24 HD6 HD3 Photoelectric (835V) w/thermal (baseless) Ionization N/A N4224, N6224 N/A HB5 18 25 Back side of a CZM DCD135/190 HD3 Heat Fixed Temp/Rate of Rise N4224, N6224 HB5 25 DFE135/190 N/A Heat Fixed Temp H224L HB62 25 LV24/24N/24V HD3 Photoelectric N4224, N6224 N4224W, N6224W HB5 25 NFPA CLA A WIRING DIAGRAM EXPLODED VIEW 34: CLA A OPTIONAL BRANCH CIRCUIT TO NEXT INTERFACE MODULE. MODULE UPERVIE UPPLY VOLTAGE AND DETECTOR LOOP. FIRE CONTROL UL LITED 1481 24VDC + REGULATED POWER UPPLY, LITED FOR FIRE 24 24V+ PROTECTION WITH BATTERY NEXT DEVICE BACKUP. DCPCZM Conventional Zone Module IN+ 24V IN OUT+ 24V+ OUT For Dry Indoor Use Only For Proper Installation, see HA06101 Rev 03/10 CONVENTIONAL ZONE MODULE JP2 CLA A TB2 EB NOTE: ENURE JUMPER I IN CORRECT POITION FOR WIRING CONFIGURATION. (POITION 34) MAX. 25 CONVENTIONAL DETECTOR ALL WIRING I UPERVIED AND POWER LIMITED. DO NOT MIX FIRE ALARM INITIATING AND UPERVIORY INITIATING DEVICE ON THE AME MODULE. Note: LC circuit is in reference to, and NFPA CLA B WIRING DIAGRAM EXPLODED VIEW 12: CLA B FIRE CONTROL OPTIONAL BRANCH CIRCUIT TO NEXT INTERFACE MODULE. MODULE UPERVIE UPPLY VOLTAGE AND DETECTOR LOOP. UL LITED 1481 24VDC REGULATED POWER UPPLY, + LITED FOR FIRE PROTECTION WITH BATTERY BACKUP. 24 24V+ NEXT DEVICE 24V OUT+ 24V+ OUT For Dry Indoor Use Only DCPCZM Conventional Zone Module IN+ IN For Proper Installation, see HA06101 Rev 03/10 CONVENTIONAL ZONE MODULE JP2 CLA B TB2 EB NOTE: ENURE JUMPER I IN CORRECT POITION FOR WIRING CONFIGURATION. (POITION 12) MAX. 25 CONVENTIONAL DETECTOR 4.7K 040001820 HOCHIKI AMERICA CORP. 4.7K 040001820 ALL WIRING I UPERVIED AND POWER LIMITED. DO NOT MIX FIRE ALARM INITIATING AND UPERVIORY INITIATING DEVICE ON THE AME MODULE. CZM
I HORT CIRCUIT IOLATOR OPERATION * Class A Configuration Wiring: The DCPI short circuit isolator should be located between any devices on the LC loop. In the event of a short on the LC loop, the two adjacent isolators (closest isolators to the left and right of the shorted section) will activate and their respective LED indicators will be turned on. All devices between the active short circuit isolators will lose communication. This will prevent entire loop failure. Upon removal of the short condition, the DCPIs will automatically restore the entire loop to the normal operating state. TANDARD FEATURE Can be placed at any location on LC loop Checks the line for short circuit at power up. If the line is normal, the relay will be returned on. If a line short is detected, the relay remains open Indication of a single short circuit by a yellow LED PECIFICATION Absolute Max. Applied Voltage, : 41 VDC upply Voltage Norminal, : 33 VDC Normal Current Consumption 270 μa (Typical) Active Current Consumption 10 ma (Typical) (hort Circuit Condition) Dimensions 4.2"W x 4.7"H x 1.4"D Weight 1.4 oz Visual Indicator (Yellow tatus LED) No indication in normal condition. On steady in active (short) condition. Operation Temperature Range 0ºC (32ºF)~ 49ºC (120ºF) Noncondensing Allowable Ambient Humidity 90% Noncondensing * Class B Configuration Wiring: The DCPI short circuit isolator should be located between any devices on the LC loop. In the event of a short on LC loop, an isolator closest to the shorted section will activate and the LED will be turned on. All the devices beyond the shorted section will lose communication. Upon removal of the short condition, the DCPI will automatically restore the entire loop to the normal operating state. For the best performance of DCPI short circuit isolator, use class A configuration. WIRING: Note: All wiring must conform to local codes, ordinances and regulations. 1. Install module wiring in accordance with job drawings and appropriate wiring diagram. 2. ecure the module to an approved electrical box (supplied by installer). MOUNTING REQUIREMENT: 4" Q Electrical box or double gang. PRODUCT LITING California tate Fire Marshal C943 73000410:150 MEA 28491E Vol. IV Continued on back. Find latest revision at www.hochiki.com 7051 Village Drive, uite 100 Buena Park, CA 906212268 Phone: 714/5222246 Fax: 714/5222268 Technical upport: 800/8456692 or technicalsupport@hochiki.com F0008 06/2010
ENGINEERING PECIFICATION The contractor shall furnish and install where indicated on the plans, the Hochiki DCPI short circuit isolator. The modules shall be UL listed compatible with Hochiki Digital Communications Protocol (DCP) supporting control panel loops. The isolator module must be suitable for mounting in a standard 4" square electrical box or double gang. The isolator module must provide a yellow LED for indication of status. WIRING DIAGRAM Back side of a DCPI IUE NO. AH9774 DCPI (IN) (IN) (OUT) (OUT) UL LITED CONTROL LITED IUE NO. AH9774 DCPI (IN) (IN) (OUT) (OUT) HORT CIRCUIT IOLATOR GROUP OF VARIOU DCP MODULE GROUP OF VARIOU DCP ENOR HORT CIRCUIT IOLATOR OPTIONAL RETURN LINE (NOT REQUIRED) (IN) (IN) (OUT) (OUT) + + + LITED IUE NO. AH9774 DCPI TYPICAL WIRING DIAGRAM EXAMPLE, CONNECTED TO A LITED CONTROL HORT CIRCUIT IOLATOR ALL WIRING HOWN I UPERVIED ANY COMBINATION OF MODULE AND/OR ENOR MAY BE PLACED BETWEEN IOLATOR DCPI
DCPR2M DUAL RELAY MODULE PECIFICATION upply Voltage () 25.3 ~ 39 VDC Average Current Consumption Contacts Contact Rating 390µA (Typical) 400µA (Alarm) 2 Independently Controlled Form C 1Amp @ 30VDC or 0.5Amp @ 120 VAC Max. Quantity Per Loop 127 Dimensions 4.2 W x 4.7 H x 1.4 D Operating Temperature 32 F (0 C) ~ 120 F (49 C) Mounting 4 square electrical box Relative Humidity 90% RH NonCondensing DERIPTION TANDARD FEATURE UL 864 9th Edition Listed Provides two independently configurable Form C contacts per address Contacts are rated 1.0 Amp @ 30 VDC or 0.5 Amp @ 125 VAC Up to127 devices can be used on each LC loop Visible Bicolored LED is software controlled and can be programmed to blink red or green when polled. The LED can be latched on when activated. Programming is highly flexible providing 16 priority states plus zoning capability MEA 28491E Vol. IV PRODUCT LITING C943 3022559 California tate Fire Marshal 73000410:150 The Dual Relay Module (R2M), has been designed to provide flexibile and quick response to emergency conditions. The R2M allows independent control of two form C contacts for a variety of normally open and normally closed contact applications such as fan operation, elevator recall, door closure, and auxiliary notification. Each R2M module provides independent control of two Form C contacts while utilizing one LC (ignaling Line Circuit) address. The R2M module has a highly configurable programming algorithm that allows the user to setup groups of devices (zoning) for simultaneous operation of multiple R2M modules. Each module has 16 priority states that are programmed. The operating parameters are maintained by the module and do not require individual communication with the control panel during the emergency condition to operate. The control panel broadcasts the control command on the LC loop and the R2M modules do the rest based on their custom configuration. ince mechanically latching relays are used within the R2M module, a separate 24VDC power source is not required. Continued on back. Find latest revision at www.hochiki.com 7051 Village Drive, uite 100 Buena Park, CA 906212268 Phone: 714/5222246 Fax: 714/5222268 Technical upport: 800/8456692 or technicalsupport@hochiki.com 07/2010 F0058
ENGINEERING PECIFICATION The contractor shall furnish and install where indicated on the plans, the Hochiki DCPR2M addressable relay module. The modules shall be UL listed compatible with Hochiki Digital Communications Protocol (DCP) supporting control panel loops. The relay module must provide two Form C dry contacts rated at 1Amp @ 30 VDC or 0.5Amp @ 125 VAC. The relay module must be suitable for mounting in a standard 4" square electrical box or double gang. The relay module must provide a bicolored LED for indication of status. Back side of a R2M WIRING DIAGRAM WIRING TO BOTH ET OF FORM "C" CONTACT MUT BE EITHER POWER LIMITED OR NONPOWER LIMITED. DO NOT MIX POWER LIMITED WIRING WITH NONPOWER LIMITED WIRING ON TB2. CRO OUT TYPE OF WIRING NOT UED WITH A PERMANENT MARK ALL WIRING HOWN ON TB2 I NOT UPERVIED. CONTACT ARE HOWN IN TANDBY MODE REFER TO CONTROL ' OPERATION MANUAL FOR PROPER RELAY OPERATION AND CONFIGURATION. OUT TO NEXT MODULE 2 DCPR2M, WIRING POWER LIMITED ERIAL NO. XXXXXXXXX NO1 COM1 POWER LIMITED ET 1 FIRE CONTROL ALL WIRING HOWN ON I UPERVIED AND INHERENTLY POWER LIMITED HOCHIKI 1 NON NC1 POWER LIMITED + NO2 For Dry Indoor Use Only CRO OUT TYPE NOT UED COM2 DUAL RELAY MODULE NC2 B (FORM "C" CONTACT) (NONUPERVIED) ET 2 NOTE: RELAY CONTACT MAY HAVE TRANFERRED DURING HIPPING. TO ENURE CONTACT ARE IN CORRECT "NORMAL" TATE A INDICATED IN REFERENCED WIRING DIAGRAM, A "REET" COMMAND HOULD BE INITIATED FROM THE CONTROL PRIOR TO CONNECTION OF CIRCUIT CONTROLLED BY THE MODULE. DCPR2M