Malem Universal Wireless Alarm Model MO15 IMPORTANT Please read instruction booklet before use Instructions for use The alarm can be used for several applications or combinations: l Wander alarm l Continence alarm l Sit up alarm l Enuresis alarm l Sleepwalking alarm l Dialysis leakage alarm Up to seven clients can be monitored with one receiver Ideal for nursing/care homes, special schools, hospitals, institutions and individuals Helps to prevent bed sores and broken bones in Dementia, Alzheimer s, Memory Loss, the Elderly, People with Special Needs
Disclaimer Malem Universal Wireless Alarm is designed as a helpful and versatile aid. It is not intended to replace human care or supervision and the manufacturer, Malem Medical, is not responsible for any consequences resulting from the use, misuse or failure of this device.
Contents Instructions for Use Easy-Clip Sensor...2 Standard Sensor...3 Bed-Mat...4 Wander-Mat...6 Dialysis-Mat...7 Resetting Receiver (Rx) Sound...7 Channel Selection...8 Receiver LED Number Selection...8 Re-tuning (Pairing)...8 Sound Selection Switch...8 Batteries...9 Guarantee...9 Repairs...9 Cleaning...10 Disposal...10 Fault Finding...10 Specification Tx & Rx...11-12 Diagrams Tx & Rx...13-16 How to Connect Tx with Different Sensors...17-19 The Inverter...20-21 MM100111
WIRELESS ALARM TRANSMITTER MO15(Tx) Instructions for use 1. Switch on the receiver (Rx) unit. Green LED will flash once every two seconds. See page 15. 2. Remove insulator from battery compartment (if present) of the transmitter (Tx) unit. See page 14. 3. Plug the sensor of choice into the transmitter (Tx) unit. See pages 17 & 18. 4. If used with Easy-Clip Sensor (EC): i) Make sure the Easy-Clip Sensor lever is in the up position. (Lowering the lever without placing material between the front jaws will activate the transmitter and trigger the receiver buzzer). If buzzer does not sound, retune Tx & Rx as per instructions. See page 8. ii) Using the safety pin, attach the Tx to the pyjama top or nightdress close to the shoulder. Attach Tx to material before wearing garment if preferable. Carefully lock the safety pin. Do not use safety pin if faulty. Optional shoulder clip is available for clinics on request if safety pin use is unsuitable. iii) Thread sensor lead inside top as shown in diagram above. For small children, loop and tie sensor lead to shorten length. iv) Attach sensor clip to the outside of close fitting underwear (at the location where it is most likely to get wet first), by inserting the folded underpants material inside the front jaw of the clip then lowering the lever. (Lowering the lever without any dry material in the jaws will activate the Tx, trigger the Rx alarm and prevent the Rx from being reset). Lift the lever and press the reset button. Do not reset the Rx by switching off. Always use the reset button. MALEM UNIVERSAL Lock the Easy-Clip onto the material by pressing down the lever IMPORTANT: DO NOT PLACE ANY MATERIAL UNDER THE SECURING LEVER Place underwear material into mouth (jaws) at the front of the Easy-Clip 2 IMPORTANT: Regularly CLEAN Easy-Clip Sensor in soapy water, rinse and shake dry
5. If used with Standard Sensor (BT): a) Absorbent pad: i) Cut off one end of an absorbent pad such as sanitary or incontinence pad and insert the sensor in between the layers. ii) Anchor with crocodile clip to prevent sensor from being pulled out. Uncover the backing strip and stick Please note that sensor and clip the pad inside a pair of close fitting are gold plated pants, ensuring the sensor is located where it will come into contact with the flow of urine. b) Between two pairs of underpants: i) Sandwich between two pairs of cotton briefs (not boxer shorts). Anchor with crocodile clip. c) Within Y-front fold: i) Place sensor plate within Y-fronts fold and anchor by locating the crocodile clip on the outside of the waistband of the pants. Avoid nylon/polyester underwear. d) With pull-ups or nappies: i) Cut a small slit into the outside of the material and insert the sensor plate at a location close to the urine flow. Outer Pants Inner Pant Please make sure the sensor plate and the crocodile clip are attached between the two pairs of pants and MUST NOT come in contact with the skin 3
6. If used with Bed-Mat Sensor (BM): a) Under no circumstances should the transmitter (Tx) be attached to the users clothing when using a Bed-Mat. b) Place a clean and dry Bed-Mat correct side up over the mattress in the area which is normally wetted and gently tie down. See page 5. c) Cover the Bed-Mat with a Clean Dry Cotton sheet and/or Bath Towel and make the bed up as usual. Avoid nylon/polyester sheets as they can cause false alarms due to increased perspiration. Adjust cover thickness over the mat to suit. d) Do not place plastic sheets directly under the Bed-Mat as condensation will cause the alarm to trigger. (See diagram page 5) e) Attach the Bed-Mat wire to the Tx and place the Tx beside the bed. See page 17. f) Please tuck in the Bed-Mat wire so that it is not in the way for getting in and out of bed. g) Upon waking to the Rx, try to stop any more urine from being released and use the lavatory to completely empty the bladder. h) The Rx alarm sound can be stopped ONLY when the Bed-Mat wire is unlocked from the Tx and the reset button on the Rx is pressed. i) For reuse, the Bed-Mat must be wiped clean with detergent and dried then replaced in a freshly made bed, as before. j) To test the system, place a damp cloth across the foil tracks on the Bed-Mat. 4
WIRELESS ALARM TRANSMITTER MO15(Tx) Under NO circumstances should the transmitter (Tx) be attached to the users clothing when using a Bed-Mat. MALEM UNIVERSAL Holes for tying Bed-Mat to the mattress. If using a plastic protective mattress sheet place adhesive tape over the Bed-Mat lower contacts. Bath Towel Sheet Bed-Mat Mattress Use a BATH TOWEL to cover the Bed-Mat and cotton sheet. Adjust towel thickness to suit. Pillow Transmitter (Tx) Place cotton sheet over Bed-Mat. Tie Bed-Mat around mattress. Tuck wire from Bed-Mat to alarm away neatly to prevent tripping or entanglement. 5 Bedside table
Hints regarding the use of Bed-Mat: l l l l l l l l Press the reset button once, receiver alarm sound will stop. LED will continue to flash. If the Bed-Mat is not dried or disconnected, the alarm sound will start again within two minutes. Press and hold the reset button for two seconds to stop the alarm and turn off the LED. The Bed-Mat positively locks to the Tx to prevent accidental disconnection. However, it must be unlocked before attempting to reset the alarm. Please use a thicker cotton sheet or place a bath towel above the Bed-Mat if sweating is triggering the Tx prematurely. Avoid plastic and man-made fibres as they may cause static discharge and false alarm. Treat the Bed-Mat with care. Avoid folding it or jumping on it. Please replace the Bed-Mat with a new one if it has deteriorated and use a new one with each user. (National Guidelines) Please note that sleeping directly on an uncovered Bed-Mat or touching it by hand may trigger the Tx and sound the alarm. Do not place plastic sheets directly under the Bed-Mat as condensation may trigger the alarm. 7. If used with Wander-Mat Sensor (WM): a) Activation by applied pressure: place the Wander-Mat (WM) in the appropriate position depending on the way you wish to use it. The Wander-Mat can be placed beside the bed or near the door so that treading on the Mat will activate the Tx. Please place a door mat over the Wander-Mat so as not to trip over the Wander-Mat. Plug into the Tx and place away safely. See page 19. b) Activation by removal of pressure: place the Wander-Mat (WM) over the mattress but under the sheet, in a position so that the user is laying over it or place on a chair so that the user is sitting on it. Plug the Wander-Mat wire into the inverter then plug the inverter wire into the Tx and place Tx away safely. If the user gets out of bed or out of the chair, the Tx will be activated triggering the Rx sound and selected LED. c) Once the receiver (Rx) is triggered, the appropriate red LED will be flashing. The buzzer sound can be silenced by pressing the reset button on the top of the Rx. (Do not use the on/off switch to reset the Rx as this will damage the microprocessor). The activated LED will remain flashing. If the matched Tx remains active, the Rx will sound again after two minutes. Press and hold for 3 seconds to deactivate and switch LED off. 6
8. If used with Dialysis-Mat Sensor (DM): a) Select the correct side of the Mat with shiny tracks up. b) Place the Mat over the chair arm. c) Plug the Mat wire into the Transmitter, tuck the wire and place Tx out of the way in a safe place. See page 18. d) Test the Mat by placing a slightly wet tissue over the tracks. The Rx should sound. e) If sweating is likely to activate Tx and sound the alarm cover the Mat surface with tissue paper. Adjust thickness to suit. f) Rest patients arm over the Mat. g) Wipe Mat clean and dry before use again. 9. Deactivating the Transmitter: a) If using the Easy-Clip sensor, lift the sensor lever and remove from underpants (wash Easy-Clip sensor frequently). b) If using the Standard sensor, unclip the crocodile clip and remove the sensor, wipe sensor plate dry and clean regularly. c) If using the Bed-Mat, unplug the Bed-Mat from the Tx, remove the sheet, wipe clean and dry thoroughly before repositioning. d) If using the pressure/release Wander-Mat, unplug from the Tx and reposition the user on the Mat. c) If using the Dialysis-Mat, unplug from the Tx, clean and dry the Mat then, reposition. f) Press the reset button on the Rx to silence the buzzer. 10. Resetting the Rx Sound: a) Press and hold the reset button for 2 seconds to switch off the sound and de-activated LED/s (make sure matched Tx is not active). b) The matched Tx/Rx will not trigger the Rx if the Tx is activated within 2 minutes of previous activation. c) For easy identification, an adhesive label can be used on the front of the Rx where you can write the room number or occupant name for each of the seven LEDs. 7
Channel Selection see diagram on page 14 The Malem Universal ON Wireless Alarm consists of a receiver which can be paired with up to seven transmitters. To avoid interference 1 2 3 4 5 6 OFF from the 7 transmitters or other wireless equipment, you need to select different channel settings for each of the transmitters. A choice of 64 settings is possible and should be changed in case of interference. To change the channel setting, remove the back of the transmitter using a slotted screwdriver. Lower to open. Change the setting of the code selection switch (the one on the left) by moving any of the switches in any of the 64 combinations. Receiver LED Number Selection see diagram on page 14 To match a Tx with a specific Rx LED number, remove the battery cover of the Tx using a slotted screwdriver. The LED selection switch is the one on the right. Select the LED number by sliding the matching number (between 1 and 7) of the sliding switch to ON. Re-tune Tx and Rx. See below. Re-tuning the Rx and Tx see diagram on page 14 & 16 ON All additional transmitters will need to be re-tuned with the Rx. a) Select the desired Rx LED number first (see above). 1 2 3 4 5 6 7 8 OFF b) Push and release the straight end of a paper clip into the small LEFT hole at the back of the receiver. All the 7 LED s will glow. c) Immediately and while the LED s are glowing, activate the Tx you wish to tune/re-tune by lowering the Easy-Clip sensor lever or wetting the standard sensor or Bed-Mat or applying pressure on the Wander-Mat or wetting the Dialysis-Mat. d) The LED s will switch off apart from the selected one which will glow on and off. The next activation of the Tx will activate the Rx LED and the buzzer. e) Repeat for all other additional transmitters. f) Remember to change channel if you are experiencing any interference from other transmitters or wireless equipment. You can also tune several receivers to the same transmitters. This is helpful if more than one carer wants to monitor the transmitters. Sound Selection Switch see diagram on page 16 The receiver is factory set to 8 random sounds. For single sound selection: a) Open the Rx battery cover using a slotted screwdriver. Insert blade into slot and twist. b) Slide to ON any one of the switches between 1 and 8. c) Slide all other switches apart from 10 to the OFF position. d) Do not slide switch 10 to OFF as this will silence the Rx sound. 8
Important l Remove batteries from both Tx and Rx if not in use. l Observe clean battery compartment contacts and correct polarity when changing batteries. l Use long life alkaline batteries whenever possible. l Batteries should not be accessed by children and only replaced by adults. l Do not immerse the Tx or Rx in water. l Regularly clean the sensor in use. See page 10. l Do not leave the Tx active (LED on) as this will drain the battery. See page 13. l Do not use the receiver ON/OFF sliding switch as a reset button as this will damage the microprocessor. Always use the Reset button. Batteries (remove isolating tag if present) Batteries have been provided free of charge with original purchase to enable testing during manufacture and prior to packaging. Additional batteries can be purchased. Batteries should not be accessed by children and only replaced by adults. Use long life alkaline batteries whenever possible. Do not leave Tx active when not in use as this will drain the battery. Observe correct polarity and clean contacts when replacing Tx and Rx batteries. Tx: alkaline 23A 12V Rx: alkaline 3 x AA Replace batteries on the Tx or Rx if the LEDs are rapidly flashing. Safety pin Pull white cover slightly to unlock, push to lock, you can replace the safety pin by sliding the replacement bar to the left. See page 14. Guarantee Under normal usage, the Malem Universal Wireless Alarm is guaranteed for a period of three months from purchase. This excludes batteries, sensors, Bed-Mat, Wander-Mat, Dialysis-Mat, safety pin, flooding, misuse or accidental damage. If the alarm should malfunction during this period, please contact us before sending. Please remove the batteries and decontaminate the unit/s sensor before returning. Do not return flooded or contaminated alarms. Repairs If repairs are required, we will exchange for a new alarm (repairs are not untaken for health and hygiene reasons). Please contact us by telephone, e-mail or in writing for the cost of this service. Please decontaminate the units/s before return. Do not return contaminated or flooded alarms. 9
Cleaning Alarm units (Tx and Rx): Wipe clean alarm and safety pin using a damp cloth and mild detergent or skin disinfectant. NEVER IMMERSE IN WATER Sensors (wash regularly): Easy-Clip - lift lever, wash in warm soapy water, rinse under the tap and shake dry. Standard Sensor - wash in soapy water and dry thoroughly. Bed-Mat - wash in warm soapy water and wipe dry. Wander-Mat - wipe with damp cloth and mild detergent, dry thoroughly. Dialysis-Mat - wipe with damp cloth and mild detergent, dry thoroughly. National guidelines state one user per Sensor/Mat. Disposal At the end of the alarms working life, please dispose of the product at a special local authority differentiated waste collection centre. Fault Finding Alarm does not sound: a) Switch on receiver Rx. Green LED should flash. b) Replace batteries with new alkaline ones (3 x AA). Observe correct polarity orientation and make sure contacts inside the battery compartment are clean and free of any deposits. c) Sound selection switch has been wrongly set or switch No.10 has been set to OFF. Reset all switches to their original position as per diagram on page 16. d) Remember that the Rx will not sound again within 2 minutes of being activated by the Tx. However the Rx will be activated if other Tx is activated. The 2 minute delay is to allow the triggered Tx to be reset. If the Tx is not reset, then the Rx will sound again after 2 minutes if the reset button has been pressed to silence the buzzer. e) Does the Tx LED glow when the Tx is activated by lowering the lever on the Easy-Clip sensor or wetting the standard sensor or Bed- Mat/Dialysis-Mat or applying pressure on the Wander-Mat? If it does not glow, then replace the Tx battery (alkaline 23 A 12V). Observe correct polarity and clean contacts. f) Remove isolating tags from battery compartment in Tx and Rx. Retune Tx and Rx. If all fails, return Tx and Rx for investigation. Contact us before doing so. Decontaminate all units before returning. See diagram on pages 13 and 16. 10
Alarm does not reset: a) Clean Easy-Clip sensor by lifting lever, wash in warm soapy water, rinse under the tap and shake dry. Repeat if necessary. b) Make sure Easy-Clip sensor lever is NOT down without dry material between the front jaws. c) Clean Bed-Mat and dry thoroughly. Use thicker towel over Mat. Do not use man made sheets over the Mat. d) Clean Dialysis-Mat and dry thoroughly. Use thicker tissue paper or material under the arm. e) Remove pressure or apply pressure to Wander-Mat. f) Make sure underpants material is not too thin or wet. g) Replace Tx and/or Rx batteries. h) Transmitter is damaged or flooded. Sound level is too low: a) Adjust sound level with volume control. See diagram on page 15. LED flashing rapidly: a) Replace battery. Specifications MO15 Transmitter (Tx) Colour: red Weight: 33g including battery, 25g without battery Dimensions: length: 50mm width: 45mm depth: 21mm Range: approximately 25m depending on nature of the structure and the state of the battery. Battery cover: to remove, place a slotted screwdriver in the bottom slot and lower the handle. Battery: alkaline 23 A. Observe correct polarity when replacing and ensure no deposits are on the metal contacts. Safety pin: pull white cover slightly to unlock, push to lock, you can replace the safety pin by sliding the replacement bar to the left. Do not use faulty safety pin. Red LED: flashes when transmitter is active. Do not leave on for extended length of time as this will drain the battery. LED will flash rapidly for 3 minutes and then turn off when battery capacity is low. Replace battery. Frequency: 433 MHz Model: MO15 Tx Standards: and 11
Specifications MO15 Receiver (Rx) Colour: red Weight: 136g including batteries, 67g without batteries Dimensions: length: 91mm width: 72mm depth: 26mm Battery: 3 x AA alkaline. Observe correct polarity and clean contacts when replacing batteries. ON/OFF: sliding switch on side Volume: volume control wheel on the side. Turn up to increase and down to decrease. Reset button on the top will not reset if Tx is active. Press button and hold for 3 seconds to cancel active LED. Do not use ON/OFF button to reset the receiver. Green LED: flashes once every 2 seconds when Rx is ready for use. Red LED 1 to 7: ON when paired Tx is triggered. Up to 7 Txs can be tuned and paired to the 7 LEDs. Once an LED is activated, even paired ON, when reset, it will not be triggered again for 2 minutes. The LED and buzzer will be reactivated if the linked Tx remains active. Tuning point: 2 small pin holes on the back of the Rx. The one on the left is the tuning hole. Insert the straight end of a paper clip into the hole and press slightly then release, all the red LEDs will glow. While the red LEDs are on, activate the Tx. The LEDs will go off and only the LED which has been selected on the Tx will flash. When the Tx is activated again, the LED will flash and the buzzer will sound. Green LED will flash rapidly when battery capacity is low. Replace battery. Default hole: the small hole on the right on the back of the Rx is the default hole. Insert the straightened end of a paper clip and press gently then release. This will erase all the tuned memory. Re-tuning to the Tx/s will be required. Model: MO15 (Rx) Standard: and Sensors Easy-Clip : Length 79 cm. Keep lever up when not in use. Clean sensor regularly. Standard: Length 79 cm. Keep clean and wipe dry. The sensor plate and crocodile clip MUST NOT be in direct contact with the skin. Bed-Mat: 54 x 42 cm. Wire length 202 cm. Keep clean and wipe dry. Always cover with cotton sheet as well as a bath towel. Under no circumstances should the transmitter (Tx) be attached to user s clothing when used with a Bed-Mat. Wander-Mat: 75 x 40 cm. Wire 150 cm. Use pressure on or pressure off (for pressure off use with inverter ). Dialysis-Mat: 22 x 17 cm. Wire 100 cm. Keep clean and wipe dry. Malem Medical reserves the right to change specifications without prior notice. 2011 Malem Medical 12
Malem Universal Wireless Alarm Transmitter MODEL MO15 (Tx) Red LED flashes when Tx is active. Please do not leave on as this will drain the battery. If using the Easy-Clip sensor, please make sure the lever is up when not in use or unplug the sensor from the socket. MALEM UNIVERSAL WIRELESS ALARM TRANSMITTER MO15 (Tx) Sensor locking socket LED will flash rapidly for 3 minutes then turn off when the battery capacity is low. Replace battery. Use Alkaline batteries ONLY 13
Malem Universal Wireless Alarm Transmitter MODEL MO15 (Tx) ON ON 1 2 3 4 5 6 OFF Channel selection switch Safety pin replacement bar ON 1 2 3 4 5 6 7 8 OFF Receiver LED selection switch 1 2 3 4 5 6 OPEN ON 1 2 3 4 5 6 7 8 lock + 23A 12V ALKALINE - CHANNEL SELECTION SWITCH unlock Rx LED No. SELECTION SWITCH 23A 12V + - ALKALINE Safety pin slide cover sideways to lock or unlock Battery compartment To open place slotted screwdriver in slot and move handle down Use 1 x 23A 12V Alkaline batteries Please observe correct polarity when replacing batteries Sensor locking socket MODEL MO15(Tx) OPEN Use Alkaline batteries ONLY 14
Malem Universal Wireless Alarm Receiver MODEL MO15 (Rx) Mute/reset Buzzer Red LEDs 1-7 Each light corresponds to the transmitter it is paired with. MUTE / RESET BUZZER PRESS & HOLD FOR 3 SEC TO RESET Green standby LED/2 sec flashes. LED will flash rapidly when battery capacity is low. (Replace battery) Press and hold for 3 sec to reset Volume STANDBY LED/2 SEC OFF ON POWER 1 2 3 4 5 6 7 MALEM - + VOLUME UNIVERSAL WIRELESS ALARM RECEIVER (Rx) Attach a label to the front of the Rx to indicate LED number, room number or users name. Power OFF - ON. Please do not use on/off switch to reset alarm. This will damage the microprocessor. Use reset button. Use Alkaline batteries ONLY 15
ON 1 2 3 4 5 6 7 8 9 10 ON Malem Universal Wireless Alarm Receiver 1 2 3 4 5 6 7 8 9 10 OFF Tx Rx Pairing. Use end of paper clip. Pass into hole, press and release, all red LEDs On, activate required Tx while red LEDs are On, one of the LEDs will flash the same number as the switch number selected on Tx. Sound selection switch Switch 1-8 will select sounds 1-8. Switch 9 must be off for single sound. For 8 sounds switch 1 as well as 9 and 10 must be On. Sounds will be Off if switch 10 is in the Off position. MODEL MO15 (Rx) Tx Rx Pairing To reset and erase all pairing memory use paper clip. Insert the end of a paper clip into the hole. Only use default to erase all pairing memory. Press and hold for 3 seconds. All pairing with Tx will be lost. To open battery compartment place slotted screwdriver in the slot then twist. Tx Rx PAIRING DEFAULT AA ALKALINE SOUND SELECTION SWITCHES AA ALKALINE SEE INSTRUCTIONS FOR USE AA ALKALINE - USE 3 x AA + ALKALINE BATTERY + - - OPEN USE 3 x AA ALKALINE BATTERY USE 3 x AA + ALKALINE BATTERY Batteries: 3 x AA Please use alkaline. Observe correct polarity. Make sure metal contacts are clean. Use Alkaline batteries ONLY 16
Activation of the Tx using different sensors 1. Activation by Easy-Clip Sensor or Standard Sensor Malem Transmitter (Tx) Standard Sensor (BT) MALEM UNIVERSAL WIRELESS ALARM TRANSMITTER MO15 (Tx) Plug sensor into Tx socket Easy-Clip Sensor (EC) Lever - Keep up when not in use. Clean clip regulary. RJ10 plug 2. Activation using a Bed-Mat: 54 cm 42 cm 202 cm Malem Transmitter (Tx) RJ10 plug MALEM UNIVERSAL WIRELESS ALARM TRANSMITTER MO15 (Tx) Bed-Mat (BM) Bed-Mat connection wire Plug Bed-Mat RJ10 plug into the Malem transmitter socket 17
3. Activation using a Dialysis-Mat Malem Transmitter (Tx) 22 cm RJ10 plug MALEM UNIVERSAL WIRELESS ALARM TRANSMITTER MO15 (Tx) 17 cm Dialysis-Mat (DM) DM connection wire 100 cm Plug Dialysis Mat RJ10 plug into the Malem transmitter socket 18
Wander-Mat with inverter 4. Activation by applying pressure: 75 cm Malem Transmitter (Tx) 40 cm WANDER MAT RJ10 plug MALEM UNIVERSAL WIRELESS ALARM TRANSMITTER MO15 (Tx) Wander-Mat (WM) WM connection wire 150 cm Plug WM plug into Tx socket 5. Activation by removing pressure: (user must be lying in bed or sitting over WM in a chair) Malem Transmitter (Tx) WANDER MAT Wander-Mat (WM) RJ10 plug WM connection wire PM Inverter PRESSURE MAT INVERTOR MALEM Plug WM into inverter socket WM inverter wire MALEM UNIVERSAL WIRELESS ALARM TRANSMITTER MO15 (Tx) Plug inverter plug into Tx socket Please note that pressure must be applied to the Mat BEFORE attempting to set up the connection. 19
Malem Wander-Mat Inverter front: LED light MALEM WANDER MAT INVERTOR The RJ10 plugs into the transmitter (Tx) Battery test button The RJ10 Wander-Mat (WM) plug, plugs into the inverter socket Please plug in the inverter wire between the Wander-Mat and the transmitter. Battery test: press the button, LED will glow. If LED does not glow then change the battery. (Remove battery isolator if present) The inverter should be used ONLY if you wish to use the Wander-Mat to detect removal of pressure. Please do not immerse inverter or Mat in water. Use Alkaline batteries ONLY 20
Malem Wander-Mat Invertor back: Use slotted screwdriver to open. Place tip in slot and twist. RJ10 plug Battery test button 23A 12V + - ALKALINE RJ10 socket Please observe correct polarity. Contacts clean and battery not loose inside compartment. Pull metal contact to make good connection. Use only 23A 12V Alkaline battery. Use Alkaline batteries ONLY 21
FCC ID: U9FMO15 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: Changes or Modifications not expressly approved by the party responsible could void the user s authority to operate this device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/tv technician for help. Malem Medical, 10 Willow Holt, Lowdham Nottingham NG14 7EJ, England, UK Tel: + 44 (0)115 966 4440 Fax: + 44 (0)115 966 4672 E-mail: malem@malem.co.uk Web: www.malem.co.uk Web: www.malemmedical.co.uk Malem Medical 2011