Nest x Yale Lock Installation and Programming Guide Warning Status Indicator Settings Speaker Back button Check (Set / Continue) Low Battery Indicator Keypad Failsafe 9 volt Battery Connection (Use Alkaline battery) Before you begin DOWNLOAD THE BILT APP for step-by-step installation instructions & to register your product Battery Cover XXXX0000000 Strike Plate Deadbolt AA Alkaline Batteries Inside Lock Inside Mounting Plate Battery Cover Key FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT AND VOID THE FACTORY WARRANTY 1
Template CUT LINE 1" [25mm] Dia. For 1-3/4" [44.5mm] Thick Door 1" [25mm] Dia. For 1-3/8" [35mm] Thick Door FOLD OVER DOOR EDGE 2-3/4" [70mm] Backset 2-1/8" [54mm] Dia Thru Hole 2-3/8" [60mm] Backset 2-1/8" [54mm] Dia Thru Hole CAUTION: If printed from electronic file set print scale to 1:1 Measure ruler to check scale 2" 1" 0" 50mm 25mm 2" 3" 1" 0" 25mm 50mm 75mm Tools Needed Provided Fasteners Standard Phillips Head Screwdriver Tools necessary only for new doors or adjusting existing prep. Inside Lock Screws Drill Pencil Utility Knife Wood Mortise Chisel Tape Measure Level Silver for 2 to 2-1/4" Door Thickness OR Black Standard for 1-3/4" Door Thickness OR Green Strike Plate for and 1-3/8" Latch Screws Door Thickness Optional Security Strike Plate Screws 2
Before you begin, open door and remove your existing deadbolt. Before you begin, double check your door prep measurements. 2-3/8" or 2-3/4" (60mm or 70mm) Backset 2-1/8" (54mm) Diameter See Door Prep Template 5-1/2" (140mm) Standard Check clearance with lower hardware if this dimension is less than 5-1/2" (140mm). EXISTING EXISTING Before you begin, prepare door & frame. Necessary only for new doors or adjusting existing prep. See Door Prep Template 2-1/8" (54mm) Dia. Frame Frame 2-3/8" (60mm) or 2-3/4" (70mm) Backset 1" (25mm) Dia. Inside of Door 1" (25mm) Deep Drill holes 1/2 way through door then complete from other side to prevent splitting. 3
1 Installing Deadbolt 2-3/8" (60mm) Position 2-3/4" (70mm) Position UP OR UP 2-3/8" (60mm) Backset Mechanism (Horizontal Orientation) Press 2-3/4" (70mm) Backset Pull Bolt must be in retracted (unlocked) position. Mechanism will be horizontal. Note UP arrow on deadbolt. *Backset *2-3/8" (60mm) or 2-3/4" (70mm) 2 Installing Strike Plate Choose standard strike plate screws or security screws. Frame 4
3 Installing Keypad Bolt must be in retracted (unlocked) position. Note horizontal orientation of mechanism. Inside of Door Outside of Door 4 Installing Interior Mounting Plate Choose through bolt appropriate for your door thickness. See Page 3. Make sure plate and keypad are level before tightening through bolts. Inside of Door 5
5 Removing Battery Cover XXXX0000000 6 Attaching the Cable Make sure to connect cable with black mark side up. Secure cable in hooks. 6
XXXX0000000 7 Installing Inside Lock XXXX0000000 Make sure bolt is retracted. Make sure inside lock is properly seated onto bottom of mounting plate and excess cable is tucked into lock cavity. 8 Testing Operation Close door and check bolt operation. Bolt should rotate freely and easily. Go back to step 3 to recheck installation if there is resistance. 7
XXXX0000000 XXXX0000000 9 Installing Batteries/Handing the Lock Hi from Yale and Nest. Door must be closed prior to inserting batteries. Lock automatically calibrates itself for use after battery installation. 10 Installing Cover Programming Instructions Congratulations, you've installed the Nest x Yale Lock Touch Yale logo to wake lock. You will be guided to set up the Master Passcode by following the audio instructions on the lock. Once installation is complete, download the Nest App to add the lock to your Nest account. Failsafe 9 volt Battery Connection (Use Alkaline battery) Additional passcodes and further programming can be done in the Nest app. Note that the Master Passcode may also need to be set within the app. Once the Nest x Yale Lock is paired with the Nest app, 20 passcodes will be available for use. For written programming/troubleshooting instructions and instructions in other languages, visit www.shopyalehome.com/nestyalelock/info Product Support Tel: 1-855-213-5841 www.yalehome.com Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company. Yale is a registered trademark of Yale Security Inc., an ASSA ABLOY Group Company. Nest is a trademark of Nest Labs, Inc. Copyright 2018, Yale Security Inc., an ASSA ABLOY Group Company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. Certified ANSI/BHMA A156.36 Grade 2 Nest Labs Designed in the US nest.com Built in China Patent & TM: nest.com/legal/ip-and-other-notices Open source: nest.com/legal/compliance 8 ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience.