Notes: 1 Square = Foot / Feet Hydrogardening Bucket Systems Tsunami 6 Site Ebb & Flow Gro System Instruction Manual Featuring Titan Controls Oceanus 3 Controller VANCOUVER, WASHINGTON U.S.A. www.flo-n-gro.net Revision E 02/06/2015 Flo-n-Gro Part #111398 VANCOUVER, WASHINGTON U.S.A. www.flo-n-gro.net
Tsunami System Contents Warnings & Cautions Tsunami System Controlled by Oceanus 3 Built in Safeguard for your Plants Assembly Instructions System Test Instructions Operating Instructions Maintenance of the Tsunami System System Specifications Troubleshooting Tips Warranty Information Warnings & Cautions Read all instructions before filling or operating the Tsunami System. DO NOT remove 5 gallon Gro sites when the system is cycling water, flooding will occur. If you top off your reservoir, only do this when the system has completed the DRAIN cycle or flooding will occur. When using bug bombs or pesticides, remove or cover system to avoid corrosion or contamination. DO NOT attempt to repair the Oceanus 3, there all no serviceable parts and any tampering voids warranty DO NOT put paperclips, tools, etc. into Oceanus 3, possible electrocution may occur. Verify that your power source is 120 Volt ONLY before plugging in your Oceanus 3. Check that all pumps being operated by the Oceanus 3 are 120 volt only. The Oceanus 3 is designed for Inside Use Only. Avoid placing the Oceanus 3 near heat generating sources like CO 2 generators, heaters, etc. Use caution when operating Oceanus 3 in high humidity environments. DO NOT use Oceanus 3 for purposes other than the unit was designed to function. Ask your Dealer for tips and techniques when operating the Tsunami System Be environmentally conscientious when disposing on any expended nutrients or growing products. WARRANTY SERVICE: Please read warranty information first If after reviewing the troubleshooting tips the unit will still not work, you should return it to the Dealer where you purchased the controller. They will be able to further evaluate the unit and test its various components and quite possibly will be able to identify and/or fix any problems. If the Dealer is unable to fix the unit, they will return it to us for factory repair. If there are no Dealers in your area, you may contact us directly for technical support. If we cannot help you resolve the problem over the phone, we will issue you an RMA # (return merchandise authorization) authorizing you to return the unit to us for factory reconditioning (if the unit is under warranty). Contact the number below for an RMA # and shipping address. Complete the form below and include it with your unit. Also please write the RMA # on the outside of the box. Please package the unit in its original packaging. If it is damaged in shipment we cannot be responsible. Once we receive the unit back, we will repair or replace the controller within 48 hours (business) and return it to you freight prepaid via UPS ground shipment. Include the following if returning directly to Flo-n-Gro Proof of purchase This completed form RMA # on the outside of the box Return Merchandise Authorization Number (Required): Company Name: Contact Name: Address: Phone #: Email address: What is the nature of the problem? Shipping address will be given when the RMA # is issued. Hydrogardening Bucket Systems www.flo-n-gro.net For technical assistance call us at 1-888-808-4826. Representative available Monday Friday, 8 a.m. 5 p.m. PST. 2 11
Warranty Information Titan Controls warrants the original purchase of this product against defects in material and workmanship under normal use for one (1) year from the date of purchase. During the warranty period, Titan Controls will, at our option, and without charge, repair or replace this product if the controller or any of its components fail or malfunction. All returns or repairs must be accompanied by a Return Merchandise Authorization (RMA) number prior to any service of the product. This warranty is expressly in lieu of all other warranties, expressed or implied, including the warranties of merchantability and fitness for use and of all other obligations or liabilities on the part of the seller. This warranty shall not apply to this product or any part thereof which had been damaged by accident, abuse, misuse, modification, negligence, alteration or misapplication. Controllers with serial numbers or date tags that have been removed, altered or obliterated; broken seals or that show evidence of tampering; mismatched board serial numbers or nonconforming parts; are excluded from coverage. Titan Controls makes no warranty whatsoever in respect to accessories or parts not supplied by Titan Controls. Monetary refunds of the warranty will not be given. The Buyer assumes all responsibility regarding the use & installation of this controller. All warranty service is provided through the factory or an authorized service representative. This warranty shall apply only to the United States. Defective controllers need to be returned with the proof of purchase receipt. For additional warranty information, contact a Titan Controls Technical Service Representative. Our normal business hours are Monday Friday, 8 a.m. to 5 p.m. Pacific Standard Time. We are closed most major holidays. NOTE: Titan Controls is a controller manufacturer. All sales offerings to the public are done through a nationwide group of Dealers. No sales offerings will be made directly to the general public. Service and Repair Program For all service and repairs please contact one of our Technical Service Representatives for a Return Merchandise Authorization (RMA) number. All factory service & repairs will be completed within 48 hours after receipt of controller and after authorization by customer for repairs. Titan Controls will, at its discretion, repair or replace the controller. Returning Units: Please contact your retail store for returns. 10 Tsunami System Controlled by the Oceanus 3 As controlled by the Oceanus 3, the Tsunami System is the latest innovation in ebb and flow gardening: 1. Straight forward step by step assembly instruction printed in easy to read text with pictures, makes assembly a pleasure, not a pain. 2. With the disabled and physically impaired grower in mind, easy to attach tee fittings and tubes connect the entire system with no tools necessary. 3. Oxygen rich nutrient water floods the root zone and provides excellent air/water transfer. 4. Simple to operate by pushing time trippers to set any watering cycle that can be imagined. 5. Easily expandable Gro system by adding sites and moving EZ pull caps. Built In Safeguard for your Plants EXCLUSIVE BRAIN DRAIN FEATURE The Oceanus 3 includes the patented proprietary Titan Controls Brain Drain feature that accurately and consistently manages the DRAIN pump through digitally controlled mini cycles pumping out the exact amount of nutrient solution while leaving an emergency reserve at each Gro bucket to safeguard your plants against power outages or other unforeseen issues. Assembly Instructions STEP 1- Remove green factory seal from 55 gallon reservoir. STEP 2- Organize the Parts Become familiar with your Tsunami Systems components by removing and organizing your parts to make assembly easy and complete the following checklist: Flo-n-Gro Tsunami Grow System Components List ü QTY Part Name Part Description 1 Controller Oceanus 3 - Ebb & Flo controller with EZ Pull End Caps & 3 ¾ black tube 6 Outer Bucket 5 Gallon black bucket with grommet installed 6 Inner Bucket 5 Gallon black bucket with drain holes 2 Pump High quality pump 6 Tee ¾ tee fitting 2 ¾ Spool 10 spool of ¾ black tubing coil 6 ¾ Short 3 foot pieces of ¾ black tubing 6 Clamp ¾ black click clamps 1 Reservoir Blue 55 Gallon Reservoir with fittings and lid 3
Everything checked off? If yes, proceed to STEP 3. If you are missing anything or have any questions or problems, please call the Titan Controls technical phone line 1-888-808-4826. STEP 3 - Assembly and Set-Up Assemble Flood Lines 1. Place the 5 gallon inner bucket into the 5 gallon outer bucket. 2. Arrange the 5 gallon buckets to match the lighting footprint of your garden. (PHOTO #1) HINT It is important to remember that the black buckets must be at the same level as the Oceanus 3 for the system to function properly. HINT Consider locating the system close to a drain or available method of properly disposing of the old nutrients. 3. Insert 3/4 tees into outer black bucket. (PHOTO #2) 4. Connect ¾ short tubes between each black outer bucket at tee fittings to form desired number of flood lines. (PHOTO #3) Connect Oceanus 3 to the Flood Lines 5. Cut a length of ¾ tubing matching the desired distance between the Oceanus 3, and the first flood line. 6. Remove one of the black ¾ EZ pull end caps from one of the Oceanus 3 output fittings (the output fitting is located at the bottom of the Oceanus 3) and connect the first end of the ¾ cut tubing to the now exposed output fitting. 7. Connect the second end of the ¾ cut tubing to the front end of the flood line and take the just removed EZ pull end cap and slide it over the end of the last ¾ tee fitting at the end of the line. (See PHOTO 3 for example). 8. Repeat for each flood line. EZ pull end caps provide the ability to expand and contract your grow system and are necessary to prevent flooding. DO NOT DISCARD! Flooding will occur if you fail to cap each flood line. Connect Oceanus 3 To 1st Pump 9. Use the included 32 section of ¾ black tubing and attach it to the first pump outlet securing with a ¾ clamp. (PHOTO 4) PHOTO #1 PHOTO #2 PHOTO #3 PHOTO #4 Reservoir: Dimensions = 24 W x 37 H Total Water Volume = 55 US Gallons Gro Buckets: 5 US gallon outer bucket 5 US gallon inner bucket Oceanus 3 Controller: Dimensions = 13 W x 16 D x 19 H Weight = 7.5 lbs. Voltage Input = 120 Volts Voltage Output = 120 Volts Minimum Amperage =.25 Amps Maximum Amperage = 10 Amps Hertz = 60 Hz. Storage Temperature = 32 F to 125 F Operating Temperature = 45 F to 115 F Pump Specifications: See pump packaging for details System Specifications Troubleshooting Tips If your Tsunami System is not functioning as expected, try the following: 1. Verify all power sources, i.e. wall outlet, FILL outlet, DRAIN outlet and pumps to see that each is providing 120 Volt power. 2. Don t allow the reservoir to run dry. Try to keep at minimum of 50% full at all times. 3. Check and clean all fittings and tubing to insure that they are not clogged with roots or other debris. 4. If your pump is making noise but not pumping water, rock from side to side to release air bubbles trapped in the pump. This normally occurs when the pump runs dry. 5. Check our website or call our Tech Service Rep for more troubleshooting tips. 4 9
Maintenance of the Tsunami System: The nutrient solution in the Tsunami System will need to be changed approximately every 10 to 14 days based on your plants feeding requirements. In between water changes, you may top off your reservoir with fresh water or a reduced strength of nutrient solution. Consult nutrient manufactures feed chart or go on-line and research nutrient feeding regimens for more information. To insure your system is functioning properly: Regularly clean the debris filters on your pumps. Check all tubing for kinks or cracking. Verify that the white float switches in the Oceanus 3 are clean and free of obstructions. Inspect anti-siphon holes on FILL and DRAIN fittings on 55 gallon reservoir. Clean if necessary. Wipe down inside of Oceanus 3 and reservoir with towel to remove film and debris. FULLY CLEAN Tsunami system between each crop. Remove white float switches (making sure you properly orient them before replacing) and clean using white vinegar to remove corrosion. 10. Attach the other end of the 32 section of ¾ black tubing to the DRAIN fitting under the controller lid and secure with 3/4 clamp. (PHOTO 5) 11. Pull the power cord through the top lid on the Oceanus 3 and plug it into the DRAIN OUTLET on the side of the Oceanus 3 (PHOTO 6) Connect Reservoir to 2nd Pump 12. Cut a piece of ¾ black tubing that is long enough to reach from the ¾ FILL fitting to the bottom of the reservoir (Approximately 40 ) 13. Connect the first end of the ¾ black tubing to the 2nd pump outlet and lower the pump to the bottom of the reservoir. Use the ¾ clamp to secure tubing to pump. Then lower pump into bottom of reservoir (PHOTO 7) 14. Connect the other end of the ¾ tubing to the ¾ FILL fitting on the side of the reservoir and secure with the ¾ clamp. (PHOTO 8) Connect Reservoir to the Oceanus 3 15. Locate the reservoir where it will be easy to fill and in close proximity to the Oceanus 3 controller. 16. Take the Power cord from the pump through the hole in the lid of the reservoir and plug it into the FILL output on the Oceanus 3. (PHOTO 9) Drain Plug Fill PHOTO #9 PHOTO #8 PHOTO #7 PHOTO #6 PHOTO #5 17. Cut two (2) pieces of ¾ black tubing from the spool that are long enough to reach from the side of the reservoir to the ¾ fittings located on the top of the Oceanus 3 controller. (PHOTO 10) 18. Attach the first end of the cut ¾ black tubing to the DRAIN fitting on the side of the reservoir, secure with a ¾ clamp. Then attach the second of the ¾ black tubing to the DRAIN fitting on the top of the Oceanus 3 controller. (PHOTO 11) PHOTO #10 19. Attach the first end of the cut ¾ black tubing to the FILL fitting on the side of the reservoir, secure with a ¾ clamp. Then attach the second of the ¾ black tubing to the FILL fitting on the top of the Oceanus 3 controller. (PHOTO 11) PHOTO #11 8 5
System Test Instructions Suggested Tsunami System Pre-Use Test 1. Double check each fitting connection for a secure fit to prevent leaks! 2. Fill reservoir with warm water only. (The warm water will relax the black tubing) a. DO NOT put your growing media into the 5 gallon Gro buckets, as you will want to observe the water levels. b. DO NOT put your valuable nutrients into the reservoir, you may need to drain and fix something. 3. Plug the Oceanus 3 into a 120 Volt wall outlet. 4. Turn the minute hand clockwise just until the FILL cycle is initiated. a. You should hear the pump in the reservoir activated and running. b. You should see the GREEN LED on Oceanus 3 blinking for the FILL CYCLE. c. You should see the 5 gallon Gro sites filling with water until the upper float switch on the Oceanus 3 has floated up and stopped after reaching the upper position for 5 seconds. d. After the 5 seconds has elapsed, the reservoir pump will shut off. e. You should see a solid GREEN LED light indicating that the FILL CYCLE is complete. 5. Now, turn the minute hand clockwise again to initiate the DRAIN CYCLE. a. You should hear the pump in the Oceanus 3 come on. b. You should see the RED LED on the Oceanus 3 blinking for the DRAIN CYCLE. c. You should see the 5 gallon Gro sites draining water and pumping it back into the reservoir. d. A proprietary Brain Drain feature will manage the Oceanus 3 pump through a few extra cycles to pump out the exact amount of water leaving just enough in the Gro sites to maintain the seals at the tee fittings and safeguard your plants in case of a power outage. e. After the DRAIN CYCLE is complete, you will see a solid RED LED indicating that the DRAIN CYCLE is complete. f. You should see a small amount of water in each Gro site. Operating Instructions 1. First, unplug the Oceanus 3 from the 120 Volt wall outlet. 2. Fill up to 3 inches from the top of the inner bucket with your choice of hydroponic grow media. (We suggest using Hydroton grow media) 3. When transplanting starts, place the top of the transplant cube approximated 2 inches under the surface of the grow media to prevent the transplant from floating during FILL CYCLE. 4. Fill the reservoir with your choice of PH balanced hydroponic nutrient solution. 5. For longer periods between maintenance, fill the 55 gallon reservoir completely and place an air stone at the bottom of the reservoir to evenly mix nutrient solution. 6. Set the desired number of times for the FILL CYCLE by pushing the white time trippers to the inside of the ring (PHOTO 13). HINT Recommend 2 FILL CYCLES during daylight period only. First one hour after lights come on, and second FILL CYCLE one hour before lights go off. Add third FILL CYCLE in middle of the day after plants have matured. 7. Set the current time of day by advancing minute hand clockwise to the corresponding time of day. 8. There are FILL and DRAIN CYCLE LED s on the front of the Oceanus 3. a. The GREEN FILL CYCLE LED will blink slowly to begin with and then faster as the Tsunami System continues to fill. b. After the system is full of water the GREEN FILL LED light will be solid green. c. When the DRAIN CYCLE begins, the RED LED will begin to blink slowly, and then faster as the Tsunami System drains the water out. d. After the DRAIN CYCLE is complete, the RED DRAIN LED will be solid red. 9. After you have set the FILL CYCLES plug the Oceanus 3 into a 120 Volt power outlet. 10. The Tsunami System will now function based on your custom settings. 11. If both the FILL and DRAIN LED lights blink back and forth, unplug the Oceanus 3 from the 120 volt outlet, wait 10 seconds, synchronize timer with float switches, and plug the Oceanus 3 back into the 120 Volt power source. This will reset the Oceanus 3 controller. If you have successfully conducted the Pre-Use Test, proceed to the Operating Instructions. 6 7