Thermalright Macho 20 Rev.A
Macho 20 Rev.A Assembly package 7 5 Chill Factor 2g 2 8
Macho 20 Rev.A Intel 775/50/55/56/66 Exploded View Important! Before proceeding with installation, please check for the most up-to-date instructions at www.thermalright.com Macho Heatsink Body 20mm Fan Clip 20mm Fan M L6 Screw Anchoring Mount Anti-Vibration Pads Screw Nut Mounting Plate Intel Washer (small) M L0 Screw
Component 2 5 6 7 8 9 0 2 Chill Factor 2g Macho Heatsink Body Screw Nut 7 M L6 Screw 7 8 2 5 Anchoring Mount LGA20 Type B Screw Pillars x Intel Washer (small) 6 9 Mounting Plate M L0 Screw 5 AMD Washer (big) 0 Anti-Vibration Pad Screw driver 20mm Fan Clip 2 20mm Fan 2 Thermal paste The Ultimate Cooling Solutions! www.thermalright.com 2
Installation Instructions: Step : Step : Take out Macho cooler from the paper box. Remove the 20mm Fan from the cooler by pulling the Fan Clips upwards in order to give room for ease of installation. And leave the Fan Clips on the Heatsink Body. Do not remove them.apply Anti-Vibration Padding to corners on the Heatsink Body. Step 2: 2 Step 2 : Install the four screw pillars. Take one ML0 screw and put one washer for Intel around the screw pillar. Snap it through one of holes around CPU socket from bottom towards top. Cap the screw pillar with the screw nut included and then tighten up. Now repeat this installation for the other three screw pillars in a criss-cross pattern. Step : 2 Step : Place the Anchoring Mount on the Screw Nuts. Use the four ML6 screws to fix the Anchoring Mount on to the Screw Nuts.
Step : Chill Factor 2g Chill Factor 2g Step : Applying Thermal Paste Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly. Step 5: Step 6: Step 5: Mounting Plate Installation Place the Heatsink Body on top of the CPU. Make the Mounting Plate go through the Heatsink Body. Then use the supplied Screw Driver to fasten the two ML6 Screws to Secure the Mounting Plate. Step 6: Easy Access Pass the supplied Screw Driver through the central hole of the Heatsink Body, for easier access to the ML6 Screw underneath the cooler. Step 7: Step 8: Step 7 : Fan Installation Place the included 20mm fan onto the Heatsink Body. And then secure it with the 20mm Fan Clips, by pulling the Fan Clips to place the four ends at the four holes on the 20mm Fan. Step 8 : Installation completed Plug in the fan connector to the CPU PWM Fan socket on the motherboard. Installation complete. The Ultimate Cooling Solutions! www.thermalright.com
Macho 20 Rev.A Intel 20 Exploded View Important! Before proceeding with installation, please check for the most up-to-date instructions at www.thermalright.com Macho Heatsink Body 20mm Fan Clip 20mm Fan M L6 Screw Anti-Vibration Pads Anchoring Mount Mounting Plate LGA20 Type B Screw Pillars 5
Component 2 5 6 7 8 9 0 2 Chill Factor 2g Macho Heatsink Body Screw Nut 7 M L6 Screw 7 8 2 5 Anchoring Mount LGA20 Type B Screw Pillars x Intel Washer (small) 6 9 Mounting Plate M L0 Screw 5 AMD Washer (big) 0 Anti-Vibration Pad Screw driver 20mm Fan Clip 2 20mm Fan 2 Thermal paste The Ultimate Cooling Solutions! www.thermalright.com 6
Installation Instructions: Step : Step : Take out Macho cooler from the paper box. Remove the 20mm Fan from the cooler by pulling the Fan Clips upwards in order to give room for ease of installation. And leave the Fan Clips on the Heatsink Body. Do not remove them.apply Anti-Vibration Padding to corners on the Heatsink Body. Step 2: 2 Step 2 : Install the four screw pillars. Take one ML0 screw and put one washer for Intel around the screw pillar. Snap it through one of holes around CPU socket from bottom towards top. Cap the screw pillar with the screw nut included and then tighten up. Now repeat this installation for the other three screw pillars in a criss-cross pattern. Step : 2 Step : Place the Anchoring Mount on the Screw Nuts. Use the four ML6 screws to fix the Anchoring Mount on to the Screw Nuts. 7
Macho 20 Rev.A Step : Chill Factor 2g Chill Factor 2g Step : Applying Thermal Paste Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly. Step 5: Step 6: Step 5: Mounting Plate Installation Place the Heatsink Body on top of the CPU. Make the Mounting Plate go through the Heatsink Body. Then use the supplied Screw Driver to fasten the two ML6 Screws to Secure the Mounting Plate. Step 7: Step 8: Step 6: Easy Access Pass the supplied Screw Driver through the central hole of the Heatsink Body, for easier access to the ML6 Screw underneath the cooler. Step 7 : Fan Installation Place the included 20mm Fan onto the Heatsink Body. And then secure it with the 20mm Fan Clips, by pulling the Fan Clips to place the four ends at the four holes on the 20mm Fan. Step 8 : Installation completed Plug in the fan connector to the CPU PWM Fan socket on the motherboard. Installation complete. The Ultimate Cooling Solutions! www.thermalright.com 8
Macho 20 Rev.A AM2/AM2+/AM/AM+/FM/FM2 Exploded View Important! Before proceeding with installation, please check for the most up-to-date instructions at www.thermalright.com Macho Heatsink Body 20mm Fan Clip 20mm Fan M L6 Screw Anchoring Mount Anti-Vibration Pads Mounting Plate Screw Nut AMD Washer (big) M L0 Screw 9
Component 2 5 6 7 8 9 0 2 Chill Factor 2g Macho Heatsink Body Screw Nut 7 M L6 Screw 7 8 2 5 Anchoring Mount LGA20 Type B Screw Pillars x Intel Washer (small) 6 9 Mounting Plate M L0 Screw 5 AMD Washer (big) 0 Anti-Vibration Pad Screw driver 20mm Fan Clip 2 20mm Fan 2 Thermal paste The Ultimate Cooling Solutions! www.thermalright.com 0
Installation Instructions: Step : Step : Take out Macho cooler from the paper box. Remove the 20mm Fan from the cooler by pulling the Fan Clips upwards in order to give room for ease of installation. And leave the Fan Clips on the Heatsink Body. Do not remove them.apply Anti-Vibration Padding to corners on the Heatsink Body. Step 2: 2 Step 2 : Install the four screw pillars. Take one ML0 screw and put one washer for AMD around the screw pillar. Snap it through one of holes around CPU socket from bottom towards top. Cap the screw pillar with the screw nut included and then tighten up. Now repeat this installation for the other three screw pillars in a criss-cross pattern. Step : 2 Step : Place the Anchoring Mount on the Screw Nuts. Use the four ML6 screws to fix the Anchoring Mount on to the Screw Nuts.
Step : Chill Factor 2g Chill Factor 2g Step : Applying Thermal Paste Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly. Step 5: Step 6: Step 5: Mounting Plate Installation Place the Heatsink Body on top of the CPU. Make the Mounting Plate go through the Heatsink Body. Then use the supplied Screw Driver to fasten the two ML6 Screws to Secure the Mounting Plate. Step 7: Step 8: Step 6: Easy Access Pass the supplied Screw Driver through the central hole of the Heatsink Body, for easier access to the ML6 Screw underneath the cooler. Step 7 : Fan Installation Place the included 20mm fan onto the Heatsink Body. And then secure it with the 20mm Fan Clips, by pulling the Fan Clips to place the four ends at the four holes on the 20mm Fan. Step 8 : Installation completed Plug in the fan connector to the CPU PWM Fan socket on the motherboard. Installation complete. The Ultimate Cooling Solutions! www.thermalright.com 2
Macho 20 Rev.A Technical Spec Heatsink Specifications: Dimension: Length 20mm x Width 02mm x Height 50.5mm Weight: 6g (Heatsink only) Heatpipe: 6mm heatpipe*5 units Copper Base: C00 Pure copper nickel plated Fan Specification: Dimension: L20mm x H20mm x W25mm Weight: 50g Fan speed: 600~00RPM (PWM controlled) Fan noise: 25.dBA MAX (Test distance.0m) Airflow: 6.9CFM MAX Connector: Pin (PWM Fan connector)
Macho 20 Rev.A 20 6.6 05.5 02 0 0 0 5.85 The Ultimate Cooling Solutions! www.thermalright.com
Macho 20 Rev.A Awards 5
The Ultimate Cooling Solutions! www.thermalright.com TEL: +886-2-866-660 FAX: +886-2-866-665 EMAIL: sales@thermalright.com