E-ECGC-PL-010 REVISED STARTING SERIAL # 33 PARTS LIST MANUAL MODEL -EC and -GC Two-Disc Concrete Floor Grinder Page 1
E-ECGC-PL-010 READ AND UNDERSTAND THE OPERATORS INSTRUCTION MANUAL THOROUGHLY BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT. Death or serious injury could occur if this machine is used improperly.! SAFETY! MESSAGES The safety instructions are proceeded by a graphic alert message of DANGER, WARNING, or CAUTION. Indicates an imminent hazard which, if not avoided, will result in death or serious injury. Indicates an imminent hazard which, if not avoided, can result in death or serious injury. Indicates hazards which, if not avoided, could result in serious injury and or damage to the equipment. GASOLINE Powered Equipment Do not operate gasoline powered equipment without adequate ventilation. Carbon monoxide is an invisible, odorless gas that can kill. ELECTRICAL Powered Equipment ELECTRICAL HAZARD - Be sure equipment is properly grounded. Failure to comply could kill or result in serious injury. The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. GENERAL INSTRUCTIONS You must read and understand the operators instruction manual and all other manuals associated with this machine. For your safety and the safety of others around you, it is extremely important to fully understand how to operate this machine in the way it was intended. Different model machines or older/newer versions of the same model may have different parts and controls that you need to understand. If instructions are not readable or available DO NOT USE this machine and contact the factory for a replacement Manual. You must be able to physically handle the bulk weight and power of this machine. If not properly controlled this machine can cause death or serious injury. Do not operate this machine in an impaired mental state. You must be able to exercise good judgement and reactions to maintain a safe working environment. This is a one person machine which means only one operator can be operating the machine at any one time. For the safety of others, maintain a safe operating distance to other personnel. Your work area should be defined and appropriately marked so bystanders and coworkers do not stand or walk near this machine and end up seriously injured by flying debris or exposing them to harmful noise or dust. This equipment is for Commercial use. Although this is a one person machine your work team should understand how to shut this machine off and quickly get medical help if an accident strikes the operator. Keep all guards in place during operation. The guards are to provide protection from inadvertent contact with dangerous moving parts, pinch points, or hot surfaces. Wear appropriate Personal Protective Equipment (PPE) including safety glasses, safety boots, work gloves, respiratory protection, hearing protection, and head protection. Do not wear loose clothing that can get tangled in moving parts. Failure to do so could result in dismemberment or death. Wear an approved respirator when removing hazardous materials or when grinding/cutting dry materials. Some dust particles such as concrete dust can contain silicate particles which can cause silicosis (a very serious lung disease). Contact NIOSH or OSHA for further details. When wet grinding/ cutting, avoid contact with the concrete/asphalt slurry which can cause serious skin irritations. You must maintain this machine per the maintenance schedule in the operator manual. Remember before adjusting, servicing, or fueling this machine, disconnect the source of power to the machine by disconnecting the spark plug (Gas models), or by unplugging the electrical power cord (electric models) or air hose (Pneumatic models) AT THE MACHINE so you can assure yourself it remains unplugged while you are working on it. Do not modify this machine. Use only genuine EDCO parts and accessories. Repairs and service should be performed by approved EDCO dealers or authorized technicians. You should look carefully around the area before you begin work so you can identify potential hazards such as deck inserts, pipes, columns, openings, electrical cords or outlets, or any other objects protruding from the slab surface. This machine has no brain so you must use your own. There is no substitute for safety. The safety decals on the machine are to serve as a reminder for information you must already know before you begin using this machine. Take a moment to reread the safety decals each time you use the machine. If your machine is missing any decals, contact the factory for a replacement (EDCO 1-800- 38-33). Page
Section PARTS LIST MANUAL EDCO MODELS -EC and -GC Page Number E-ECGC-PL-010 Safety Messages & General Instructions................................ How To Order Replacement Parts..................................... 3 Illustration 1: Main Grouping........................................., Illustration : Multi-Accessory Disc Grouping............................ Illustration 3: Optional Pad Driver Disc Grouping......................... Illustration : Optional Surfacer Disc Grouping........................... 8 Illustration : Water Valve Grouping................................... 9 Illustration : Engine & Belt Drive Grouping (. HP)..................... 10,11 Illustration : Engine & Belt Drive Grouping (11 HP)...................... 1,13 Illustration 8: Propane Option........................................ 1,1 Illustration 9: Motor & Belt Drive Grouping (1.& HP)..................... 1,1 Illustration 10: Motor & Belt Drive Grouping (3 HP)....................... 18,19 Limited Equipment Warranty........................................ back cover -DISC CONCRETE FLOOR GRINDER PART NO. MODEL POWER OPTION 1800 GC-.H HONDA. HP, GASOLINE 100 GC-11H HONDA 11.0 HP, GASOLINE 800 GC-11P HONDA 11.0 HP, PROPANE 0800 EC-3B BALDOR 3.0HP-1 PHASE-0HZ-30V 0100 EC-1.B BALDOR 1.HP-1 PHASE-0HZ-11/30V 1300 (EXPORT) EC-B/0H BALDOR.0HP-1 PHASE-0HZ-0V HOW TO ORDER REPLACEMENT PARTS To insure product safety and reliability, always use genuine EDCO replacement parts when making repairs to the equipment. When calling for parts, specify the MODEL and SERIAL NUMBER of the machine which can be found on the NAME PLATE. Keep that information in the space provided. In addition to this information, give part number, description and quantity as listed on the parts list to your parts representative. Please note: Due to improvements and changes in the equipment, the illustrations shown may be different than the actual machine. FILL IN INFORMATION BELOW Date of Purchase Name of Machine Model # Serial # Belt Size(s) Toll Free: 1-800-38-33 FAX: 1-800--33 email: sales@edcoinc.com www.edcoinc.com Page 3
E-ECGC-PL-010 ILLUSTRATION 1 : MAIN GROUPING 9 8 1 13 1 1 18 1 1 10 9 19 1 11 1 3 0 8 3 3 1 30 9 1 0 9 8 31 1 19 1 1 1 18 3 1 3 33 3 3 0 39 38 3 3 Page
E-ECGC-PL-010 PARTS LISTING - ILLUSTRATION 1 : MAIN GROUPING ITEM# PART# DESCRIPTION QTY. 1 010 HANDLE BAR 1 1108 GRIP, HAND 1" MODEL SX 3 1009 SCREW, CAP 3/8- X 1-3/ 100 WASHER, FLAT 3/8 8 1000 NUT, LOCK 3/8-0 HOOD, GRINDER 1 1080 BOLT, TAP 1/-0 X 1-1/ 8 10013 NUT 1/-0 9 100 WASHER, FLAT 1/ 10 1081 NUT, KEPS 1/-0 11 00 COVER, GEAR CASE 1 1 10018 SCREW, CAP 1/-0 X 3/ 10 13 10038 WASHER, LOCK 1/ 10 1 100 WASHER, FLAT 1/ 10 1 1000 PLUG, HOLE /8" (CHROME) 1 1 008 BEARING, BALL 1" -HOLE FLANGE, ND 1 100 WASHER, LOCK /1 1 18 1081 NUT /1-0 1 19 009 BEARING, BALL 3/" -HOLE FLANGE 0 10309 SCREW, CAP 3/8-x1-1/ 1 10811 WASHER, LOCK 3/8 8 1001 NUT 3/8-8 3 01 GEAR, SPUR 11 TOOTH 013 SHAFT, LARGE GEAR 1"DIA X -13/1"L 1000 PIN, ROLL 3/8 X -1/ 03 GEAR, SPUR TOOTH (PINION) 1 011 SHAFT, PINION GEAR 3/DIA X -3/8"L 1 8 1003 PIN, ROLL 1/ X 1-1/ 1 9 10009 WASHER, FLAT 3/ 1 30 0 MAIN FRAME & GEAR CASE 1 31 001 CG8 DUST & SAFETY SHIELD (SKIRT) 1 3 1080 SCREW, CAP /1-18x1 1 33 10801 WASHER, LOCK /1 1 3 1013 WASHER, FLAT /1 1 3 9999 DISC ASSY. COMPLETE, MULTI-ACCY. LH 1 (SEE ILLUSTRATION FOR BREAKDOWN) 3 1003 PIN, ROLL 3/8 X 3 8888 DISC ASSY. COMPLETE, MULTI-ACCY. RH 1 (SEE ILLUSTRATION FOR BREAKDOWN) 38 1080 SCREW, CAP /1-18 X 1 39 10801 WASHER, LOCK /1 0 1013 WASHER, FLAT /1 1 10113 SPACER, STEEL 9/1OD X 3/8ID X /3" 11 PANEL, VACUUM PORT " 1 3 01 PLUG, CAP " 1 1031 SCREW, CAP 1/-0 X 1-1/ 1031 WASHER, FLAT 1/ 100 NUT, LOCK 1/-0 830 FLIP-HOLDER, WHEEL AXLE 8 10139 SCREW, SET 1/-0x/1 9 1 SPACER, WHEEL 3/8"L 1 0 9013 WHEEL 8 X -1/ X 3/"BRG. 1 1 AXLE SPACER 9-13/1"L 1 1 09 AXLE SHAFT 3/"DIA. X 1"L 1 Page
E-ECGC-PL-010 ILLUSTRATION : MULTI-ACCESSORY DISC GROUPING 8 3 1 8 #8888 DISC ASSEMBLY COMPLETE, RIGHT HAND (1 REQ D.) #9999 DISC ASSEMBLY COMPLETE, LEFT HAND (1 REQ D.) ITEM # PART# DESCRIPTION QTY. 1 DISC, MULTI-ACCESSORY 088 R.H. FOR #8888 ASSY. 1 099 L.H. FOR #9999 ASSY. 1 00 RING, HUB CARRIER, -HOLE 1 3 1011 RING, NEOPRENE, -1/ ODx1/"THK 010 HUB, ALUMINUM -HOLE (GRINDER) 1 1011 SCREW, SKT. HD. CAP 3/8- X -1/ 10113 SPACER, STEEL 9/1OD X 3/8ID X /3" 10011 SPACER, STEEL /8OD X 3/8ID X 3/8 8 1000 NUT, LOCK 3/8- Page
E-ECGC-PL-010 ILLUSTRATION 3 : OPTIONAL PAD DRIVER DISC GROUPING MULTI ACCESSORY DISC ASSEMBLY (SEE ILLUSTRATION FOR BREAKDOWN) 1 3 ITEM # PART# DESCRIPTION QTY. 1 00 PAD DRIVER DISC ASSEMBLY (INCLUDES ITEMS -) 0 HUB STUD, PAD DRIVER 1 3 01 DISC ONLY 11", PAD DRIVER 1 1031 WASHER, FLAT 1/ 1 1030 SCREW, CAP 1/-0 X 1 1 13013 SILABIDE PAD, 11" MEDIUM Page
E-ECGC-PL-010 ILLUSTRATION : OPTIONAL SURFACER DISC GROUPING 8 3 9 10 13 1 1 18 1 8 11 1 0 1 1 1 ITEM# PART# DESCRIPTION QTY. 1 DISC, SURFACER 1 R.H. FOR # ASSY. 1 133 L.H. FOR #3333 ASSY. 1 1011 RING, NEOPRENE, -1/ ODx1/"THK 3 00 RING, HUB CARRIER, -HOLE 1 010T HUB, CAST IRON -HOLE 1 1011 SCREW, SKT. HD. CAP 3/8- X -1/ 10113 SPACER, STEEL 9/1OD X 3/8ID X /3" 3 10011 SPACER, STEEL /8OD X 3/8ID X 3/8 8 1000 NUT, LOCK 3/8-9 100 NUT /1-18 1 10 10801 WASHER, LOCK /1 1 11 1080 SCREW, CAP /1-18 X 1 1 # SURFACER DISC ASSEMBLY, RIGHT HAND (1 REQ D) #3333 SURFACER DISC ASSEMBLY, LEFT HAND (1 REQ D) 19 ITEM# PART# DESCRIPTION QTY. 1 0 HOLDER, CUTTER SHAFT, SURFACER DISC 3 13 1080 BOLT, CARRIAGE 3/8-1 X 1 3 1 10089 CLIP, SPEED NUT 3/8" 3 1 100 WASHER, FLAT 3/8 3 1 10811 WASHER, LOCK 3/8 3 1 100 NUT 3/8-1 3 18 0 RETAINER, CUTTER SHAFT, SURF. DISC 3 19 08 CG CUTTER SHAFT, 1/ X 3-1/ 3 0 130 CG SPACER 1/"ID 33 1 CUTTER WHEEL 10 JRS01-P, POINTED (STANDARD) 01 CP0T, 1-3/" CARBIDE (OPTIONAL) 18 Page 8
E-ECGC-PL-010 ILLUSTRATION : WATER VALVE GROUPING ITEM# PART# DESCRIPTION QTY. 1 0A VALVE SUBASSY., w/ BRACKET 1 (INCL. ITEMS -) 0 BRACKET, WATER VALVE 1 3 1011 VALVE, BALL 1/ FPT 1 8001 CONN., SWIVEL FEMALE 3/ HOSE x 1/ MPT 1 1000 WASHER, HOSE 3/ (INCLUDED W/ CONNECTOR) 1099 BARB ELBOW 90 3/8 HOSE x 1/ MPT 1 108 SCREW, CAP STSHW 1/-0 X 1/ 009 CLAMP, HOSE, SAE #, ADJ. to 13/1 8 081 HOSE, WATER 3/8 ID x 3 L 1 9 109 BARB, 3/8 HOSE x 1/8 MPT 1 10 10 ELBOW, STREET 1/8 NPT x (BRASS) 11 1098 TIE, CABLE, BLACK NYLON 11-1/ Page 9
E-ECGC-PL-010 ILLUSTRATION : ENGINE & BELT DRIVE GROUPING (. HP) 3 1 13 8 1 0 19 1 11 10 3 18 1 1 9 1 1 Page 10
E-ECGC-PL-010 PARTS LISTING - ILLUSTRATION : ENGINE & BELT DRIVE GROUPING (. HP) ITEM# PART# DESCRIPTION QTY. 1 00 ENGINE, HONDA. HP GXV10KN1 1 03 MOUNT, ENGINE 1 3 1008 SCREW, CAP /1- X 3/ 3 10801 WASHER, LOCK /1 3 103 SCREW, CAP /1-18 X 1-1/ 1 100 WASHER, FLAT 3/8 10811 WASHER, LOCK 3/8 1 8 100 NUT /1-18 1 9 1080 BOLT, CARRIAGE 3/8-1 X 1 10 100 WASHER, FLAT 3/8 11 10811 WASHER, LOCK 3/8 1 100 NUT 3/8-1 13 0010 SWITCH KIT, STOP BUTTON, /8" HOLE 1 1 0 CLUTCH, CENTRIFUGAL 3. X 1GR X /8 1 1 10019 KEY, WOODRUFF /3 X /8 (#0) 1 1 3 SHEAVE "OD X 1GR.B X 3/"BORE 1 1 1001 KEY 3/1SQ X 1-1/ 1 18 1001 BELT L-0 1 19 111 BARB, PUSH-ON 3/8HOSEX10MMX1. 1 0 10 HOSE, PUSH-ON 3/8"ID X -1/"L 1 1 11 BARB, PUSH-ON 3/8HOSE X 1/FPT 1 10 PIPE PLUG 1/ NPT (BRASS) 1 3 1098 TIE, CABLE, BLACK NYLON 11-1/" 1 108 SCREW, CAP STSHW 10- X 1/ 0388 CABLE, THROTTLE, LEVER-TYPE " 1 Page 11
E-ECGC-PL-010 ILLUSTRATION : ENGINE & BELT DRIVE GROUPING (11 HP) 3 1 13 8 1 0 19 1 11 10 3 18 1 1 9 1 1 Page 1
E-ECGC-PL-010 PARTS LISTING - ILLUSTRATION : ENGINE & BELT DRIVE GROUPING (11 HP) ITEM# PART# DESCRIPTION QTY. 1 00 ENGINE, HONDA 11 HP GXV30K-DX3 1 03 MOUNT, ENGINE 1 3 1008 SCREW, CAP /1- X 3/ 10801 WASHER, LOCK /1 100 SCREW, CAP /1-18 X 1-1/ 1013 WASHER, FLAT /1 10801 WASHER, LOCK /1 8 100 NUT /1-18 9 1080 BOLT, CARRIAGE 3/8-1 X 1 10 100 WASHER, FLAT 3/8 11 10811 WASHER, LOCK 3/8 1 100 NUT 3/8-1 13 0010 SWITCH KIT, STOP BUTTON, /8" HOLE 1 1 0 CLUTCH, CENTRIFUGAL 3. X GR X 1 1 1 1030 KEY 1/SQ X -1/ 1 1 08 SHEAVE "OD X GR.B X 3/"BORE 1 1 1001 KEY 3/1SQ X 1-1/ 1 18 1001 BELT L-0 19 113 BARB, PUSH-ON 3/8HOSEX0MMX1.0 1 0 11 HOSE, PUSH-ON 3/8"ID X 3"L 1 1 11 BARB, PUSH-ON 3/8HOSE X 1/FPT 1 10 PIPE PLUG 1/ NPT (BRASS) 1 3 1098 TIE, CABLE, BLACK NYLON 11-1/" 1 108 SCREW, CAP STSHW 10- X 1/ 0388 CABLE, THROTTLE, LEVER-TYPE " 1 Page 13
8 E-ECGC-PL-010 ILLUSTRATION 8 : PROPANE OPTION 10 TO VACUUM NIPPLE BOTTOM OF CARBURETOR 1 1 TO SPUD-IN ON CARBUETOR 1 13 11 18 1 1 19 1 3 0 8 9 1 30 9 TO BEAM 0B REGULATOR 3 Page 1
E-ECGC-PL-010 PARTS LISTING - ILLUSTRATION 8 : PROPANE OPTION ITEM# PART# DESCRIPTION QTY. 1 101 ENGINE, HONDA 11. HP GXV30-DAP 1 11 STARTER KIT, ELECTRIC 10 VOLT AC 1 3 10031 SCREW, CAP 1/-0 X 1 100 WASHER, FLAT 1/ 1081 NUT, KEPS 1/-0 SCREW, CAP M X 1.0P X 18MM 10038 WASHER, LOCK 1/ 8 100 WASHER, FLAT 1/ 9 1 NUT M X 1.0MM PITCH 10 110 VAPOR KIT FOR HONDA GXV30-DAP 1 11 03 PROPANE REGULATOR MOUNT PLATE 1 1 108 SCREW, CAP STSHW 1/-0 X 1/ 13 10038 WASHER, LOCK 1/ 1 1130 PROPANE TANK 0LB. HORZ. 1 1 911 DECAL, ARROW, RED, 3 X 3 1 1 01 PROPANE TANK MOUNT COMPLETE 1 (INCLUDES ITEMS 1-) 1 01- PROPANE TANK STRAP W/ HINGE 1 18 01- PROPANE TANK TOGGLE CLAMP 1 19 01-1 PROPANE TANK CRADDLE BRACKET ONLY 1 0 01-3 PROPANE TANK CLAW BRACKET 1 1 111 SCREW, FLAT HD SLOTTED 1/-0 X 1 1081 NUT, KEPS 1/-0 3 1080 BOLT, CARRIAGE 3/8-1 X 1 0 PROPANE TANK MOUNT 1 100 WASHER, FLAT 3/8 10811 WASHER, LOCK 3/8 100 NUT 3/8-1 8 10908 BOLT, CARRIAGE 3/8-1 X -1/ 9 100 WASHER, FLAT 3/8 30 10810 NUT, LOCK 3/8-1 Page 1
E-ECGC-PL-010 ILLUSTRATION 9 : MOTOR & BELT DRIVE GROUPING (1. & HP) 30 1 0 9 18 19 1 3 0 1 8 11 10 9 8 3 1 1 1 13 1 Page 1
E-ECGC-PL-010 PARTS LISTING - ILLUSTRATION 9 : MOTOR & BELT DRIVE GROUPING (1.& HP) ITEM# PART# DESCRIPTION QTY. 1 MOTOR, BALDOR 1 0 1.HP-1 PHASE-0HZ-11/30V 1RPM 1019.0HP-1 PHASE-0HZ-110/0V 1RPM (EXPORT MODEL) 03 MOUNT, MOTOR 1 3 1001 SCREW, CAP 3/8- X 1 100 WASHER, FLAT 3/8 10811 WASHER, LOCK 3/8 1001 NUT 3/8-1080 BOLT, CARRIAGE 3/8-1 X 1 8 100 WASHER, FLAT 3/8 8 9 10811 WASHER, LOCK 3/8 10 100 NUT 3/8-1 11 1000 PLUG, HOLE /8" (CHROME) 1 1 SHEAVE 1 01 3"OD X 1GR.B X /8"BORE (USE ON 1. HP MODELS) 030 3"OD X 1GR.B X 1-1/8"BORE (USE ON.0 HP MODELS) 13 ------ KEY 3/1 SQ. (INCLUDED WITH MOTOR) 1 1 3 SHEAVE "OD X 1GR.B X 3/"BORE 1 1 1001 KEY 3/1SQ X 1-1/ 1 1 1001 BELT L-0 1 1 00 SWITCH, TOGGLE DPDT (VOLTAGE SELECTOR) 1 USED ON 1. HP MOTOR ONLY 18 08 SWITCH & WIRE HARNESS ASSY. 1 (INCLUDES ITEMS 19 THRU ) 19 03 SWITCH, ROTARY CAM ON/OFF, LOVATO 1 INCLUDES () 1/ NPT ADAPTERS 0 1130 STRAIN RELIEF 1/NPT X.0-.0" 1 0 PLUG W/ 1/3 WIRE HARNESS, LOCKING 1 0 BRACKET, LOVATO SWITCH BOX 1 3 113 SCREW, MACHINE 8-3 X 1/ (LOCATED INSIDE SWITCH BOX) 101 WASHER, LOCK, INT. TOOTH #8 10 NUT 8-3 0 WIRE HARNESS, 1/3 X 39"LOA 1 * 1098 TIE, CABLE, BLACK NYLON 11-1/" *8 1099 STRAIN RELIEF 3/NPT X.0-.0" 1 *9 108 SCREW, CAP STSHW 1/-0 X 1/ *30 0000 PLUG CONNECTOR, LOCKING 0A/0V 1 *NOTE: ITEMS THRU 30 ARE NOT INCLUDED WITH ASSEMBLY Page 1
E-ECGC-PL-010 ILLUSTRATION 10 : MOTOR & BELT DRIVE GROUPING (3 HP) 30 9 8 18 3 19 1 1 1 19 18 0 1 18 1 10 98 3 1 1 13 1 11 Page 18
E-ECGC-PL-010 PARTS LISTING - ILLUSTRATION 10 : MOTOR & BELT DRIVE GROUPING (3 HP) ITEM# PART# DESCRIPTION QTY. 1 1003 MOTOR, BALDOR 3HP-1PH 0HZ-30V 1RPM 1 03 MOUNT, MOTOR 1 3 1001 SCREW, CAP 3/8- X 1 100 WASHER, FLAT 3/8 8 10811 WASHER, LOCK 3/8 1001 NUT 3/8-1080 BOLT, CARRIAGE 3/8-1 X 1 8 100 WASHER, FLAT 3/8 9 10811 WASHER, LOCK 3/8 10 100 NUT 3/8-1 11 903 SHEAVE 3"OD X GR.B X 1-1/8"BORE 1 1 ------- KEY 1/SQ. (INCLUDED WITH MOTOR) 1 13 08 SHEAVE "OD X GR.B X 3/"BORE 1 1 1001 KEY 3/1SQ X 1-1/ 1 1 1001 BELT L-0 1 1000 PLUG, HOLE /8" (CHROME) 1 1 100 CONDUIT LOCK NUT 3/ NP 3 18 100 STRAIN RELIEF 3/NPT X.0-.0" 3 19 081 WASHER, FLAT 1-9/1 X 1-1/1 X.0 0 08 WIRE HARNESS 1/3 X 0"LOA, STARTER TO MOTOR 1 1 10 STARTER 11-M1-BRF-P3-3-300 1 103 SCREW, MACHINE 8-3 X 3/ 3 101 WASHER, LOCK, INT. TOOTH #8 10 NUT 8-3 108 SCREW, CAP STSHW 1/-0 X 1/ 10038 WASHER, LOCK 1/ 80 MOUNTING BRKT., LOVATO STARTER 1 8 083 WIRE HARNESS 1/3 X 0"LOA, STARTER TO PLUG 1 9 003 PLUG, LOCKING 0A/0V 1 30 0000 PLUG CONNECTOR, LOCKING 0A/0V 1 Page 19
E-ECGC-PL-010 LIMITED EQUIPMENT WARRANTY Equipment Development Company, Inc. herein referred to as EDCO warrants that each new unit manufactured by EDCO to be free from defects in material and workmanship in normal use and service for a period of (1) one year (except in the case of the cutter drum assembly on all model concrete asphalt planes, in which case the warranty period shall be 90 days) from date of shipment to the original retail or equipment rental center owner. EDCO will, at its option, repair or replace, at the EDCO factory or at a point designated by EDCO any part, which shall appear to the satisfaction of EDCO inspection to have been defective in material or workmanship. This warranty, does not apply to failure occurring as a result of abuse, misuse, negligent repairs, corrosion, erosion, normal wear and tear, alterations or modifications made to the product without express written consent of EDCO: or failure to follow the recommended operating practices and maintenance procedures as provided in the products operating and maintenance manuals. This warranty does not obligate EDCO to bear any transportation charges in connection with the replacement or repair of defective parts. This warranty does not obligate EDCO to bear any expense for travel time or of personnel in connection with any service calls. Accessories or equipment furnished and installed on the product by EDCO but manufactured by others, including but not limited to engines, motors, electrical equipment, transmissions, etc., shall carry the accessory manufacturers own warranty. THIS WARRANTY IS IN LIEU OF ALL OTHER WAR- RANTIES, EXPRESSED OR IMPLIED, OR STATU- TORY, INCLUDING ANY WARRANTIES OF MER- CHANTABILITY OR OF FITNESS FOR A PARTICU- LAR PURPOSE. LIABILITY LIMITATIONS The remedies of the user set forth under provisions of warranty outlined above are the exclusive and total liability of EDCO with the respect to their sale or the equipment and service furnished hereunder, in connection with the performance or breach thereof, or from the sale, delivery, installation, repair or technical direction covered by or furnished under the sale, whether based on contract, warranty, negligence, indemnity, strict liability, or otherwise shall not exceed the purchase price of the unit of equipment upon which such liability is based. EDCO will not in any event be liable to the user, any successors in interest or any beneficiary or assignee relating to this sale for any consequential, incidental, indirect, special or punitive damages arising out of this sale or any breach thereof, or any defects on, or failure of, or malfunction of the equipment under this sale based upon loss of use, lost profits or revenue, interest, lost goodwill, work stoppage, impairment of other goods, loss by reason of shutdown or non-operation, increased expenses of operation of the equipment, cost of purchase or replacement power of claims of users or customers of the user for service interruption whether or not such loss or damage is based on contract, warranty, negligence, indemnity, strict liability, or otherwise. EDCO reserves the right to modify, alter and improve any part or parts without incurring any obligation to replace any part or parts previously sold without such modified, altered or improved part or parts. No person is authorized to give any other warranty or to assume any additional obligation on EDCO s behalf unless made in writing and signed by an officer of EDCO. Equipment Development Company, Inc. USE ONLY GENUINE EDCO PARTS AND ACCESSORIES For your own safety, the safety of others and the life of your machine Page 0
E-ECGC-PLA-10 SKIRT KIT W/ RUBBER SEALS AND REMOTE VACUUM PORT FOR DUAL DISC GRINDERS* PART# 10 REVISED STARTING SERIAL # 011008 1 1 18 1 *NOTE: THIS KIT CAN BE USED TO UPGRADE ALL MODEL -EC OR -GC GRINDERS MANUFACTURED BETWEEN DEC. 1991 AND FEB. 00. SINCE FEB. 00 ALL PARTS ARE STANDARD ON THE GRINDERS. DEC. 00 ITEM #1 WAS CHANGED FROM A VAC PORT TO A /3 MULTI-VAC PORT. 19 18 ITEM# PART# DESCRIPTION QTY. 1 001 SKIRT GUARD 1 11 RUBBER SEAL -1/ x 1 3 13 RETAINING STRIP, RUBBER SEAL 1 11 BOLT, CARRIAGE 13 1/-0 X /8 GRADE 100 WASHER, FLAT 1/ SAE 13 1081 NUT, KEPS 1/-0 13 339 RETAINING BRKT., SKIRT CORNER 8 11 PANEL, VACUUM PORT " 1 9 1 RUBBER SEAL, REAR -1/ x 1 1 10 1 RETAINING STRIP, REAR SEAL 11 1080 SCREW, CAP /1-18 X 1 1 10801 WASHER, LOCK /1 13 1013 WASHER, FLAT /1 SAE 1 10113 SPACER, STL. 9/1ODx3/8IDx/3 1 030 PLUG, CAP 3" TUBE 1 1 83 BRACKET, MULTI-VAC PORT 1 1 108 SCREW, CAP STSHW 1/-0 X 1/ 18 10 CLAMP, HOSE, SAE #8, ADJ. TO -1/ 19 113 HOSE, FLEX "ID X 3"L 1 9 10 8 1 11 1 13 13 1 11 1 3 00 Page 1
E-MCKH-PL-00 MANUAL CHOKE KIT FOR HONDA GXV10. HP PART #1180 1 3 ITEM# PART# DESCRIPTION QTY. 1 1083 SCREW, CAP 1/-0 X 1/ 1 91301 DECAL, CHOKE /8 X /8 1 3 118 BRKT., CHOKE CONTROL 1 118 WASHER, BELLEVILE.00 X. X.018 1 1181 LEVER, CHOKE CONTROL 1 1010 NUT, HEX NYLON LOCK 1/-0 1 118 CAP, FLAT RED.0 X. X 1 1 00
E-MCK11H-PL-00 MANUAL CHOKE KIT FOR HONDA GXV30 11 HP PART #1190 9 3 8 1 ITEM# PART# DESCRIPTION QTY. 1 118 SCREW, MACHINE M X 1MM PHILLIP HD 1 ------- BREAKAWAY VIEW OF ENGINE THROTTLE - BRACKET (SHOWN FOR MOUNTING DETAIL) 3 100 WASHER, FLAT 1/ SAE 1 118 WASHER, FIBER. X. X.093 1 1183 LEVER, CHOKE CONTROL 1 118 WASHER, BELLEVILE.00 X. X.018 1 80 NUT, HEX NYLON LOCK M X 1MM 1 8 91301 DECAL, CHOKE /8 X /8 1 9 118 CAP, FLAT RED.0 X. X 1 1 00
FLOOR GRINDER STRIP-SERT ACCESSORY TUNGSTEN CARBIDE SCRAPER REVISED APRIL 00 3 1 E-STRIPSERT-PL-00 STARTUP PACKS #A10 PACK FOR 1-DISC GRINDER INCLUDES: (3) 100 ASSY. W/ PRO-TUNGSERT (3) 10 EXTRA PRO-TUNGSERT () 110 HARDWOOD WEDGE #A10 PACK FOR -DISC GRINDER INCLUDES: () 100 ASSY. W/ PRO-TUNGSERT (1) 10 PRO-TUNGSERT SIX-PACK (9) 110 HARDWOOD WEDGE 8 9 10 11 *QUANTITY REQUIRED 1-DISC GRINDER...3 -DISC GRINDER... -DISC GRINDER...1 ITEM# PART# DESCRIPTION QTY. 1 STRIP-SERT ASSEMBLY * 100 ASSY. WITH PRO TUNGSERT (ITEMS -9) 101 ASSY. W/O PRO TUNGSERT, ITEM 10 SCREW, SKT.HD.CAP 1/-13 X 3.,GR.8 1 3 10 TUNGSERT HLDR, STRIP-SERT(RED BOX) 1 113 SCREW, SKT. HD. CAP 1/-0 X 3/ 1 1188 WASHER, HI-COLLAR LOCK.ID X.33 1 10 PRO TUNGSERT, SIDED CARBIDE 1 or 10 PRO TUNGSERT (PACK OF INCLUDING: SIX OF ITEMS,, & AND ONE OF ITEM 11) 103 TUNGSERT BLOCK, STRIP-SERT 1 8 10 SPRING, COMP.. OD X 1. FL 1 9 101 NUT, HEX NYLON LOCK 1/-13 1 10 110 WEDGE CG, HARDWOOD (EA) 1 11 113 WRENCH, HEX L-KEY 3/1, SHORT-ARM 1 00 Page 10