SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 TÜV SÜD CERTIFICATION AND TESTING (CHINA) CO., LTD. 1 SHANGHAI BRANCH 3-13 F No. 151 Heng Tong Road Shanghai, 200 070, People's Republic of China Testing Location: No. 1999 Duhui Road Shanghai, 201 108, People's Republic of China Jian Qin Phone: +86 21 6148 7156 ELECTRICAL Valid To: April 30, 2018 Certificate Number: 3745.01 In recognition of the successful completion of the A2LA evaluation process (including an assessment of the laboratory s compliance with A2LA s EPA ENERGY STAR Accreditation Program 2 requirements), accreditation is granted to this laboratory at the location listed above, as well as the satellite laboratory location listed below, to perform the following ENERGY STAR, Safety, EMC, Automotive EMC, FCC, and Protocol testing: Test Technology: ENERGY STAR Testing 2 ENERGY EFFICIENCY Electrical and Photometric Measurements of Solid-State Lighting Products Measuring Luminous Flux and Color Maintenance of LED Packages, Arrays and Modules Projecting Long Term Lumen Maintenance of LED Light Sources ENERGY STAR Program Requirements Product Specification for Lamps (Light Bulbs) Eligibility Criteria Version 2.1 ENERGY STAR Program Requirements Product Specification for Luminaires (Light Fixtures) Eligibility Criteria Version 2.0 IES LM-79-08 IES LM-80-15 IES TM-21-11 Lamp Version 2.1 Luminaries Version 2.0 (A2LA Cert. No. 3745.01) Revised 02/07/2018 Page 1 of 13
ELECTRICAL SAFETY Testing Self-ballasted Lamps and Lamp Adapters UL 1993 Class 2 Power Units UL 1310 Power Units Other than Class 2 UL 1012 INMETRO ordinance for Quality Technical Regulation applicable to Luminaires for Public Road Illumination Safety of Household and Similar Electrical Appliances Part 1: General Requirements Safety of Household and Similar Electrical Appliances Part 2: Particular Requirements for Electric Irons Safety of Household and Similar Electrical Appliances Part 2: Particular Requirements for Shavers, Hair Clippers, and Similar Appliances Ordinance INMETRO No. 20 UL 60335-1 UL 60335-2-3 UL 60335-2-8 Electric heating appliances UL 499 Household Electric Personal Grooming Appliances UL 859 Motor Operated Household Food Preparing Machines Vacuum Cleaners, Blower Cleaners, and Household Floor Finishing Machines Electric Household Cooking and Food-serving Appliances UL 982 UL 1017 UL 1026 Insect-Control Equipment Electrocution Type UL 1559 Motor-operated Commercial Food-preparing Machines UL 763 Motor-operated Water Pumps UL 778 Movable and Wall or Ceiling-hung Electric Room Heaters UL 1278 Motor-operated Massage and Exercise Machines UL 1647 (A2LA Cert. No. 3745.01) Revised 02/07/2018 Page 2 of 13
ELECTRICAL SAFETY Testing (cont.) Audio, Video, and Similar Electronic Apparatus - Safety Requirements Information Technology Equipment - Safety Part 1: General Requirements Audio/video, information and communication technology equipment Part 1: Safety requirements Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory use Part 1: General Requirements Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory use Part 2-010: Particular Requirements for Laboratory Equipment for the Heating of Materials UL 60065; IEC 60065; EN 60065 UL 60950-1; IEC 60950-1; EN 60950-1 IEC 62368-1 EN 62368-1 UL 62368-1 UL 61010-1; IEC 61010-1; EN 61010-1 UL 61010-2-010 Electric Gardening Appliances UL 82 Stationary and Fixed Electric Tools UL 987 Electric Lawn Mowers UL 1447 Electric Chain Saws UL 1662 Part 1: General Requirements Part 2-1: Particular Requirements for Drills and Impact Drills Part 2-2: Particular Requirements for Screwdrivers and Impact Wrenches Part 2-3: Particular Requirements for Grinders, Polishers, and Disk-type Sanders Part 2-4: Particular Requirements for Sanders and Polishers other than Disk-type UL 60745-1 UL 60745-2-1 UL 60745-2-2 UL 60745-2-3 UL 60745-2-4 (A2LA Cert. No. 3745.01) Revised 02/07/2018 Page 3 of 13
ELECTRICAL SAFETY Testing (cont.) Part 2-5: Particular Requirements for Circular Saws Part 2-6: Particular Requirements for Hammers Part 2-8: Particular Requirements for Shears and Nibblers Part 2-11: Particular Requirements for Reciprocating Saws Part 2-13: Particular Requirements for Chain Saws Part 2-14: Particular Requirements for Planers Part 2-15: Particular Requirements for Hedge Trimmers Part 2-16: Particular Requirements for Tackers Part 2-17: Particular Requirements for Routers and Trimmers Part 2-19: Particular Requirements for Jointers Part 2-22: Particular Requirements for Cut-off Machines Part 2-23: Particular Requirements for Die Grinders and Small Rotary Tools UL 60745-2-5 UL 60745-2-6 UL 60745-2-8 UL 60745-2-11 UL 60745-2-13 UL 60745-2-14 UL 60745-2-15 UL 60745-2-16 UL 60745-2-17 UL 60745-2-19 UL 60745-2-22 UL 60745-2-23 (A2LA Cert. No. 3745.01) Revised 02/07/2018 Page 4 of 13
ELECTRICAL SAFETY Testing (cont.) Safety Part 1: General requirements Safety Part 2-2: Particular requirements for hand-held screwdrivers and impact wrenches Safety Part 2-4: Particular requirements for hand-held sanders and polishers other than disc type Safety Part 2-5: Particular requirements for hand-held circular saws Safety Part 2-11: Particular requirements for hand-held reciprocating saws Safety Part 2-14: Particular requirements for hand-held planers Safety Part 3-1: Particular requirements for transportable table saws - Safety - Part 3-4: Particular requirements for transportable bench grinders Safety Part 3-6: Particular requirements for transportable diamond drills with liquid System IEC 62841-1 EN 62841-1 UL 62841-1 UL 62841-2-2 UL 62841-2-4 UL 62841-2-5 UL 62841-2-11 UL 62841-2-14 UL 62841-3-1 IEC 62841-3-4 EN 62841-3-4 UL 62841-3-4 UL 62841-3-6 (A2LA Cert. No. 3745.01) Revised 02/07/2018 Page 5 of 13
ELECTRICAL SAFETY Testing (cont.) Safety Part 3-9: Particular requirements for transportable mitre saws Safety Part 3-10: Particular requirements for transportable cut-off machines UL 62841-3-9 UL 62841-3-10 1 Accreditation is granted to this laboratory at the location listed above as well as the satellite laboratory location listed below: No.16, Lane 1951 Duhui Road Shanghai, 201 108, People's Republic of China Jian Qin Phone: +86 21 6148 7156 Test Technology: Electromagnetic Compatibility Basic EMC Testing Electromagnetic compatibility (EMC) Part 6-1: Generic standards - Immunity for residential, commercial and light-industrial environments Electromagnetic compatibility (EMC) Part 6-2: Generic standards - Immunity for industrial environments Electromagnetic compatibility (EMC) Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial Environments Electromagnetic compatibility (EMC) Part 6-4: Generic standards - Emission standard for industrial environments Electrical equipment for measurement, control and laboratory use - EMC requirements Part 1: General requirements Electrical equipment for measurement, control and laboratory use - EMC requirements Part 2-2: Particular requirements - Test configurations, operational conditions and performance criteria for portable test, measuring and monitoring equipment used in low voltage distribution systems IEC 61000-6-1; EN 61000-6-1 IEC 61000-6-2; EN 61000-6-2 IEC 61000-6-3; EN 61000-6-3 IEC 61000-6-4; EN 61000-6-4 IEC 61326-1; EN 61326-1 IEC 61326-2-2; EN 61326-2-2 (A2LA Cert. No. 3745.01) Revised 02/07/2018 Page 6 of 13
Electromagnetic Compatibility (cont.) Basic EMC Testing (cont.) Industrial, scientific and medical equipment-radiofrequency disturbance characteristics - Limits and methods of measurement Vehicles, boats and internal combustion engines- Radio disturbance characteristics - Limits and methods of measurement for the protection of offboard receivers Electromagnetic compatibility Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission Electromagnetic compatibility Requirements for household appliances, electric tools and similar apparatus - Part 2: Immunity - Product family standard Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment Equipment for general lighting purposes EMC immunity requirements Information technology equipment Radio disturbance characteristics - Limits and methods of measurement Information technology equipment Immunity characteristics - Limits and methods of measurement Information technology equipment (ITE) - Limits and methods of measurement FCC Part 15, Unintentional Radiators FCC Part 15, Intentional Radiators below 26.5GHzexcept Part 15D and Part 15E (DFS) General requirements for compliance of radio apparatus License-exempt radio apparatus (all frequency bands): Category I equipment License-exempt radio apparatus: Category II equipment CISPR 11; EN 55011 CISPR 12; EN 55012 CISPR 14-1; EN 55014-1 CISPR 14-2; EN 55014-2 CISPR 15; EN 55015 IEC 61547; EN 61547 CISPR 22; EN 55022 CISPR 24; EN 55024 ICES-003 ANSI C63.4-2014 ANSI C63.10-2013; KDB Publication 789033 RSS-Gen RSS-210 RSS-310 (A2LA Cert. No. 3745.01) Revised 02/07/2018 Page 7 of 13
Electromagnetic Compatibility (cont.) Basic EMC Testing (cont.) Electromagnetic compatibility and Radio Spectrum Matters (ERM) - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements Electromagnetic compatibility and Radio Spectrum Matters (ERM) - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 khz and 246 GHz Electromagnetic compatibility and Radio Spectrum Matters (ERM) - ElectroMagnetic Compatibility (EMC) standard for radio equipment; Part 17: specific conditions for Broadband Data Transmission Systems EN 301489-1 EN 301489-3 EN 301489-17 Harmonic Current Emissions IEC 61000-3-2; EN 61000-3-2 Voltage Changes, Voltage Fluctuations and Flicker IEC 61000-3-3; EN 61000-3-3 Electrostatic Discharge (ESD) Immunity IEC 61000-4-2; EN 61000-4-2 Radiated, Radio-frequency, Electromagnetic Field Immunity IEC 61000-4-3; EN 61000-4-3 Electrical Fast Transient/Burst Immunity IEC 61000-4-4; EN 61000-4-4 Surge Immunity IEC 61000-4-5; EN 61000-4-5 Immunity to conducted disturbances, induced by radio-frequency fields IEC 61000-4-6; EN 61000-4-6 Power Frequency Magnetic Field Immunity IEC 61000-4-8; EN 61000-4-8 Voltage Dips, Short Interruptions and Voltage Variations IEC 61000-4-11; EN 61000-4-11 (A2LA Cert. No. 3745.01) Revised 02/07/2018 Page 8 of 13
Automotive EMC Testing Electrostatic Discharge (ESD) ISO 10605; TL 82466, TL 81000; ISO 13766; ISO 14982; EN 13309; GB/T 19951 Conducted Emissions CISPR 25; TL 965, TL 81000; EN 55025; GB/T 18655 Voltage Transient Emissions ISO 7637-2; TL 82066, TL 81000; EN 50498; GB/T 21437.2 Radiated Emissions CISPR 25; 2004/104/EC Annex VII (Broadband); 2004/104/EC Annex VIII (Narrowband); ECE Regulation 10 Annex 7 (Broadband); ECE Regulation 10 Annex 8 (Narrowband); ISO 13766 Annex D (Broadband); ISO 13766 Annex E (Narrowband); ISO 14982 Annex D (Broadband); ISO 14982 Annex E (Narrowband); EN 13309 Annex D (Broadband); EN 13309 Annex E (Narrowband); TL 965, TL 81000; EN 50498; EN 55025; GB/T 18655 Magnetic Fields Emissions B21 7110 (A2LA Cert. No. 3745.01) Revised 02/07/2018 Page 9 of 13
Automotive EMC Testing (cont.) Bulk Current Injection (BCI) ISO 11452-4; ECE Regulation 10 Annex 9; 2004/104/EC Annex IX; TL 82166, TL 81000; ISO 14982; EN 13309; GB/T 17619 Absorber-Lined Shielded Enclosure (ALSE) (up to 3200 MHz and 200V/m) ISO 11452-2; ECE Regulation 10 Annex 9; 2004/104/EC Annex IX; TL 82166, TL 81000; ISO 13766; ISO 14982; EN 13309; GB/T 17619 Electrical Load ISO 16750-2; GMW 3172; VW 80000 Magnetic Field Immunity ISO 11452-8; TL 82566; TL 81000 Conducted and Transient Immunity ISO 7637-2; ISO 7637-3; TL 82366; TL 82066; TL 81000; ISO 13766; ISO 14982; EN 13309; EN 50498; GB/T 21437.2; GB/T 21437.3 (A2LA Cert. No. 3745.01) Revised 02/07/2018 Page 10 of 13
Automotive EMC Testing RF Immunity to Hand Portable Transmitters ISO 11452-9; TL 81000; B21 7110 Protocol/Interoperability Communication networks and systems in substations - Part 6: Configuration description language for communication in electrical substations related to IEDs Communication networks and systems in substations - Part 7-1: Basic communication structure for substation and feeder equipment - Principles and models Communication networks and systems in substations - Part 7-2: Basic communication structure for substation and feeder equipment - Abstract communication service interface (ACSI) Communication networks and systems in substations - Part 7-3: Basic communication structure for substation and feeder equipment - Common data classes Communication networks and systems in substations - Part 7-4: Basic communication structure for substation and feeder equipment - Compatible logical node classes and data classes Communication networks and systems in substations - Part 8-1: Specific Communication Service Mapping (SCSM) - Mappings to MMS (ISO 9506-1 and ISO 9506-2) and to ISO/IEC 8802-3 Communication networks and systems in substations - Part 10: Conformance testing Communication networks and systems for power utility automation - Part 6: Configuration description language for communication in electrical substations related to IEDs Communication networks and systems for power utility automation - Part 7-1: Basic communication structure - Principles and models Communication networks and systems for power utility automation - Part 7-2: Basic information and communication structure - Abstract communication service interface (ACSI) IEC 61850-6, First Edition 2004-03 IEC 61850-7-1, First Edition 2003-07 IEC 61850-7-2, First Edition 2003-05 IEC 61850-7-3, First Edition 2003-05 IEC 61850-7-4, First Edition 2003-05 IEC 61850-8-1. First Edition 2004-05 IEC 61850-10, First Edition 2004-05 IEC 61850-6, Edition 2.0 2009-12 IEC 61850-7-1, Edition 2.0 2011-07 IEC 61850-7-2, Edition 2.0 2010-08 (A2LA Cert. No. 3745.01) Revised 02/07/2018 Page 11 of 13
Protocol/Interoperability (cont.) Communication networks and systems for power utility automation - Part 7-3: Basic communication structure - Common data classes Communication networks and systems for power utility automation - Part 7-4: Basic communication structure - Compatible logical node classes and data object classes Communication networks and systems for power utility automation - Part 8-1: Specific communication service mapping (SCSM) - Mappings to MMS (ISO 9506-1 and ISO 9506-2) and to ISO/IEC 8802-3 Communication networks and systems for power utility automation - Part 10: Conformance testing Conformance Test Procedures for Client System with IEC 61850-8-1 interface Conformance Test Procedures for Server Devices with IEC 61850-8-1 interface Conformance Test Procedures for Client System with IEC 61850-8-1 Edition 2 interface Conformance Test Procedures for Server Devices with IEC 61850-8-1 Edition 2 interface IEC 61850-7-3, Edition 2.0 2010-12 IEC 61850-7-4, Edition 2.0 2010-03 IEC 61850-8-1, Edition 2.0 2011-06 IEC 61850-10, Edition 2.0 2012-12 30900601-Consulting (UCA) 539-MOC/INC (UCA) 74103102-OPE/INC (UCA) 74100432-MOC/INC (UCA) 2 A2LA provides accreditation to the U.S. EPA s Conditions and Criteria for Recognition of Laboratories for the ENERGY STAR Program by verifying an organization s compliance to the related test methods listed above. Accreditation by A2LA does not infer Recognition by the EPA for ENERGY STAR testing. Please verify this organization s recognition status by using the EPA s searchable database, located at http://www.energystar.gov/index.cfm?fuseaction=recognized_bodies_list.show_rcb_search_form On the following types of products: Household Appliances, Tools; Lighting; Electrical Equipment for Measurement, Control and Laboratory Use, Industrial, Scientific and Medical Equipment (ISM), Information Technology Equipment (ITE); Vehicles, Boats, and Internal Combustion Engines; Radio equipment; Intentional and Unintentional Radiators; Construction Machinery; Automotive Components. Protocol testing: Power System Automation Devices and Systems. (A2LA Cert. No. 3745.01) Revised 02/07/2018 Page 12 of 13
Testing Activities Performed in Support of FCC Declaration of Conformity and Certification in Accordance with 47 Code of Federal Regulations and FCC KDB 974614, Appendix A, Table A.1 3 : Rule Subpart/Technology Test Method Maximum Frequency Unintentional Radiators Part 15B ANSI C63.4:2014 18 GHz Intentional Radiators Part 15C ANSI C63.10:2013 26.5 GHz U-NII without DFS Intentional Radiators Part 15E ANSI C63.10:2013 26.5 GHz UWB Intentional Radiators Part 15F ANSI C63.10:2013 26.5 GHz BPL Intentional Radiators Part 15G ANSI C63.10:2013 26.5 GHz White Space Device Intentional Radiators Part 15H ANSI C63.10:2013 26.5 GHz 3 Accreditation does not imply acceptance to the FCC equipment authorization program. Please see the FCC website (https://apps.fcc.gov/oetcf/eas/) for a listing of FCC approved laboratories. (A2LA Cert. No. 3745.01) Revised 02/07/2018 Page 13 of 13
Accredited Laboratory A2LA has accredited TÜV SÜD CERTIFICATION AND TESTING (CHINA) CO., LTD. SHANGHAI BRANCH Shanghai, People's Republic of China for technical competence in the field of Electrical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This laboratory also meets the A2LA R222 - Specific Requirements - EPA ENERGY STAR Accreditation Program. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 24 th day of September 2015. President and CEO For the Accreditation Council Certificate Number 3745.01 Valid to April 30, 2018 Revised February 7, 2018 For the tests to which this accreditation applies, please refer to the laboratory s Electrical Scope of Accreditation.