Daikin Altherma high temperature remote controller guide for schedule timers and operation functions 13 14 15 16 17 1 12 2 11 10 9 3 4 8 7 6 5 1. Space heating on/off 2. Target flow water temperature / room temperature set point once button 5 has been pushed 3. N/A 4. Domestic hot water on/off 5. Room temperature set point 6. Flow water set point 7. Time adjust 8. Schedule timer on/off 9. Weather dependant (compensation) on/off 10. Outdoor unit quiet operation 11. Programming button for schedule timer 12. Schedule timer action 13. Day display 14. Time display 15. Space heating operation mode 16. Domestic hot water operation active 17. Outdoor quiet operation active
Setting the clock Push and hold until the clock starts to flash. Adjust the time via Adjust the day via To save adjustments push Setting the schedule timer Note: if a remote room programmable thermostat is being used will be displayed in the top right of the display. This means the on/off of the equipment is controlled by the remote room programmable thermostat. There are two types of schedule timers 1) 7 day timer with 5 actions per day, for space heating and domestic hot water 2) 24 hour timer with 5 actions, only for outdoor unit quiet operation Hint: When programming the schedule timers use the menu, press to go back a step in the menu. to advance through the To enter the schedule timer function press Once into the first schedule timer menu use the to select the desired program. 1) Space heating 2) Domestic hot water 3) Outdoor quiet function To enter any of the schedule timers press once. 01 Daikin Altherma high temperature remote controller guide
Setting the schedule timer (continued) 1) 7 Day schedule timer The selected program will be flashing (either the or symbol and also the days of the week). Use the To enter the chosen day push now appear). to adjust the day of the week. (if this is done on space heating this screen will If the schedule timer has been previously programmed then you can view each schedule by using. To alter or add a schedule push and hold down until the clock symbol begins to flash. It is now possible to program the schedule timer. When programming for the first time it will be necessary to push the action 1 next to the clock. once to display These buttons will change the time of the action set. These buttons will change the water flow temperature (should be N/A). These buttons will change the room set point (desired room temperature) as long as no third party room thermostat is fitted. 02 Daikin Altherma high temperature remote controller guide
This button will change the desired function of the schedule timer from a set water flow temperature to weather dependant mode and finally to switching the unit off (please see note). Push to advance to the next schedule action number. Repeat previous step until either you don t require any further actions or a maximum of 5 actions have been selected. Push and hold until settings flashes up on the controller and the subsequent day is flashing (if saving Monday, Tuesday will now be flashing). Repeat steps until everything is programmed, or copy the days as follows. Copying days If you require to copy the day you have just programmed then push once and it will take you back one step in the menu. This will allow you to select the day you had previous programmed by pressing once. You can now copy that day across to the next day by pressing and holding and until setting flashes up on the controller and the subsequent day is now shown. To continue copying then repeat pressing and holding and as before, until you have programmed the week or until the day you wish to schedule the timer. Please remember to use if required. button to go back one step or until main screen 2) 24 hour schedule timer Once you have entered the night quiet mode, will be displayed. This schedule only has 5 actions (repeats every 24 hours) which can be viewed by pushing the (if previously programmed). To adjust the schedule timer push and hold until the clock symbol begins to flash. When programming for the first time it will be necessary to push once to display action 1 next to the clock. 03
These buttons will change the time of the action set. This button will change the desired function of the schedule timer from on to off. Push to advance to the next schedule action number, repeat previous step until either you don t require any further actions or a maximum of 5 actions have been selected. Push and hold until settings flashes up on the controller. Please remember to use if required. button to go back a menu, until back to main screen Note: If turning the space heating off in the schedule timer it may prevent the unit from switching back on by the schedule timer. This is not a fault, the schedule timer has to be adjusted so the unit never has an off function. Just change the desired room temperature set point i.e. 16 C; or even reduce the water flow temperature down to 25 C to make sure the unit is only required to maintain a background temperature. This will allow you to switch off the space heating schedule timer in the summer months by switching to off, allowing the domestic hot water schedule timer to carry on operating as before. Once all the schedule timers have been programmed use normal remote controller screen. until you are back to the Activating the schedule timer To activate the schedule timer push and the clock will be displayed on the left hand side of the controller. Push it again and the clock symbol will disappear from the controller deactivating the schedule timer. 04
Additional information Last command If there is no external room programmable thermostat, the controller works on last command basis i.e. if you change the water flow temperature or desired room temperature, then this will stay the same until it is either changed or there is an action programmed in the schedule timer such as water temperature change or off function. Domestic hot water mode It is possible to boost the domestic hot water if a shortage occurs. This setting will override any current setting at the time of operation. To activate the domestic hot water boost mode press and hold until the symbol starts flashing. This setting will deactivate once the domestic hot water has reached its set point. www.altherma.co.uk For full user instructions, please refer to the Daikin Altherma operation manual. Daikin Airconditioning UK Ltd The Heights, Brooklands, Weybridge, Surrey KT13 0NY Tel 0845 6419000 Fax 0845 6419009 FSC DesignHQ. Copyright 2010 Daikin. 05.10 / Printed in the UK on FSC certified paper from sustainable sources.