FEDERAL SIGNAL CORPORATION Mounting Kits Models LWMB2 and LCMB2 CUSTOM MOUNTING BRACKETS Heavy-duty construction Easy installation For walls and outside corners Indoor and outdoor use Replaces unsightly and hazardous makeshift supports 1 /2-inch, 3 /4-inch and 1-inch pipe mount Type 3R Federal Signal s Models LWMB2 and LCMB2 mounting brackets are specifically designed for use with Federal Signal s stationary warning lights to provide an easy and consistent means of mounting lights throughout a facility. Federal Signal s Models LWMB2 and LCMB2 are constructed of durable cast aluminum and sealed with gray powder coat paint. Easy to install, these units can be wired through the back of the bracket for electrical box mounting or through the threaded hole in the base for external 1 /2-inch conduit connection. Each kit includes a bracket, plate and mounting screws. Easy installation, heavy-duty construction and a professional appearance make the brackets suitable for use in commercial, institution and industrial environments. These brackets are suitable for any Type 3R application in ordinary (non Division 1/Division 2) environments. The LCMB2 and LWMB2 mounting kits may be used with the following Federal Signal models: 121S, 131ST, 131DST, 131C, 141(120V), 141ST, 225, 371, 371L, 371ST, 371DST, AV1, AV1ST, FB2PST and the FB24ST. Net Shipping Model Height Width Extension Weight Weight LWMB2 6" 6 3 /8" 5 7 /8" 2.6 lbs. 2.95 lbs. LCMB2 6" 5" 5 3 /4 2.3 lbs. 2.5 lbs.
MOUNTING KITS (LWMB2, LCMB2) Installation of a wall bracket on a 4" electrical box PLASTER RING OR ELECTRICAL BOX ADAPTER PLATE MOUNTING BRACKET ASSEMBLY Installation of a wall bracket with conduit wiring ANCHORS (NOT SUPPLIED) WALL MACH. SCREWS SET SCREWS WALL MOUNTING BRACKET MACH. SCREWS.028 HOLE SIZE SHEET METAL SCREWS BACKPLATE 1/2" TAPPED HOLE CONNECTOR 1/2" CONDUIT Installation of an outside corner bracket with conduit WALLS ANCHORS (NOT SUPPLIED) BACKPLATE.028 HOLE SIZE MACH. SCREWS SET SCREWS 1/2" TAPPED HOLE CORNER MOUNTING BRACKET CONNECTOR 1/2" CONDUIT HOW TO ORDER Specify model LCMB2 Corner Mount LWMB2 Wall Mount Please refer to Model Number Index LCMB2/LWMB2 beginning on page 377 2645 Federal Signal Dr., University Park, IL 60466 Tel: 708.534.4756 Fax: 708.534.4852 www.federalsignal-indust.com 109
FEDERAL SIGNAL CORPORATION Synchronous Strobe Module Model SSM SYNCHRONIZE LOW IN-RUSH FEDERAL SIGNAL STROBES Synchronizes strobe lights to 72 flashes per minute Mounts on double-gang electrical box UL1971 Approved for hearing impaired applications Polarized design allows for remote supervision Compatible with select Federal Signal model strobe lights (see chart) The Model SSM, Synchronous Strobe Module, is an electronic timing mechanism designed to energize select Federal Signal low in-rush 24VDC strobe lights simultaneously, while maintaining the ability to remotely supervise the strobe light circuit. This module is designed to synchronize a special series of Federal Signal strobe lights, which meet the requirement for Private-Mode Fire Alarm use, while maintaining the agency approval and environmental rating of the strobe light. The SSM is only compatible with Federal Signal brand strobe lights. See compatible models on the How to Order page. The SSM enables the customer to meet local building codes through a visually appealing single-flash created by the simultaneous control of strobe lights connected to it. Mixed signals are reduced to a minimum as reflection of many light pulses are now viewed as one single flash. The SSM mounts to the plaster ring of a double-gang electrical box, and requires 24 VDC at all times to operate the timing circuit. Screw terminals are provided for field termination of control wiring and a maximum of three non-explosion-proof strobe lights or two Explosion-proof strobe lights may be connected to each SSM. Electrically, the SSM should be mounted in the middle of the circuit, with a maximum cable distance of 100 from the SSM to each Strobe light. Supervision is accomplished the same as without the SSM, with a flash rate of 72 Flashes per minute in lieu of the advertised flash rate for each strobe light. The SSM is capable of switching 6 Amps of current. Please note: Not all strobe lights have the same in-rush current and therefore the SSM s circuit s switching potential may be reduced. Please see the application drawings on the second page. Operating Model Current Voltage SSM 0.95 amps 24VDC
VISUAL SYNCHRONOUS STROBE MODULE (SSM) FB24STHI 224XSTHI STROBE #1 FB24STHI 224XSTHI STROBE #2 FB24STHI 224XSTHI STROBE #3 STROBE SIGNAL 24VDC IN 24VDC OUT CONTROL PANEL POWER SUPPLY SYNC MODULE SSM RED BLACK RED BLACK RED BLACK IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT END OF LINE RESISTOR 290A5130 FSEX HI STROBE #1 FSEX HI STROBE #2 CONTROL PANEL POWER SUPPLY STROBE SIGNAL 24VDC IN OUT IN IN IN OUT IN 24VDC OUT SYNC MODULE SSM RED BLACK RED BLACK OUT OUT END OF LINE RESISTOR SPECIFICATIONS Operating Temperature: 32 F to 120 F 0 C to 49 C Net Weight: 0.53 lbs. 0.24 kg Ship. Weight: 0.93 lbs. 0.42 kg Height: 4.5 114.3 mm Width: 4.5 114.3 mm Depth: 1.12 28.4 mm HOW TO ORDER Specify model COMPATIBLE STROBE LIGHTS 224XST-024, Series C 225XST-I-024, Series B FB2PSTX-I-024, Series B FB2PST-I-024, Series B FB24ST-024, Series B FB24ST-HI-024, Series C 224XST-HI-024, Series B FSEX-HI-024, Series D FSEX-024, Series D 27XST-024, Series E REPLACEMENT PARTS Description PC Board Assembly 2 per circuit 2 per circuit 2 per circuit Part Number K2001933A 2645 Federal Signal Dr., University Park, IL 60466 Tel: 708.534.4756 Fax: 708.534.4852 www.federalsignal-indust.com
FEDERAL SIGNAL CORPORATION Push Button Stations Model PS Series FOR VANDAL-RESISTANT ACTIVATION OF EMERGENCY SYSTEMS "Fire", "Evacuation", and "Emergency" stations available Quick reset Cover with alarm discourages tampering UL and cul Listed, CSFM Approved ADA Compliant Type 3R with cover and gasket These multi-purpose, initiating devices cover a wide range of industrial and commercial applications. The Federal Signal pushbutton stations function like a traditional fire alarm pull station, providing a simple contact closure to activate emergency equipment, audible and visual signals and alarm panels. The push button stations are available in two colors Red or Yellow. The red Emergency and yellow "Evacuation" units have a Push and Turn reset button. The red Fire unit has a Push and Key Lock reset button. Each unit is available with or without a tamper-resistant polycarbonate cover. Covered units work to protect against physical damage to the station and to prevent false alarms without restricting use in emergency situations. When the cover is lifted to gain access to the alarm, a piercing tone sounds, calling immediate attention to the area. The piezo horn is quiet once the cover is closed. Power to the piezo alarm is provided by a 9VDC battery (included). The sounder cover mounts easily over the station with four anchor screws. The terminal block provides easy installation and maintenance. Units mount on existing single-gang electrical boxes or 4" x 4" electrical boxes with plaster ring adapters (customer supplied). Units are UL and cul Listed, meeting Type 3R specifications for outdoor use with the cover and gasket. They are also ADA Compliant (requiring less than five foot pounds for activation). Contact ratings for the Push Button Stations are 600VAC @ 3 amps and 250VDC @ 1 amp. MODEL DESCRIPTION PUSH BUTTON STATION (Shown At Top) PSFI-R Red Station with Push & Key Reset Button FIRE PSEV-Y Yellow Station with Push & Turn Reset Button EVACUATION PSEM-R Red Station with Push & Turn Reset Button EMERGENCY PUSH BUTTON STATION WITH SOUNDER COVER (Shown At Bottom) PSFISC-R Red Station with Push & Key Reset Button & Sounder Cover FIRE PSEVSC-Y Yellow Station with Push & Turn Reset Button & Sounder Cover EVACUATION PSEMSC-R Red Station with Push & Turn Reset Button & Sounder Cover EMERGENCY Note: Other colors and text available upon request.
PUSH BUTTON STATIONS (PS SERIES) Push button activation twist and pull to reset Key lock mechanism is used to reset after activation Optional cover (shown in photo) protects against vandalism by sounding a low db localized alarm when cover is lifted. SPECIFICATIONS Net Weight: 3.3 lbs. 1.5 kg Shipping Weight: 4.2 lbs. 5.94 kg Depth without Cover: 2.0" 50.8mm with Cover: 2.4" 61mm Width without Cover: 3.25" 82.6mm with Cover: 5.5" 139.7mm Height without Cover: 4.9" 124.5mm with Cover: 8.4" 213.4mm HOW TO ORDER Specify model number Please refer to Model Number Index PS beginning on page 382 ACCESSORIES Description Cover Only, Fire, Red Cover Only, Evacuation, Yellow Cover Only, Emergency, Red Contact, normally open Contact, normally closed Part Number PSCF-R PSCE-Y PSCE-R K229277A K229277A-01 2645 Federal Signal Dr., University Park, IL 60466 Tel: 708.534.4756 Fax: 708.534.4852 www.federalsignal-indust.com 321
FEDERAL SIGNAL CORPORATION Uninterruptible Power Systems Model PSU Series A UPS FOR EVERY INDUSTRIAL APPLICATION Provides steady regulated voltage to /-3% 100% power conditioning Seamless switching to battery back up Output voltage 120/240VAC Available in 120VAC, 208VAC and 240VAC Floor standing or optional rack mount Available with 30 or 60 minute battery Federal Signal Uninterruptible Power Systems provide a clean and constant, regulated power supply in harsh electrical environments where the available power is polluted, fluctuating or unreliable. The Model PSU is available in a range of kva outputs from 1.0 to 7.5 with a choice of battery life of thirty or sixty minutes. Output voltage is 120/240VAC with a choice of operating voltages from 120VAC, 208VAC and 240VAC. Each Federal Signal Uninterruptible Power System provides steady, regulated voltage to /- 3% and features and input power factor correction with less than 10% total harmonic distortion. Double magnetic conversion prevents damaging load-generated harmonics from backing up into the utility lines. System status is communicated via LED indicators and an LCD display, including input voltage, output voltage, percent of battery capacity, percent of load, percent of battery charged, system on, system on battery, low battery warning and alarm. The Federal Signal Uninterruptible Power Systems are designed to support such applications as networking, hosts/hubs, voice mail, telecommunications, industrial controls, SCADA systems, personal computers, communication closets and distributed control system. Battery Model kva Time Input Voltage Style PSU10 1.0 30 or 60 min. 120, 208 or 240VAC Floor standing or rack PSU14 1.4 30 or 60 min. 120, 208 or 240VAC Floor standing or rack PSU18 1.8 30 or 60 min. 120, 208 or 240VAC Floor standing or rack PSU21 2.1 30 or 60 min. 120, 208 or 240VAC Floor standing or rack PSU35 3.5 30 or 60 min. 120, 208 or 240VAC Floor standing or rack PSU50 5.0 30 or 60 min. 120, 208 or 240VAC Floor standing or rack PSU75 7.5 30 or 60 min. 120, 208 or 240VAC Floor standing or rack
UNINTERRUPTIBLE POWER SYSTEMS (PSU) 2 3 4 1 6 7 8 9 5 10 11 Note: Dimensions and weight vary by kva and battery life requirements. Call factory for complete specifications FEATURES 1 Input Volts - Indicates the input voltage. 2 Output Volts - Indicates the output voltage. 3 Percent Load - Indicates the unit is monitoring the output load capacity relative to maximum watts. 4 Percent Battery - Indicates unit is monitoring the battery charger when UPS is on utility power. 5 Display Select - Selects one of four monitor funcitons mentioned above. The display monitors one function at a time and is selected by the "Display Select" button. 6 System On - Indicates the correct AC input voltage is present. 7 System On Battery - Indicates the UPS is on battery power accompanied by an audible alarm. The UPS may switch to battery power even when it appears there are not power outages when the UPS detects input sages and surges. 8 Low Battery - Indicates batteries are low and a total UPS shutdown is immanent. This alarm set point is user selectable from 10% - 90% of battery remaining. 9 Alarm - LED On is accompanied by an audible alarm. Alarm will clear once the condition is resolved. 10 Battery Circuit Breaker 11 AC Circuit Breaker SPECIFICATIONS Input: 120, 208 or 240VAC at 60Hz Operating Range: 10%, -40% Frequency: ± 2.5Hz Power Factor: Self Correcting to >0.95 Input Harmonics: <10% THD Spike Attenuation: 3000:1 Overload Capability: 125% for ten minutes Surge Capability: 150% of rated output HOW TO ORDER Specify operating voltage Specify kva requirement Specify battery Specify floor standing or rack mount Please refer to Model Number Index PSU beginning on page 379 2645 Federal Signal Dr., University Park, IL 60466 Tel: 708.534.4756 Fax: 708.534.4852 www.federalsignal-indust.com 207