User s Manual and Operating Instructions Model Numbers: CL-30P-DDF, CL-20F-DDF, CL-24O-DDF, CL-30-DDF READ AND SAVE THESE INSTRUCTIONS IMPORTANT: Read and understand all of the directions in this manual before assembling, starting, or servicing the fan. Improper use of this fan can cause serious injury. Keep this manual for future reference. For ventilating use only. Do not use to exhaust hazardous chemicals or use near any flammable liquids or gases as sparks from motor may ignite fumes. Never use the fan in spaces which contain products such as gasoline, solvents, paint thinners, dust particles, volatile or airborne combustibles, or any unknown chemicals. This product meets and exceeds the requirements of OSHA 1910.212(a)(5), the standard which regulates electric fan blade safety, and is certified under UL# E234000, established and made effective April 10, 2003, and updated March 23, 2005, by Underwriters Laboratories, Inc. Please note the serial number of your fan, and write it on the back of this User s Manual for future reference. Distributed by: TRACTOR SUPPLY COMPANY 200 POWELL PLACE BRENTWOOD, TN 37027 For customer support, call: 1-866-641-4540 950450280-12
Safety Information... 2 20 Floor Fan... 3 24 Barrel Fan... 4-5 30 Pedestal Fan... 6-7 DO NOT MOVE FAN WHILE OPERATING! MOVING FAN DURING OPERATING CAN CAUSE BLADE DAMAGE. - Turn off, unplug unit, and wait for fan to stop before moving, storing, and / or changing operating locations. Table of Contents Safety Information 30 Drum Fan... 8-10 Troubleshooting... 11 Warranty... Back Cover IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY, SERVICE OR USE OF THIS FAN. FAILURE TO COMPLY WITH THESE INSTRUCTIONS COULD RESULT IN SERIOUS PERSONAL INJURY AND / OR PROPERTY DAMAGE. If safety guards have been removed to service or maintain this fan, reinstall or remount the safety guards as previously installed. This unit is designed for indoor use only. Do not expose to elements or allow to become wet. To guard against electric shock while operating, do not allow fan to come in contact with other grounded objects such as pipes, radiators, etc. Risk of fire, electric shock, or personal injury when performing service or maintenance. Unplug or disconnect the fan from the power supply before servicing. To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any Solid- State Speed Control Device. To Reduce The Risk Of Electric Shock And Injury To Persons, Do Not Use In a Window. For General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive Materials And Vapors. - Operate only on 115 volt 60 Hz (cycle) current with a minimum of a 15 amp circuit. - Before operating always check fan for loose or damaged parts. Inspect power cord for any damage. Never use fan if any parts are damaged or missing. Never use fan without safety guards attached. - When used with an extension cord, use only cord of proper size (Amp rating), UL listed, and with receptacle to accept three prong grounded plug furnished on the fan s power cord. Always keep power cord and extension cords away from heat, oil, and sharp edges. Inspect cords periodically and replace if damaged. - Disconnect fan from power source when not in use, before servicing and when cleaning or repairing. - Repair of this appliance should be done by a qualified electrician. - In case of power failure, turn fan off at knob or power chain to prevent unexpected restarting and component damage. - Keep children away from fan at all times. 2 www.tractorsupply.com For customer support, call 1-866-641-4540 HVF Air Circulator User s Manual
Installation and Assembly If the Wall Mount Kit is applied, the installer MUST be certain that the support bracket is mounted to a minimum of a 2x4 stud, and that it is able to support 50 pounds continuously. 1. Remove 1 screw from each Frame Support L and R (Items 7 and 19). Exploded View 20 FLOOR FAN (requires Phillips head screwdriver) 2. Slide Frame Support L and Frame Support R into Support Frame (Item 21) and line up holes for screw. 3. Re-attach screw to Frame Support L and Frame Support R. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 15 23 24 22 21 20 19 18 17 Figure 1: Exploded View of CL-20F-DDF Replacement Parts Item # Description Part Number 1 Logo Plate 95-043-0365 2 Front Grille 95-032-0160 3, 4, 5 Fan Blade Assembly 95-003-0615 6 Frame Washer 95-024-0250 7 Frame-Support L 95-024-0265 8 Main Circle Tube 95-024-0280 9 Top Washer 95-024-0290 10 Rear Grille 95-032-0260 11 Motor 95-030-0525 12 Switch Holder 95-031-0310 13 Switch 95-031-0120 Item # Description Part Number 14 Switch Cover 95-031-0510 15 Cord Bushing 95-026-0165 16 Control Knob 95-027-0110 17 Front Foot 95-023-0220 18 Rear Foot 95-023-0230 19 Frame-Support R 95-024-0275 20 Swivel Spacer 95-050-0180 21 Lower Support Frame 95-024-0245 22 Power Cord 95-026-0240 23 Capacitor 95-004-0225 24 Wall Mount Kit 95-078-0100 HVF Air Circulator User s Manual For customer support, call 1-866-641-4540 www.tractorsupply.com 3
24 BARREL FAN Installation and Assembly - Floor 1. Locate fan in safe, desired position on level ground, and connect to approved power source. Exploded View 1 2 3 4 5 6 7 8 9 10 11 12 15 13 14 16 19 17 18 20 Figure 2: Exploded View of CL-24O-DDF 30 Replacement Parts Item # Description Part Number 1 Front Grille 95-043-0415 2 Fan Barrel 95-001-0400 3 Power Knob 95-027-0130 4 Power Knob Holder 95-031-0325 5 Capacitor 95-004-0235 6 Power Cord 95-026-0255 7 Motor 95-030-0535 8 Motor Mount Assembly 95-030-0555 9 Motor Cooling Fan 95-030-0556 10 Fan Blade Assembly 95-003-0625 11 Rear Grille 95-032-0275 12 Front Leg 95-009-0600 13 Horizontal Adj. Knob 95-015-0150 14 Spacer 95-050-0200 15 Outer Ring Frame 95-024-0320 29 28 27 26 25 22 23 24 Item # Description Part Number 16 Vertical Adj. Knob 95-015-0150 17 Wall Mount 95-078-0200 18 Handle Pad 95-007-0100 19 Spacer 95-050-0200 20 Handle Arm 95-006-0300 21 Rear Leg 95-009-0610 22 Large Base Cap 95-024-0410 23 Large Base 95-024-0400 24 Foot Pad 95-023-0240 25 Wall Bracket - L 95-077-0100 26 Wall Bracket - R 95-077-0110 27 Small Base 95-024-0500 28 Small Base Cap 95-024-0500 29 Wheel 95-024-0510 30 Lower Mount 95-024-0325 21 4 www.tractorsupply.com For customer support, call 1-866-641-4540 HVF Air Circulator User s Manual
24 BARREL FAN Installation and Assembly - Wall Mount If the Wall Mount Kit is applied, the installer MUST be certain that the Wall Mount is mounted to a minimum of a 2x4 stud, and that it is able to support 50 pounds continuously. (requires flat head screwdriver) 1. Attach Wall Mount (item 17 on page 4) to wood stud as shown below. 2. Slide Wall Bracket L and Wall Bracket R on Large Base (item 23) onto Wall Mount. Wall Mount (item 17) Wall Handle Arm (item 20) Wall Large Base (item 23) Wall Mount (item 17) Figure 3: Wall Mount installation HVF Air Circulator User s Manual For customer support, call 1-866-641-4540 www.tractorsupply.com 5
Installation and Assembly REQUIRED TOOLS: Pliers Knife Phillips head screwdriver Flat head screwdriver 10mm / adjustable wrench 6mm hex wrench (included) PARTS INCLUDED IN BOX: Rubber Base Ring Base Front Grille Rear Grille Motor Assembly Fan Blade Assembly Spring Support Pole Assembly 1. Attach Rubber Base Ring (item 16 on page 7) to outer edge of Base (item 15). Be sure ribbed side of Base Ring is facing down. 2. Remove 5 screws from Flange on bottom of Lower Support Pole (item 16). 3. Completely extend Upper Support Pole (item 21) from Lower Support Pole and insert Spring into bottom of Lower Support Pole. 4. Attach Support Pole Assembly to Base. Tighten hardware using star parttern to insure a tight, uniform fit. 5. Stand assembly on Base, and press down Upper Support Pole and then tighten Height Adjustment Knob (item 3). 6. Attach Motor Support Assembly to Motor Assembly (see figure 5). 7. Place Motor Support into Upper Support Pole. - Insert Pivot Bolt and tighten. 30 PEDESTAL FAN - Insert Tilt Adjustment Knob and tighten. 8. Remove 4 screws on motor, and attach the Rear Grille. Tighten screws only after all 4 screws are reattached to the motor. 9. Remove the screws on the Motor and attach the Rear Grille onto groove in motor shaft, and replace screws (See figure 4). 10. Loosen the set screw on the back of the Fan Blade Assembly and slide onto the motor shaft. Do NOT slide fan blade screw CAUTION beyond the groove on the shaft! This will cause the fan blade to not spin properly and can cause damage to your fan! Be sure that fan shaft is flush with front of fan blade assembly. 11. Position set screw over flat groove on motor shaft and tighten set screw using 6mm hex wrench (included). Be sure set screw is on the groove, and the front of Fan Blade Assembly is flush with front of shaft before tightening. 12. Attach Front Grille by first aligning the top hooks of the Front Grille onto the top of the Rear Grille edge. Work your way around the grille, placing the Front Grille hooks over the Rear Grille edge. If necessary, use a flat head screwdriver to help pry the Front Grille hooks over the Rear Grille edge. Continue until all hooks are completely attached to the Rear Grille edge. Machine Screw Motor Assembly Rear Grille Pivot Bolt Motor Support Assembly Wing Nut Motor Tilt Adjustment Knob Nut Upper Support Pole Figure 4: Attaching Rear Grille to Motor Figure 5: Attaching Motor to Motor Support Assembly 6 www.tractorsupply.com For customer support, call 1-866-641-4540 HVF Air Circulator User s Manual
Exploded View 30 PEDESTAL FAN 4 5 6 9 8 23 2 7 1 22 10 11 3 12 13 17 19 Figure 6: Exploded View of CL-30P-DDF Replacement Parts 15 16 14 Item # Description Part Number 1 Logo Plate 95-043-0360 2 Front Grille 95-032-0180 3 Height Adjustment Knob 95-015-0205 4, 5, 6 Fan Blade Assembly 95-003-0630 7 Power Switch (Chain) 95-031-0140 8 Motor Assembly 95-030-0545 9 Rear Grille 95-032-0280 10 Height Adjust. Knob Nut 95-015-0215 11 Pipe Ring 95-017-0215 12 Pipe Support 95-017-0220 13 Lower Support Pole 95-017-0205 18 21 20 Item # Description Part Number 14 Latch Spring 95-060-0210 15 Upper Base 95-024-0225 16 Lower Base (Rubber Base Ring) 95-024-0235 17 Motor Support 95-030-0560 18 Left Support 95-030-0570 19 Right Support 95-030-0575 20 Tilt Adjustment Knob 95-015-0210 21 Upper Support Pole 95-010-0305 22 Power Cord 95-026-0260 23 Capacitor 95-004-0240 HVF Air Circulator User s Manual For customer support, call 1-866-641-4540 www.tractorsupply.com 7
30 FLOOR FAN -OPTIONAL CEILING MOUNT Exploded View 8 9 10 11 16 17 18 26 20 12 19 22 23 24 1 26 2 3 4 Figure 7: Exploded View of CL-30-DDF Replacement Parts 5 6 7 Item# Description Part Number 1 Front Guard 95-032-0140 2 Front Swivel Bracket 95-050-0100 3 Fan Blade Assy 95-003-0505 4 Fan Holder 95-003-0150 5 Motor 95-030-0500 6 Frame Foot 95-023-0200 7 Cart Frame 95-009-0400 8 Swivel Cover 95-050-0106 9 Frame Swivel Bracket 95-050-0111 10 Frame Upper Swivel Latch 95-050-0120 11 Swivel Latch Pin 95-050-0131 12 Frame Cap 95-011-0300 13 Wheel 95-008-0160 13 14 15 21 25 Item# Description Part Number 14 Wheel Axle 95-008-0260 15 Wheel Frame 95-008-0500 16 Upper Swivel Housing 95-050-0141 17 Frame Lower Swivel Latch 95-050-0150 18 Latch Spring 95-060-0155 19 Lower Swivel Housing 95-050-0161 20 Rear Guard 95-032-0240 21 Rear Swivel Bracket 95-050-0170 22 Capacitor 95-004-0200 23 Power Switch 95-025-0500 24 Rear Motor Cover 95-048-0100 25 Power Cord 95-026-0150 26 Guard Latch Assembly 95-033-0220 8 www.tractorsupply.com For customer support, call 1-866-641-4540 HVF Air Circulator User s Manual
30 FLOOR FAN -OPTIONAL CEILING MOUNT Floor Installation Simply locate fan in safe, desired position on level ground, and connect to approved power source. NOTE: This fan uses a folding wheel design. For quick assembly, simply swing the wheels out and snap to lock in place. Ceiling Mount Installation The installer MUST be certain that the ceiling that the mounting bracket is mounted to is able to support 100 pounds continuously. MOUNTING BRACKET INSTALLATION: 1. Remove Wheel Frame (item 15 on page 8). 2. Attach Cart Frame to Ceiling beam using U-bolts (item 5 on page 10). 3. Assemble and attach Ceiling Mount Assembly as shown in figure 10 on page 10. SAFETY CABLE INSTALLATION: 1. After the fan is securely mounted, feed the safety cable between one of the swivel brackets as shown in figure 8. 2. Pull safety cable through and secure cable with safety cable U-bolt as shown in figure 9. 3. Take other end of cable and wrap around beam 4. Secure cable loop as shown in step 2. Be sure there is approximately 2 inches of slack in the safety cable once both ends are secured. 5. Repeat on other side of fan so there are two safety cables. Figure 8: Safety Cable Installation Figure 9: Safety Cable Installation- Close Up HVF Air Circulator User s Manual For customer support, call 1-866-641-4540 www.tractorsupply.com 9
Ceiling Kit Exploded View 30 FLOOR FAN -OPTIONAL CEILING MOUNT 3 2 4 5 6 1 7 8 9 Figure 10: Exploded View of CL-30-DDF (ceiling mount kit) Ceiling Kit Replacement Parts Item# Description Part Number 1 Safety Cable Assy 95-060-0100 2 Nut for Ceiling Swivel Pin 95-060-0180 3 Nut 95-060-0125 4 Upper Ceiling Bracket 95-060-0110 5 U-Bolt 95-060-0120 Item# Description Part Number 6 Top Washer 95-060-0120 7 Lower Ceiling Bracket 95-060-0160 8 Tapping Screw 5-15mm 95-060-0195 9 Ceiling Swivel Pin 95-060-0170 10 www.tractorsupply.com For customer support, call 1-866-641-4540 HVF Air Circulator User s Manual
Troubleshooting Guide Problem Possible Cause Corrective Action Fan does not operate 1. No power Inspect power cord for damage. Be sure unit is plugged in and turned on. 2. Bad motor Replace motor Reduced Air Flow 1. Obstruction Turn off and unplug fan. Remove guard and make sure nothing is obstructing the fan blades. Humming sound but no operation Excess Noise (vibration, squealing) 2. Bad switch or capacitor Replace switch or capacitor (Note: To prolong life of fan, operate fan first in 1(LOW) for 5-10 seconds before switching to higher speed. 1. Bad capacitor Replace capacitor 1. Fan is not on level ground Turn off fan, and move unit to smooth level surface. 2. Guard is not secure Check guard screws to be sure all are tight. HVF Air Circulator User s Manual For customer support, call 1-866-641-4540 www.tractorsupply.com 11
1 YEAR LIMITED WARRANTY The manufacturer warrants this product to the original retail purchaser only, to be free from defects in material and workmanship for a period of one (1) year from the date of initial purchase. This product must be properly installed, maintained and operated in accordance with the instructions provided. The manufacturer requires reasonable proof of your date of purchase from an authorized retailer or distributor. Therefore, you should keep your sales slip, invoice, or cancelled check from the original purchase. This Limited Warranty shall be limited to the repair or replacement of parts, which prove defective under normal use and service within the warranty period, and which the manufacturer shall determine at its reasonable discretion. This warranty does not apply to products purchased for rental use. This Limited Warranty does not cover any failures or operating difficulties due to normal wear and tear, accident, abuse, misuse, alteration, misapplication, improper installation or improper maintenance and service by you or any third party. Failure to perform normal and routine maintenance on the fan, shipping damage, damage related to insects, birds, or animals of any kind, and damage due to weather conditions are also not covered. In addition, the Limited Warranty does not cover damage to the finish, such as scratches, dents, discoloration, rust or other weather damage, after purchase. If the manufacturer finds the item to be in normal operating condition, or not defective, the item will be returned freight collect. This Limited Warranty is in lieu of all other express warranties. The manufacturer disclaims all warranties for products that are purchased from sellers other than authorized retailers or distributors. AFTER THE PERIOD OF THE ONE (1) YEAR LIMITED WARRANTY EXPIRES, THE MANUFACTURER DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR APPLICATION. FURTHER, THE MANUFACTURER SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. The manufacturer assumes no responsibility for any defects caused by third parties. This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other rights depending upon where he or she lives. Some states do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long a warranty lasts, so the above exclusion and limitations may not apply to you. The manufacturer does not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return, or replacement of its equipment, and no such representations are binding on The manufacturer. Always be sure to specify model number and serial number when making any claim with the manufacturer. All transportation costs for the return of the damaged product or parts will be the responsibility of the purchaser. Upon receipt of damaged item, the manufacturer will examine the item and determine if defective. the manufacturer will repair or replace and return the item, freight pre-paid. ALWAYS BE SURE TO SPECIFY MODEL NUMBER AND SERIAL NUMBER WHEN MAKING ANY CLAIM WITH THE MANUFACTURER. FOR YOUR CONVENIENCE USE THE SPACE PROVIDED BELOW TO LIST THIS INFORMATION: Model #: Serial #: Date of Purchase: HVF Air Circulator User s Manual For customer support, call 1-866-641-4540 www.tractorsupply.com